Oesterle MAK8 Kallfass Serra de alimentação de corrente Comprimento máximo de corte 3500mm Comprimento mínimo de corte 585mm Altura de corte 65mm Comprimento máximo do material alimentado na máquina 4500mm Diâmetro da lâmina de serra 300mm Número de unidades de corte 4 Poder das unidades de corte 4x4kw Alimentos materiais para animais por meio de cadeias Velocidade de alimentação ajustável Braçadeiras de material pneumático Remoção de material através de correia transportadora
Prensa hidráulica de chapa aquecida eletricamente modelo HP 65/1, construída em 2006, área de prensagem 2200 x 1100mm, muito pouco utilizada, a partir de operações escolares.
Multi spindle drilling machine Brand: VITAP Type: ALFA DIGIT New machines - QUICK CHANGE SPINDLES - Side reference fences with digital electronic readouts and with manual exclusion for the execution of the system 32 mm drilling holes - Pneumatic cylinder for horizontal/vertical positioning of the boring group - Front caliper with digital electronic readouts - Nr. 2 alu fences with 2 stops each (1500 mm. each) - Quick change fitting of the alu fences with stops - 2 safety clamps inclined 4 degrees - 6 positions turret to adjust the drilling depth (0-80mm) - Height regulation of the boring group by mechanical digital position indicator - Automatic vertical-horizontal depth difference device (10 mm) - Drilling speed adjustment from the panel control - Strengthened steel structure for tilting of the boring group - 1 motor HP. 2 (Kw 1,50) - Start/stop electropne ...
Semi-automatic boring machine Brand: VITAP Typ: ALFA 35 T New machine Technical data: - One boring head 35 spindles - QUICK CHANGE SPINDLES - Pneumatic cylinder for horizontal/vertical positioning of the boring group (45 degreese and any intermediate angles) - Frontal/top 51aliper to obtain the same boring measure between horizontal and vertical position - Tilting side stops adjustable by metric scale and nonius and magnifying lens on each stop - 2 safety clamps inclined 4 degrees - Height regulation of the boring group by mechanical digital position indicator - Stroke regulation by means of 6 positions revolver (turret) (0-80 mm) - Automatic vertical-horizontal depth difference device (10 mm) - Speed regulation of the boring group command by control board - Strengthened steel structures for tilting of the boring group - 1 motor HP. 3 (Kw 2,2) - Sta ...
autom. boring machine Brand: VITAP Type: SIGMA B1 New machine technical detail: - 2800 mm working table - PLC and touch screen - 2 horizontal boring heads with 21 spindles each prepared for quick chucks - 2 motors each 1,5 kW - the right horizontal boring head is movable with the possibility to pass over the vertical boring groups and fitted on prismatic guide with ball bushes and electronic digital indicator. - Digital position indicators for height regulation of the horizontal boring heads - 2 pneumatic stops - changing horizontal/vertical drilling circuit - Belt conveyors fitted on springs sliding on prismatic guide with ball bushes - Front and side pneumatic pushers - Security on line circuit - 700 mm Infeed conveyor - Horizontal movement of the right head by ball bushes guide with electronic digital indicator - Standard accessories - CE standards Dust ...
Dowel hole drilling machine Brand: VITAP Type: ALFA 21 CLASSIC New machine - One boring unit 21 spindles - QUICK CHANGE SPINDLES - Pneumatic cylinder for horizontal/vertical positioning of the boring group (45 degreed and any intermediate angles) - Front/top caliper to obtain the same boring measure between horizontal and vertical position - Tilting side stops adjustable by metric scale and nonius and magnifying lens on each stop - 2 safety clamps inclined 4 degrees - Height regulation of the boring group by mechanical digital position indicator; - 6 positions turret to adjust the drilling depth (0-80 mm) - Automatic vertical-horizontal depth difference device (10 mms) - Drilling speed adjustment from the panel control - Strengthened steel structures for tilting of the boring group - 1 motor HP. 2 (Kw 1,50) - Start/stop electropneumatic circuit by mean ...
New hot press, hydraulically Brand: ITALPRESSE Type XL/6 30-13 PEA Golden electric heating plate surface anodized to ensure high surface hardness and excellent corrision protection. - Electrical - heating plates: 3000 x 1300 mm - Total pressure: 120 to. - Number of hot plates: 2 pc. - Number of floors: 1 pc. - Stroke: 350 mm - Day light opening: 350 mm - All-round feeding - Number of cylinders: 6 pc. - Diameter of cylinder: 85 mm - Power consumption (hydraulic unit): 3 kW - Electric - combi - heating plates made out of two components: Aluminium - electric - heating plate Iso printing plate - Heating power 22 KW - High pressure isolation plates - Operating temperature: 70 - 90° C. - Max. Temperature: 120° C. - Supply: 400V/50 Hz - Safety accordance with CE standard Standard equipment: - Movement of the press table with rack and pinion parallel guidance at t ...
gebr. Kantenanleimmaschine Fabrikat: Format 4 Typ: Tempora 60.12/2 E Baujahr: 2020 -unüberholt- ohne Gwährleistung e- Motion Steuerung Oberer Druckbalken: - Druckbalken aus geschweißter Verwindungsstreifer Stahlkonstruktion. Motorisch gesteuert einstellbare Werkstückhöhe 8-60 mm über e-motion Steuerung. - Glatte,zweireihig versetzt angeordnete Oberdruckrollen, die dafür sorgen,dass eine gleichmäßige Druckverteilung auf das Werkstück stattfindet. - Werkstückabstandüberwachung durch eine Ampel. - Drehteller Kantenmagazin für Rollenkantenmaterial 0,4-3 mm: - Ø des Drehtellers:800 mm - Streifenmagazin für 12 Stück: 10 mm Kanten - Kantenzufuhrung für Rollen- und Streifenmateral tempora Serie - Pneumatisch gesteuertes, Teflonbeschichtetes Leimaggregat für 1,5 Kg EVA Granulat - mit synchronisierter Leimrolle und Schnellwechselsystem. Geeignet f ...
Hot plate press (electric) Brand: ORMA Type: NPC 6/120 new machine Technical data: Heating plates: 3500x1300mm Cylinder: 6 pieces Press force: 120t Stroke/opening dimension: 450mm Connection value: 28.8kW (ELKOM plates) Options: - Intermediate plate - Anodized surface for ELKOM panels - Parallelism sensor á 1,000.00 EUR - Pressing mechanism from above (fixed lower plate) - Max. temperature till 150°C - Max. temperature till 200°C - 4-sided loading possible - Mylar protective film - Fiberglass Teflon protection - Hardware for Industry 4.0
New longitudinal veneer splicer Brand: CASATI Type: LINEA 1250 Technical details: Arm length 1.250 mm Veneer thickness 0,4 - 4 mm Min. veneer length 350 mm Min. veneer width 45 mm Glue for pre-gluing: Urea and PVA Glue for integrated gluing: Urea Feed speed 10 - 40 m/min. Heating area length 1.250 mm Total connected load 7,4 kW Power consumtion approx. 6 kw Compressed air consumption 5 Nl/min Compressed air pressure 6 - 8 bar This machine permits the longitudinal splicing of veneer sheets by applying glue on their edge. Immediately afterwards the veneer will be passing through a heated zone in order to activate the glue reaction: the glue will be hardening thus bonding the veneer sheets. The integrated glueing device allows the joining by one only process. Its also possible to bond pre-glued veneer sheets Option for an extra charge: Cooling device for the glue po ...
Veneer press Brand: ORMA Type: NPC/DIGIT 6/90 New machine Technical datas: Press area: 2500x1300 mm Amount cylinder: 6 Lift & max. press opening: 400 mm Total pressure: 90t Electro-heater 18 kW for thermo-oil (up to 120°C) Optional: - Aluminium coating - 650 mm stroke - Parallelism control by sensor - Extra charge for down stroke design - Extra charge for temperature up to 150°C - Extra charge for temperature up to 200°C - Mylar protection foil 350,00 ? per panel - Pressure plate covered with glass fiber fabric Teflon - Hardware for Industry 4.0
Hot press Make: ORMA Type: NPC/DIGIT 6/95 New machine Technical datas: Press area: 3000x1300 mm Amount cylinder: 6 Lift & max. press opening: 400 mm Total pressure: 90t Electro-heater 18 kW for thermo-oil (120°C) Optional: - Aluminium coating for panels - 650 mm stroke - Parallelism control by sensor - Extra charge for down stroke design - 4 side loading - Max. temperature up to 150°C - Max. temperature up to 200°C - Mylar protection foil - Pressure plate covered with glass fier fabric Teflon - Hardware for Industry 4.0
1 gebr. Kantenbearbeitungsstraße IMA COMBIMA / K/ II/ R75 / 1075 / V / R3 Bj. 1996 Bestehend aus: - Doppelseitige Beschickung BIESSE RBO - Doppelseitige IMA COMBIMA für die Längsbearbeitung: Doppelzerspaner 2 x Fräsen Verleimteil mit Granulat-Vorschmelzer 6-fach Rollen-Magazin für das Kantenmaterial 1 x Hauptandruck- und 4 x Nachpressrolle Kappaggregat Bündfräsen 2 x Feinfräsen Profilziehklinge Flächenziehklinge Schwabbelaggregat Glätteaggregat - Drehvorrichtung von läng auf quer - Doppelseitige IMA COMBIMA für Querbearbeitung Schutzfräsen Doppelzerspannen Nutfräsaggregat Verleimteil mit Granulat-Vorschmelzer 6-fach Rollen-Magazin für das Kantenmaterial 1 x Hauptandruck- und 4 x Nachpressrolle Kappen am Oberdruck (Nachrüstung auf aktuelles Modell) Bündigfräsen Feinfräsen 2 x MFA Fräsen Nutfräsaggregat Profilziehklinge Fl ...
Granulate supply Make: ADOLPH Type: G-Trans 25 for continuous granulate supply on edge banding machines technical details: System for a machine line with 4 pre-melters (standard) Pos.1.1 1 basic unit for bag-emptying G-Trans® 25 Portal for Big-Bags with hanging emptying: Solid steel frame in 40 mm square-tube profile, torsion-stiff welded construction, main pillars with base plate for dowel-anchorage. Solid steel welded construction in square-tube profile, with fork-lift lugs, 4 hooks and tapered guide pins for easy touchdown on the portal. Sufficient stability for 1.500 kg weight. Supporting area with bars and stacking corners. Material container in powder-coated steel, with cone for free-flowing bulk materials. Filler plug diam. 300 mm. Filler opening 350 x 350 mm with sliding cover. 5/8 plugs for granules transport NW 25 Stack frame ...
Single-sided edge banding machine Make: HOMAG Type: KAL 210 AMBITION 2264 Year of construction: 2014 One-sided edge banding machine for editing of straight workpiece edges and for gluing and post-processing in the longitudinal and transverse pass. Overview of aggregate equipment: - Separating agent spray unit - Joining milling unit - Gluing unit A20 with 2 rolls - end trimming unit HL84 - Pre-milling unit BF10 - Form milling unit FK11 manual - Profile scraper PN10 - Finishing unit Feed 18 - 25 m/min. Feed max. with FK11 20 m/min. Working height 950 mm Pneumatic connection 6 bar Total length 7845mm Workpiece thickness 8 - 60 mm Edge height max. = workpiece thickness + 4 mm Edge material roll 0.3 - 3 mm Edge material strips 0.4 - 20 mm Aggregate equipment: - Separating agent spray unit top/bottom - Joining milling unit 2 motors each 3 kW, 150 H ...
Contour edge bander Fabrikat: VITAP Type: BC91 EVO Demonstration machine Technical data: - For straight and curved pieces (convex and concave) - To glue pieces thickness 10-60 mms., in PVC, melamine, veneer, plastic laminate and solid wood - 2 glue spreading rollers - Cutting guillotine up to 3 mm. thickness - Encoder for high precision cutting of the tape ( for shaped closed pieces) - Band length measuring by means of a digital electronic counter - Tape cut by foot pedal to edge just one piece - End switch tape cut (only for straight pieces) - Feeding speed adjustable from 3mt to 20mt per min. - Solid Phenolic table easy to clean and with no transmission of heat - Manual / Automatic band cutting device - Glue pot (kgs. 3), with electronic adjustable heating system -Tilting table 0°-45° - Standard accessories - CE standards
Semi automatic edge bander Make: VITAP Type: FUSION 2.0 New machine Technical datas: - For straight and shaped pieces 10 - 60 mm - Edge thickness 1-3 mm - Tefloned gluing station with quick disassembly system - Glue and tape application on big and small shaped panels - Equipped with glue pot with 1 Kg capacity - 1 glueing roller - 2 rollers to copy the shape of the piece - 1 tilting support roller to enable the exit of the panel after banding - Glue application amount is adjusted via knob - Set up of the glue temperature - Automatic guillotine for coiled material up to 3 mm x 45 mm THREE KIND OF WORKS: - By Encoder - By Encoder + laser - By Pedal cut Panel materials - Solid wood - Chipboard (laminated or not) - Multilayer material - MDF or HDF (laminated or not) - Panel dimensions range: min 50x200mm max 1000x2000 mm - Shaped pieces Dimensions ran ...
Heating- and service table for gluing units Make: Wehrmann Type: VHT for IMA or Homag gluing units - pre-heating of gluing units for fast change - easy cleaning of the glue roll while rotating - better possibility for adjustments when fixing the gluing unit - only 1 x 400 Volt connection needed - rotating of the gluing roll is controlled by the temperature - option for 2 gluing units working parallel - different feeding systems possible - different plug systems on request possible - safety stable because of heavy construction an adjustable feets - very flexible and easy operation - small space need - safe drive by spur gear - swivel-function 7° for emptying of glueing unit Possible execution: - spindle drive: for one or two gluing units - bayonet adapter: for one or two gluing units