subcategorías
(el tercer nivel de categoría)
Fabricante:
(Categoría: 201)
3 stueck unused electric motors for Saeege machines from Rueetschi 380 / 400 Volt 50Hz Dreick circuit 5.5 KW 11.3 A 2850 rpm With tool holder (saege leaf holder) Shaft diameter 30mm Diameter handle for saege leaf (middle) approx.55mm Diameter tool holder outside approx.165mm Total length motor approx. 570mm Total width approx. 200mm Price per piece Hole distance for screwing on the motor laengs 200mm Hole spacing Cross 200mm The abstinfers can be varied in the length and width, because the motor is screwed on to the console via T-slots. The T-slots are located on the motor. Thus, any hole distance would be feasible via a different console. Thread on the motor shaft is right thread (if the nut is in the clockwise, is tightened when the motor is counterclockwise and the mother is hooked- view from the front to the wave) Diameter of the thread approx. 28-30mm. direc ...
1 Post Saegeblaetter (8 Stueck) for Kaltenbach All Saegeblaetter either re-ground or Unused. 1 square diameter 560mm 5 stub diameter 500mm 2 square diameter 400mm Hole in the middle 50mm ... más información
Very good scratch conveyor 80/60/2x 5750 (total length 7m) engine 3 kW ... más información
EWD HDN/SV with width adjustment TOP ZUSTAND ! (1982/2009) WATER-CLOSED FUEHRS, SIDE BRETTERKAPPSAEGE... Through width 735 Passage shoe710 Hub 600 Speed max. 300 Feed speed 0-15 m/min Feed capacity 8.5 m/min Total weight 12 t SPALTKEIL ARTA C WITH SIDE WAREKAPPSAeGE Very well maintained facility little cut ! HDN-SV STATUS: VERY GOOD
1 piece scratch chain foerderer 650/500 mm (W/D) length 38 m; good ... más información
EWD ESTERER HD_30 SVhigh in TOP ZUSTAND ! Repairs 2009, with powerPos.1 frame width 750 mm through shoehe max. 750 mm stroke 600 mmspeed max. (also when idle) 300 rpm Number of rollers 4 pcs. feed 0 - 12 m/min operating side, seen in cutting direction: rightpressure register. machine and base plate in torsional casting construction. gate rollers are divided for easy exchange, hydraulic lifting and lowering of the upper gate rollers, adjustable roll pressure. Electric feed, for stepless regulation the feed speed. central lubrication for all frame guides. Upper guide with water cooling, with water-covering. swing shaft with grease-lubricated roller bearings, flywheel hubs made of high-quality sphaero casting, swing shaft and flywheel hubs in the press bandage. fixed and empty disc for single-space operation. electric slide (0.55 kW). with gate hanging (saegenspanner, saegeblaetter, ...
Esterer DKV 1 movable shaft ! feed hydraulically hydraulic and electrically roller lift: hydraulic power: 55 kW Year construction year: approx. 1982 passage: 750mm = width, 160mm = height 2 x directional laser incl. approx. 15 Circularsaws including with Splitter unit screw roll; good
Plate circular saw Finesse vertical Format 510 x 205 cm 2 seed units (1 x horizontal, 1 x vertical) L x W x H: 620 x 260 x 100 cm Weight approx. 700 kg Built in 1975 The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Pendulum circular saw Irion with roller conveyor Cutting height 100 mm Roller conveyor left 2m Roller conveyor right 3.5 m L x W x H: with roller conveyor 6.0 x 1.2 x 1.5 m Weight approx. 450 kg Year of construction 1965 The machine is in good condition, ready for operation. Subject to change, error, prior sale ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Phone 0041 62 966 18 32 Fax: 0041 62 966 21 12
Cross-cut saw Dewalt 220 V The machine is in good condition, operational. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system+technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Phone: 0041 62 966 18 32 Fax 0041 62 966 21 12
Double mitre saw Omga for glazing beads Ready for pickup, price EXW The machine is in good condition, operational. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system+technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Phone: 0041 62 966 18 32 Fax 0041 62 966 21 12
Table crosscut saw Irion UKS 800 DS Masch. No. 1360 Stop left 7 m Stop right 3.5 m Feeder Roller conveyor 400 mm wide Roll 300 mm long with programming control with documentation with data storage L x W x H Machine: 1650 x 1650 x 1750 mm Built in 1994 The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4952 Eriswil/EN-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Mill mat 4 CH-4952 Eriswil/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Pendulum circular saw Irion Cutting width 350 mm Roller table 3000 mm L x W x H: 600 x 500 x 1800 mm Weight approx. 250 kg Built in 1978 The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Band saw Hunziker Roll ø 800 mm 3.5 HP engine Built 1952 Weight approx. 730 kg L x W x H: 120 x 100 x 230 cm The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Band saw Kirchner Roll á 800 mm Cutting height 300 mm L x W x H: 130 x 80 x 230 cm Weight approx. 750 kg Built in 1944 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Full frame saw Balfour boy with Chuck wagon Wood diameter of exceeding 60 cm Engine 55 kW L x W x H: 230 x 200 x 400 cm Weight approx. 8 to Built in 1958 Disassembly by buyer The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Full frame saw Boegli MARA-2 with Electr. Switchgear with associated Chuck Wagon (REF. No. 262-1491) Masch. No. 373 Through root á 600 mm With hydr. Sheet tensioning device L x W x H: gate 260 x 200 x 450 cmm Weight approx. 1200 to Built in 1978 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Pendulum saws Bacus for wall mounting Saw á 500 mm Built in 1982 L x W x H: 70 x 60 x 100 cm Weight 370 kg The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Multiple lengths saw FAS 14 with 2 circular saw units per 2.2 kW, 3 x 400 V, 50 Hz. -maximum piece length 6000 mm -maximum cutting height 120 mm -maximum Board width 500 mm -Working height 700 mm -Feed speed approx. 0.2 m / sec -Feed drive gear motor 0.55 kW / 3 x 400 V, 50 Hz Built about 1965 Weight 1600 kg Engine No. 314 Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Code: 0669 Brand: CENTAURO Model: R 800 + RVP-200 - CE Standard Industrial band saw with feeder for cutting wooden boards, wooden materials, parquet, beads, skirting boards, joists and wood strips in general - CE Standard - Year 2015 Technical data: Flywheel diameter mm 800 Max cutting height mm 400 Max blade width mm 80 - thickness mm 0,8 Max blade length mm 5530 Table height from floor mm 950 Table size mm 1060 x 800 Motor power Hp 15 Tilting table 15° Diameter of suction ports: n° 2 mm 120 - n° 1 mm 100 Overall dimensions mm 950 x 1550 x 2480 h Weight kg 700 Feeder RVP-200 Technical data: Feeding roller height mm 240 Max roller-blade clearance mm 200 Max fence-blade clearance mm 200 Motor power Kw 0,55 Variable feed speed 1/21 Working pressure 3/5 bar Weight kg 75 Roller table mm 1000 x 800 complete with 3 rollers - diameter 60 mm - independent ...