máquinas e equipamentos para engenharia de processo usadas para venda

- Eirich RV 19 granulation / mixing plant, mixer, feed hopper, riser plate completely refurbished. Incl. -Steel construction - Screw conveyors - Input silo approx. 30 m3 - Steep conveyor  ... mais informação

Motor 75 kW Rotor blades: 5 Bu9dtai0he Stator blades: 2 Rotor diameter: 600 mm Rotor width 780 mm Inlet opening: 720x780 mm ... mais informação

Hollow core granulator and re-cutting mill for pre-shredded material Rotor 450 mm diameter x 600 mm working width 3 rotor blades (bevel cut), 2 stator blades Drive motor 22 kw ... mais informação

-  ... mais informação

Foil cutting mill Propulsion : 30 KW Voltage : 400 V / 3 ~ / 50 Hz  ... mais informação

Grundfos pump, order number 96500570, power, 4 kW/ 50 Hz, good condition - ready for use  ... mais informação

Breast pump stainless steel with housing, manufacturer MKT Malmi, vario gearbox Lenze, electric motor - Elektrokovina T 90L4, power 1.5 kW/220/380 V, special feature: Vario gearbox Lenze  ... mais informação

Sanitary centrifugal pump, Alfa Laval, 222,000 liters per hour, 45 kW, 78 A, approx. 145 kg.  ... mais informação

This Hettich centrifuge was used in a school for milk processing. ... mais informação

Stainless steel centrifugal pump Alfa Laval, type SOLTDC 2/140 SSS, 4,0 kW, used, price ex works  ... mais informação

ERSA HOTFLOW - 7 Continuous dryer / tunnel dryer / belt dryer for drying screen prints on thin films. With separate temperature control of each heating zone at the top and bottom to transport thin films at a constant level, even at high temperatures. Therefore, it is also suitable for large and small formats. Type: HOTFLOW – 7 Convection oven as tunnel dryer / belt dryer / continuous dryer for Drying of board materials on top and bottom. The machine was used to dry screen printing on thin films. 4 heating zones at the top, 4 heating zones at the bottom, for drying on both sides. Each heating zone can be set to its own temperature. Rolling rods at a distance of approx. 4.5 cm on 2 transport chains as support for plates Temperature range from 20° to 300°C Nominal power Pn = 72 KW Rated Current In = 106 A Voltage: 3 x 400/230V Fuse: 3 x 125 A Frequency 50 Hz ...

Glue dosing station MAYER AND MAYER DXR R2020R L-P-PUB PDX20 40-100 P manufactured in 2015 in Germany by MAYER & MAYER HANDELS GMBH. The station was in use for about 3 months in the process. After this time, it was shut down, cleaned and properly secured. All gaskets in the station were replaced with new ones. It is a charging station for manual dispensing / application guns for two-component adhesives. The gun is included for free. Spare parts are offered for the station. Price of the parts to be individually agreed.

A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant Description This is a long gap mill type LGM 4, which can be used for grinding and drying. Origin and Condition The long gap mill was used for several years in our pilot plant as an experimental machine. During this time various products were ground and dried. Technical data Drive power: 18,5 - 55 kW Air volume: 2500 Nm³/h Evaporation capacity: 120 kg/h

A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant We are also interested in buying back disused HOSOKAWA ALPINE machinery Used Hosokawa Alpine Mikro Classifier CC22, from our former generation previous to our current technological evolution. This air classifier can operate off-line as a stand alone system or in-line as the perfect companion for a Hosokawa Alpine ACM 10 or ACM 15 impact classifier mill, to ensure no undesired fine dust particles are present in the final micronized product, usually in the ...

Rental Hosokawa Alpine ACM 2 system by Alpine Rentals. The Hosokawa Alpine Mikro ACM impact classifier mill is perfect for the fine grinding of different dry materials with a precise control over the particle´s top cut thanks to its integrated classifier wheel design. This micronizer can be used to pulverize different coarse products to finer powders and within different industries where micronization might be needed, such as minerals, chemicals, food, pharma, cosmetic, etc. This grinder is able to process coarse products up to approx. 3 Mohs´ hardness by reaching an extremely high end-product fineness values between d97 10 to 120 microns top size (product dependent) at the lowest possible energy consumption. The comminution takes place in the bottom part of the grinding chamber where the rotor plate fitted with grinding tools (hammers or pins) impacts and projects the particles  ...

Fully refurbished Hosokawa Alpine CW 250 used machine by Alpine Originals. The pin mill Hosokawa Alpine Contraplex CW fitted with two driven contrarotating discs. It is used to grind soft materials, even with high fat or humidity content. It allows also the processing of certain flexible materials or those that can´t lose their properties during comminution in cryogenic mode using liquid nitrogen (LN2) freezing them. This micronizer is perfect to pulverize different coarse products down to a finer powder and within different industries where micronization might be needed, such as minerals, chemicals, food, pharma, cosmetics, recycling, etc. This grinder can be used for the pre-cut of different materials. It is able to process coarse products up to approx. 3 Mohs´ hardness by reaching medium to fine particles with end-product fineness values between d97 40 to 500 micrometer (µm) t ...

Rental Hosokawa Alpine UPZ 100 cryogenic system (LN2) by Alpine Rentals. Technical details Design: Non Pressure Shock Resistant (NPSR), non ATEX Suitable for cryogenic grinding with LN2 Material of construction: stainless steel Without wear protection Batch operation, for a few kilos normally (product dependent) Scope of supply 100 UPZ system with grinding tools of choice, small feeding hopper with a dosing channel, cooling screw to feed the LN2, LN2 container, filter and barrel to collect the fines. Includes an operating panel, switch cabinet and a vacuum cleaner. LN2 to be provided on-site This small size system with an universal mill UPZ 100 can be used for the production of small batches as well as for R&D purposes. Thanks to the different grinding accessories it can be adapted to different tasks and target fineness. Suitable for the cryogenic grinding with liquid nit ...

Fully refurbished Hosokawa Alpine UPZ 160 Pharma used system by Alpine Originals. The Hosokawa Alpine Ultraplex UPZ is a universal fine impact mill. It is used to grind soft dry materials. This micronizer is perfect to pulverize different coarse products down to a finer powder and within different industries where micronization might be needed, such as minerals, chemicals, food, pharma, cosmetics, recycling, etc. This grinder can be used for the pre-cut of different materials. It is able to process coarse products up to approx. 3 Mohs´ hardness by reaching medium to fine particles with end-product fineness values between d97 150 to 850 microns (µm) top size (product dependent) at the lowest possible energy consumption. The turbo mill can reach this wide final product range thanks to a variety of easily interchangeable grinding tools such as pin disc, plate beater, beater disc or p ...

Fully refurbished Hosokawa Alpine UPZ 100 used system by Alpine Originals. Technical details Design: Non Pressure Shock Resistant (NPSR), non ATEX, not suitable for inert operation (N2) Material of construction: stainless steel Without wear protection Batch operation, for a few kilos normally (product dependent) Scope of supply 100 UPZ system in large table fitted with pins (other grinding tools of choice could be offered for an additional price), small feeding hopper with a dosing screw, filter and barrel to collect the fines, blower and piping. Includes a relay control panel. This small size system with an universall mill UPZ 100 can be used for the production of small batches as well as for R&D purposes. Thanks to the different grinding accessories it can be adapted to different tasks and target fineness. The Hosokawa Alpine Ultraplex UPZ is a universal fine impact mi ...

Fully refurbished Hosokawa Alpine UPZ 315 used machine by Alpine Originals. The Hosokawa Alpine Ultraplex UPZ is a universal fine impact mill. It is used to grind soft dry materials. This micronizer is perfect to pulverize different coarse products down to a finer powder and within different industries where micronization might be needed, such as minerals, chemicals, food, pharma, cosmetics, recycling, etc. This grinder can be used for the pre-cut of different materials. It is able to process coarse products up to approx. 3 Mohs´ hardness by reaching medium to fine particles with end-product fineness values between d97 150 to 850 microns (µm) top size (product dependent) at the lowest possible energy consumption. The turbo mill can reach this wide final product range thanks to a variety of easily interchangeable grinding tools such as pin disc, plate beater, beater disc or pendulu ...