Fabricante:
(Categoria: 203)
Technical details: - Max. planing width: 500 mm - Maximum chip depth: 5 mm - Length of feed table: 1,300 mm - Length of the take-off table: 1,500 mm - Total length of the table: 2,800 mm - Table height: 800 mm - Max. workpiece length without support: approx. 1.5 m - Length of the joining fence (Aigner joining fence with integrated auxiliary fence): 1,300 mm - Height of the joining stop: 150 mm - Joining stop adjustable up to 45° and extendable over the entire width of the table - Diameter of the TERSA knife shaft: 125 mm - Nominal speed of the TERSA knife shaft: 5,000 rpm - Number of planer blades: 4 pieces - Minimum width of planer blades: 17 mm - Diameter of suction nozzle: 160 mm - Required air velocity: min. 20m/s - Required air volume: 1500 m³/h - Vacuum at 20m/s air velocity: 705 Pa - 6 x machine shoes with adjustment screws - incl. EMERGENCY STOP switch En ...
Weibert fs 52es SPIRAL Dressing thickness planer Planing width 520mm Spiral knife shaft Dressing table length 2250mm Planer fence 1500mm 90°-45° Machine Grey Cast Iron Tables 7 KW (9.5 HP) 400V 50 HZ Thickness table 850x520mm Passage of 3 / 240mm 4 feed speeds 5 / 8 / 12 / 18 m/min Dual folding system of the tables to the rear max. chip removal 5mm Speed 5000 min/1 1 extraction connection 120 mm Weight approx. 700 kg G&STÜ-5503502
From insolvency: Mafell ZH 300 K 380 volts 3500 watts of power Planing width 300mm Machine no.352867 ... mais informação
planing width 630 mm planerhe 200 mm, motorized adjustment 4 - Meswser shaft, connection 7.5 kW, weight 1.5 t; unmaintained ... mais informação
Weibert SD 510 Dressing thickness planer including spiral knife shaft Planer width 510mm Dressing table length 2250mm Planer fence 1500 mm 90°-45° Machine Grey Cast Iron Tables 5.5 KW (7.5 HP) 400V Thicknessing table 1050 x 510mm Passage of 250mm Numerical display thickness table Electric height adjustment of the thickness table 2 infeed speeds 6 & 12 m/min Dual folding system of the tables to the rear Weight of 900 kg G&RO-SD510NE-SPIRAL
Weibert SD 510 Dressing thickness planer including 4-tersa knife shaft Planer width 510mm Dressing table length 2250mm Planer fence 1500 mm 90°-45° Machine Grey Cast Iron Tables 5.5 KW (7.5 HP) 400V Thicknessing table 1050 x 510mm Passage of 250mm Numerical display thickness table Electric height adjustment of the thickness table 2 infeed speeds 6 & 12 m/min Dual folding system of the tables to the rear Weight of 900 kg G&RO-SD510NE-TER
Technical details: - Max. table width: 630 mm - Max. table length: 1,050 mm - Max. planing width: 630 mm - Max. planing height: 250 mm - Diameter of suction nozzle: 140 mm - Diameter knife shaft: 120 mm - 4 x strip planer knife, 820 x 35 x 3 mm - Knife shaft speed: 5,000 rpm - Manual star-delta switching - 2 feed speeds, 9 + 18 m/min (manually adjustable) - Thickness table adjustment manually via handwheel and analogue display (scale) Accessories: - 1 x "BARKOMAT" magnetic tool set for adjusting the planer knives Engine data: - Voltage: 380 V - Current: 16.8 A - Frequency: 50 Hz - Power: 7.5 kW (10.0 hp) - Speed: 2,860 rpm - Feed motor power: 0.9/1.3 kW Dimensions (LxWxH): 1,450 x 1,300 x 1,400 mm (incl. extraction nozzle) Transport dimensions (LxWxH): 1,200 x 1,450 x 1,500 mm (on EURO pallet) Weight: a. 950 kg The machine has been completely cleaned, ove ...
I sell the Weinig Unimat 300 four-sided planer, built in 2004 Feed speed 5-30 m/min. Working width 230mm Working height 130mm 5 Spindle Configuration: bottom - right - left - up - down Combined power 28kW 3-zone pneumatic pressure Good condition. Fully operational! Available soon. Includes full documentation and CE certification.
SCM moulder model SUPERSET 23 with 5 shafts: - Useful working dimensions 230x120mm - Alfasistel electronic control for 2-axis programming - Cardan drive and differentiated pneumatic pressure - Variable feed speed from 4 to 26 m/min - feed unit before the 1st shaft, with quick override - drive roller in the plane after the 5th shaft - 2500mm entrance level - Deck lubrication pump - shafts D=40mm at 6000rpm - Complete with 4 knife heads Trees: - Under HP -right - Left (right+left with single HP engine) - Above HP - Under HP
The machine contains the components from the large-scale series of the powerful WEINIG class Working width 20 – 260 mm / carpentry version Working height 8 – 160 mm 5 working spindles DM 40 mm Long inlet work table - 2000 mm 5 working spindles, bottom 5.5 kW, left + right 7.5 kW, top 7.5 kW, plaster bottom 11 kW Pneum. Pressure of the feed rollers Cardan feed infinitely variable 5 – 24 m/min. ATS system: Up to 98 workpiece dimensions can be programmed and called up at the touch of a button Left and upper spindle drive auto. in position Machine in CE design Built in 1998 Without editing tools
SPECIFICATIONS Pre-planer mm: 2000 Number of spindles: 5 Spindle configuration: I below - week 5,5 II - III right- left - KW 7,5 IV above - week 5,5 V below - week 4,0 Cardan shaft Speed-controlled drive KW: 4.0 Spindle diameter mm: 40 Revolutions per minute: 6,000 Max. working width mm: 230 Max. machining height mm: 120 Complete with: - Soundproof cabin - Grooved table -Tools CE-compliant
Four-sided planer Weinig Hydromat H25N with feeder 100 m/min - German production - hydraulic feed up to 100 m / min - for wet wood - serving table TECHNICAL PARAMETERS: planing width 250 mm planing height 190 mm spindle diameter 50 mm electric height adjustment 1 bottom spindle 15 kW 2 right spindle 7.5 kW 3 left spindle 15 kW 4 right spindle 7.5 kW 5 upper spindle 7.5 kW 6 upper spindle 15 kW 7 bottom spindle 7.5 kW 8 x universal spindle 1800 7.5 kW infinitely adjustable feed rate up to 100 m/min feed pump motor power 22 kW nine rollers in the pulling countertop, three of which in front of the first head seven steel pulling upper rollers four upper rubber pulling rollers pneumatic clamping 1-6-7 spindle joint automatic countertop lubrication feeding table 3000 mm Speed adjustable smoothly up to 100 m/min two upper pneumatic rollers six bo ...
FOUR SIDED PLANER model WEINIG PROFIMAT P 23 E with 5 spindles second hand machine working condition : Excellent CE mark : Yes volt. 380/50 grooved table ( removable ) quick tool locking device with tools : Yes , as in video Composed by 5 spindles , 4 motors : 1° spindle : planer . motor power Hp 5,5 ( Kw 4 ) 2° and 3° spindles : right and left vertical . motor power Hp 7,5 ( Kw 5,5 ) 4° spindle : thickness planer . motor power Hp 10 ( Kw 7,5 ) 5° spindle : planer . motor power Hp 5,5 ( Kw 4 ) grooved table ( removable ) quick tool locking device Technical details : forward motor power Hp 4 ( Kw 3 ) shaft rotation speed rpm 6000 feed speed : from 5 to 24 mt./min. max. useful working width mm. 230 max. useful working height mm. 120 shaft diameter mm.40 inlet length mm. 2000 automatic lubrication system electric height adjustment set of service keys / d ...
530-mm plane width and 4 knife waves quiet run through plane knife waves diameter 125 mms. stable Abrichtanschlag tiltable from 90 ° to 45 ° of highly competitive 5.5 kW of engine S1 . table length 2.9 m Max Spanabnahme, mm 8 Absaugstutzendurchmesser, mm ?160 total weight, kg 800 ... mais informação
Moulder WEINIG model PROFIMAT 23 (260×180) FORTEC, in configuration for carpentry / lamellar processing: – useful working measures 260x180mm – electronic control of 2 axes, SIEMENS programmer SIMATIC OP7 – gimbal towing and differentiated pneumatic pressure – variable feed speed 5 – 24 mt/min – feed motor KW 4 – HP 5,5 – upper feed group before the 1st shaft – lower feed group after the 5th shaft – machine top with air film – short 1050mm entry plane – foot lubrication pump – protection cabin – shafts D=40mm at 6000rpm – complete with tools D = 120mm - Z = 2 Trees: 1- under kw 11 – hp 15 2- Right 3- Left (right and left with single engine kW 11 – HP 15) 4- above kw 11 – hp 15 5- under kw 7,5 – hp 10 Machine according to CE standards
4 CUTTER HEADS, MAX. DIMENSIONS OF THE WORK PIECE: 180/120 MM, MIN. DIMENSINS OF FINISHED WORK PIECE: 16/7 MM, SPINDLE SPEED: 6000 RPM, OPERATION HOURS: 30 HOURS ONLY! ... mais informação
Four-sided planer REX HOMS-410 – made in Germany – for wet wood TECHNICAL PARAMETERS: planing width max. 410 mm planing height on both sides 200 mm planing height on four sides 200 mm spindle diameter 40 mm shaft motor power 2 x 11 kW spindle motor power 2 x 5.5 kW feed speed infinitely adjustable feed speed adjustable on the inverter three upper pulling rollers three lower pulling rollers two auxiliary rollers in the table top brake minimum workpiece length 450 mm dimensions of the machine (length/width/height) 250 / 220 / 180 cm weight ~ 3500 kg
Weibert WJ-FS32-W7 Dressing thickness planer 3-reversible planer knife shaft HSS Motor 3kW 400V 50Hz Passage height: 4-225mm Numerical display of the planing height Planed dressing and thicknessing tables G&2972-2036-W7 ... mais informação
CATALOG NO. 7220 TECHNICAL DATA - min – max width of the processed element 20 – 230mm - min – max height of the processed element 8 – 160mm 7 spindles: 1) horizontal bottom 230mm 5.5kW 2) vertical right 160mm 5.5kW 3) vertical left 160mm 5.5kW 4) vertical right 160mm 5.5kW 5) vertical left 160mm 5.5kW 6) horizontal top 230mm 7.5kW 7) horizontal bottom 230mm 7.5kW - all spindles adjustable up/down, right/left - spindle diameter 40mm - spindle speed 6000 rpm in advance: - 10 pulling, toothed and metal input rollers, including 2 double rollers - 3 side pressures from down: - pressure from the side at the insertion - input shaft, toothed, pulling, turning in the lower tabletop - 2 pressure points from the side - grooved top - drawing roller, metal, grooved - drawing roller, metal, smooth - pneumatically adjustable rollers - length of the introductory tab ...