152 ofertas

Año de construcción: usado
Ubicación: Land-refrigeration screw compressor duopack sab 128 hf - 750 kw

this is a chiller package made by sabroe denmark in 2002, cooling capacity 750 kw, adjustable for 10-100% load. the package consist of two separate liquid cooling screw compressors type sab 128 hf (duopack) with their own electric motor, both operating with r22 refrigerant. units are built on a common base frame with an integrated horizontally mounted common oil separator, oil circulation pump, oil filter, suction- discharge- and safety valves. unit has local control unit unisab iii system. unit was dismantled in year 2014 and is ready for immediate shipment

lubrication oil of the refrigeration compressor is fed to the compressors during the compression process for lubrication, sealing, noise reduction and to remove some of the heat of compression. after the compression process, the oil is separated from the refrigerant in the oil separator. the refrigerant-oil mixture is led into the lower part of the vertical oil separator. there, the first step of oil separation is performed by a combined agglomerator/ demister. the lower part of the oil separator is also used as an oil receiver. the fine separation of the aerosol-type oil portion from the refrigerant is carried out in the upper part of the oil separator by means of coalescing cartridges. the oil separated in the fine section of the oil separator is returned to the compressors suction side via an additional injection orifice.

technical data
manufacturer: york sabroe denmark
manufacturing year: 2002
compressor type: sab 128 hf (duopack)
refrigerant: r 22
cooling capacity: 2 x 379 kw ( 0 /+40c)
swept volume: 2 x 454 m3/h
electric drives (compressor): 2 x 110 kw - 400/690 v 50hz (also suitable for 60hz)
control system: unisab iii REFRIGERATION SCREW COMPRESSOR DUOPACK SAB 128 HF - 750 KW THIS IS A CHILLER PACKAGE MADE BY SABROE DENMARK IN 2002, COOLING CAPACITY 750 KW, ADJUSTABLE FOR 10-100% LOAD. THE PACKAGE CONSIST OF TWO SEPARATE LIQUID COOLING SCREW COMPRESSORS TYPE SAB 128 HF (DUOPACK) WITH THEIR OWN ELECTRIC MOTOR, BOTH OPERATING WITH R22 REFRIGERANT. UNITS ARE BUILT ON A COMMON BASE FRAME WITH AN INTEGRATED HORIZONTALLY MOUNTED COMMON OIL SEPARATOR, OIL CIRCULATION PUMP, OIL FILTER, SUCTION- DISCHARGE- AND SAFETY VALVES. UNIT HAS LOCAL CONTROL UNIT UNISAB III SYSTEM. UNIT WAS DISMANTLED IN YEAR 2014 AND IS READY FOR IMMEDIATE SHIPMENT LUBRICATION OIL OF THE REFRIGERATION COMPRESSOR IS FED TO THE COMPRESSORS DURING THE COMPRESSION PROCESS FOR LUBRICATION, SEALING, NOISE REDUCTION AND TO REMOVE SOME OF THE HEAT OF COMPRESSION. AFTER THE COMPRESSION PROCESS, THE OIL IS SEPARATED FROM THE REFRIGERANT IN THE OIL SEPARATOR. THE REFRIGERANT-OIL MIXTURE IS LED INTO THE LOWER PART OF THE VERTICAL OIL SEPARATOR. THERE, THE FIRST STEP OF OIL SEPARATION IS PERFORMED BY A COMBINED AGGLOMERATOR/ DEMISTER. THE LOWER PART OF THE OIL SEPARATOR IS ALSO USED AS AN OIL RECEIVER. THE FINE SEPARATION OF THE AEROSOL-TYPE OIL PORTION FROM THE REFRIGERANT IS CARRIED OUT IN THE UPPER PART OF THE OIL SEPARATOR BY MEANS OF COALESCING CARTRIDGES. THE OIL SEPARATED IN THE FINE SECTION OF THE OIL SEPARATOR IS RETURNED TO THE COMPRESSORS SUCTION SIDE VIA AN ADDITIONAL INJECTION ORIFICE. TECHNICAL DATA MANUFACTURER: YORK SABROE DENMARK MANUFACTURING YEAR: 2002 COMPRESSOR TYPE: SAB 128 HF (DUOPACK) REFRIGERANT: R 22 COOLING CAPACITY: 2 X 379 KW ( 0 /+40C) SWEPT VOLUME: 2 X 454 M3/H ELECTRIC DRIVES (COMPRESSOR): 2 X 110 KW - 400/690 V 50HZ (ALSO SUITABLE FOR 60HZ) CONTROL SYSTEM: UNISAB III
Vendedor: JADE Trading OY
Año de construcción: usado
Ubicación: Land-computer-controlled, 24 diff. programs, 2 speeds, laminating, dividing and moulding combined in one machine,\r\ndougweight range 65 - 800 gr., cap. 750 - 6300 p./h\r\nproducing of soft- and hard dough, f.e. ciabatta, baguette\r\naccessories: 2 four cylinder-moulders\r\nincl. extender to mould extra-long\r\n\r\ncategory: bakery machine\r\nsales of bakery machines used machines bakery resolution food machine reconditioned condition as it is new\r\n COMPUTER-CONTROLLED, 24 DIFF. PROGRAMS, 2 SPEEDS, LAMINATING, DIVIDING AND MOULDING COMBINED IN ONE MACHINE,\R\NDOUGWEIGHT RANGE 65 - 800 GR., CAP. 750 - 6300 P./H\R\NPRODUCING OF SOFT- AND HARD DOUGH, F.E. CIABATTA, BAGUETTE\R\NACCESSORIES: 2 FOUR CYLINDER-MOULDERS\R\NINCL. EXTENDER TO MOULD EXTRA-LONG\R\N\R\NCATEGORY: BAKERY MACHINE\R\NSALES OF BAKERY MACHINES USED MACHINES BAKERY RESOLUTION FOOD MACHINE RECONDITIONED CONDITION AS IT IS NEW\R\N
Vendedor: Thünnesen GmbH
Año de construcción: usado
Ubicación: Land-glass bottle filling line krones one way 54.000 bph
 
complete line for bottling beer, carbonated and non carbonated soft drinks in one way glass bottles at nominal capacity of 54 000 bph. it was delivered by krones in year 2000 and it was in operation till 2015 and is currently installed and powered. equipment is very well maintaned and it has a complete techncial documentation in english.
 
main characteristics
- capacity 54 000 bph at 0.33 liter bottles
- made by krones in year 2000, in operation till 2015 still installed
- bottle volumes 275, 330 ml and earlier also 660 ml bottles
- total operating hours approx 70.000
- one way line for new glass bottles
- secondary packaging kisters wraparound packer and khs innopac wsp a-m combi packer
- operation controls made with siemens simatic s7 plc system
- overall line efficiency 75 %

list of main equipment:

1. empty bottle pallet transport conveyor system, kensal, year 2010
2. empty bottle depalletiser, kettner pressant universal
- capacity 100 pallets / hour
- layer interleave removal device
- empty pallet stacking device, type 454, model lpmt with max 15 pallet magazine
- empty pallet transport conveyor system
3. empty bottle transport conveyors (mass flow), krones
4. empty bottle transport conveyors/reject lane (single file), krones
5. zero pressure single filer, krones
6. empty bottle inspector krones linatronic
7. filler monobloc (rinser-filler-capper) krones mecafill vk(2v)cf
- short tube filling system for beer and soft drinks with double pre-evacuation before filling
- 132 filling valves, two maxicrown (year 2007) 26 capping stations, one for crown and one for twist off caps
- maxicrown cap feeding system
- inbuilt monoblock cip system
- valve block with buffer tank
- change parts for all bottles sizes
8. full bottle transport conveyor system (filler - pasteuriser), krones
9. full bottle inspector krones checkmat type 707 with swing-push rejection
10. tunnel pasteuriser, sander hansen pb 17.9-504-42, machine number 622
- it has 7 zones total, 4 pasteurization and 3 regerative zones
- total process area 240 m2
- the pasteurizer was refurbished one year ago and it has new martahoon plastic betls and new gear drives.
11. full bottle transport conveyor system (pasteuriser - labellers), krones
12. two bottle driers (air knives)
13. two labelers krones solomatic 018-g88
- combined output between 54.000 bph
- cold glue system, both with two label stations for ready cut paper labels
- rotation l-r and r-l (oposite directions)
- inbuilt no-label checking and rejecting system
- bottle handling change parts and storage racks for parts
14. bottle marking system with
- two videojet inc date coders, model xl 170i uhs af (one for each labeler)
- two domino lazer marker, model dpx1500 digital (one for each labeler)
- two domino digital coder 3, model ddc3l, year 2010 (one for each labeler)
15. two label inspectors, krones checkmat type 707 (one for each line)
16. full bottle transport conveyor system (labelers - kisters) incl. labeler reject conveyor
17. wraparound packer khs kisters innopac wp 070v, year 2005, 70 cycle per min, various configurations with automatic carton feeding system
18. full bottle transport conveyor system (feeding loose bottles to kister combi)
19. khs combi packer, type innopac wsp a-m, year 2011, machine number k-89403431- 000100, max 58 cycles/min, with automatic carton feeding system
20. two finished pack coders, type videojet
21. two lock & pop device made by nordson, in year 2010
22. finished pack transport conveyors
23. finished pack transport spiral elevator made by ambaflex in 2000
24. related electrical control and mcc panels GLASS BOTTLE FILLING LINE KRONES ONE WAY 54.000 BPH COMPLETE LINE FOR BOTTLING BEER, CARBONATED AND NON CARBONATED SOFT DRINKS IN ONE WAY GLASS BOTTLES AT NOMINAL CAPACITY OF 54 000 BPH. IT WAS DELIVERED BY KRONES IN YEAR 2000 AND IT WAS IN OPERATION TILL 2015 AND IS CURRENTLY INSTALLED AND POWERED. EQUIPMENT IS VERY WELL MAINTANED AND IT HAS A COMPLETE TECHNCIAL DOCUMENTATION IN ENGLISH. MAIN CHARACTERISTICS - CAPACITY 54 000 BPH AT 0.33 LITER BOTTLES - MADE BY KRONES IN YEAR 2000, IN OPERATION TILL 2015 STILL INSTALLED - BOTTLE VOLUMES 275, 330 ML AND EARLIER ALSO 660 ML BOTTLES - TOTAL OPERATING HOURS APPROX 70.000 - ONE WAY LINE FOR NEW GLASS BOTTLES - SECONDARY PACKAGING KISTERS WRAPAROUND PACKER AND KHS INNOPAC WSP A-M COMBI PACKER - OPERATION CONTROLS MADE WITH SIEMENS SIMATIC S7 PLC SYSTEM - OVERALL LINE EFFICIENCY 75 % LIST OF MAIN EQUIPMENT: 1. EMPTY BOTTLE PALLET TRANSPORT CONVEYOR SYSTEM, KENSAL, YEAR 2010 2. EMPTY BOTTLE DEPALLETISER, KETTNER PRESSANT UNIVERSAL - CAPACITY 100 PALLETS / HOUR - LAYER INTERLEAVE REMOVAL DEVICE - EMPTY PALLET STACKING DEVICE, TYPE 454, MODEL LPMT WITH MAX 15 PALLET MAGAZINE - EMPTY PALLET TRANSPORT CONVEYOR SYSTEM 3. EMPTY BOTTLE TRANSPORT CONVEYORS (MASS FLOW), KRONES 4. EMPTY BOTTLE TRANSPORT CONVEYORS/REJECT LANE (SINGLE FILE), KRONES 5. ZERO PRESSURE SINGLE FILER, KRONES 6. EMPTY BOTTLE INSPECTOR KRONES LINATRONIC 7. FILLER MONOBLOC (RINSER-FILLER-CAPPER) KRONES MECAFILL VK(2V)CF - SHORT TUBE FILLING SYSTEM FOR BEER AND SOFT DRINKS WITH DOUBLE PRE-EVACUATION BEFORE FILLING - 132 FILLING VALVES, TWO MAXICROWN (YEAR 2007) 26 CAPPING STATIONS, ONE FOR CROWN AND ONE FOR TWIST OFF CAPS - MAXICROWN CAP FEEDING SYSTEM - INBUILT MONOBLOCK CIP SYSTEM - VALVE BLOCK WITH BUFFER TANK - CHANGE PARTS FOR ALL BOTTLES SIZES 8. FULL BOTTLE TRANSPORT CONVEYOR SYSTEM (FILLER - PASTEURISER), KRONES 9. FULL BOTTLE INSPECTOR KRONES CHECKMAT TYPE 707 WITH SWING-PUSH REJECTION 10. TUNNEL PASTEURISER, SANDER HANSEN PB 17.9-504-42, MACHINE NUMBER 622 - IT HAS 7 ZONES TOTAL, 4 PASTEURIZATION AND 3 REGERATIVE ZONES - TOTAL PROCESS AREA 240 M2 - THE PASTEURIZER WAS REFURBISHED ONE YEAR AGO AND IT HAS NEW MARTAHOON PLASTIC BETLS AND NEW GEAR DRIVES. 11. FULL BOTTLE TRANSPORT CONVEYOR SYSTEM (PASTEURISER - LABELLERS), KRONES 12. TWO BOTTLE DRIERS (AIR KNIVES) 13. TWO LABELERS KRONES SOLOMATIC 018-G88 - COMBINED OUTPUT BETWEEN 54.000 BPH - COLD GLUE SYSTEM, BOTH WITH TWO LABEL STATIONS FOR READY CUT PAPER LABELS - ROTATION L-R AND R-L (OPOSITE DIRECTIONS) - INBUILT NO-LABEL CHECKING AND REJECTING SYSTEM - BOTTLE HANDLING CHANGE PARTS AND STORAGE RACKS FOR PARTS 14. BOTTLE MARKING SYSTEM WITH - TWO VIDEOJET INC DATE CODERS, MODEL XL 170I UHS AF (ONE FOR EACH LABELER) - TWO DOMINO LAZER MARKER, MODEL DPX1500 DIGITAL (ONE FOR EACH LABELER) - TWO DOMINO DIGITAL CODER 3, MODEL DDC3L, YEAR 2010 (ONE FOR EACH LABELER) 15. TWO LABEL INSPECTORS, KRONES CHECKMAT TYPE 707 (ONE FOR EACH LINE) 16. FULL BOTTLE TRANSPORT CONVEYOR SYSTEM (LABELERS - KISTERS) INCL. LABELER REJECT CONVEYOR 17. WRAPAROUND PACKER KHS KISTERS INNOPAC WP 070V, YEAR 2005, 70 CYCLE PER MIN, VARIOUS CONFIGURATIONS WITH AUTOMATIC CARTON FEEDING SYSTEM 18. FULL BOTTLE TRANSPORT CONVEYOR SYSTEM (FEEDING LOOSE BOTTLES TO KISTER COMBI) 19. KHS COMBI PACKER, TYPE INNOPAC WSP A-M, YEAR 2011, MACHINE NUMBER K-89403431- 000100, MAX 58 CYCLES/MIN, WITH AUTOMATIC CARTON FEEDING SYSTEM 20. TWO FINISHED PACK CODERS, TYPE VIDEOJET 21. TWO LOCK & POP DEVICE MADE BY NORDSON, IN YEAR 2010 22. FINISHED PACK TRANSPORT CONVEYORS 23. FINISHED PACK TRANSPORT SPIRAL ELEVATOR MADE BY AMBAFLEX IN 2000 24. RELATED ELECTRICAL CONTROL AND MCC PANELS
Vendedor: JADE Trading OY
Año de construcción: usado
Ubicación: Land-chamfered up at the rear,\r\nwith supporting frame with panels on 3 sides.\r\nbelow basin d 535/400 / w 500/400, h 200mm\r\nupper basin d 335/280 / w 500/400, h 280mm\r\ndistance basin from the floor\r\nbelow 525 / upper 1060 mm\r\n\r\ncategory: bakery machine\r\nsales of bakery machines used machines bakery resolution food machine reconditioned condition as it is new\r\n CHAMFERED UP AT THE REAR,\R\NWITH SUPPORTING FRAME WITH PANELS ON 3 SIDES.\R\NBELOW BASIN D 535/400 / W 500/400, H 200MM\R\NUPPER BASIN D 335/280 / W 500/400, H 280MM\R\NDISTANCE BASIN FROM THE FLOOR\R\NBELOW 525 / UPPER 1060 MM\R\N\R\NCATEGORY: BAKERY MACHINE\R\NSALES OF BAKERY MACHINES USED MACHINES BAKERY RESOLUTION FOOD MACHINE RECONDITIONED CONDITION AS IT IS NEW\R\N
Vendedor: Thünnesen GmbH
Año de construcción: usado
Ubicación: Land-this high capacity innoket kl 2080 labeling machine was manufactured in year 2005 by khs gmbh, germany and it is dismantled in year 2013. this labelette has two stations for cold glue labeling system and it suits both for paper and foil applications. this has been used for glass bottles front-back-neck labels. it is controlled by siemens s7 plc combined with khs touch screen operator interface. labeler machine is in good operational condition. note: this labeller has no label orientation unit

technical information:
manufacturer's type: innoket kl 2080/120 - 48 lm gt
manufacturing year: 2005
code number: 1143
capacity: glass bottles 60000 bph
control plc: simatic s7 / 300
operator panel: khs touch screen
frequency converters: danfoss vlt 5000 THIS HIGH CAPACITY INNOKET KL 2080 LABELING MACHINE WAS MANUFACTURED IN YEAR 2005 BY KHS GMBH, GERMANY AND IT IS DISMANTLED IN YEAR 2013. THIS LABELETTE HAS TWO STATIONS FOR COLD GLUE LABELING SYSTEM AND IT SUITS BOTH FOR PAPER AND FOIL APPLICATIONS. THIS HAS BEEN USED FOR GLASS BOTTLES FRONT-BACK-NECK LABELS. IT IS CONTROLLED BY SIEMENS S7 PLC COMBINED WITH KHS TOUCH SCREEN OPERATOR INTERFACE. LABELER MACHINE IS IN GOOD OPERATIONAL CONDITION. NOTE: THIS LABELLER HAS NO LABEL ORIENTATION UNIT TECHNICAL INFORMATION: MANUFACTURER'S TYPE: INNOKET KL 2080/120 - 48 LM GT MANUFACTURING YEAR: 2005 CODE NUMBER: 1143 CAPACITY: GLASS BOTTLES 60000 BPH CONTROL PLC: SIMATIC S7 / 300 OPERATOR PANEL: KHS TOUCH SCREEN FREQUENCY CONVERTERS: DANFOSS VLT 5000
Vendedor: JADE Trading OY
Año de construcción: usado
Precio: used machinery auction RESALE 2.400 €
Ubicación: Land-weight approx.: 14000 kg<br/>dimensions (l x w x h) approx.: 7800 x 12000 x 2050 mm<br/>description: edge thickness: min. 0.4 mm - max. 30 mm, workpiece thickness: min 8 mm - max. 60 mm, workpiece width min. 235 mm, maximum workpiece width approx. 3000 mm, total power: 115 kw, consisting in: 1 x squaring-edging combined machine ecr-216/72-uk9: double-end tenoner for squaring of pieces up to 3000 mm long, with 2 joint trimming units in each side, unilateral edgebander working the pieces for its left side with the following aggregates: gluing unit, edge magazine for 1 edge roller, pressure group with (1+3) rollers, snipping unit, fine trimming unit: 2 x 1.50 kw, profile trimming unit, profile scraper unit, spraying unit, edge buffing unit, 1 x driven roller conveyor 5600 mm long and roller width 2700 mm, 1 x unilateral edgebander uk-9c alu with the following aggregates: gluing unit, edge magazine for 1 edge roller, pressure group with (1+3) rollers, snipping unit, fine trimming unit: 2 x 1.50 kw, profile trimming unit, profile scraper unit, 1 x machine with a edge buffing group WEIGHT APPROX.: 14000 KG
DIMENSIONS (L X W X H) APPROX.: 7800 X 12000 X 2050 MM
DESCRIPTION: EDGE THICKNESS: MIN. 0.4 MM - MAX. 30 MM, WORKPIECE THICKNESS: MIN 8 MM - MAX. 60 MM, WORKPIECE WIDTH MIN. 235 MM, MAXIMUM WORKPIECE WIDTH APPROX. 3000 MM, TOTAL POWER: 115 KW, CONSISTING IN: 1 X SQUARING-EDGING COMBINED MACHINE ECR-216/72-UK9: DOUBLE-END TENONER FOR SQUARING OF PIECES UP TO 3000 MM LONG, WITH 2 JOINT TRIMMING UNITS IN EACH SIDE, UNILATERAL EDGEBANDER WORKING THE PIECES FOR ITS LEFT SIDE WITH THE FOLLOWING AGGREGATES: GLUING UNIT, EDGE MAGAZINE FOR 1 EDGE ROLLER, PRESSURE GROUP WITH (1+3) ROLLERS, SNIPPING UNIT, FINE TRIMMING UNIT: 2 X 1.50 KW, PROFILE TRIMMING UNIT, PROFILE SCRAPER UNIT, SPRAYING UNIT, EDGE BUFFING UNIT, 1 X DRIVEN ROLLER CONVEYOR 5600 MM LONG AND ROLLER WIDTH 2700 MM, 1 X UNILATERAL EDGEBANDER UK-9C ALU WITH THE FOLLOWING AGGREGATES: GLUING UNIT, EDGE MAGAZINE FOR 1 EDGE ROLLER, PRESSURE GROUP WITH (1+3) ROLLERS, SNIPPING UNIT, FINE TRIMMING UNIT: 2 X 1.50 KW, PROFILE TRIMMING UNIT, PROFILE SCRAPER UNIT, 1 X MACHINE WITH A EDGE BUFFING GROUP
Vendedor: Surplex GmbH
Año de construcción: usado
Ubicación: Land-qty. 1 second-hand galvanising and painting plant
mfc.:	danieli & others    type:	galvanising & painting line 		
built:	2001 stopped in 2008		started again in 2017 – stopped in 2018
galvanising section: 	3000 mm² 		width:  	600 to 1500 mm 
thickness: 	0.3 to 3.0 mm 		speed: 	150 m/min
painting section: 	2295 mm²  		width: 		600 to 1500 mm 
	thickness: 	0.3 to 1.5 mm		speed: 	100 m/min
max. temperature: 	850 ºc			max. coil dia.: 2000 mm
 QTY. 1 SECOND-HAND GALVANISING AND PAINTING PLANT MFC.: DANIELI & OTHERS TYPE: GALVANISING & PAINTING LINE BUILT: 2001 STOPPED IN 2008 STARTED AGAIN IN 2017 – STOPPED IN 2018 GALVANISING SECTION: 3000 MM² WIDTH: 600 TO 1500 MM THICKNESS: 0.3 TO 3.0 MM SPEED: 150 M/MIN PAINTING SECTION: 2295 MM² WIDTH: 600 TO 1500 MM THICKNESS: 0.3 TO 1.5 MM SPEED: 100 M/MIN MAX. TEMPERATURE: 850 ºC MAX. COIL DIA.: 2000 MM
Vendedor: MET-TECH GMBH
Año de construcción: usado
Precio: used machinery auction RESALE 2.600 €
Ubicación: Land-weight approx.: 2300 kg<br/>dimensions (l x w x h) approx.: 1900 x 1940 x 2080 mm<br/>description: ? wide belt sander, wide belt sanding machine<br> ? serial number 8279<br> ? total installed power 16.87 kw<br> ? working width 1100 mm<br> ? working height from 2 mm up to 160 mm<br> ? belt conveyor with variable feed speed from 5 m/min up to 20 m/min<br> ? feed motor power 1.50 kw-1400 rpm<br> ? 1st aggregate: 1 grooved steel calibration roller with diameter 150 mm<br> ? 2nd aggregate: 1 combined roller and sanding pad<br> ? motor for 2 groups of 14.72 kw WEIGHT APPROX.: 2300 KG
DIMENSIONS (L X W X H) APPROX.: 1900 X 1940 X 2080 MM
DESCRIPTION: ? WIDE BELT SANDER, WIDE BELT SANDING MACHINE
? SERIAL NUMBER 8279
? TOTAL INSTALLED POWER 16.87 KW
? WORKING WIDTH 1100 MM
? WORKING HEIGHT FROM 2 MM UP TO 160 MM
? BELT CONVEYOR WITH VARIABLE FEED SPEED FROM 5 M/MIN UP TO 20 M/MIN
? FEED MOTOR POWER 1.50 KW-1400 RPM
? 1ST AGGREGATE: 1 GROOVED STEEL CALIBRATION ROLLER WITH DIAMETER 150 MM
? 2ND AGGREGATE: 1 COMBINED ROLLER AND SANDING PAD
? MOTOR FOR 2 GROUPS OF 14.72 KW
Vendedor: Surplex GmbH
Año de construcción: usado
Ubicación: Land-used joinery machine hundegger k2

manufacturer: hundegger, de
type: k2
year of construction: 2001
condition: in good operating

technical data:
information without guarantee
-task - and feeding cross conveyor length: 7.25 m width: 2.2 m maximum wood length: 10.5 m
-lower table swivel caps saw carbide
saw blade 㸠740 mm (11.0 kw) maximum operating depth of saw cuts: 300 mm at 90 Ⱐadjustable processing hub
-universal milling unit
-4-achsig turning plate milling head 㸠350 x 100 mm finger
-drill slot milling tool ã? 3-axis moves 40 x 160 mm with servo drives and positioned (z-axis 550 mm, y-axis 1,400 mm, axis 360â°)
-combined support for vertical working tools with a servo drive, linear guides across movable and up to 5 vertical employees, hub-controlled tool carriage
-combined support for horizontally working tools with a servo drive, on linear guides vertically movable tool carriage can with max 3 units as drilling and slot milling tools are fitted
-2 x drill (2,2 kw) - direction of drilling horizontal drill bit length: 460 mm, max. depth 205 mm; or drill bit length: 650 mm, max. depth 405 mm
-2 x drill (2,2 kw) - direction of drilling vertically from the bottom
-plunge router vertically from the bottom
-marking device from the front + from below with a temperature
- and humidity-independent color pencil, which pneumatically operated, performs accurate cracks
-fully automatic bar turning station - hydraulic (turning up to diameters of up to 300 x 450 mm)
-transport-and positioning device "two-hand system" clip and carriage with ever a 4.7 kw servo motor
-electronic control system with a dust-proof color graphics display, industrial keyboard and usb port.
-6-arm and tray made of profile steel with plastic sliding surfaces, swivel hooked

price on request USED JOINERY MACHINE HUNDEGGER K2 MANUFACTURER: HUNDEGGER, DE TYPE: K2 YEAR OF CONSTRUCTION: 2001 CONDITION: IN GOOD OPERATING TECHNICAL DATA: INFORMATION WITHOUT GUARANTEE -TASK - AND FEEDING CROSS CONVEYOR LENGTH: 7.25 M WIDTH: 2.2 M MAXIMUM WOOD LENGTH: 10.5 M -LOWER TABLE SWIVEL CAPS SAW CARBIDE SAW BLADE &ATILDE;&CEDIL; 740 MM (11.0 KW) MAXIMUM OPERATING DEPTH OF SAW CUTS: 300 MM AT 90 &ACIRC;&DEG; ADJUSTABLE PROCESSING HUB -UNIVERSAL MILLING UNIT -4-ACHSIG TURNING PLATE MILLING HEAD &ATILDE;&CEDIL; 350 X 100 MM FINGER -DRILL SLOT MILLING TOOL &ATILDE;? 3-AXIS MOVES 40 X 160 MM WITH SERVO DRIVES AND POSITIONED (Z-AXIS 550 MM, Y-AXIS 1,400 MM, AXIS 360&ACIRC;&DEG;) -COMBINED SUPPORT FOR VERTICAL WORKING TOOLS WITH A SERVO DRIVE, LINEAR GUIDES ACROSS MOVABLE AND UP TO 5 VERTICAL EMPLOYEES, HUB-CONTROLLED TOOL CARRIAGE -COMBINED SUPPORT FOR HORIZONTALLY WORKING TOOLS WITH A SERVO DRIVE, ON LINEAR GUIDES VERTICALLY MOVABLE TOOL CARRIAGE CAN WITH MAX 3 UNITS AS DRILLING AND SLOT MILLING TOOLS ARE FITTED -2 X DRILL (2,2 KW) - DIRECTION OF DRILLING HORIZONTAL DRILL BIT LENGTH: 460 MM, MAX. DEPTH 205 MM; OR DRILL BIT LENGTH: 650 MM, MAX. DEPTH 405 MM -2 X DRILL (2,2 KW) - DIRECTION OF DRILLING VERTICALLY FROM THE BOTTOM -PLUNGE ROUTER VERTICALLY FROM THE BOTTOM -MARKING DEVICE FROM THE FRONT + FROM BELOW WITH A TEMPERATURE - AND HUMIDITY-INDEPENDENT COLOR PENCIL, WHICH PNEUMATICALLY OPERATED, PERFORMS ACCURATE CRACKS -FULLY AUTOMATIC BAR TURNING STATION - HYDRAULIC (TURNING UP TO DIAMETERS OF UP TO 300 X 450 MM) -TRANSPORT-AND POSITIONING DEVICE "TWO-HAND SYSTEM" CLIP AND CARRIAGE WITH EVER A 4.7 KW SERVO MOTOR -ELECTRONIC CONTROL SYSTEM WITH A DUST-PROOF COLOR GRAPHICS DISPLAY, INDUSTRIAL KEYBOARD AND USB PORT. -6-ARM AND TRAY MADE OF PROFILE STEEL WITH PLASTIC SLIDING SURFACES, SWIVEL HOOKED PRICE ON REQUEST
Vendedor: SN-InTec Ltd.& CO.KG
Año de construcción: usado
Precio: used machinery auction RESALE 650 €
Ubicación: Land-weight approx.: 1000 kg<br/>dimensions (l x w x h) approx.: 2600 x 1600 x 1300 mm<br/>description: surface planer: working width 500 mm, table length 2600 mm, spindle with 4 knives, spindle speed 4500 rpm, tilting guide, motor power 3 kw<br> mortiser: max longitudinal stroke approx. 250 mm, vertical stroke approx. 80 mm WEIGHT APPROX.: 1000 KG
DIMENSIONS (L X W X H) APPROX.: 2600 X 1600 X 1300 MM
DESCRIPTION: SURFACE PLANER: WORKING WIDTH 500 MM, TABLE LENGTH 2600 MM, SPINDLE WITH 4 KNIVES, SPINDLE SPEED 4500 RPM, TILTING GUIDE, MOTOR POWER 3 KW
MORTISER: MAX LONGITUDINAL STROKE APPROX. 250 MM, VERTICAL STROKE APPROX. 80 MM
Vendedor: Surplex GmbH
Año de construcción: usado
Ubicación: Land-workpiece diameter round/ square/ l-shape: 17-32/ 18-30/ 100x8mm, max. workpiece thickness: 13mm, pressing force: 55t, operational pressure: 250bar, nominal power: 4kw, length: 1000mm, width: 680mm, height: 1680mm, weight: 900kg.  WORKPIECE DIAMETER ROUND/ SQUARE/ L-SHAPE: 17-32/ 18-30/ 100X8MM, MAX. WORKPIECE THICKNESS: 13MM, PRESSING FORCE: 55T, OPERATIONAL PRESSURE: 250BAR, NOMINAL POWER: 4KW, LENGTH: 1000MM, WIDTH: 680MM, HEIGHT: 1680MM, WEIGHT: 900KG.
Vendedor: Innovac GmbH
Año de construcción: usado
Precio: used machinery auction RESALE 400 €
Ubicación: Land-weight approx.: 800 kg<br/>dimensions (l x w x h) approx.: 1600 x 1150 x 1030 mm<br/>description: ? 2-fold combined machine<br> ? voltage 220 v<br> ? surface planer: working width 250 mm, table length 1600 mm, entrance table length 780 mm, spindle with 4 knives, tilting guide with dimensions 570 x 100 mm<br> ? thickness planer: working width approx. 300 mm, table length 700 mm, maximum working thickness approx. 140 mm WEIGHT APPROX.: 800 KG
DIMENSIONS (L X W X H) APPROX.: 1600 X 1150 X 1030 MM
DESCRIPTION: ? 2-FOLD COMBINED MACHINE
? VOLTAGE 220 V
? SURFACE PLANER: WORKING WIDTH 250 MM, TABLE LENGTH 1600 MM, ENTRANCE TABLE LENGTH 780 MM, SPINDLE WITH 4 KNIVES, TILTING GUIDE WITH DIMENSIONS 570 X 100 MM
? THICKNESS PLANER: WORKING WIDTH APPROX. 300 MM, TABLE LENGTH 700 MM, MAXIMUM WORKING THICKNESS APPROX. 140 MM
Vendedor: Surplex GmbH
Año de construcción: usado
Ubicación: Land-make: mitutoyo
model: crysta-apex-s 7106 cmm
year: 2014
condition: used
machine type: other 
location of machine: uk 
documentation / manuals included? yes 
condition info: very good condition!

machine details
available as new due to revised project contract.

specifications:
movement range: x axis 705mm y axis 1005mm z axis 605mm

measuring scale resolution: 0.0001mm

traversing speed: 8-300mm/sec per axis 

max combined speed: 520mm/sec

compressed air flow rate: 60nl/min (source 120l/min)

volumetric length measuring accuracy according to iso10360-2 (2009) “ep m//” specification

18-22°c

16-26°c

probe

1.7 + 3l/1000pm

1 7 + 4l/1000 m

mpp310q (64 x 18 mm)

1.7 + 3l/1000pm

1.7 + 4l/1000/m

sp25 (64 x 50 mm)

1.9 + 3l/1000 am

1.9 + 4l/1000 /m

tp200 (64 x 10 mm)

2.2 + 3l/1000 am

2.2 + 4l/1000 am

tp20 (64 x 10 mm)

l = measured length in mm.

machine description
the crysta-apex s is a high accuracy, high speed moving bridge type co-ordinate measuring machine utilising a granite , base, which also provides the y-axis, guide way. a unique design of self-adjusting air bearing is used on each axis to provide excellent stability during high-speed movement and measurement. the moving bridge is constructed of low mass alloy, the “x” beam and “z” spindle external surfaces being impregnated by an oxide coating process to form an   extremely hard surface, which further improves these critical components stability and also provides good wear resistance. power drive is activated via a remote joystick unit for manual drive operation.

each axis can be locked and fine movement adjustment is provided. the measurement system is by mitutoyo srd linear. encoders fitted so as to become an integral part of the machine for thermal stability, and provide a direct digital output of measured data.

the machine is fully equipped for cnc operation via the newly designed machine control unit model uc400 which provides full digital servo control for high speed, high accuracy positioning with 3-axis vector drive and automatic computation of all acceleration and deceleration without operator input.

the controller uses a universal serial bus (usb) connection to simplify computer connectivity and installation.

circular path motion is also provided for continuous movement between relative positions.

twin joystick unit for control of ’x’ and ‘y’ axis movements with second joystick for ‘z’ axis control and optional rotary    table. comprehensive display with control buttons for individual axis locks and speed control. MAKE: MITUTOYO MODEL: CRYSTA-APEX-S 7106 CMM YEAR: 2014 CONDITION: USED MACHINE TYPE: OTHER LOCATION OF MACHINE: UK DOCUMENTATION / MANUALS INCLUDED? YES CONDITION INFO: VERY GOOD CONDITION! MACHINE DETAILS AVAILABLE AS NEW DUE TO REVISED PROJECT CONTRACT. SPECIFICATIONS: MOVEMENT RANGE: X AXIS 705MM Y AXIS 1005MM Z AXIS 605MM MEASURING SCALE RESOLUTION: 0.0001MM TRAVERSING SPEED: 8-300MM/SEC PER AXIS MAX COMBINED SPEED: 520MM/SEC COMPRESSED AIR FLOW RATE: 60NL/MIN (SOURCE 120L/MIN) VOLUMETRIC LENGTH MEASURING ACCURACY ACCORDING TO ISO10360-2 (2009) “EP M//” SPECIFICATION 18-22°C 16-26°C PROBE 1.7 + 3L/1000PM 1 7 + 4L/1000 M MPP310Q (64 X 18 MM) 1.7 + 3L/1000PM 1.7 + 4L/1000/M SP25 (64 X 50 MM) 1.9 + 3L/1000 AM 1.9 + 4L/1000 /M TP200 (64 X 10 MM) 2.2 + 3L/1000 AM 2.2 + 4L/1000 AM TP20 (64 X 10 MM) L = MEASURED LENGTH IN MM. MACHINE DESCRIPTION THE CRYSTA-APEX S IS A HIGH ACCURACY, HIGH SPEED MOVING BRIDGE TYPE CO-ORDINATE MEASURING MACHINE UTILISING A GRANITE , BASE, WHICH ALSO PROVIDES THE Y-AXIS, GUIDE WAY. A UNIQUE DESIGN OF SELF-ADJUSTING AIR BEARING IS USED ON EACH AXIS TO PROVIDE EXCELLENT STABILITY DURING HIGH-SPEED MOVEMENT AND MEASUREMENT. THE MOVING BRIDGE IS CONSTRUCTED OF LOW MASS ALLOY, THE “X” BEAM AND “Z” SPINDLE EXTERNAL SURFACES BEING IMPREGNATED BY AN OXIDE COATING PROCESS TO FORM AN EXTREMELY HARD SURFACE, WHICH FURTHER IMPROVES THESE CRITICAL COMPONENTS STABILITY AND ALSO PROVIDES GOOD WEAR RESISTANCE. POWER DRIVE IS ACTIVATED VIA A REMOTE JOYSTICK UNIT FOR MANUAL DRIVE OPERATION. EACH AXIS CAN BE LOCKED AND FINE MOVEMENT ADJUSTMENT IS PROVIDED. THE MEASUREMENT SYSTEM IS BY MITUTOYO SRD LINEAR. ENCODERS FITTED SO AS TO BECOME AN INTEGRAL PART OF THE MACHINE FOR THERMAL STABILITY, AND PROVIDE A DIRECT DIGITAL OUTPUT OF MEASURED DATA. THE MACHINE IS FULLY EQUIPPED FOR CNC OPERATION VIA THE NEWLY DESIGNED MACHINE CONTROL UNIT MODEL UC400 WHICH PROVIDES FULL DIGITAL SERVO CONTROL FOR HIGH SPEED, HIGH ACCURACY POSITIONING WITH 3-AXIS VECTOR DRIVE AND AUTOMATIC COMPUTATION OF ALL ACCELERATION AND DECELERATION WITHOUT OPERATOR INPUT. THE CONTROLLER USES A UNIVERSAL SERIAL BUS (USB) CONNECTION TO SIMPLIFY COMPUTER CONNECTIVITY AND INSTALLATION. CIRCULAR PATH MOTION IS ALSO PROVIDED FOR CONTINUOUS MOVEMENT BETWEEN RELATIVE POSITIONS. TWIN JOYSTICK UNIT FOR CONTROL OF ’X’ AND ‘Y’ AXIS MOVEMENTS WITH SECOND JOYSTICK FOR ‘Z’ AXIS CONTROL AND OPTIONAL ROTARY TABLE. COMPREHENSIVE DISPLAY WITH CONTROL BUTTONS FOR INDIVIDUAL AXIS LOCKS AND SPEED CONTROL.
Vendedor: CNC Management Ltd
Año de construcción: usado
Precio: used machinery auction RESALE 930 €
Ubicación: Land-weight approx.: 1200 kg<br/>dimensions (l x w x h) approx.: 1600 x 1900 x 950 mm<br/>description: ? wide belt sander, wide belt sanding machine<br> ? serial number 1817<br> ? working width 950 mm<br> ? working height from 4 mm up to 160 mm<br> ? feed motor power 0.45 kw<br> ? 1st aggregate: 1 grooved steel calibration roller with diameter 150 mm<br> ? 2nd aggregate: 1 combined roller and sanding pad aggregate WEIGHT APPROX.: 1200 KG
DIMENSIONS (L X W X H) APPROX.: 1600 X 1900 X 950 MM
DESCRIPTION: ? WIDE BELT SANDER, WIDE BELT SANDING MACHINE
? SERIAL NUMBER 1817
? WORKING WIDTH 950 MM
? WORKING HEIGHT FROM 4 MM UP TO 160 MM
? FEED MOTOR POWER 0.45 KW
? 1ST AGGREGATE: 1 GROOVED STEEL CALIBRATION ROLLER WITH DIAMETER 150 MM
? 2ND AGGREGATE: 1 COMBINED ROLLER AND SANDING PAD AGGREGATE
Vendedor: Surplex GmbH
Año de construcción: usado
Ubicación: Land--electronic hand control module
-ecc package / 12,000 / sk40 - sponsors
-nc rotary table 㸠280 heidenhain
-performance pcb pl 405
-electr. thermal expansion compensation
-discharge device
-tool breakage monitoring
-rotoclear
-oil mist extraction
-chip floating gun (ecc)
-put on rectangular table plate 600 x 370
-measuring probe system sk40 (heidenhain)
-signal lamp with audible signal
-hydraulic extension

workspace
x away the 600 mm
y away 450 mm
z away 450 mm
rapid traverse in x / y / z axis 35 m / min
nc combined table 㸠280 mm
spindle speed (infinitely programmable) 20 - 12000 rpm
spindle taper iso 40
hermle c 600 u - including cab lxwxh 2.50 x 2.02 x 2.75 m
dimensions lxw 4.30 x 3.30 m
weight 6700 kg

-ELECTRONIC HAND CONTROL MODULE -ECC PACKAGE / 12,000 / SK40 - SPONSORS -NC ROTARY TABLE &ATILDE;&CEDIL; 280 HEIDENHAIN -PERFORMANCE PCB PL 405 -ELECTR. THERMAL EXPANSION COMPENSATION -DISCHARGE DEVICE -TOOL BREAKAGE MONITORING -ROTOCLEAR -OIL MIST EXTRACTION -CHIP FLOATING GUN (ECC) -PUT ON RECTANGULAR TABLE PLATE 600 X 370 -MEASURING PROBE SYSTEM SK40 (HEIDENHAIN) -SIGNAL LAMP WITH AUDIBLE SIGNAL -HYDRAULIC EXTENSION WORKSPACE X AWAY THE 600 MM Y AWAY 450 MM Z AWAY 450 MM RAPID TRAVERSE IN X / Y / Z AXIS 35 M / MIN NC COMBINED TABLE &ATILDE;&CEDIL; 280 MM SPINDLE SPEED (INFINITELY PROGRAMMABLE) 20 - 12000 RPM SPINDLE TAPER ISO 40 HERMLE C 600 U - INCLUDING CAB LXWXH 2.50 X 2.02 X 2.75 M DIMENSIONS LXW 4.30 X 3.30 M WEIGHT 6700 KG
Vendedor: Catalano Werkzeugmaschinen AG
Año de construcción: usado
Precio: used machinery auction RESALE 180 €
Ubicación: Land-weight approx.: 600 kg<br/>dimensions (l x w x h) approx.: 1400 x 1330 x 1000 mm<br/>description: ? 2-fold combined machine<br> ? fixed table dimensions 1150 x 530 mm<br> ? sliding table dimensions 1360 x 240 mm<br> ? sliding table travel approx. 1000 mm<br> ? circular saw: max. blade saw diameter approx. 300 mm<br> ? spindle moulder: spindle diameter 50 mm WEIGHT APPROX.: 600 KG
DIMENSIONS (L X W X H) APPROX.: 1400 X 1330 X 1000 MM
DESCRIPTION: ? 2-FOLD COMBINED MACHINE
? FIXED TABLE DIMENSIONS 1150 X 530 MM
? SLIDING TABLE DIMENSIONS 1360 X 240 MM
? SLIDING TABLE TRAVEL APPROX. 1000 MM
? CIRCULAR SAW: MAX. BLADE SAW DIAMETER APPROX. 300 MM
? SPINDLE MOULDER: SPINDLE DIAMETER 50 MM
Vendedor: Surplex GmbH
Año de construcción: usado
Ubicación: Land-it is a used, reconditioned seewer rondo kombi dough sheeter sko 67 with beams circular knitting for sale. the machine is fully operational and new tapes were assembled. the beams round moulder was repainted, new felts are attached to action bar, gutter and transfer funnels.
the combined dough sheeter is suitable for all types of dough and finally rolling out bread for work of all bread dough places, rye, wheat and mixed bread dough with straight final, the long braid, pretzel rods, as well as work by parisian bread roles. also table can be produced. applied dough buns long moulded out.
technical data:
-with extending table
-features manual, continuous roll position
-synchromesh gearbox prevents build up, shrink or tear the dough band
-band width 635 mm
-rollers opening 0.1-45 mm
-roll length 650 mm
-roller adjustment manual
-length 2500 mm for rolling out (working position)
-width: 1150mm
-height: 1300mm
-connection: 400v, 16a-cee plug
-weight approx. 450kg
a video can be sent on request.
dough sheeter and bar round moulder can be purchased individually (on request).

price on request.   IT IS A USED, RECONDITIONED SEEWER RONDO KOMBI DOUGH SHEETER SKO 67 WITH BEAMS CIRCULAR KNITTING FOR SALE. THE MACHINE IS FULLY OPERATIONAL AND NEW TAPES WERE ASSEMBLED. THE BEAMS ROUND MOULDER WAS REPAINTED, NEW FELTS ARE ATTACHED TO ACTION BAR, GUTTER AND TRANSFER FUNNELS. THE COMBINED DOUGH SHEETER IS SUITABLE FOR ALL TYPES OF DOUGH AND FINALLY ROLLING OUT BREAD FOR WORK OF ALL BREAD DOUGH PLACES, RYE, WHEAT AND MIXED BREAD DOUGH WITH STRAIGHT FINAL, THE LONG BRAID, PRETZEL RODS, AS WELL AS WORK BY PARISIAN BREAD ROLES. ALSO TABLE CAN BE PRODUCED. APPLIED DOUGH BUNS LONG MOULDED OUT. TECHNICAL DATA: -WITH EXTENDING TABLE -FEATURES MANUAL, CONTINUOUS ROLL POSITION -SYNCHROMESH GEARBOX PREVENTS BUILD UP, SHRINK OR TEAR THE DOUGH BAND -BAND WIDTH 635 MM -ROLLERS OPENING 0.1-45 MM -ROLL LENGTH 650 MM -ROLLER ADJUSTMENT MANUAL -LENGTH 2500 MM FOR ROLLING OUT (WORKING POSITION) -WIDTH: 1150MM -HEIGHT: 1300MM -CONNECTION: 400V, 16A-CEE PLUG -WEIGHT APPROX. 450KG A VIDEO CAN BE SENT ON REQUEST. DOUGH SHEETER AND BAR ROUND MOULDER CAN BE PURCHASED INDIVIDUALLY (ON REQUEST). PRICE ON REQUEST.
Vendedor: Pick Bäckereimaschinenhandel
Año de construcción: usado
Precio: used machinery auction RESALE 340 €
Ubicación: Land-weight approx.: 240 kg<br/>dimensions (l x w x h) approx.: 930 x 770 x 1700 mm<br/>description: ? inverter air conditioning machine, heat pump<br> ? outdoor unit to combine with indoor units compatible with r410a coolant<br> ? can be combined with more outdoor units<br> ? see picture with technical data<br> ? recently charged coolant WEIGHT APPROX.: 240 KG
DIMENSIONS (L X W X H) APPROX.: 930 X 770 X 1700 MM
DESCRIPTION: ? INVERTER AIR CONDITIONING MACHINE, HEAT PUMP
? OUTDOOR UNIT TO COMBINE WITH INDOOR UNITS COMPATIBLE WITH R410A COOLANT
? CAN BE COMBINED WITH MORE OUTDOOR UNITS
? SEE PICTURE WITH TECHNICAL DATA
? RECENTLY CHARGED COOLANT
Vendedor: Surplex GmbH
Año de construcción: usado
Ubicación: Land-waste heat recovery boilers 8 x 2.9 ton/h at 18 bar

these waste heat recovery boilers were made by selnikel in year 2014. we have six identical boilers from one natural gas engine driven combined cycle power plant, which was shut down in year 2017. these boilers generate 18 bar super-heated steam by recovering heat in the flue gas of engines and this significantly contribute energy efficiency of plant. the boilers have natural circulation and they are designed and manufactured under german eckrohrkessel gmbh license in accordance with en12952 standard, ce marked as per en97/23/ec pressure vessels directive. the boilers are in very good condition.

technical data
manufacturer:	selnikel
manufacturing year:	2014
number of boilers:	8 
type:	superheated steam boiler with water pipes
boiler water circulation:	natural
exhaust inlet flow rate:	23944 kg/h
exhaust inlet temperature:	465 °c
steam production rate:	2940 kg/h (per unit)
steam temperature:	352 °c
steam pressure:	18 bar(g)
heat capacity:	2290 kwth
boiler chimney temperature:	146 °c
pressure loss:	125 mmss
    WASTE HEAT RECOVERY BOILERS 8 X 2.9 TON/H AT 18 BAR THESE WASTE HEAT RECOVERY BOILERS WERE MADE BY SELNIKEL IN YEAR 2014. WE HAVE SIX IDENTICAL BOILERS FROM ONE NATURAL GAS ENGINE DRIVEN COMBINED CYCLE POWER PLANT, WHICH WAS SHUT DOWN IN YEAR 2017. THESE BOILERS GENERATE 18 BAR SUPER-HEATED STEAM BY RECOVERING HEAT IN THE FLUE GAS OF ENGINES AND THIS SIGNIFICANTLY CONTRIBUTE ENERGY EFFICIENCY OF PLANT. THE BOILERS HAVE NATURAL CIRCULATION AND THEY ARE DESIGNED AND MANUFACTURED UNDER GERMAN ECKROHRKESSEL GMBH LICENSE IN ACCORDANCE WITH EN12952 STANDARD, CE MARKED AS PER EN97/23/EC PRESSURE VESSELS DIRECTIVE. THE BOILERS ARE IN VERY GOOD CONDITION. TECHNICAL DATA MANUFACTURER: SELNIKEL MANUFACTURING YEAR: 2014 NUMBER OF BOILERS: 8 TYPE: SUPERHEATED STEAM BOILER WITH WATER PIPES BOILER WATER CIRCULATION: NATURAL EXHAUST INLET FLOW RATE: 23944 KG/H EXHAUST INLET TEMPERATURE: 465 °C STEAM PRODUCTION RATE: 2940 KG/H (PER UNIT) STEAM TEMPERATURE: 352 °C STEAM PRESSURE: 18 BAR(G) HEAT CAPACITY: 2290 KWTH BOILER CHIMNEY TEMPERATURE: 146 °C PRESSURE LOSS: 125 MMSS
Vendedor: JADE Trading OY
Año de construcción: usado
Precio: used machinery auction RESALE 1.900 €
Ubicación: Land-weight approx.: 2900 kg<br/>dimensions (l x w x h) approx.: 1900 x 3100 x 2400 mm<br/>description: ? wide belt sander, wide belt sanding machine<br> ? serial number ae/015956<br> ? working width 1300 mm<br> ? working height from 3 mm up to 160 mm<br> ? vacuum transport belt, ferrari vacuum unit power 5.50 kw<br> ? belt conveyor with variable feed speed<br> ? feed motor power 1.80 kw<br> ? 1st aggregate: 1 grooved steel calibration roller with diameter 180 mm, motor 9.20 kw<br> ? 2nd aggregate: 1 grooved rubber sanding roller with diameter 180 mm, motor 9.20 kw<br> ? 3rd aggregate: 1 combined roller and sanding pad aggregate, motor 9.20 kw WEIGHT APPROX.: 2900 KG
DIMENSIONS (L X W X H) APPROX.: 1900 X 3100 X 2400 MM
DESCRIPTION: ? WIDE BELT SANDER, WIDE BELT SANDING MACHINE
? SERIAL NUMBER AE/015956
? WORKING WIDTH 1300 MM
? WORKING HEIGHT FROM 3 MM UP TO 160 MM
? VACUUM TRANSPORT BELT, FERRARI VACUUM UNIT POWER 5.50 KW
? BELT CONVEYOR WITH VARIABLE FEED SPEED
? FEED MOTOR POWER 1.80 KW
? 1ST AGGREGATE: 1 GROOVED STEEL CALIBRATION ROLLER WITH DIAMETER 180 MM, MOTOR 9.20 KW
? 2ND AGGREGATE: 1 GROOVED RUBBER SANDING ROLLER WITH DIAMETER 180 MM, MOTOR 9.20 KW
? 3RD AGGREGATE: 1 COMBINED ROLLER AND SANDING PAD AGGREGATE, MOTOR 9.20 KW
Vendedor: Surplex GmbH
Año de construcción: usado
Ubicación: Land-steam turbine plant equipment 4450 kwe

this steam turbine power plant equipment was made in 2012-2013 as a part of a natural gas combined cycle power plant. the original power plant was commissioned in november 2012. the steam turbine is condensing type and it is capable of 4450 kw electrical power generation. other equipment consists of a steam condenser, an oil module, a cooling tower for stg’s oil cooler and for condenser, the control panels and a demineralized water preparation unit. all the equipment is in very good condition.

technical data:

steam turbine
manufacturer:	arani
manufacturing year:	2013
model:	api611
type:	impulse, multi-stage, condensing steam turbine

number of units:	1
unit electrical power:	4450 kwe
unit mechanical power:	4500 kwm
steam consumption at full load:	22640 kg/h
steam inlet pressure:	18 bar(a)
steam inlet temperature:	352°c
isentropic efficiency:	88.2% at 100% load
alternator manufacturer:	avk
alternator rated power:	5625 kva
alternator operating voltage:	11 kv

steam condenser
manufacturer:	arani
manufacturing year:	2013
number of units:	1
fluid type:	water / water-glycol (at %20)
design pressure:	0,08 bar(a)
heat transfer surface:	664 m2
thermal power:	4988 kwth
steam flow rate:	22640 kg/h
cooling water flow rate:	1450 m3/h
cooling water inlet temperature:	29 °c
cooling water outlet temperature:	38 °c
steam ejectors:	1 hogger ejector
	2 main first stage ejectors
	2 main second stage ejectors

demineralized water prep. unit
manufacturer:	h?drod?zayn
manufacturing year:	2012
type:	electrodeionization after reverse osmosis
capacity:	30 m3/h
number of units:	1

cooling tower for condenser
manufacturer:	cenk end.
manufacturing year:	2013
model:	2kmf24
type:	reverse flow, water cooled
number of cells:	2
thermal capacity:	13,050,000 kcal/h
water circulation flow rate:	1450 m3/h
water inlet temperature:	38 °c
water outlet temperature:	29 °c
design wet bulb temperature:	23 °c
drift loss:	0.2 %
evaporation loss:	1.2 %
thermal standard:	cti atc 105
barometric pressure:	920 mbar

cooling tower for stg’s oil cooler
manufacturer:	cenk end.
manufacturing year:	2013
model:	1mfk 8x8
type:	water cooled
thermal capacity:	540,000 kcal/h
water circulation flow rate:	60 m3/h
water inlet temperature:	38 °c
water outlet temperature:	29 °c
  STEAM TURBINE PLANT EQUIPMENT 4450 KWE THIS STEAM TURBINE POWER PLANT EQUIPMENT WAS MADE IN 2012-2013 AS A PART OF A NATURAL GAS COMBINED CYCLE POWER PLANT. THE ORIGINAL POWER PLANT WAS COMMISSIONED IN NOVEMBER 2012. THE STEAM TURBINE IS CONDENSING TYPE AND IT IS CAPABLE OF 4450 KW ELECTRICAL POWER GENERATION. OTHER EQUIPMENT CONSISTS OF A STEAM CONDENSER, AN OIL MODULE, A COOLING TOWER FOR STG’S OIL COOLER AND FOR CONDENSER, THE CONTROL PANELS AND A DEMINERALIZED WATER PREPARATION UNIT. ALL THE EQUIPMENT IS IN VERY GOOD CONDITION. TECHNICAL DATA: STEAM TURBINE MANUFACTURER: ARANI MANUFACTURING YEAR: 2013 MODEL: API611 TYPE: IMPULSE, MULTI-STAGE, CONDENSING STEAM TURBINE NUMBER OF UNITS: 1 UNIT ELECTRICAL POWER: 4450 KWE UNIT MECHANICAL POWER: 4500 KWM STEAM CONSUMPTION AT FULL LOAD: 22640 KG/H STEAM INLET PRESSURE: 18 BAR(A) STEAM INLET TEMPERATURE: 352°C ISENTROPIC EFFICIENCY: 88.2% AT 100% LOAD ALTERNATOR MANUFACTURER: AVK ALTERNATOR RATED POWER: 5625 KVA ALTERNATOR OPERATING VOLTAGE: 11 KV STEAM CONDENSER MANUFACTURER: ARANI MANUFACTURING YEAR: 2013 NUMBER OF UNITS: 1 FLUID TYPE: WATER / WATER-GLYCOL (AT %20) DESIGN PRESSURE: 0,08 BAR(A) HEAT TRANSFER SURFACE: 664 M2 THERMAL POWER: 4988 KWTH STEAM FLOW RATE: 22640 KG/H COOLING WATER FLOW RATE: 1450 M3/H COOLING WATER INLET TEMPERATURE: 29 °C COOLING WATER OUTLET TEMPERATURE: 38 °C STEAM EJECTORS: 1 HOGGER EJECTOR 2 MAIN FIRST STAGE EJECTORS 2 MAIN SECOND STAGE EJECTORS DEMINERALIZED WATER PREP. UNIT MANUFACTURER: H?DROD?ZAYN MANUFACTURING YEAR: 2012 TYPE: ELECTRODEIONIZATION AFTER REVERSE OSMOSIS CAPACITY: 30 M3/H NUMBER OF UNITS: 1 COOLING TOWER FOR CONDENSER MANUFACTURER: CENK END. MANUFACTURING YEAR: 2013 MODEL: 2KMF24 TYPE: REVERSE FLOW, WATER COOLED NUMBER OF CELLS: 2 THERMAL CAPACITY: 13,050,000 KCAL/H WATER CIRCULATION FLOW RATE: 1450 M3/H WATER INLET TEMPERATURE: 38 °C WATER OUTLET TEMPERATURE: 29 °C DESIGN WET BULB TEMPERATURE: 23 °C DRIFT LOSS: 0.2 % EVAPORATION LOSS: 1.2 % THERMAL STANDARD: CTI ATC 105 BAROMETRIC PRESSURE: 920 MBAR COOLING TOWER FOR STG’S OIL COOLER MANUFACTURER: CENK END. MANUFACTURING YEAR: 2013 MODEL: 1MFK 8X8 TYPE: WATER COOLED THERMAL CAPACITY: 540,000 KCAL/H WATER CIRCULATION FLOW RATE: 60 M3/H WATER INLET TEMPERATURE: 38 °C WATER OUTLET TEMPERATURE: 29 °C
Vendedor: JADE Trading OY
Año de construcción: usado
Precio: used machinery auction RESALE 320 €
Ubicación: Land-weight approx.: 240 kg<br/>dimensions (l x w x h) approx.: 930 x 770 x 1700 mm<br/>description: ? inverter air conditioning machine, heat pump<br> ? outdoor unit to combine with indoor units compatible with r410a coolant<br> ? can be combined with more outdoor units<br> ? see picture with technical data<br> ? recently charged coolant WEIGHT APPROX.: 240 KG
DIMENSIONS (L X W X H) APPROX.: 930 X 770 X 1700 MM
DESCRIPTION: ? INVERTER AIR CONDITIONING MACHINE, HEAT PUMP
? OUTDOOR UNIT TO COMBINE WITH INDOOR UNITS COMPATIBLE WITH R410A COOLANT
? CAN BE COMBINED WITH MORE OUTDOOR UNITS
? SEE PICTURE WITH TECHNICAL DATA
? RECENTLY CHARGED COOLANT
Vendedor: Surplex GmbH
Año de construcción: usado
Ubicación: Land-seated in the centre, pneumatic clamp h 8.11.20 for the holder and pallets of clamping system of 5000 with clamping pin h 5.611 as well as the minifixplus electrode (with the exception of the range h. 8.180). positioning and repeat accuracy 0,002 mm clamping force (with pneum. after voltage) 60000 n clamping force (without pneum. after voltage) 20000 n clamping force of the central release 2500 n max. work-piece weight 300/50 kg weight approx. 35 kg compressed air 6 bar delivery includes 3 m pneumatic hose, 6 x 1 mm SEATED IN THE CENTRE, PNEUMATIC CLAMP H 8.11.20 FOR THE HOLDER AND PALLETS OF CLAMPING SYSTEM OF 5000 WITH CLAMPING PIN H 5.611 AS WELL AS THE MINIFIXPLUS ELECTRODE (WITH THE EXCEPTION OF THE RANGE H. 8.180). POSITIONING AND REPEAT ACCURACY 0,002 MM CLAMPING FORCE (WITH PNEUM. AFTER VOLTAGE) 60000 N CLAMPING FORCE (WITHOUT PNEUM. AFTER VOLTAGE) 20000 N CLAMPING FORCE OF THE CENTRAL RELEASE 2500 N MAX. WORK-PIECE WEIGHT 300/50 KG WEIGHT APPROX. 35 KG COMPRESSED AIR 6 BAR DELIVERY INCLUDES 3 M PNEUMATIC HOSE, 6 X 1 MM
Vendedor: HORST WOLFF Werkzeugmaschinen
Año de construcción: usado
Precio: used machinery auction RESALE 2.400 €
Ubicación: Land-weight approx.: 575 kg<br/>dimensions (l x w x h) approx.: 2950 x 3400 x 1180 mm<br/>description: ? 5-fold combined machine<br> ? serial number kk/085544<br> ? voltage 220 v<br> ? surface planer: working width 300 mm, table length 1500 mm, entrance table length 730 mm, spindle with 3 knives, spindle speed 5200 rpm, tilting guide with dimensions 1300 x 150 mm<br> ? thickness planer: working width approx. 300 mm, table length 580 mm, maximum working thickness approx. 230 mm<br> ? sliding table saw: max. blade saw diameter 315 mm, rotation speed 4000 rpm, carriage dimensions 2600 x 265 mm, with saw scoring unit, tilting saw, cutting width at rip fence approx. 800 mm<br> ? spindle moulder: spindle diameter 50 mm, 4 rotation speeds: 1400/3500/6000/8000 rpm, max. tool diameter under the table approx. 190 mm, max. tool diameter to tenon approx. 275 mm, useful spindle length approx. 155 mm<br> ? mortiser: table size 430 x 220 mm, max. longitudinal stroke approx. 150 mm, transversal stroke approx. 110 mm, adjustable table height approx. 100 mm WEIGHT APPROX.: 575 KG
DIMENSIONS (L X W X H) APPROX.: 2950 X 3400 X 1180 MM
DESCRIPTION: ? 5-FOLD COMBINED MACHINE
? SERIAL NUMBER KK/085544
? VOLTAGE 220 V
? SURFACE PLANER: WORKING WIDTH 300 MM, TABLE LENGTH 1500 MM, ENTRANCE TABLE LENGTH 730 MM, SPINDLE WITH 3 KNIVES, SPINDLE SPEED 5200 RPM, TILTING GUIDE WITH DIMENSIONS 1300 X 150 MM
? THICKNESS PLANER: WORKING WIDTH APPROX. 300 MM, TABLE LENGTH 580 MM, MAXIMUM WORKING THICKNESS APPROX. 230 MM
? SLIDING TABLE SAW: MAX. BLADE SAW DIAMETER 315 MM, ROTATION SPEED 4000 RPM, CARRIAGE DIMENSIONS 2600 X 265 MM, WITH SAW SCORING UNIT, TILTING SAW, CUTTING WIDTH AT RIP FENCE APPROX. 800 MM
? SPINDLE MOULDER: SPINDLE DIAMETER 50 MM, 4 ROTATION SPEEDS: 1400/3500/6000/8000 RPM, MAX. TOOL DIAMETER UNDER THE TABLE APPROX. 190 MM, MAX. TOOL DIAMETER TO TENON APPROX. 275 MM, USEFUL SPINDLE LENGTH APPROX. 155 MM
? MORTISER: TABLE SIZE 430 X 220 MM, MAX. LONGITUDINAL STROKE APPROX. 150 MM, TRANSVERSAL STROKE APPROX. 110 MM, ADJUSTABLE TABLE HEIGHT APPROX. 100 MM
Vendedor: Surplex GmbH
Año de construcción: usado
Precio: 1.000 
Ubicación: Land-description
sell inverters sma sunny mini central smc 7000tl vdc max 700 v type
vdc mpp 333 - 500v
college no 50/60 hz
idc max 22 has
cap name 7000 w iac no 31a
cos 1

. vde0126.1.1 02.06

price 1000 departure bondy 93 inverter solar smc 7000 tl performant
performance 98% optimal performance of adaptation through regulation optitrac mpp cooling system opticool transformerless flexible phased power classes can be combined with the sunny mini central 9000tl and 10000tl/11000tl is suitable for installation indoor and outdoor switch disconnector dc integrated electronic solar switch (ess) service adm worldwide with service in line input (dc) voltage dc max. 700 v input maximum 22.0 a number of 1s mpp trackers nettle (ac) power ac max 7000 w rated voltage ac 220 v - 240 v ac 50 hz mains frequency / 60 hz performance performance maximum 98.0% interfaces: rs485 optional radio
battery gel, agm, lead, kit and solar panels, converter, charge regulator. solar inverter for injection network

a recovered on rosny under wood 93110 06.89.74.18.83 DESCRIPTION SELL INVERTERS SMA SUNNY MINI CENTRAL SMC 7000TL VDC MAX 700 V TYPE VDC MPP 333 - 500V COLLEGE NO 50/60 HZ IDC MAX 22 HAS CAP NAME 7000 W IAC NO 31A COS 1 . VDE0126.1.1 02.06 PRICE 1000 DEPARTURE BONDY 93 INVERTER SOLAR SMC 7000 TL PERFORMANT PERFORMANCE 98% OPTIMAL PERFORMANCE OF ADAPTATION THROUGH REGULATION OPTITRAC MPP COOLING SYSTEM OPTICOOL TRANSFORMERLESS FLEXIBLE PHASED POWER CLASSES CAN BE COMBINED WITH THE SUNNY MINI CENTRAL 9000TL AND 10000TL/11000TL IS SUITABLE FOR INSTALLATION INDOOR AND OUTDOOR SWITCH DISCONNECTOR DC INTEGRATED ELECTRONIC SOLAR SWITCH (ESS) SERVICE ADM WORLDWIDE WITH SERVICE IN LINE INPUT (DC) VOLTAGE DC MAX. 700 V INPUT MAXIMUM 22.0 A NUMBER OF 1S MPP TRACKERS NETTLE (AC) POWER AC MAX 7000 W RATED VOLTAGE AC 220 V - 240 V AC 50 HZ MAINS FREQUENCY / 60 HZ PERFORMANCE PERFORMANCE MAXIMUM 98.0% INTERFACES: RS485 OPTIONAL RADIO BATTERY GEL, AGM, LEAD, KIT AND SOLAR PANELS, CONVERTER, CHARGE REGULATOR. SOLAR INVERTER FOR INJECTION NETWORK A RECOVERED ON ROSNY UNDER WOOD 93110 06.89.74.18.83
Vendedor: negomat industrie
Año de construcción: usado
Precio: used machinery auction RESALE 350 €
Ubicación: Land-weight approx.: 400 kg<br/>dimensions (l x w x h) approx.: 2300 x 820 x 1040 mm<br/>description: ? surface planer<br> ? working width 400 mm<br> ? table length 2300 mm<br> ? entrance table length 1250 mm<br> ? tilting guide with dimensions 890 x 120 mm<br> ? portable, with wheels WEIGHT APPROX.: 400 KG
DIMENSIONS (L X W X H) APPROX.: 2300 X 820 X 1040 MM
DESCRIPTION: ? SURFACE PLANER
? WORKING WIDTH 400 MM
? TABLE LENGTH 2300 MM
? ENTRANCE TABLE LENGTH 1250 MM
? TILTING GUIDE WITH DIMENSIONS 890 X 120 MM
? PORTABLE, WITH WHEELS
Vendedor: Surplex GmbH
Año de construcción: usado
Precio: 12.000 €
Ubicación: Land-mixture cooler of gea maschinenkã¼hltechnik type 10109601 MIXTURE COOLER OF GEA MASCHINENK&ATILDE;&FRAC14;HLTECHNIK TYPE 10109601
Vendedor: Intma GmbH
Año de construcción: usado
Precio: used machinery auction RESALE 650 €
Ubicación: Land-weight approx.: 1200 kg<br/>dimensions (l x w x h) approx.: 3200 x 3000 x 1800 mm<br/>description: serial number 230743, 1 x end cutting saw unit - motor 2.20 kw - blade saw diameter 400 mm - adjustable height, 2 x horizontal planer spindles top-bottom with spindle diameter 30 mm each - motor 2.20 kw - adjustable height, 1 x vertical spindle unit - motor 5.50 kw - spindle diameter 40 mm, table 1000 x 500 mm, 2 pneumatic clamping cylinders, extendable parallel stop, total length approx. 2500 mm, table adjustable to left- and right-side WEIGHT APPROX.: 1200 KG
DIMENSIONS (L X W X H) APPROX.: 3200 X 3000 X 1800 MM
DESCRIPTION: SERIAL NUMBER 230743, 1 X END CUTTING SAW UNIT - MOTOR 2.20 KW - BLADE SAW DIAMETER 400 MM - ADJUSTABLE HEIGHT, 2 X HORIZONTAL PLANER SPINDLES TOP-BOTTOM WITH SPINDLE DIAMETER 30 MM EACH - MOTOR 2.20 KW - ADJUSTABLE HEIGHT, 1 X VERTICAL SPINDLE UNIT - MOTOR 5.50 KW - SPINDLE DIAMETER 40 MM, TABLE 1000 X 500 MM, 2 PNEUMATIC CLAMPING CYLINDERS, EXTENDABLE PARALLEL STOP, TOTAL LENGTH APPROX. 2500 MM, TABLE ADJUSTABLE TO LEFT- AND RIGHT-SIDE
Vendedor: Surplex GmbH
Año de construcción: usado
Precio: 4.950 €
Ubicación: Land-combined saw, milling machine -, planing, drilling machine

planing width 310 mm
cutting length 865 mm
shaper fence for tool 㸠max 220 mm
built in 2008
weight 450 kg
l x w x h: 1.8 x 1.3 x 1.5 m

the machine is in good condition, ready to use.

subject to changes, errors, prior sale!

service/spare parts by matec ch-4952 eriswil/de-79618 rheinfelden

matec system + technology gmbh
mechanical engineering
mill mat 4
ch-4952 eriswil/switzerland

tel. 0041 62 966 18 32
fax 0041 62 966 21 12 
 COMBINED SAW, MILLING MACHINE -, PLANING, DRILLING MACHINE PLANING WIDTH 310 MM CUTTING LENGTH 865 MM SHAPER FENCE FOR TOOL &ATILDE;&CEDIL; MAX 220 MM BUILT IN 2008 WEIGHT 450 KG L X W X H: 1.8 X 1.3 X 1.5 M THE MACHINE IS IN GOOD CONDITION, READY TO USE. SUBJECT TO CHANGES, ERRORS, PRIOR SALE! SERVICE/SPARE PARTS BY MATEC CH-4952 ERISWIL/DE-79618 RHEINFELDEN MATEC SYSTEM + TECHNOLOGY GMBH MECHANICAL ENGINEERING MILL MAT 4 CH-4952 ERISWIL/SWITZERLAND TEL. 0041 62 966 18 32 FAX 0041 62 966 21 12
Vendedor: MATEC system+technik GmbH
Año de construcción: usado
Ubicación: Land-pulling capacity: 10 t<br/>working area: 10 - 25 mm<br/>speed: - 28 m/min<br/>combined drawing machine with flying shear<br/><br/>make: schumag<br/>type: kz-rp 2a<br/>construction year: 1966/1980<br/><br/>pulling force:           10 to.<br/>working area bars:       10 - 25 mm<br/><br/>finished lengths:        6  m/max<br/>drawing speed:           infinitely variable up to 28 m / min.<br/><br/><br/>the plant consists of:<br/>=======================<br/>- pre-straightener driven<br/>- hydraulic push-in device<br/>- drawn part with gearbox and motor 90 kw<br/>- horizontal and vertical directional<br/>- flying shear<br/>- outlet table<br/>- collecting rack<br/>- electrical cabinet<br/><br/>several spare parts and accessories are included.<br/><br/><br/>total weight:  approx. 20 to.<br/><br/><br/><br/><small>the data for this ad was created with modulmws - the software solution of logotech ohg.</small><br/> PULLING CAPACITY: 10 T
WORKING AREA: 10 - 25 MM
SPEED: - 28 M/MIN
COMBINED DRAWING MACHINE WITH FLYING SHEAR

MAKE: SCHUMAG
TYPE: KZ-RP 2A
CONSTRUCTION YEAR: 1966/1980

PULLING FORCE: 10 TO.
WORKING AREA BARS: 10 - 25 MM

FINISHED LENGTHS: 6 M/MAX
DRAWING SPEED: INFINITELY VARIABLE UP TO 28 M / MIN.


THE PLANT CONSISTS OF:
=======================
- PRE-STRAIGHTENER DRIVEN
- HYDRAULIC PUSH-IN DEVICE
- DRAWN PART WITH GEARBOX AND MOTOR 90 KW
- HORIZONTAL AND VERTICAL DIRECTIONAL
- FLYING SHEAR
- OUTLET TABLE
- COLLECTING RACK
- ELECTRICAL CABINET

SEVERAL SPARE PARTS AND ACCESSORIES ARE INCLUDED.


TOTAL WEIGHT: APPROX. 20 TO.



THE DATA FOR THIS AD WAS CREATED WITH MODULMWS - THE SOFTWARE SOLUTION OF LOGOTECH OHG.
Vendedor: Teutenberg Maschinen GmbH & Co.KG
Año de construcción: usado
Ubicación: Land-bitzer / alfa laval l7sw1s12pp

product number:m19-4335
cooling capacity:930 kw
refrigerant:nh3/r717
refrigerant content:80 kg
voltage:400 volt
motor power:250 kw
dimensions:9.000x3.000x2.600 mm
weight:13.500 kg
year:2014
number in stock:4 piece(s)
price:quotation request

very nice and young bitzer water-cooled ammonia water chiller(s) built in a machine-room container with mechanical cooling. this bitzer chiller consists of a frequency controlled bitzer screw compressor (brand danfoss), weg electric motor 250 kw, horizontal oil separator, oil cooler, combined economiser/liquid separator, alfa laval plate heat exchanger evaporator, alfa laval plate heat exchanger condenser, grundfos speed controlled pumps and a control cabinet with siemens plc and touch screen.
the above mentioned capacity is at +18/12°c in/out and a flow rate of 143,7 m3/h. and a cooling water supply +40°c in (out +48°c) and flow rate of 119,5 m3/h. both cold water and cooling water are filled with 30% glycol. for the layout drawing, p&id and name plates of the chiller see pdf!
if you want additional information, you can send us an email or call us.

please also visit our website: used-refrigeration   BITZER / ALFA LAVAL L7SW1S12PP PRODUCT NUMBER:M19-4335 COOLING CAPACITY:930 KW REFRIGERANT:NH3/R717 REFRIGERANT CONTENT:80 KG VOLTAGE:400 VOLT MOTOR POWER:250 KW DIMENSIONS:9.000X3.000X2.600 MM WEIGHT:13.500 KG YEAR:2014 NUMBER IN STOCK:4 PIECE(S) PRICE:QUOTATION REQUEST VERY NICE AND YOUNG BITZER WATER-COOLED AMMONIA WATER CHILLER(S) BUILT IN A MACHINE-ROOM CONTAINER WITH MECHANICAL COOLING. THIS BITZER CHILLER CONSISTS OF A FREQUENCY CONTROLLED BITZER SCREW COMPRESSOR (BRAND DANFOSS), WEG ELECTRIC MOTOR 250 KW, HORIZONTAL OIL SEPARATOR, OIL COOLER, COMBINED ECONOMISER/LIQUID SEPARATOR, ALFA LAVAL PLATE HEAT EXCHANGER EVAPORATOR, ALFA LAVAL PLATE HEAT EXCHANGER CONDENSER, GRUNDFOS SPEED CONTROLLED PUMPS AND A CONTROL CABINET WITH SIEMENS PLC AND TOUCH SCREEN. THE ABOVE MENTIONED CAPACITY IS AT +18/12°C IN/OUT AND A FLOW RATE OF 143,7 M3/H. AND A COOLING WATER SUPPLY +40°C IN (OUT +48°C) AND FLOW RATE OF 119,5 M3/H. BOTH COLD WATER AND COOLING WATER ARE FILLED WITH 30% GLYCOL. FOR THE LAYOUT DRAWING, P&ID AND NAME PLATES OF THE CHILLER SEE PDF! IF YOU WANT ADDITIONAL INFORMATION, YOU CAN SEND US AN EMAIL OR CALL US. PLEASE ALSO VISIT OUR WEBSITE: USED-REFRIGERATION
Vendedor: VRT International B.V.
Año de construcción: usado
Ubicación: Land-amtec vertiwrap combined metal detector / weigh checker<br><br>combination of metal detector and weigh checker. with two recect devices to check if product metallic impurities and/or meets target weight. <br><br> specifications: stainless steel framework, weight range: 5-990g | detecting speed 0.2-0.75m/sec | detecting accuracy: fe from Ø 1.0mm, sus from Ø 2.0mm | target weight accuracy: ± 0.5g | tunnel size wxh: 330x150mm | max. passing size wxh: 280x110mm | power: 220v/0.35kw, 50hz/60hz | dimensions and weight: l1700xw600xh900mm, 160/260kg.<br><br>our machines are available as sample, exhibition or demonstration machines and available directly from stock/overstock. sometimes also not yet fully finished systems are available that can be finished according to your specifications. deviations from the sample photo are possible. an intermediate sale is reserved. - all machines are available with full warranty. AMTEC VERTIWRAP COMBINED METAL DETECTOR / WEIGH CHECKER

COMBINATION OF METAL DETECTOR AND WEIGH CHECKER. WITH TWO RECECT DEVICES TO CHECK IF PRODUCT METALLIC IMPURITIES AND/OR MEETS TARGET WEIGHT.

SPECIFICATIONS: STAINLESS STEEL FRAMEWORK, WEIGHT RANGE: 5-990G | DETECTING SPEED 0.2-0.75M/SEC | DETECTING ACCURACY: FE FROM Ø 1.0MM, SUS FROM Ø 2.0MM | TARGET WEIGHT ACCURACY: ± 0.5G | TUNNEL SIZE WXH: 330X150MM | MAX. PASSING SIZE WXH: 280X110MM | POWER: 220V/0.35KW, 50HZ/60HZ | DIMENSIONS AND WEIGHT: L1700XW600XH900MM, 160/260KG.

OUR MACHINES ARE AVAILABLE AS SAMPLE, EXHIBITION OR DEMONSTRATION MACHINES AND AVAILABLE DIRECTLY FROM STOCK/OVERSTOCK. SOMETIMES ALSO NOT YET FULLY FINISHED SYSTEMS ARE AVAILABLE THAT CAN BE FINISHED ACCORDING TO YOUR SPECIFICATIONS. DEVIATIONS FROM THE SAMPLE PHOTO ARE POSSIBLE. AN INTERMEDIATE SALE IS RESERVED. - ALL MACHINES ARE AVAILABLE WITH FULL WARRANTY.
Vendedor: BluePack Machines GmbH
Año de construcción: usado
Ubicación: Land-genset included tem evo control panel, main gas line, optional exhaust gas heat exchanger, gas optional exhaust cleaner hanwel brand, optional silencer, optionally oiltank fresh and old. allrelated documentation. GENSET INCLUDED TEM EVO CONTROL PANEL, MAIN GAS LINE, OPTIONAL EXHAUST GAS HEAT EXCHANGER, GAS OPTIONAL EXHAUST CLEANER HANWEL BRAND, OPTIONAL SILENCER, OPTIONALLY OILTANK FRESH AND OLD. ALLRELATED DOCUMENTATION.
Vendedor: Wermers Consultancy
Año de construcción: usado
Ubicación: Land-amtec vertiwrap net clipping machine for fruits, vegetables and industrial products 0.5-5.0kg<br><br>auto clipping machine to pack fruits and vegetables as well as industrial products into netting sleeves which are closed at both ends by a metallic staple/clip. suitable to be combined as infeed system: amtec vertiwrap auto dosing machine for fruits, vegetables, etc.- at least, at one of the tops, a labelling/identification tag is placed. - possibility of an automatic change of tube (suitable to carry 200m of net), controlled by a motor. net extraction through a sliding system with two gears: a slow for making the pack and a fast one for getting back the remaining net and returning to the start position. very regular pack size for very flexible net being supplied form net pipe with diameter of 200mm. suitable for packs of 0.5-5.0kg. control panel for easy operation. <br><br> specifications: max. speed of the machine in neutral: 35 cycles/minute | power: 380v, 2.9kw | air: 1.5m³/min, 6bar | machine dimensions: l1840xw720xh2010mm | weight: 425kg.<br><br>our machines are available as sample, exhibition or demonstration machines and available directly from stock/overstock. sometimes also not yet fully finished systems are available that can be finished according to your specifications. deviations from the sample photo are possible. an intermediate sale is reserved. - all machines are available with full warranty. AMTEC VERTIWRAP NET CLIPPING MACHINE FOR FRUITS, VEGETABLES AND INDUSTRIAL PRODUCTS 0.5-5.0KG

AUTO CLIPPING MACHINE TO PACK FRUITS AND VEGETABLES AS WELL AS INDUSTRIAL PRODUCTS INTO NETTING SLEEVES WHICH ARE CLOSED AT BOTH ENDS BY A METALLIC STAPLE/CLIP. SUITABLE TO BE COMBINED AS INFEED SYSTEM: AMTEC VERTIWRAP AUTO DOSING MACHINE FOR FRUITS, VEGETABLES, ETC.- AT LEAST, AT ONE OF THE TOPS, A LABELLING/IDENTIFICATION TAG IS PLACED. - POSSIBILITY OF AN AUTOMATIC CHANGE OF TUBE (SUITABLE TO CARRY 200M OF NET), CONTROLLED BY A MOTOR. NET EXTRACTION THROUGH A SLIDING SYSTEM WITH TWO GEARS: A SLOW FOR MAKING THE PACK AND A FAST ONE FOR GETTING BACK THE REMAINING NET AND RETURNING TO THE START POSITION. VERY REGULAR PACK SIZE FOR VERY FLEXIBLE NET BEING SUPPLIED FORM NET PIPE WITH DIAMETER OF 200MM. SUITABLE FOR PACKS OF 0.5-5.0KG. CONTROL PANEL FOR EASY OPERATION.

SPECIFICATIONS: MAX. SPEED OF THE MACHINE IN NEUTRAL: 35 CYCLES/MINUTE | POWER: 380V, 2.9KW | AIR: 1.5M³/MIN, 6BAR | MACHINE DIMENSIONS: L1840XW720XH2010MM | WEIGHT: 425KG.

OUR MACHINES ARE AVAILABLE AS SAMPLE, EXHIBITION OR DEMONSTRATION MACHINES AND AVAILABLE DIRECTLY FROM STOCK/OVERSTOCK. SOMETIMES ALSO NOT YET FULLY FINISHED SYSTEMS ARE AVAILABLE THAT CAN BE FINISHED ACCORDING TO YOUR SPECIFICATIONS. DEVIATIONS FROM THE SAMPLE PHOTO ARE POSSIBLE. AN INTERMEDIATE SALE IS RESERVED. - ALL MACHINES ARE AVAILABLE WITH FULL WARRANTY.
Vendedor: BluePack Machines GmbH
Año de construcción: usado
Ubicación: Land-genset panel mastwercontrol included, main gas line, optional exhaust heat exchanger, optional gas condensor, all related documentation. installation can be inspected in running conditioning till august 2019. GENSET PANEL MASTWERCONTROL INCLUDED, MAIN GAS LINE, OPTIONAL EXHAUST HEAT EXCHANGER, OPTIONAL GAS CONDENSOR, ALL RELATED DOCUMENTATION. INSTALLATION CAN BE INSPECTED IN RUNNING CONDITIONING TILL AUGUST 2019.
Vendedor: Wermers Consultancy
Año de construcción: usado
Ubicación: Land-amtec shrinktunnel pe-xl new<br><br>large shrinking tunnel for pe or pvc wrapped products. suitable to be combined with many sleeveshrink machines (e.g. amtec sleeveshrink s25 a automatic new). <br><br> specifications: power supply: 380v,22kw | max. speed of the machine in neutral: 12m/minute | max. product size: w450xh330mm | machine dimensions: l4000xw900xh1700mm | weight: 560kg.<br><br>our machines are available as sample, exhibition or demonstration machines and available directly from stock/overstock. sometimes also not yet fully finished systems are available that can be finished according to your specifications. deviations from the sample photo are possible. an intermediate sale is reserved. - all machines are available with full warranty. AMTEC SHRINKTUNNEL PE-XL NEW

LARGE SHRINKING TUNNEL FOR PE OR PVC WRAPPED PRODUCTS. SUITABLE TO BE COMBINED WITH MANY SLEEVESHRINK MACHINES (E.G. AMTEC SLEEVESHRINK S25 A AUTOMATIC NEW).

SPECIFICATIONS: POWER SUPPLY: 380V,22KW | MAX. SPEED OF THE MACHINE IN NEUTRAL: 12M/MINUTE | MAX. PRODUCT SIZE: W450XH330MM | MACHINE DIMENSIONS: L4000XW900XH1700MM | WEIGHT: 560KG.

OUR MACHINES ARE AVAILABLE AS SAMPLE, EXHIBITION OR DEMONSTRATION MACHINES AND AVAILABLE DIRECTLY FROM STOCK/OVERSTOCK. SOMETIMES ALSO NOT YET FULLY FINISHED SYSTEMS ARE AVAILABLE THAT CAN BE FINISHED ACCORDING TO YOUR SPECIFICATIONS. DEVIATIONS FROM THE SAMPLE PHOTO ARE POSSIBLE. AN INTERMEDIATE SALE IS RESERVED. - ALL MACHINES ARE AVAILABLE WITH FULL WARRANTY.
Vendedor: BluePack Machines GmbH
Año de construcción: usado
Ubicación: Land-genset included diana xt control panel, gasline, optionally exhaustgas heat exchanger, fan cooler 2nd stage inter cooler, all related documentation. GENSET INCLUDED DIANA XT CONTROL PANEL, GASLINE, OPTIONALLY EXHAUSTGAS HEAT EXCHANGER, FAN COOLER 2ND STAGE INTER COOLER, ALL RELATED DOCUMENTATION.
Vendedor: Wermers Consultancy
Año de construcción: usado
Ubicación: Land-amtec shrinktunnel-pe-xl<br><br>large shrinking tunnel for pe or pvc wrapped products. suitable to be combined with all sleeveshrink machines (single ones/except s10 and s6). <br><br> specifications: power: 380v, 24kw | max. speed : 0-13m/min | max. product size: w450xh350mm | machine dimensions: l2800xw900xh1720mm | weight: 550/600kg.<br><br>our machines are available as sample, exhibition or demonstration machines and available directly from stock/overstock. sometimes also not yet fully finished systems are available that can be finished according to your specifications. deviations from the sample photo are possible. an intermediate sale is reserved. - all machines are available with full warranty. AMTEC SHRINKTUNNEL-PE-XL

LARGE SHRINKING TUNNEL FOR PE OR PVC WRAPPED PRODUCTS. SUITABLE TO BE COMBINED WITH ALL SLEEVESHRINK MACHINES (SINGLE ONES/EXCEPT S10 AND S6).

SPECIFICATIONS: POWER: 380V, 24KW | MAX. SPEED : 0-13M/MIN | MAX. PRODUCT SIZE: W450XH350MM | MACHINE DIMENSIONS: L2800XW900XH1720MM | WEIGHT: 550/600KG.

OUR MACHINES ARE AVAILABLE AS SAMPLE, EXHIBITION OR DEMONSTRATION MACHINES AND AVAILABLE DIRECTLY FROM STOCK/OVERSTOCK. SOMETIMES ALSO NOT YET FULLY FINISHED SYSTEMS ARE AVAILABLE THAT CAN BE FINISHED ACCORDING TO YOUR SPECIFICATIONS. DEVIATIONS FROM THE SAMPLE PHOTO ARE POSSIBLE. AN INTERMEDIATE SALE IS RESERVED. - ALL MACHINES ARE AVAILABLE WITH FULL WARRANTY.
Vendedor: BluePack Machines GmbH
Año de construcción: usado
Ubicación: Land-genset included diana xt control panel, main gas line and pre-chamber gas line, gas compressor included pressure vessel, exhaust connection gas pipe, pumps, valves, compensators, all related documentation.
installation is running till week 46, conditioning can therefore be inspected in running. GENSET INCLUDED DIANA XT CONTROL PANEL, MAIN GAS LINE AND PRE-CHAMBER GAS LINE, GAS COMPRESSOR INCLUDED PRESSURE VESSEL, EXHAUST CONNECTION GAS PIPE, PUMPS, VALVES, COMPENSATORS, ALL RELATED DOCUMENTATION. INSTALLATION IS RUNNING TILL WEEK 46, CONDITIONING CAN THEREFORE BE INSPECTED IN RUNNING.
Vendedor: Wermers Consultancy
Año de construcción: usado
Ubicación: Land-amtec shrinktunnel pof-xxxl (high speed) pro-version<br><br>pro-version shrink tunnel to heat shrink very large and wide products with polyolefin film in higher speed. suitable to be combined with amtec shrink wrapper sideshrink w60xxxl pro-version. double air circulation, adjustable air flow, suitable for large products and/or high speed packaging (recommended for sideshrink and flowshrink machines). <br><br> specifications: max. product dimensions: l(unlimited)x1100xh230mm | tunnel size: l2400xw1200xh280mm | machine dimensions: l2400xw1600xh1260mm | power consumption: 380v, 28kw.<br><br>our machines are available as sample, exhibition or demonstration machines and available directly from stock/overstock. sometimes also not yet fully finished systems are available that can be finished according to your specifications. deviations from the sample photo are possible. an intermediate sale is reserved. - all machines are available with full warranty. AMTEC SHRINKTUNNEL POF-XXXL (HIGH SPEED) PRO-VERSION

PRO-VERSION SHRINK TUNNEL TO HEAT SHRINK VERY LARGE AND WIDE PRODUCTS WITH POLYOLEFIN FILM IN HIGHER SPEED. SUITABLE TO BE COMBINED WITH AMTEC SHRINK WRAPPER SIDESHRINK W60XXXL PRO-VERSION. DOUBLE AIR CIRCULATION, ADJUSTABLE AIR FLOW, SUITABLE FOR LARGE PRODUCTS AND/OR HIGH SPEED PACKAGING (RECOMMENDED FOR SIDESHRINK AND FLOWSHRINK MACHINES).

SPECIFICATIONS: MAX. PRODUCT DIMENSIONS: L(UNLIMITED)X1100XH230MM | TUNNEL SIZE: L2400XW1200XH280MM | MACHINE DIMENSIONS: L2400XW1600XH1260MM | POWER CONSUMPTION: 380V, 28KW.

OUR MACHINES ARE AVAILABLE AS SAMPLE, EXHIBITION OR DEMONSTRATION MACHINES AND AVAILABLE DIRECTLY FROM STOCK/OVERSTOCK. SOMETIMES ALSO NOT YET FULLY FINISHED SYSTEMS ARE AVAILABLE THAT CAN BE FINISHED ACCORDING TO YOUR SPECIFICATIONS. DEVIATIONS FROM THE SAMPLE PHOTO ARE POSSIBLE. AN INTERMEDIATE SALE IS RESERVED. - ALL MACHINES ARE AVAILABLE WITH FULL WARRANTY.
Vendedor: BluePack Machines GmbH
Año de construcción: usado
Ubicación: Land-genset included tem evo control panel, main gas line, optional exhaust exchanger exhaust heat, optional first and second silencer and chimney, optionally oiltank fresh and old, all related documentation. GENSET INCLUDED TEM EVO CONTROL PANEL, MAIN GAS LINE, OPTIONAL EXHAUST EXCHANGER EXHAUST HEAT, OPTIONAL FIRST AND SECOND SILENCER AND CHIMNEY, OPTIONALLY OILTANK FRESH AND OLD, ALL RELATED DOCUMENTATION.
Vendedor: Wermers Consultancy
Año de construcción: usado
Ubicación: Land-amtec shrinktunnel pof-xl (high speed) pro-version<br><br>pro-version shrink tunnel to heat shrink products with polyolefin film in higher speed. suitable to be combined with amtec shrink wrapper speed shrink w40xl (vertical) pro-version and amtec shrink wrapper sideshrink w60xxl pro-version. double air circulation, adjustable air flow, suitable for large products and/or high speed packaging (recommended also for sideshrink and flowshrink machines). <br><br> specifications: max. product dimensions: l(unlimited)xw700xh300mm | tunnel size: l1700xw790xh350mm | machine dimensions: l2200xw1400xh1230mm | power consumption: 380v, 21kw.<br><br>our machines are available as sample, exhibition or demonstration machines and available directly from stock/overstock. sometimes also not yet fully finished systems are available that can be finished according to your specifications. deviations from the sample photo are possible. an intermediate sale is reserved. - all machines are available with full warranty. AMTEC SHRINKTUNNEL POF-XL (HIGH SPEED) PRO-VERSION

PRO-VERSION SHRINK TUNNEL TO HEAT SHRINK PRODUCTS WITH POLYOLEFIN FILM IN HIGHER SPEED. SUITABLE TO BE COMBINED WITH AMTEC SHRINK WRAPPER SPEED SHRINK W40XL (VERTICAL) PRO-VERSION AND AMTEC SHRINK WRAPPER SIDESHRINK W60XXL PRO-VERSION. DOUBLE AIR CIRCULATION, ADJUSTABLE AIR FLOW, SUITABLE FOR LARGE PRODUCTS AND/OR HIGH SPEED PACKAGING (RECOMMENDED ALSO FOR SIDESHRINK AND FLOWSHRINK MACHINES).

SPECIFICATIONS: MAX. PRODUCT DIMENSIONS: L(UNLIMITED)XW700XH300MM | TUNNEL SIZE: L1700XW790XH350MM | MACHINE DIMENSIONS: L2200XW1400XH1230MM | POWER CONSUMPTION: 380V, 21KW.

OUR MACHINES ARE AVAILABLE AS SAMPLE, EXHIBITION OR DEMONSTRATION MACHINES AND AVAILABLE DIRECTLY FROM STOCK/OVERSTOCK. SOMETIMES ALSO NOT YET FULLY FINISHED SYSTEMS ARE AVAILABLE THAT CAN BE FINISHED ACCORDING TO YOUR SPECIFICATIONS. DEVIATIONS FROM THE SAMPLE PHOTO ARE POSSIBLE. AN INTERMEDIATE SALE IS RESERVED. - ALL MACHINES ARE AVAILABLE WITH FULL WARRANTY.
Vendedor: BluePack Machines GmbH
Año de construcción: usado
Precio: 12.500 €
Ubicación: Land-see drawing/picture SEE DRAWING/PICTURE
Vendedor: Wermers Consultancy
Año de construcción: usado
Ubicación: Land-amtec shrinktunnel pof-xxl (high speed) pro-version<br><br>pro-version shrink tunnel to heat shrink very large products with polyolefin film in higher speed. suitable to be combined with amtec shrink wrapper speed shrink w40xxl (vertical) pro-version. double air circulation, adjustable air flow, suitable for large products and/or high speed packaging (recommended for sideshrink and flowshrink machines). <br><br> specifications: max. product dimensions: l(unlimited)xw800xh300mm | tunnel size: l2400xw850xh400mm | machine dimensions: l2400xw1320xh1750mm | power consumption: 380v, 24kw.<br><br>our machines are available as sample, exhibition or demonstration machines and available directly from stock/overstock. sometimes also not yet fully finished systems are available that can be finished according to your specifications. deviations from the sample photo are possible. an intermediate sale is reserved. - all machines are available with full warranty. AMTEC SHRINKTUNNEL POF-XXL (HIGH SPEED) PRO-VERSION

PRO-VERSION SHRINK TUNNEL TO HEAT SHRINK VERY LARGE PRODUCTS WITH POLYOLEFIN FILM IN HIGHER SPEED. SUITABLE TO BE COMBINED WITH AMTEC SHRINK WRAPPER SPEED SHRINK W40XXL (VERTICAL) PRO-VERSION. DOUBLE AIR CIRCULATION, ADJUSTABLE AIR FLOW, SUITABLE FOR LARGE PRODUCTS AND/OR HIGH SPEED PACKAGING (RECOMMENDED FOR SIDESHRINK AND FLOWSHRINK MACHINES).

SPECIFICATIONS: MAX. PRODUCT DIMENSIONS: L(UNLIMITED)XW800XH300MM | TUNNEL SIZE: L2400XW850XH400MM | MACHINE DIMENSIONS: L2400XW1320XH1750MM | POWER CONSUMPTION: 380V, 24KW.

OUR MACHINES ARE AVAILABLE AS SAMPLE, EXHIBITION OR DEMONSTRATION MACHINES AND AVAILABLE DIRECTLY FROM STOCK/OVERSTOCK. SOMETIMES ALSO NOT YET FULLY FINISHED SYSTEMS ARE AVAILABLE THAT CAN BE FINISHED ACCORDING TO YOUR SPECIFICATIONS. DEVIATIONS FROM THE SAMPLE PHOTO ARE POSSIBLE. AN INTERMEDIATE SALE IS RESERVED. - ALL MACHINES ARE AVAILABLE WITH FULL WARRANTY.
Vendedor: BluePack Machines GmbH
Año de construcción: usado
Ubicación: Land-for the professional processing of wood or wood-like surfaces.

features:
1 combined grinding unit with:
-an automatically serving, profiled
steel contact roller with grain size compensation
to calibrate, 160 mm diameter
-an electronically controlled
limb pressure bar segment width 35 mm,.
for fine grinding
-cutting speed 18 m/s.
-80 mm wide grinding usage (felt 0.55)
-belt feed with infinitely variable feed speed, 2.5-13 m / min
-pneum.. belt tension with integrated belt edge compensation
-touch-screen display with 125 free programmable memory locations
-consistent workpiece infeed height by
adjustment of the upper part of the machine
-plate (900 mm) folding, with role
-finish brush spout side

technical data:
working width: 1350 mm
workpiece infeed height: 900 mm
tape exchange page links
workpiece thickness of 3-160 mm
belt width: 1370 mm
belt length: 2150 mm
operating voltage: 400 v / 50 hz
drive motor unit: 15 kw
dust nozzle:
1 x dm 180 mm (unit 1)
suction capacity: about 1,830 m â³/h FOR THE PROFESSIONAL PROCESSING OF WOOD OR WOOD-LIKE SURFACES. FEATURES: 1 COMBINED GRINDING UNIT WITH: -AN AUTOMATICALLY SERVING, PROFILED STEEL CONTACT ROLLER WITH GRAIN SIZE COMPENSATION TO CALIBRATE, 160 MM DIAMETER -AN ELECTRONICALLY CONTROLLED LIMB PRESSURE BAR SEGMENT WIDTH 35 MM,. FOR FINE GRINDING -CUTTING SPEED 18 M/S. -80 MM WIDE GRINDING USAGE (FELT 0.55) -BELT FEED WITH INFINITELY VARIABLE FEED SPEED, 2.5-13 M / MIN -PNEUM.. BELT TENSION WITH INTEGRATED BELT EDGE COMPENSATION -TOUCH-SCREEN DISPLAY WITH 125 FREE PROGRAMMABLE MEMORY LOCATIONS -CONSISTENT WORKPIECE INFEED HEIGHT BY ADJUSTMENT OF THE UPPER PART OF THE MACHINE -PLATE (900 MM) FOLDING, WITH ROLE -FINISH BRUSH SPOUT SIDE TECHNICAL DATA: WORKING WIDTH: 1350 MM WORKPIECE INFEED HEIGHT: 900 MM TAPE EXCHANGE PAGE LINKS WORKPIECE THICKNESS OF 3-160 MM BELT WIDTH: 1370 MM BELT LENGTH: 2150 MM OPERATING VOLTAGE: 400 V / 50 HZ DRIVE MOTOR UNIT: 15 KW DUST NOZZLE: 1 X DM 180 MM (UNIT 1) SUCTION CAPACITY: ABOUT 1,830 M &ACIRC;&SUP3;/H
Vendedor: Maschinen-Kaul GmbH & Co.KG
Año de construcción: usado
Ubicación: Land-amtec shrinktunnel-pof-m (high speed) pro-version (for speed-m and flowshrink)<br><br>pro-version shrink tunnel to heat shrink products with polyolefin film in higher speed. suitable to be combined with amtec shrink wrapper speed shrink w40m (vertical) pro-version, amtec shrink wrapper flowshrink w100-l high speed pro-version. double air circulation, adjustable air flow, suitable for large products and/or high speed packaging (recommended for sideshrink and flowshrink machines). <br><br> specifications: max. product dimensions: l(unlimited)xw300xh230mm | tunnel size: l1200xw350xh380mm | machine dimensions: l2200xw900xh1160mm | power consumption: 380v, 14kw.<br><br>our machines are available as sample, exhibition or demonstration machines and available directly from stock/overstock. sometimes also not yet fully finished systems are available that can be finished according to your specifications. deviations from the sample photo are possible. an intermediate sale is reserved. - all machines are available with full warranty. AMTEC SHRINKTUNNEL-POF-M (HIGH SPEED) PRO-VERSION (FOR SPEED-M AND FLOWSHRINK)

PRO-VERSION SHRINK TUNNEL TO HEAT SHRINK PRODUCTS WITH POLYOLEFIN FILM IN HIGHER SPEED. SUITABLE TO BE COMBINED WITH AMTEC SHRINK WRAPPER SPEED SHRINK W40M (VERTICAL) PRO-VERSION, AMTEC SHRINK WRAPPER FLOWSHRINK W100-L HIGH SPEED PRO-VERSION. DOUBLE AIR CIRCULATION, ADJUSTABLE AIR FLOW, SUITABLE FOR LARGE PRODUCTS AND/OR HIGH SPEED PACKAGING (RECOMMENDED FOR SIDESHRINK AND FLOWSHRINK MACHINES).

SPECIFICATIONS: MAX. PRODUCT DIMENSIONS: L(UNLIMITED)XW300XH230MM | TUNNEL SIZE: L1200XW350XH380MM | MACHINE DIMENSIONS: L2200XW900XH1160MM | POWER CONSUMPTION: 380V, 14KW.

OUR MACHINES ARE AVAILABLE AS SAMPLE, EXHIBITION OR DEMONSTRATION MACHINES AND AVAILABLE DIRECTLY FROM STOCK/OVERSTOCK. SOMETIMES ALSO NOT YET FULLY FINISHED SYSTEMS ARE AVAILABLE THAT CAN BE FINISHED ACCORDING TO YOUR SPECIFICATIONS. DEVIATIONS FROM THE SAMPLE PHOTO ARE POSSIBLE. AN INTERMEDIATE SALE IS RESERVED. - ALL MACHINES ARE AVAILABLE WITH FULL WARRANTY.
Vendedor: BluePack Machines GmbH
Año de construcción: usado
Ubicación: Land--working width 1100 mm
-a sanding belt, 1,900 x 1,110 mm
-combined contact roller pressure shoe unit - height-adjustable contact roller - roll at the inlet
-cleaning brush in the spout
-suction nozzle 㸠2 x 200 mm -WORKING WIDTH 1100 MM -A SANDING BELT, 1,900 X 1,110 MM -COMBINED CONTACT ROLLER PRESSURE SHOE UNIT - HEIGHT-ADJUSTABLE CONTACT ROLLER - ROLL AT THE INLET -CLEANING BRUSH IN THE SPOUT -SUCTION NOZZLE &ATILDE;&CEDIL; 2 X 200 MM
Vendedor: Maschinen-Kaul GmbH & Co.KG
Año de construcción: usado
Ubicación: Land-amtec shrinktunnel pof-l (high speed) pro-version<br><br>pro-version shrink tunnel to heat shrink products with polyolefin film in higher speed. suitable to be combined with amtec shrink wrapper speed shrink w40l (vertical) pro-version and amtec shrink wrapper sideshrink w60xl pro-version. conveyor speed: 0-30m/min. adjustable air flow, suitable for large products and/or high speed packaging (recommended for sideshrink and flowshrink machines). - max. product dimensions: l(unlimited)xw400xh300mm | tunnel size: l1700xw450xh350mm | machine dimensions: l2200xw1000xh1330mm | power consumption: 380v, 16kw.<br><br>our machines are available as sample, exhibition or demonstration machines and available directly from stock/overstock. sometimes also not yet fully finished systems are available that can be finished according to your specifications. deviations from the sample photo are possible. an intermediate sale is reserved. - all machines are available with full warranty. AMTEC SHRINKTUNNEL POF-L (HIGH SPEED) PRO-VERSION

PRO-VERSION SHRINK TUNNEL TO HEAT SHRINK PRODUCTS WITH POLYOLEFIN FILM IN HIGHER SPEED. SUITABLE TO BE COMBINED WITH AMTEC SHRINK WRAPPER SPEED SHRINK W40L (VERTICAL) PRO-VERSION AND AMTEC SHRINK WRAPPER SIDESHRINK W60XL PRO-VERSION. CONVEYOR SPEED: 0-30M/MIN. ADJUSTABLE AIR FLOW, SUITABLE FOR LARGE PRODUCTS AND/OR HIGH SPEED PACKAGING (RECOMMENDED FOR SIDESHRINK AND FLOWSHRINK MACHINES). - MAX. PRODUCT DIMENSIONS: L(UNLIMITED)XW400XH300MM | TUNNEL SIZE: L1700XW450XH350MM | MACHINE DIMENSIONS: L2200XW1000XH1330MM | POWER CONSUMPTION: 380V, 16KW.

OUR MACHINES ARE AVAILABLE AS SAMPLE, EXHIBITION OR DEMONSTRATION MACHINES AND AVAILABLE DIRECTLY FROM STOCK/OVERSTOCK. SOMETIMES ALSO NOT YET FULLY FINISHED SYSTEMS ARE AVAILABLE THAT CAN BE FINISHED ACCORDING TO YOUR SPECIFICATIONS. DEVIATIONS FROM THE SAMPLE PHOTO ARE POSSIBLE. AN INTERMEDIATE SALE IS RESERVED. - ALL MACHINES ARE AVAILABLE WITH FULL WARRANTY.
Vendedor: BluePack Machines GmbH
Año de construcción: usado
Ubicación: Land- -from above dragging, 1 belt - sanding belt dimensions 1100 mm wide, 1900 mm long, working width 1100 mm - 1 combined contact rollers sanding shoe unit, drive motor 15 kw, with height-adjustable contact roller 85â° shore, and electronically-controlled limb pressure bar, element width d.p.a 50 mm - grinding belt grit compensation contact roller - belt drive with automatic star delta starting and maintenance-free, verschleiã?loser electric brake device optical, airless belt control. 
-pneumatic belt tensioner - belt feed device, powered by infinitely variable geared motor, speeds 2.5-12.5 m / min. and automatic control system for the belt run - led digital display device of the workpiece thickness adjustment- leds indicating the operational readiness - 1 rotating brush at the outlet side of the machine - separated arranged dust suction hoses and nozzles for the sanding belt (dm 200 mm) and the cleaning brush (dm 200 mm) - with complete pneumatic control , including automatic pressure switch, control and monitoring devices - all electrical controls - main switch, fuses, contactor control with motor protection relay, display devices - vde - execution - power consumption: approx. 17 kw -. operating voltage: 380 v, 50 hz. 
 -FROM ABOVE DRAGGING, 1 BELT - SANDING BELT DIMENSIONS 1100 MM WIDE, 1900 MM LONG, WORKING WIDTH 1100 MM - 1 COMBINED CONTACT ROLLERS SANDING SHOE UNIT, DRIVE MOTOR 15 KW, WITH HEIGHT-ADJUSTABLE CONTACT ROLLER 85&ACIRC;&DEG; SHORE, AND ELECTRONICALLY-CONTROLLED LIMB PRESSURE BAR, ELEMENT WIDTH D.P.A 50 MM - GRINDING BELT GRIT COMPENSATION CONTACT ROLLER - BELT DRIVE WITH AUTOMATIC STAR DELTA STARTING AND MAINTENANCE-FREE, VERSCHLEI&ATILDE;?LOSER ELECTRIC BRAKE DEVICE OPTICAL, AIRLESS BELT CONTROL. -PNEUMATIC BELT TENSIONER - BELT FEED DEVICE, POWERED BY INFINITELY VARIABLE GEARED MOTOR, SPEEDS 2.5-12.5 M / MIN. AND AUTOMATIC CONTROL SYSTEM FOR THE BELT RUN - LED DIGITAL DISPLAY DEVICE OF THE WORKPIECE THICKNESS ADJUSTMENT- LEDS INDICATING THE OPERATIONAL READINESS - 1 ROTATING BRUSH AT THE OUTLET SIDE OF THE MACHINE - SEPARATED ARRANGED DUST SUCTION HOSES AND NOZZLES FOR THE SANDING BELT (DM 200 MM) AND THE CLEANING BRUSH (DM 200 MM) - WITH COMPLETE PNEUMATIC CONTROL , INCLUDING AUTOMATIC PRESSURE SWITCH, CONTROL AND MONITORING DEVICES - ALL ELECTRICAL CONTROLS - MAIN SWITCH, FUSES, CONTACTOR CONTROL WITH MOTOR PROTECTION RELAY, DISPLAY DEVICES - VDE - EXECUTION - POWER CONSUMPTION: APPROX. 17 KW -. OPERATING VOLTAGE: 380 V, 50 HZ.
Vendedor: Maschinen-Kaul GmbH & Co.KG
Año de construcción: usado
Ubicación: Land-amtec shrinktunnel-pof-xxxl pro-version<br><br>shrink tunnel for large sized products, pro-version for max. evenly temperature, ideal to be combined with amtec maxishrink w15 4xl pro-version. suitable for polyolefin films. adjustable speed and temperature. - technical specifications: 380v, 24kw | speed: 0-30m/min | temperature: up to 175°c | max. product dimensions (mm): w940xh250 | machine dimensions (mm): l2800xw1460xh1280 | weight (net/gross): ca. 350/400kg.<br><br>our machines are available as sample, exhibition or demonstration machines and available directly from stock/overstock. sometimes also not yet fully finished systems are available that can be finished according to your specifications. deviations from the sample photo are possible. an intermediate sale is reserved. - all machines are available with full warranty. AMTEC SHRINKTUNNEL-POF-XXXL PRO-VERSION

SHRINK TUNNEL FOR LARGE SIZED PRODUCTS, PRO-VERSION FOR MAX. EVENLY TEMPERATURE, IDEAL TO BE COMBINED WITH AMTEC MAXISHRINK W15 4XL PRO-VERSION. SUITABLE FOR POLYOLEFIN FILMS. ADJUSTABLE SPEED AND TEMPERATURE. - TECHNICAL SPECIFICATIONS: 380V, 24KW | SPEED: 0-30M/MIN | TEMPERATURE: UP TO 175°C | MAX. PRODUCT DIMENSIONS (MM): W940XH250 | MACHINE DIMENSIONS (MM): L2800XW1460XH1280 | WEIGHT (NET/GROSS): CA. 350/400KG.

OUR MACHINES ARE AVAILABLE AS SAMPLE, EXHIBITION OR DEMONSTRATION MACHINES AND AVAILABLE DIRECTLY FROM STOCK/OVERSTOCK. SOMETIMES ALSO NOT YET FULLY FINISHED SYSTEMS ARE AVAILABLE THAT CAN BE FINISHED ACCORDING TO YOUR SPECIFICATIONS. DEVIATIONS FROM THE SAMPLE PHOTO ARE POSSIBLE. AN INTERMEDIATE SALE IS RESERVED. - ALL MACHINES ARE AVAILABLE WITH FULL WARRANTY.
Vendedor: BluePack Machines GmbH
Usted no ha encontrado su máquina deseada? enviar consulta a todos los distribuidores (no hay registro necesario)
more GUILLIET types: