172 ofertas

Año de construcción: usado
Ubicación: Land-300 tons tie-bar-less imm built in 2008 with cc 200 control, integrated engel robot erc 33/2-f, crane for mould fixing (2tons), 16 hot chanel, accumulator for fast injection and parallel movements. 2 core puller fix platen, flow meter, transport belt. plastizising screw bimetalic.

technical details	
daylight max	1.300 mm
min. mould hight	400 mm
year of building	2008
working hours	73506
injection pressure	1.616/2.053 bar
injection volumen	511 cm3
nominal capacity of pump motor	45 kw
travel opening	900 mm
screw diameter	55 mm
platen size	1.100 x 1.000 mm
clamping force	3.000 kn 300 TONS TIE-BAR-LESS IMM BUILT IN 2008 WITH CC 200 CONTROL, INTEGRATED ENGEL ROBOT ERC 33/2-F, CRANE FOR MOULD FIXING (2TONS), 16 HOT CHANEL, ACCUMULATOR FOR FAST INJECTION AND PARALLEL MOVEMENTS. 2 CORE PULLER FIX PLATEN, FLOW METER, TRANSPORT BELT. PLASTIZISING SCREW BIMETALIC. TECHNICAL DETAILS DAYLIGHT MAX 1.300 MM MIN. MOULD HIGHT 400 MM YEAR OF BUILDING 2008 WORKING HOURS 73506 INJECTION PRESSURE 1.616/2.053 BAR INJECTION VOLUMEN 511 CM3 NOMINAL CAPACITY OF PUMP MOTOR 45 KW TRAVEL OPENING 900 MM SCREW DIAMETER 55 MM PLATEN SIZE 1.100 X 1.000 MM CLAMPING FORCE 3.000 KN
Vendedor: Udo Krichbaum TRANSITUS, S.L.
Año de construcción: usado
Ubicación: Land-stainless steel, cap. approx. 70 washings/h\r\nworking height 850 mm\r\naccessories: dosimeter STAINLESS STEEL, CAP. APPROX. 70 WASHINGS/H\R\NWORKING HEIGHT 850 MM\R\NACCESSORIES: DOSIMETER
Vendedor: Thünnesen GmbH
Año de construcción: usado
Ubicación: Land-cassette for warehouse, about 1,539 cassettes, cassette length 6, 50 m, 3, 000 kg/kasstte - used -:
 
price on request!
 
manufacturer: fehr
year of construction: 2001
cassettes ges. 1,539 units
specification
1 electrically operated double table long good stack machine, automatically controlled, for the storage and retrieval of for good material, with the help of cassettes
technical data:
capacity 2x3000kg
bottom load table position above ground 700 mm
top load table position above ground 12110 mm
room height 13'450 mm
lifting speed 35 m / min
travel speed 80 m / min
pull-out speed 85 m / min
operating voltage, three-phase 400 v / 50 hz
control voltage 230 v / 50 hz
24 v dc
cassette type internal dimensions (wxhxl) a 520 x 270 x 6500 mm
type b 520 x 520 x 6500 mm
device performance at 100% load 46 ds / h
according to fem based on ub-3000 9.851
pull-out force on the cassette gripper (20% of the payload plus cartridge weight)
 
control automatically arranged using an automatic control over operating terminal, at the camp office
1. 1 double-sided track, length approx 29 m
to hang up on the concrete floor, consisting of:
the two rails of a 55, with the shocks, complete with attachment fittings and the limit stops. the rails are with fade-free special grout under poured.
2. 1 longitudinal-power supply, length approx 29 m, consisting of:
vahle plastic conductor line, with guard, complete with the mounting brackets.
3. 1 long goods stacking devices, consisting of:
camp 2 head straps welded design, with the chassis, this consisting of wã¤lzge controlled from the two engines with shaft mounted gearboxes built-on, as well as the 4 - crane wheels, with leadership roles, running laterally on the road,
2 columns in welded box construction, with the guides for the lifters from material performed st 52.3, screwed on the head straps, including the stiffening frame, as well as a ladder of descent,.
1 pallet truck, consisting of: the steel construction with the necessary rubber buffers for the two hã¶henend positions, the roller bearing support and leadership roles, the double cassette table with glides, the extractor, the centering with side guard rails to complete the box, complete with the runners for the gripper, the drive motors, sprockets, shafts, chains and electrical installation,
controls the horizontal, which â«fachbelegtâ».
as a hoist is used:
1 controlled engine
with intermediate gear (designed according to fem 3 m) and drum includes cords and ball-bearing pulleys; security 12, with double-grooved rope drum, dust-protected bearings drum bearing,
rope pulleys conditions according to din 15020.
4. electrical installation, comprising:
-the special cables, including all required terminal boxes, connecting cables fixed installed on the device
-the flexible power supply in cable caterpillar to the trucks,
-completely wired cabinet incl. contactor and the necessary controls, the mushroom-head pushbutton, which shuts off the main contactor (red mushroom can be rotated), switch with push button, key switch
-the two key selector switches, which are used for the pre-selection of the operating modes â«tip operation/automatic modeâ»,
the limit switches for the limitation of the lifting and moving
-the reciprocal locking of lifting and suspension compared to the ausziehvorâ¬
-direction, the laterally mounted clamping wires to the continuous control of the speed profile
-the profile control, which monitors whether the space between the shelf and device is free,
-the output fuse, which prevents that cassettes in a free space be outsourced,
-excess height control, which prevents a training and storage of high-loaded cartridges,
-the control of tape position on the table,
-the fault indicator in the control panel on the lift truck,
-the operating hour counters for driving and lifting mechanism
displacement measuring systems
the wear-free optical measuring system guarantees maximum service life and precise way capture of the x - and y-coordinates. the way capture of the two gripper through the absolute value encoder is located in the millimetre range. both systems deliver the absolutely correct readings again even after a power failure. thus it takes no movements for repositioning and the device starts working immediately without delay.
driving behavior
driving in the x and y axes is such that at the maximum possible speed infinitely variable over short or long distances optimal speed curves are driven. the behavior of the device dimensions at various distances is taken into account and flows as a control variable with a. the pendulum effect is compensated with counteract the driving curve characteristics,
learning functions
the computer software is so forward-looking that hardly a parameterization of various sizes must be done by the programmer. the software adaptation to different design types of device and storage compartments is done through the learning and self-learning onsite. following learning processes take place during commissioning on site:
-self-learning of the xy-driving behavior
-learning of the gripper behavior
-learning the transfer and recording places of the periphery
self learning the topology of all storage compartments of different arrangement and sizes
operating modes
-jog
the long good stacking device in the direction of travel, the truck and the two pull-out devices can be moved with the control buttons.
-semi automatic (automatic start-up), arranged in the stationary cupboard.
with the hand-held micro terminal, various movements are run separately or in combination automatically:
-driving horizontal
vertical lifting/lowering
-pull cassette
-slide tape
-positioning in front of the nearest
option
pc-cabinet for m fs calculator
execution: wxhxd 600 x 1900 x 600 mm
4-field 17 "monitor field of vision
part of front door for computer unit
integrated keyboard tray
storage compartment with removable rails
socket 100 mm
(ii) peripheral components, including:
1 1 carousel ka-3000 gr gr
for cassettes with rods
technical data:
capacity/capacity 3000 kg
number of pitches 4
conveying speed along 24 m / min
cross conveyor speed 40 m / min
height from top of floor 700 mm
operating voltage 400 v / 50 hz
control voltage 230 v / 50 hz
the cartridge space tracking via the automatic control. the carousel consists in particular of:
outsourcing train, consisting of:
-the steel foot plates and anchors, directly on the ground turned off and integrated into the shelf, suitable for the installation of the required mechanical parts
-the spezialgleitem, as well as the lateral guide
-the gripper mechanism, which contains the tape and transported to the next position positively
the gear motor with chain, the sprocket wheels and the chain guide
cross conveyor belt, comprising;
-two cassette courses, one of them as work provided
-the steel construction incl. foot plates and anchors, placed directly on the floor, suitable for the installation of the required mechanical parts
-the special gliders, as well as the lateral guide
-the querverschiebebalken as a driver for the cassettes
-the drive motor with the required drive elements
-the mechanical preparations for the load cells installation at the workplace
storage car, running such as paging railway
electrical control consisting of:
-the control panel with push buttons for all individual movements, including on/off button and emergency push button
-the position and control switches
-power and control supply
-firmly installed control cabinets with built-in control
-the necessary cables, as well as the internal wiring
the safety light barrier incl. mounting brackets, which perceives the person protection during cartridge movement
 
condition: used, the last maintenance was performed in 2017, shortly after it was mined professionally, so that it can be rebuilt at any time. the company which has degraded the plant could perform the installation.
available: available now
location: nuremberg CASSETTE FOR WAREHOUSE, ABOUT 1,539 CASSETTES, CASSETTE LENGTH 6, 50 M, 3, 000 KG/KASSTTE - USED -: PRICE ON REQUEST! MANUFACTURER: FEHR YEAR OF CONSTRUCTION: 2001 CASSETTES GES. 1,539 UNITS SPECIFICATION 1 ELECTRICALLY OPERATED DOUBLE TABLE LONG GOOD STACK MACHINE, AUTOMATICALLY CONTROLLED, FOR THE STORAGE AND RETRIEVAL OF FOR GOOD MATERIAL, WITH THE HELP OF CASSETTES TECHNICAL DATA: CAPACITY 2X3000KG BOTTOM LOAD TABLE POSITION ABOVE GROUND 700 MM TOP LOAD TABLE POSITION ABOVE GROUND 12110 MM ROOM HEIGHT 13'450 MM LIFTING SPEED 35 M / MIN TRAVEL SPEED 80 M / MIN PULL-OUT SPEED 85 M / MIN OPERATING VOLTAGE, THREE-PHASE 400 V / 50 HZ CONTROL VOLTAGE 230 V / 50 HZ 24 V DC CASSETTE TYPE INTERNAL DIMENSIONS (WXHXL) A 520 X 270 X 6500 MM TYPE B 520 X 520 X 6500 MM DEVICE PERFORMANCE AT 100% LOAD 46 DS / H ACCORDING TO FEM BASED ON UB-3000 9.851 PULL-OUT FORCE ON THE CASSETTE GRIPPER (20% OF THE PAYLOAD PLUS CARTRIDGE WEIGHT) CONTROL AUTOMATICALLY ARRANGED USING AN AUTOMATIC CONTROL OVER OPERATING TERMINAL, AT THE CAMP OFFICE 1. 1 DOUBLE-SIDED TRACK, LENGTH APPROX 29 M TO HANG UP ON THE CONCRETE FLOOR, CONSISTING OF: THE TWO RAILS OF A 55, WITH THE SHOCKS, COMPLETE WITH ATTACHMENT FITTINGS AND THE LIMIT STOPS. THE RAILS ARE WITH FADE-FREE SPECIAL GROUT UNDER POURED. 2. 1 LONGITUDINAL-POWER SUPPLY, LENGTH APPROX 29 M, CONSISTING OF: VAHLE PLASTIC CONDUCTOR LINE, WITH GUARD, COMPLETE WITH THE MOUNTING BRACKETS. 3. 1 LONG GOODS STACKING DEVICES, CONSISTING OF: CAMP 2 HEAD STRAPS WELDED DESIGN, WITH THE CHASSIS, THIS CONSISTING OF WäLZGE CONTROLLED FROM THE TWO ENGINES WITH SHAFT MOUNTED GEARBOXES BUILT-ON, AS WELL AS THE 4 - CRANE WHEELS, WITH LEADERSHIP ROLES, RUNNING LATERALLY ON THE ROAD, 2 COLUMNS IN WELDED BOX CONSTRUCTION, WITH THE GUIDES FOR THE LIFTERS FROM MATERIAL PERFORMED ST 52.3, SCREWED ON THE HEAD STRAPS, INCLUDING THE STIFFENING FRAME, AS WELL AS A LADDER OF DESCENT,. 1 PALLET TRUCK, CONSISTING OF: THE STEEL CONSTRUCTION WITH THE NECESSARY RUBBER BUFFERS FOR THE TWO HöHENEND POSITIONS, THE ROLLER BEARING SUPPORT AND LEADERSHIP ROLES, THE DOUBLE CASSETTE TABLE WITH GLIDES, THE EXTRACTOR, THE CENTERING WITH SIDE GUARD RAILS TO COMPLETE THE BOX, COMPLETE WITH THE RUNNERS FOR THE GRIPPER, THE DRIVE MOTORS, SPROCKETS, SHAFTS, CHAINS AND ELECTRICAL INSTALLATION, CONTROLS THE HORIZONTAL, WHICH «FACHBELEGT». AS A HOIST IS USED: 1 CONTROLLED ENGINE WITH INTERMEDIATE GEAR (DESIGNED ACCORDING TO FEM 3 M) AND DRUM INCLUDES CORDS AND BALL-BEARING PULLEYS; SECURITY 12, WITH DOUBLE-GROOVED ROPE DRUM, DUST-PROTECTED BEARINGS DRUM BEARING, ROPE PULLEYS CONDITIONS ACCORDING TO DIN 15020. 4. ELECTRICAL INSTALLATION, COMPRISING: -THE SPECIAL CABLES, INCLUDING ALL REQUIRED TERMINAL BOXES, CONNECTING CABLES FIXED INSTALLED ON THE DEVICE -THE FLEXIBLE POWER SUPPLY IN CABLE CATERPILLAR TO THE TRUCKS, -COMPLETELY WIRED CABINET INCL. CONTACTOR AND THE NECESSARY CONTROLS, THE MUSHROOM-HEAD PUSHBUTTON, WHICH SHUTS OFF THE MAIN CONTACTOR (RED MUSHROOM CAN BE ROTATED), SWITCH WITH PUSH BUTTON, KEY SWITCH -THE TWO KEY SELECTOR SWITCHES, WHICH ARE USED FOR THE PRE-SELECTION OF THE OPERATING MODES «TIP OPERATION/AUTOMATIC MODE», THE LIMIT SWITCHES FOR THE LIMITATION OF THE LIFTING AND MOVING -THE RECIPROCAL LOCKING OF LIFTING AND SUSPENSION COMPARED TO THE AUSZIEHVOR¬ -DIRECTION, THE LATERALLY MOUNTED CLAMPING WIRES TO THE CONTINUOUS CONTROL OF THE SPEED PROFILE -THE PROFILE CONTROL, WHICH MONITORS WHETHER THE SPACE BETWEEN THE SHELF AND DEVICE IS FREE, -THE OUTPUT FUSE, WHICH PREVENTS THAT CASSETTES IN A FREE SPACE BE OUTSOURCED, -EXCESS HEIGHT CONTROL, WHICH PREVENTS A TRAINING AND STORAGE OF HIGH-LOADED CARTRIDGES, -THE CONTROL OF TAPE POSITION ON THE TABLE, -THE FAULT INDICATOR IN THE CONTROL PANEL ON THE LIFT TRUCK, -THE OPERATING HOUR COUNTERS FOR DRIVING AND LIFTING MECHANISM DISPLACEMENT MEASURING SYSTEMS THE WEAR-FREE OPTICAL MEASURING SYSTEM GUARANTEES MAXIMUM SERVICE LIFE AND PRECISE WAY CAPTURE OF THE X - AND Y-COORDINATES. THE WAY CAPTURE OF THE TWO GRIPPER THROUGH THE ABSOLUTE VALUE ENCODER IS LOCATED IN THE MILLIMETRE RANGE. BOTH SYSTEMS DELIVER THE ABSOLUTELY CORRECT READINGS AGAIN EVEN AFTER A POWER FAILURE. THUS IT TAKES NO MOVEMENTS FOR REPOSITIONING AND THE DEVICE STARTS WORKING IMMEDIATELY WITHOUT DELAY. DRIVING BEHAVIOR DRIVING IN THE X AND Y AXES IS SUCH THAT AT THE MAXIMUM POSSIBLE SPEED INFINITELY VARIABLE OVER SHORT OR LONG DISTANCES OPTIMAL SPEED CURVES ARE DRIVEN. THE BEHAVIOR OF THE DEVICE DIMENSIONS AT VARIOUS DISTANCES IS TAKEN INTO ACCOUNT AND FLOWS AS A CONTROL VARIABLE WITH A. THE PENDULUM EFFECT IS COMPENSATED WITH COUNTERACT THE DRIVING CURVE CHARACTERISTICS, LEARNING FUNCTIONS THE COMPUTER SOFTWARE IS SO FORWARD-LOOKING THAT HARDLY A PARAMETERIZATION OF VARIOUS SIZES MUST BE DONE BY THE PROGRAMMER. THE SOFTWARE ADAPTATION TO DIFFERENT DESIGN TYPES OF DEVICE AND STORAGE COMPARTMENTS IS DONE THROUGH THE LEARNING AND SELF-LEARNING ONSITE. FOLLOWING LEARNING PROCESSES TAKE PLACE DURING COMMISSIONING ON SITE: -SELF-LEARNING OF THE XY-DRIVING BEHAVIOR -LEARNING OF THE GRIPPER BEHAVIOR -LEARNING THE TRANSFER AND RECORDING PLACES OF THE PERIPHERY SELF LEARNING THE TOPOLOGY OF ALL STORAGE COMPARTMENTS OF DIFFERENT ARRANGEMENT AND SIZES OPERATING MODES -JOG THE LONG GOOD STACKING DEVICE IN THE DIRECTION OF TRAVEL, THE TRUCK AND THE TWO PULL-OUT DEVICES CAN BE MOVED WITH THE CONTROL BUTTONS. -SEMI AUTOMATIC (AUTOMATIC START-UP), ARRANGED IN THE STATIONARY CUPBOARD. WITH THE HAND-HELD MICRO TERMINAL, VARIOUS MOVEMENTS ARE RUN SEPARATELY OR IN COMBINATION AUTOMATICALLY: -DRIVING HORIZONTAL VERTICAL LIFTING/LOWERING -PULL CASSETTE -SLIDE TAPE -POSITIONING IN FRONT OF THE NEAREST OPTION PC-CABINET FOR M FS CALCULATOR EXECUTION: WXHXD 600 X 1900 X 600 MM 4-FIELD 17 "MONITOR FIELD OF VISION PART OF FRONT DOOR FOR COMPUTER UNIT INTEGRATED KEYBOARD TRAY STORAGE COMPARTMENT WITH REMOVABLE RAILS SOCKET 100 MM (II) PERIPHERAL COMPONENTS, INCLUDING: 1 1 CAROUSEL KA-3000 GR GR FOR CASSETTES WITH RODS TECHNICAL DATA: CAPACITY/CAPACITY 3000 KG NUMBER OF PITCHES 4 CONVEYING SPEED ALONG 24 M / MIN CROSS CONVEYOR SPEED 40 M / MIN HEIGHT FROM TOP OF FLOOR 700 MM OPERATING VOLTAGE 400 V / 50 HZ CONTROL VOLTAGE 230 V / 50 HZ THE CARTRIDGE SPACE TRACKING VIA THE AUTOMATIC CONTROL. THE CAROUSEL CONSISTS IN PARTICULAR OF: OUTSOURCING TRAIN, CONSISTING OF: -THE STEEL FOOT PLATES AND ANCHORS, DIRECTLY ON THE GROUND TURNED OFF AND INTEGRATED INTO THE SHELF, SUITABLE FOR THE INSTALLATION OF THE REQUIRED MECHANICAL PARTS -THE SPEZIALGLEITEM, AS WELL AS THE LATERAL GUIDE -THE GRIPPER MECHANISM, WHICH CONTAINS THE TAPE AND TRANSPORTED TO THE NEXT POSITION POSITIVELY THE GEAR MOTOR WITH CHAIN, THE SPROCKET WHEELS AND THE CHAIN GUIDE CROSS CONVEYOR BELT, COMPRISING; -TWO CASSETTE COURSES, ONE OF THEM AS WORK PROVIDED -THE STEEL CONSTRUCTION INCL. FOOT PLATES AND ANCHORS, PLACED DIRECTLY ON THE FLOOR, SUITABLE FOR THE INSTALLATION OF THE REQUIRED MECHANICAL PARTS -THE SPECIAL GLIDERS, AS WELL AS THE LATERAL GUIDE -THE QUERVERSCHIEBEBALKEN AS A DRIVER FOR THE CASSETTES -THE DRIVE MOTOR WITH THE REQUIRED DRIVE ELEMENTS -THE MECHANICAL PREPARATIONS FOR THE LOAD CELLS INSTALLATION AT THE WORKPLACE STORAGE CAR, RUNNING SUCH AS PAGING RAILWAY ELECTRICAL CONTROL CONSISTING OF: -THE CONTROL PANEL WITH PUSH BUTTONS FOR ALL INDIVIDUAL MOVEMENTS, INCLUDING ON/OFF BUTTON AND EMERGENCY PUSH BUTTON -THE POSITION AND CONTROL SWITCHES -POWER AND CONTROL SUPPLY -FIRMLY INSTALLED CONTROL CABINETS WITH BUILT-IN CONTROL -THE NECESSARY CABLES, AS WELL AS THE INTERNAL WIRING THE SAFETY LIGHT BARRIER INCL. MOUNTING BRACKETS, WHICH PERCEIVES THE PERSON PROTECTION DURING CARTRIDGE MOVEMENT CONDITION: USED, THE LAST MAINTENANCE WAS PERFORMED IN 2017, SHORTLY AFTER IT WAS MINED PROFESSIONALLY, SO THAT IT CAN BE REBUILT AT ANY TIME. THE COMPANY WHICH HAS DEGRADED THE PLANT COULD PERFORM THE INSTALLATION. AVAILABLE: AVAILABLE NOW LOCATION: NUREMBERG
Vendedor: Alexander von Westernhagen
Año de construcción: usado
Precio: used machinery auction RESALE 1.500 €
Ubicación: Land-weight approx.: 3000 kg<br/>running hours: 8132 h<br/>loading capacity: 1,6 t<br/>lifting height: 3 f 7500 m<br/>fork length of fork lift: 1200 - 2000 m<br/>overall height: 3200 m<br/>dimensions (l x w x h) approx.: 1800 x 1200 x 3200 mm<br/>description: bt rr-b 2 electric forklift<br> - serial no.: 726287<br> - drive: 48 v<br> - set of tyres: vulcolan<br> - battery and charger: 48 v<br> - fork length: 1200 mm, manual until 2000 mm<br> - with altimeter display and lateral shift WEIGHT APPROX.: 3000 KG
RUNNING HOURS: 8132 H
LOADING CAPACITY: 1,6 T
LIFTING HEIGHT: 3 F 7500 M
FORK LENGTH OF FORK LIFT: 1200 - 2000 M
OVERALL HEIGHT: 3200 M
DIMENSIONS (L X W X H) APPROX.: 1800 X 1200 X 3200 MM
DESCRIPTION: BT RR-B 2 ELECTRIC FORKLIFT
- SERIAL NO.: 726287
- DRIVE: 48 V
- SET OF TYRES: VULCOLAN
- BATTERY AND CHARGER: 48 V
- FORK LENGTH: 1200 MM, MANUAL UNTIL 2000 MM
- WITH ALTIMETER DISPLAY AND LATERAL SHIFT
Vendedor: Surplex GmbH
Año de construcción: usado
Precio: 10.000 
Ubicación: Land-automatic labelling machine eca
is designed for sticking one label on cylindrical packaging, for example. bottles, cans, jars, etc.
gluing can be done on the part of or around the perimeter. labeling machine works with paper labels.
the glue is applied stripes on the entire length of the label. the machine uses mainly stainless materials.
labelling machine eca is intended to automatically place a single paper labels on cylindrical or square packaging such as bottles, jars, cans, plastic, etc., in a wide range of dimensions . it is made of elements made of stainless steel, plastic and die casting secured against corrosion, va steel coatings and lakierniczymi. transporter, covers and clutch parts are made of stainless steel (grade 1h18n9t).

bej9teavxo
accuracy (nierównoleg?o??) bonding of labels is 1 mm to 100 mm in length.

overall dimensions: • length-2700 mm; • width-1.000 mm; • height-1.320 mm.
technical data: •
• max. efficiency-6.000 op/h.;
• weight-450 kg;
• has the adhesive heating;
• power supply-220/380 v-10 a;
• the dimensions of the label-max. length – 230 mm; max.
height-200 mm;
• drive-electric motor-1.5 kw;
1.420 u/min
; • diameter-min. 50 mm; max: 100 mm;
• the scope of the bonding-the height of the glue (minimum 2 mm from the base to the bottom edge of the label) (max. 200 mm from the base to the top edge of the label)-precision bonding (nierównoleg?a to the base up to 1 mm/100 mm length of the labels) AUTOMATIC LABELLING MACHINE ECA IS DESIGNED FOR STICKING ONE LABEL ON CYLINDRICAL PACKAGING, FOR EXAMPLE. BOTTLES, CANS, JARS, ETC. GLUING CAN BE DONE ON THE PART OF OR AROUND THE PERIMETER. LABELING MACHINE WORKS WITH PAPER LABELS. THE GLUE IS APPLIED STRIPES ON THE ENTIRE LENGTH OF THE LABEL. THE MACHINE USES MAINLY STAINLESS MATERIALS. LABELLING MACHINE ECA IS INTENDED TO AUTOMATICALLY PLACE A SINGLE PAPER LABELS ON CYLINDRICAL OR SQUARE PACKAGING SUCH AS BOTTLES, JARS, CANS, PLASTIC, ETC., IN A WIDE RANGE OF DIMENSIONS . IT IS MADE OF ELEMENTS MADE OF STAINLESS STEEL, PLASTIC AND DIE CASTING SECURED AGAINST CORROSION, VA STEEL COATINGS AND LAKIERNICZYMI. TRANSPORTER, COVERS AND CLUTCH PARTS ARE MADE OF STAINLESS STEEL (GRADE 1H18N9T). BEJ9TEAVXO ACCURACY (NIERóWNOLEG?O??) BONDING OF LABELS IS 1 MM TO 100 MM IN LENGTH. OVERALL DIMENSIONS: • LENGTH-2700 MM; • WIDTH-1.000 MM; • HEIGHT-1.320 MM. TECHNICAL DATA: • • MAX. EFFICIENCY-6.000 OP/H.; • WEIGHT-450 KG; • HAS THE ADHESIVE HEATING; • POWER SUPPLY-220/380 V-10 A; • THE DIMENSIONS OF THE LABEL-MAX. LENGTH – 230 MM; MAX. HEIGHT-200 MM; • DRIVE-ELECTRIC MOTOR-1.5 KW; 1.420 U/MIN ; • DIAMETER-MIN. 50 MM; MAX: 100 MM; • THE SCOPE OF THE BONDING-THE HEIGHT OF THE GLUE (MINIMUM 2 MM FROM THE BASE TO THE BOTTOM EDGE OF THE LABEL) (MAX. 200 MM FROM THE BASE TO THE TOP EDGE OF THE LABEL)-PRECISION BONDING (NIERóWNOLEG?A TO THE BASE UP TO 1 MM/100 MM LENGTH OF THE LABELS)
Vendedor: Machine-For-Sale.com
Año de construcción: usado
Ubicación: Land-veneer jointing guillotine, hydraulic\r\nbrand: casati\r\ntype: to/cc 3600\r\nnew machine\r\n\r\ntechnical data:\r\n\r\ncutting length: 3.600 mm\r\ndaylight opening of the clamping beam: 100 mm\r\nmax. rear feed width 800 mm\r\nmin. rear feed width 25 mm\r\nhydraulic unit motor power 10 ps\r\nrear feed motor power 0,5 ps\r\n\r\nequipped with:\r\n- motordriven feed of the back fence\r\n- cutting edge light\r\n- millimeter counter\r\n- manual and automatic working cycle. the operator can choose between: \r\nmanual working cycle (separated controls for each phase of the working cycle) or automatic working cycle (one only push-button control for the whole cycle)\r\n- hydraulic control valve of speed and pressure of knife beam and clamping beam\r\n- central system of lubrication\r\n- knife made with special steel\r\n- angular fence\r\n- photocells and guards as per ec rules\r\n\r\noptions for an extra charge\r\n- photo cells and guards per ec rules\r\n- absolute electron. read-out + partial read-out\r\n\r\nmachine is also available in cutting length:\r\n1.300, 1.450 , 2.600, 2.800, 3.200, 4.000, 4.400 mm\r\n VENEER JOINTING GUILLOTINE, HYDRAULIC\R\NBRAND: CASATI\R\NTYPE: TO/CC 3600\R\NNEW MACHINE\R\N\R\NTECHNICAL DATA:\R\N\R\NCUTTING LENGTH: 3.600 MM\R\NDAYLIGHT OPENING OF THE CLAMPING BEAM: 100 MM\R\NMAX. REAR FEED WIDTH 800 MM\R\NMIN. REAR FEED WIDTH 25 MM\R\NHYDRAULIC UNIT MOTOR POWER 10 PS\R\NREAR FEED MOTOR POWER 0,5 PS\R\N\R\NEQUIPPED WITH:\R\N- MOTORDRIVEN FEED OF THE BACK FENCE\R\N- CUTTING EDGE LIGHT\R\N- MILLIMETER COUNTER\R\N- MANUAL AND AUTOMATIC WORKING CYCLE. THE OPERATOR CAN CHOOSE BETWEEN: \R\NMANUAL WORKING CYCLE (SEPARATED CONTROLS FOR EACH PHASE OF THE WORKING CYCLE) OR AUTOMATIC WORKING CYCLE (ONE ONLY PUSH-BUTTON CONTROL FOR THE WHOLE CYCLE)\R\N- HYDRAULIC CONTROL VALVE OF SPEED AND PRESSURE OF KNIFE BEAM AND CLAMPING BEAM\R\N- CENTRAL SYSTEM OF LUBRICATION\R\N- KNIFE MADE WITH SPECIAL STEEL\R\N- ANGULAR FENCE\R\N- PHOTOCELLS AND GUARDS AS PER EC RULES\R\N\R\NOPTIONS FOR AN EXTRA CHARGE\R\N- PHOTO CELLS AND GUARDS PER EC RULES\R\N- ABSOLUTE ELECTRON. READ-OUT + PARTIAL READ-OUT\R\N\R\NMACHINE IS ALSO AVAILABLE IN CUTTING LENGTH:\R\N1.300, 1.450 , 2.600, 2.800, 3.200, 4.000, 4.400 MM\R\N
Vendedor: Wehrmann Holzbearbeitungsmaschinen GmbH & Co.KG
Año de construcción: usado
Ubicación: Land-code: 0560
brand: marzani macchine
model: multicenter tipo fa 1200 dm - ce standard 

cnc working center  (drilling/screwing -milling) for doors and window frames , doors and panels - ce standard
for the execution of locks, counterplates, pawls, drilling, milling, routing, blinds, insertion of anuba hinges
useful longitudinal stroke axis x 3200 mm

milling head:
useful y-axis  transversal stroke with   milling  cutter  at 90 °   1200 mm
useful y-axis  transversal  stroke with  milling cutter at  180 °   900 mm
useful height of  z -axis 110 mm
motor kw 8 - rpm 12000/18000 

horizontal milling head:
engine kw 3,35

drilling/screwing head:
useful  transversla stroke  axis (t) 100 mm
max useful  height axis  (v) 110 mm
head inclination from -7 to + 90 °
motor kw 1,5 - rpm 1400 

composition:
drilling/screwing  head (drilling  screwing ) for the execution of all the drilling screwing workings 
 horizontal electrospindle kw 3.35 for milling and drilling operations
vertical electrospindle kw 8 iso 30 pneumatic with 180 ° overturning for milling and drilling  operations
8-positions tool change
double support surface with pneumatic locking
2 side piece clamping vices
2 disappearing references
vacuum pump 80 m3 for  piece holding
12 suction cups for piece locking
electric pump for automatic lubrication
control panel
computer: windows operating system - pentium 2 processor - color monitor - ram 64 memory
perimeter security barrier
installed power 20 kw
compressed air pressure bar 7
n ° 2 suction inlets diameter 80 mm
overall dimensions mounted machine: mm 5200 x 6200 x 2300 h



 CODE: 0560 BRAND: MARZANI MACCHINE MODEL: MULTICENTER TIPO FA 1200 DM - CE STANDARD CNC WORKING CENTER (DRILLING/SCREWING -MILLING) FOR DOORS AND WINDOW FRAMES , DOORS AND PANELS - CE STANDARD FOR THE EXECUTION OF LOCKS, COUNTERPLATES, PAWLS, DRILLING, MILLING, ROUTING, BLINDS, INSERTION OF ANUBA HINGES USEFUL LONGITUDINAL STROKE AXIS X 3200 MM MILLING HEAD: USEFUL Y-AXIS TRANSVERSAL STROKE WITH MILLING CUTTER AT 90 ° 1200 MM USEFUL Y-AXIS TRANSVERSAL STROKE WITH MILLING CUTTER AT 180 ° 900 MM USEFUL HEIGHT OF Z -AXIS 110 MM MOTOR KW 8 - RPM 12000/18000 HORIZONTAL MILLING HEAD: ENGINE KW 3,35 DRILLING/SCREWING HEAD: USEFUL TRANSVERSLA STROKE AXIS (T) 100 MM MAX USEFUL HEIGHT AXIS (V) 110 MM HEAD INCLINATION FROM -7 TO + 90 ° MOTOR KW 1,5 - RPM 1400 COMPOSITION: DRILLING/SCREWING HEAD (DRILLING SCREWING ) FOR THE EXECUTION OF ALL THE DRILLING SCREWING WORKINGS HORIZONTAL ELECTROSPINDLE KW 3.35 FOR MILLING AND DRILLING OPERATIONS VERTICAL ELECTROSPINDLE KW 8 ISO 30 PNEUMATIC WITH 180 ° OVERTURNING FOR MILLING AND DRILLING OPERATIONS 8-POSITIONS TOOL CHANGE DOUBLE SUPPORT SURFACE WITH PNEUMATIC LOCKING 2 SIDE PIECE CLAMPING VICES 2 DISAPPEARING REFERENCES VACUUM PUMP 80 M3 FOR PIECE HOLDING 12 SUCTION CUPS FOR PIECE LOCKING ELECTRIC PUMP FOR AUTOMATIC LUBRICATION CONTROL PANEL COMPUTER: WINDOWS OPERATING SYSTEM - PENTIUM 2 PROCESSOR - COLOR MONITOR - RAM 64 MEMORY PERIMETER SECURITY BARRIER INSTALLED POWER 20 KW COMPRESSED AIR PRESSURE BAR 7 N ° 2 SUCTION INLETS DIAMETER 80 MM OVERALL DIMENSIONS MOUNTED MACHINE: MM 5200 X 6200 X 2300 H
Vendedor: TOMESANI Srl
Año de construcción: usado
Precio: used machinery auction RESALE 500 €
Ubicación: Land-weight approx.: 40 kg<br/>dimensions (l x w x h) approx.: 500 x 600 x 1200 mm<br/>description: serial no. 1 k 004201, measuring range 600 mm, incl. accessories WEIGHT APPROX.: 40 KG
DIMENSIONS (L X W X H) APPROX.: 500 X 600 X 1200 MM
DESCRIPTION: SERIAL NO. 1 K 004201, MEASURING RANGE 600 MM, INCL. ACCESSORIES
Vendedor: Surplex GmbH
Año de construcción: usado
Ubicación: Land-300 tons tie-bar-less imm built in 2008 with cc 200 control, integrated engel robot erc 33/2-f, crane for mould fixing (2tons), 16 hot chanel, accumulator for fast injection and parallel movements. 2 core puller fix platen, flow meter, transport belt. plastizising screw bimetalic.

description

   	
technical details	
daylight max	1.300 mm
min. mould hight	400 mm
year of building	2008
working hours	73506
injection pressure	1.616/2.053 bar
injection volumen	511 cm3
nominal capacity of pump motor	45 kw
travel opening	900 mm
screw diameter	55 mm
platen size	1.100 x 1.000 mm
clamping force	3.000 kn 300 TONS TIE-BAR-LESS IMM BUILT IN 2008 WITH CC 200 CONTROL, INTEGRATED ENGEL ROBOT ERC 33/2-F, CRANE FOR MOULD FIXING (2TONS), 16 HOT CHANEL, ACCUMULATOR FOR FAST INJECTION AND PARALLEL MOVEMENTS. 2 CORE PULLER FIX PLATEN, FLOW METER, TRANSPORT BELT. PLASTIZISING SCREW BIMETALIC. DESCRIPTION TECHNICAL DETAILS DAYLIGHT MAX 1.300 MM MIN. MOULD HIGHT 400 MM YEAR OF BUILDING 2008 WORKING HOURS 73506 INJECTION PRESSURE 1.616/2.053 BAR INJECTION VOLUMEN 511 CM3 NOMINAL CAPACITY OF PUMP MOTOR 45 KW TRAVEL OPENING 900 MM SCREW DIAMETER 55 MM PLATEN SIZE 1.100 X 1.000 MM CLAMPING FORCE 3.000 KN
Vendedor: Udo Krichbaum TRANSITUS, S.L.
Año de construcción: usado
Precio: used machinery auction RESALE 400 €
Ubicación: Land-weight approx.: 30 kg<br/>dimensions (l x w x h) approx.: 500 x 400 x 800 mm<br/>description: serial no. 5 m 007111, measuring range 515 mm, operating range from 0 up to 670 mm, incl. matrix printer and several accessories WEIGHT APPROX.: 30 KG
DIMENSIONS (L X W X H) APPROX.: 500 X 400 X 800 MM
DESCRIPTION: SERIAL NO. 5 M 007111, MEASURING RANGE 515 MM, OPERATING RANGE FROM 0 UP TO 670 MM, INCL. MATRIX PRINTER AND SEVERAL ACCESSORIES
Vendedor: Surplex GmbH
Año de construcción: usado
Ubicación: Land-machine specification

year: 2001 
control unit: unilog 9000c 
robot: unirob r15 

injection unit: .../5400
screw diameter: 85 mm 
injection pressure: 1612 bar 
injection volume: 2856 ccm 
shot capacity: 2600 g 

clamping unit: hm 6500/...
clamping force: 650 t 
platen size: 1400 x 1400 mm 
distance between tie bars: 1000 x 1000 mm 
mould height: 600...1000 mm 
opening storke: 1000 mm 
max.daylight: 2000 mm 
ejector stroke: 250 mm 
drive power of the hydraulic pump: 74 kw 
cylinder heating power: 56,8 kw 

general information:
delivery time: now 
machine dimensions(m) lxwxh: 9,73 x 2,19 x 2,56 m 
weight: 41000 kg 

equipment:
- bimetallic barrel
- 2 x pneumatic valve
- 2 x core pull
- increased oil cooler
- with conveyor belt
- robot interface as per euromap 12 MACHINE SPECIFICATION YEAR: 2001 CONTROL UNIT: UNILOG 9000C ROBOT: UNIROB R15 INJECTION UNIT: .../5400 SCREW DIAMETER: 85 MM INJECTION PRESSURE: 1612 BAR INJECTION VOLUME: 2856 CCM SHOT CAPACITY: 2600 G CLAMPING UNIT: HM 6500/... CLAMPING FORCE: 650 T PLATEN SIZE: 1400 X 1400 MM DISTANCE BETWEEN TIE BARS: 1000 X 1000 MM MOULD HEIGHT: 600...1000 MM OPENING STORKE: 1000 MM MAX.DAYLIGHT: 2000 MM EJECTOR STROKE: 250 MM DRIVE POWER OF THE HYDRAULIC PUMP: 74 KW CYLINDER HEATING POWER: 56,8 KW GENERAL INFORMATION: DELIVERY TIME: NOW MACHINE DIMENSIONS(M) LXWXH: 9,73 X 2,19 X 2,56 M WEIGHT: 41000 KG EQUIPMENT: - BIMETALLIC BARREL - 2 X PNEUMATIC VALVE - 2 X CORE PULL - INCREASED OIL COOLER - WITH CONVEYOR BELT - ROBOT INTERFACE AS PER EUROMAP 12
Vendedor: EuropNet GmbH
Año de construcción: usado
Ubicación: Land-internal diameter:250 mm<br/>grinding depth: mm<br/>swing diameter:455 mm<br/>workpiece length - max.:1200 mm<br/>table rotating:-4/+8 °<br/>table speeds:0-4000 mm/min<br/>max. workpiece weight:80 kg<br/>workhead - center taper:5 mk<br/>rotation speed of workhead :0 - 400 1/min<br/>workhead motor:4 kw<br/>3-jaw chuck:250 (selbstschließend) mm<br/>grinding motor:4 kw<br/>coolant pump:2,2 kw<br/>weight approx.:2,4 t<br/>machine dimensions:3200 x 2100 mm<br/>cnc controller:siemens 840 d oder sps von siemens <br/>servo motors: <br/>autom. sensing device for grinding wheel:option <br/>: <br/>linear scales and ballscrew:in allen achsen <br/>grinding wheel dresser: <br/>: <br/>fully enclosed: <br/>: <br/>technical documentation in german language: <br/>ce-design: <br/>signal lamp: <br/>face grinding attachement:durchmesser 125 mm<br/>clamping chuck:250 (selbstschließend), 1 satz harte backen, 1 satz weiche backen, 1 satz innen mm<br/>: <br/>magnetic and paper filter : <br/>levellig elements: <br/>frequency control main spindel engine:für die innenschleifeinrichtung <br/>internal grinding spindle:rpm 28.000, diam. 60 mm. min. diam. cap. 25 mm. x bohrung 50 mm, max. diam. cap. 100 mm. x bohrung 115 mm . <br/>internal grinding spindle:rpm 10.000, diam. 100 mm, min. diam. cap. 50 mm x bohrung 100 mm, max.diam. cap. 250 mm xbohrung 220 mm <br/>fixed steady rests:10-100 mm, 100-170 mm <br/><br/> performance and precision degree   robbi grinding machines are according to the international precision normes iso 2433. the table movement linearity is guaranteed by a max. deviation of  0,002 mm/mt.  the obtainable grinding roundness is :  0,4m (**)  (**)  for a test workpiece ground in our factory during machine testing        the cnc controls :  wheel head movement  (axis x) longitudinal table movement  (axis z) work head spindle rotation speed    the available programs permit the programming of the following grinding cycles  plunge  cylindrical pass   cylindrical pass with interpolation between table and wheel movement to grind taper workpieces radius   the software for the workpiece grinding operation is very simple and intuitive.   to facilitate the programming the software is equipped with an exemplifying graphics, to input the data for each parameter.      the software, has been specially studied, so as to permit also non specialised operators to programme without any problems complex workpieces.   when the workpiece grinding programme has been completed the cnc will automatically make up a summary list, where only the geometric parameters are evidenced.     this list permits with a  glance to verify the complete programme;  this operation is very helpful to verify eventual input data errors or to check rapidly a workpiece programme when reloaded from the file.        while the programme is in execution, it is possible to intervene and modify in real time the technologic parameters, such as:  increments, dwell inversion times, sparkout passes.   also, it is possible to intervene with the jog handwheel.      the grinding machine is composed of :    base  structure in normalised and stabilised cast iron with large ground guides.    the lubrication plant supplies a constant oil flow distributed over the complete length of the guides.    in the middle of the base, there is positioned the ball screw  for the table longitudinal movement.    on all the lower part of the perimeter are situated the recesses for machine levelling.  considering the base structure, usually a foundation is not required.    table   the table is manufactured in two parts, both are in normalised and stabilised cast iron.     the lower  part is composed of wide guides which are ground and accurately hand scrapped, for a better sliding.       the upper part, is swivelable in the two directions, suitable for grinding tapered workpieces.    it includes  a micrometric device with centesimal dial gauge for taper control.       workhead  the structure in normalised, stabilised and well ribbed cast iron, allows to support the workpiece weight and the force generated by the grinding operation.      the spindle rotates on high precision ball bearings, guaranteeing restricted tolerance and maximum rigidity in the working.      the spindle rotation is by means of a three phase motor with variable speed controlled by an inverter.  internal grinding spindle carriage  the structure is composed of a carriage, where the internal grinding spindle is located.    the working feed, is obtained by a re-circulating ball screw and preloaded nut.    the screw movement is assured by a brushless motor.       the incremental optic rule guarantees a wheelhead positioning precision of 0,001 mm.   internal grinding spindle  as there are many and various types of internal grinding spindles, according to the diameters and lengths that need to be ground, the machine is supplied without an internal grinding spindle, so that the customer may select which type is more suitable for his job.      the machine is manufactured standard with a belt transmission suitable for diam. mm. 60, diam. mm. 80 and diam. mm. 100 internal grinding spindles.      on request,  high frequency spindles may be assembled.   wheelhead  for face grinding the structure is composed of a carriage, where the face grinding device is located.    the positioning is obtained by an hydraulic cylinder.   the diamond dressing device is assembled on the face grinding device casing.   manual feed handwheels  electronic type, with double selection of the increments division 0.1 - 0.01 and 0.001 mm.  for wheelhead and table movements.     diamond dresser  the internal diamond dressing device is very strong and is positioned on the table.     it starts  hydraulically, when the dressing operation is selected, by the operator.     the dressing operation may be carried out manually or in automatic cycle.    equipment and electrical plant  in a cooled cabinet, separate from the machine.      hydraulic plant   the hydraulic power pack, is separate from the machine and activates the hydraulic diamond dresser and face grinding device.       lubrication plant the lubrication power pack, is separate from the machine and supplies continuous oil to the wheelhead guides.   the recovered oil is filtered and then resent to the power pack.     the re-circulating ball screw nut for the working feed, is grease lubricated.           coolant plant  large capacity tank for the coolant water, complete with electric equipment.       equipped with coolant magnet cleaner  and coolant paper roll cleaner.       protections  for the protection of the operator all movable parts are covered with suitable guards.     precisely: protection casing for belts, protection casing for grinding wheel and bellows for guides.   the machine is completely closed and the front protection is a sheet sliding doors with poly-carbonate shields.   a safety device, does not permit the automatic cycle to start if the front sliding doors are open.   INTERNAL DIAMETER:250 MM
GRINDING DEPTH: MM
SWING DIAMETER:455 MM
WORKPIECE LENGTH - MAX.:1200 MM
TABLE ROTATING:-4/+8 °
TABLE SPEEDS:0-4000 MM/MIN
MAX. WORKPIECE WEIGHT:80 KG
WORKHEAD - CENTER TAPER:5 MK
ROTATION SPEED OF WORKHEAD :0 - 400 1/MIN
WORKHEAD MOTOR:4 KW
3-JAW CHUCK:250 (SELBSTSCHLIEßEND) MM
GRINDING MOTOR:4 KW
COOLANT PUMP:2,2 KW
WEIGHT APPROX.:2,4 T
MACHINE DIMENSIONS:3200 X 2100 MM
CNC CONTROLLER:SIEMENS 840 D ODER SPS VON SIEMENS
SERVO MOTORS:
AUTOM. SENSING DEVICE FOR GRINDING WHEEL:OPTION
:
LINEAR SCALES AND BALLSCREW:IN ALLEN ACHSEN
GRINDING WHEEL DRESSER:
:
FULLY ENCLOSED:
:
TECHNICAL DOCUMENTATION IN GERMAN LANGUAGE:
CE-DESIGN:
SIGNAL LAMP:
FACE GRINDING ATTACHEMENT:DURCHMESSER 125 MM
CLAMPING CHUCK:250 (SELBSTSCHLIEßEND), 1 SATZ HARTE BACKEN, 1 SATZ WEICHE BACKEN, 1 SATZ INNEN MM
:
MAGNETIC AND PAPER FILTER :
LEVELLIG ELEMENTS:
FREQUENCY CONTROL MAIN SPINDEL ENGINE:FüR DIE INNENSCHLEIFEINRICHTUNG
INTERNAL GRINDING SPINDLE:RPM 28.000, DIAM. 60 MM. MIN. DIAM. CAP. 25 MM. X BOHRUNG 50 MM, MAX. DIAM. CAP. 100 MM. X BOHRUNG 115 MM .
INTERNAL GRINDING SPINDLE:RPM 10.000, DIAM. 100 MM, MIN. DIAM. CAP. 50 MM X BOHRUNG 100 MM, MAX.DIAM. CAP. 250 MM XBOHRUNG 220 MM
FIXED STEADY RESTS:10-100 MM, 100-170 MM

PERFORMANCE AND PRECISION DEGREE ROBBI GRINDING MACHINES ARE ACCORDING TO THE INTERNATIONAL PRECISION NORMES ISO 2433. THE TABLE MOVEMENT LINEARITY IS GUARANTEED BY A MAX. DEVIATION OF 0,002 MM/MT. THE OBTAINABLE GRINDING ROUNDNESS IS : 0,4M (**) (**) FOR A TEST WORKPIECE GROUND IN OUR FACTORY DURING MACHINE TESTING THE CNC CONTROLS : WHEEL HEAD MOVEMENT (AXIS X) LONGITUDINAL TABLE MOVEMENT (AXIS Z) WORK HEAD SPINDLE ROTATION SPEED THE AVAILABLE PROGRAMS PERMIT THE PROGRAMMING OF THE FOLLOWING GRINDING CYCLES PLUNGE CYLINDRICAL PASS CYLINDRICAL PASS WITH INTERPOLATION BETWEEN TABLE AND WHEEL MOVEMENT TO GRIND TAPER WORKPIECES RADIUS THE SOFTWARE FOR THE WORKPIECE GRINDING OPERATION IS VERY SIMPLE AND INTUITIVE. TO FACILITATE THE PROGRAMMING THE SOFTWARE IS EQUIPPED WITH AN EXEMPLIFYING GRAPHICS, TO INPUT THE DATA FOR EACH PARAMETER. THE SOFTWARE, HAS BEEN SPECIALLY STUDIED, SO AS TO PERMIT ALSO NON SPECIALISED OPERATORS TO PROGRAMME WITHOUT ANY PROBLEMS COMPLEX WORKPIECES. WHEN THE WORKPIECE GRINDING PROGRAMME HAS BEEN COMPLETED THE CNC WILL AUTOMATICALLY MAKE UP A SUMMARY LIST, WHERE ONLY THE GEOMETRIC PARAMETERS ARE EVIDENCED. THIS LIST PERMITS WITH A GLANCE TO VERIFY THE COMPLETE PROGRAMME; THIS OPERATION IS VERY HELPFUL TO VERIFY EVENTUAL INPUT DATA ERRORS OR TO CHECK RAPIDLY A WORKPIECE PROGRAMME WHEN RELOADED FROM THE FILE. WHILE THE PROGRAMME IS IN EXECUTION, IT IS POSSIBLE TO INTERVENE AND MODIFY IN REAL TIME THE TECHNOLOGIC PARAMETERS, SUCH AS: INCREMENTS, DWELL INVERSION TIMES, SPARKOUT PASSES. ALSO, IT IS POSSIBLE TO INTERVENE WITH THE JOG HANDWHEEL. THE GRINDING MACHINE IS COMPOSED OF : BASE STRUCTURE IN NORMALISED AND STABILISED CAST IRON WITH LARGE GROUND GUIDES. THE LUBRICATION PLANT SUPPLIES A CONSTANT OIL FLOW DISTRIBUTED OVER THE COMPLETE LENGTH OF THE GUIDES. IN THE MIDDLE OF THE BASE, THERE IS POSITIONED THE BALL SCREW FOR THE TABLE LONGITUDINAL MOVEMENT. ON ALL THE LOWER PART OF THE PERIMETER ARE SITUATED THE RECESSES FOR MACHINE LEVELLING. CONSIDERING THE BASE STRUCTURE, USUALLY A FOUNDATION IS NOT REQUIRED. TABLE THE TABLE IS MANUFACTURED IN TWO PARTS, BOTH ARE IN NORMALISED AND STABILISED CAST IRON. THE LOWER PART IS COMPOSED OF WIDE GUIDES WHICH ARE GROUND AND ACCURATELY HAND SCRAPPED, FOR A BETTER SLIDING. THE UPPER PART, IS SWIVELABLE IN THE TWO DIRECTIONS, SUITABLE FOR GRINDING TAPERED WORKPIECES. IT INCLUDES A MICROMETRIC DEVICE WITH CENTESIMAL DIAL GAUGE FOR TAPER CONTROL. WORKHEAD THE STRUCTURE IN NORMALISED, STABILISED AND WELL RIBBED CAST IRON, ALLOWS TO SUPPORT THE WORKPIECE WEIGHT AND THE FORCE GENERATED BY THE GRINDING OPERATION. THE SPINDLE ROTATES ON HIGH PRECISION BALL BEARINGS, GUARANTEEING RESTRICTED TOLERANCE AND MAXIMUM RIGIDITY IN THE WORKING. THE SPINDLE ROTATION IS BY MEANS OF A THREE PHASE MOTOR WITH VARIABLE SPEED CONTROLLED BY AN INVERTER. INTERNAL GRINDING SPINDLE CARRIAGE THE STRUCTURE IS COMPOSED OF A CARRIAGE, WHERE THE INTERNAL GRINDING SPINDLE IS LOCATED. THE WORKING FEED, IS OBTAINED BY A RE-CIRCULATING BALL SCREW AND PRELOADED NUT. THE SCREW MOVEMENT IS ASSURED BY A BRUSHLESS MOTOR. THE INCREMENTAL OPTIC RULE GUARANTEES A WHEELHEAD POSITIONING PRECISION OF 0,001 MM. INTERNAL GRINDING SPINDLE AS THERE ARE MANY AND VARIOUS TYPES OF INTERNAL GRINDING SPINDLES, ACCORDING TO THE DIAMETERS AND LENGTHS THAT NEED TO BE GROUND, THE MACHINE IS SUPPLIED WITHOUT AN INTERNAL GRINDING SPINDLE, SO THAT THE CUSTOMER MAY SELECT WHICH TYPE IS MORE SUITABLE FOR HIS JOB. THE MACHINE IS MANUFACTURED STANDARD WITH A BELT TRANSMISSION SUITABLE FOR DIAM. MM. 60, DIAM. MM. 80 AND DIAM. MM. 100 INTERNAL GRINDING SPINDLES. ON REQUEST, HIGH FREQUENCY SPINDLES MAY BE ASSEMBLED. WHEELHEAD FOR FACE GRINDING THE STRUCTURE IS COMPOSED OF A CARRIAGE, WHERE THE FACE GRINDING DEVICE IS LOCATED. THE POSITIONING IS OBTAINED BY AN HYDRAULIC CYLINDER. THE DIAMOND DRESSING DEVICE IS ASSEMBLED ON THE FACE GRINDING DEVICE CASING. MANUAL FEED HANDWHEELS ELECTRONIC TYPE, WITH DOUBLE SELECTION OF THE INCREMENTS DIVISION 0.1 - 0.01 AND 0.001 MM. FOR WHEELHEAD AND TABLE MOVEMENTS. DIAMOND DRESSER THE INTERNAL DIAMOND DRESSING DEVICE IS VERY STRONG AND IS POSITIONED ON THE TABLE. IT STARTS HYDRAULICALLY, WHEN THE DRESSING OPERATION IS SELECTED, BY THE OPERATOR. THE DRESSING OPERATION MAY BE CARRIED OUT MANUALLY OR IN AUTOMATIC CYCLE. EQUIPMENT AND ELECTRICAL PLANT IN A COOLED CABINET, SEPARATE FROM THE MACHINE. HYDRAULIC PLANT THE HYDRAULIC POWER PACK, IS SEPARATE FROM THE MACHINE AND ACTIVATES THE HYDRAULIC DIAMOND DRESSER AND FACE GRINDING DEVICE. LUBRICATION PLANT THE LUBRICATION POWER PACK, IS SEPARATE FROM THE MACHINE AND SUPPLIES CONTINUOUS OIL TO THE WHEELHEAD GUIDES. THE RECOVERED OIL IS FILTERED AND THEN RESENT TO THE POWER PACK. THE RE-CIRCULATING BALL SCREW NUT FOR THE WORKING FEED, IS GREASE LUBRICATED. COOLANT PLANT LARGE CAPACITY TANK FOR THE COOLANT WATER, COMPLETE WITH ELECTRIC EQUIPMENT. EQUIPPED WITH COOLANT MAGNET CLEANER AND COOLANT PAPER ROLL CLEANER. PROTECTIONS FOR THE PROTECTION OF THE OPERATOR ALL MOVABLE PARTS ARE COVERED WITH SUITABLE GUARDS. PRECISELY: PROTECTION CASING FOR BELTS, PROTECTION CASING FOR GRINDING WHEEL AND BELLOWS FOR GUIDES. THE MACHINE IS COMPLETELY CLOSED AND THE FRONT PROTECTION IS A SHEET SLIDING DOORS WITH POLY-CARBONATE SHIELDS. A SAFETY DEVICE, DOES NOT PERMIT THE AUTOMATIC CYCLE TO START IF THE FRONT SLIDING DOORS ARE OPEN.
Vendedor: GK Werkzeugmaschinen GmbH
Año de construcción: usado
Ubicación: Land-complete 2nd hand packaging and palletizing system line exist of:

- bag machine
- dosing device, supplier fix steimel
- bag closing machine
- label printer
- conveying system
- palletizing machine from supplier moellers
- tubular film wrapping machine from supplier moellers
- full automized system from supplier moellers
- built 1998
- very good condition, ready for operation
- price in 1998 was > 1.300.000,00euro
- until sep. 2019 in operation, for sale from oct 2019
- ready for inspection in east germany
- detail information under trimetall@trimetall.net or 0049 157 75337789
- photos and videos are available in march 2019
       COMPLETE 2ND HAND PACKAGING AND PALLETIZING SYSTEM LINE EXIST OF: - BAG MACHINE - DOSING DEVICE, SUPPLIER FIX STEIMEL - BAG CLOSING MACHINE - LABEL PRINTER - CONVEYING SYSTEM - PALLETIZING MACHINE FROM SUPPLIER MOELLERS - TUBULAR FILM WRAPPING MACHINE FROM SUPPLIER MOELLERS - FULL AUTOMIZED SYSTEM FROM SUPPLIER MOELLERS - BUILT 1998 - VERY GOOD CONDITION, READY FOR OPERATION - PRICE IN 1998 WAS > 1.300.000,00EURO - UNTIL SEP. 2019 IN OPERATION, FOR SALE FROM OCT 2019 - READY FOR INSPECTION IN EAST GERMANY - DETAIL INFORMATION UNDER TRIMETALL@TRIMETALL.NET OR 0049 157 75337789 - PHOTOS AND VIDEOS ARE AVAILABLE IN MARCH 2019
Vendedor: Trimetall GmbH & Co.KG
Año de construcción: usado
Ubicación: Land-internal diameter:300 mm<br/>grinding depth: mm<br/>swing diameter:300/350 mm<br/>workpiece length - max.:2300 mm<br/>table rotating:-2/+6 °<br/>table speeds:0-4000 mm/min<br/>max. workpiece weight:400 (fliegend, 150mm von der spindelnase) kg<br/>workhead - center taper:6 mk<br/>rotation speed of workhead :0 - 400 1/min<br/>workhead motor:4 kw<br/>3-jaw chuck:250 (selbstschließend) mm<br/>grinding motor:11 kw<br/>coolant pump:2,2 kw<br/>cnc controller:siemens 840 d oder sps von siemens <br/>servo motors: <br/>autom. sensing device for grinding wheel:option <br/>: <br/>linear scales and ballscrew:in allen achsen <br/>grinding wheel dresser: <br/>: <br/>fully enclosed: <br/>: <br/>technical documentation in german language: <br/>ce-design: <br/>signal lamp: <br/>face grinding attachement:durchmesser 125 mm<br/>clamping chuck:350 (selbst zentrierend) mm<br/>: <br/>magnetic and paper filter : <br/>levellig elements: <br/>frequency control main spindel engine:für die innenschleifeinrichtung <br/>internal grinding spindle:auf anfrage <br/>internal grinding spindle:auf anfrage <br/>fixed steady rests:10-100 mm, 100-170 mm <br/><br/> performance and precision degree   robbi grinding machines are according to the international precision normes iso 2433. the table movement linearity is guaranteed by a max. deviation of  0,002 mm/mt.  the obtainable grinding roundness is :  0,4m (**)  (**)  for a test workpiece ground in our factory during machine testing        the cnc controls :  wheel head movement  (axis x) longitudinal table movement  (axis z) work head spindle rotation speed    the available programs permit the programming of the following grinding cycles  plunge  cylindrical pass   cylindrical pass with interpolation between table and wheel movement to grind taper workpieces radius   the software for the workpiece grinding operation is very simple and intuitive.   to facilitate the programming the software is equipped with an exemplifying graphics, to input the data for each parameter.      the software, has been specially studied, so as to permit also non specialised operators to programme without any problems complex workpieces.   when the workpiece grinding programme has been completed the cnc will automatically make up a summary list, where only the geometric parameters are evidenced.     this list permits with a  glance to verify the complete programme;  this operation is very helpful to verify eventual input data errors or to check rapidly a workpiece programme when reloaded from the file.        while the programme is in execution, it is possible to intervene and modify in real time the technologic parameters, such as:  increments, dwell inversion times, sparkout passes.   also, it is possible to intervene with the jog handwheel.      the grinding machine is composed of :    base  structure in normalised and stabilised cast iron with large ground guides.    the lubrication plant supplies a constant oil flow distributed over the complete length of the guides.    in the middle of the base, there is positioned the ball screw  for the table longitudinal movement.    on all the lower part of the perimeter are situated the recesses for machine levelling.  considering the base structure, usually a foundation is not required.    table   the table is manufactured in two parts, both are in normalised and stabilised cast iron.     the lower  part is composed of wide guides which are ground and accurately hand scrapped, for a better sliding.       the upper part, is swivelable in the two directions, suitable for grinding tapered workpieces.    it includes  a micrometric device with centesimal dial gauge for taper control.       workhead  the structure in normalised, stabilised and well ribbed cast iron, allows to support the workpiece weight and the force generated by the grinding operation.      the spindle rotates on high precision ball bearings, guaranteeing restricted tolerance and maximum rigidity in the working.      the spindle rotation is by means of a three phase motor with variable speed controlled by an inverter.  internal grinding spindle carriage  the structure is composed of a carriage, where the internal grinding spindle is located.    the working feed, is obtained by a re-circulating ball screw and preloaded nut.    the screw movement is assured by a brushless motor.       the incremental optic rule guarantees a wheelhead positioning precision of 0,001 mm.   internal grinding spindle  as there are many and various types of internal grinding spindles, according to the diameters and lengths that need to be ground, the machine is supplied without an internal grinding spindle, so that the customer may select which type is more suitable for his job.      the machine is manufactured standard with a belt transmission suitable for diam. mm. 60, diam. mm. 80 and diam. mm. 100 internal grinding spindles.      on request,  high frequency spindles may be assembled.   wheelhead  for face grinding the structure is composed of a carriage, where the face grinding device is located.    the positioning is obtained by an hydraulic cylinder.   the diamond dressing device is assembled on the face grinding device casing.   manual feed handwheels  electronic type, with double selection of the increments division 0.1 - 0.01 and 0.001 mm.  for wheelhead and table movements.     diamond dresser  the internal diamond dressing device is very strong and is positioned on the table.     it starts  hydraulically, when the dressing operation is selected, by the operator.     the dressing operation may be carried out manually or in automatic cycle.    equipment and electrical plant  in a cooled cabinet, separate from the machine.      hydraulic plant   the hydraulic power pack, is separate from the machine and activates the hydraulic diamond dresser and face grinding device.       lubrication plant the lubrication power pack, is separate from the machine and supplies continuous oil to the wheelhead guides.   the recovered oil is filtered and then resent to the power pack.     the re-circulating ball screw nut for the working feed, is grease lubricated.           coolant plant  large capacity tank for the coolant water, complete with electric equipment.       equipped with coolant magnet cleaner  and coolant paper roll cleaner.       protections  for the protection of the operator all movable parts are covered with suitable guards.     precisely: protection casing for belts, protection casing for grinding wheel and bellows for guides.   the machine is completely closed and the front protection is a sheet sliding doors with poly-carbonate shields.   a safety device, does not permit the automatic cycle to start if the front sliding doors are open.   INTERNAL DIAMETER:300 MM
GRINDING DEPTH: MM
SWING DIAMETER:300/350 MM
WORKPIECE LENGTH - MAX.:2300 MM
TABLE ROTATING:-2/+6 °
TABLE SPEEDS:0-4000 MM/MIN
MAX. WORKPIECE WEIGHT:400 (FLIEGEND, 150MM VON DER SPINDELNASE) KG
WORKHEAD - CENTER TAPER:6 MK
ROTATION SPEED OF WORKHEAD :0 - 400 1/MIN
WORKHEAD MOTOR:4 KW
3-JAW CHUCK:250 (SELBSTSCHLIEßEND) MM
GRINDING MOTOR:11 KW
COOLANT PUMP:2,2 KW
CNC CONTROLLER:SIEMENS 840 D ODER SPS VON SIEMENS
SERVO MOTORS:
AUTOM. SENSING DEVICE FOR GRINDING WHEEL:OPTION
:
LINEAR SCALES AND BALLSCREW:IN ALLEN ACHSEN
GRINDING WHEEL DRESSER:
:
FULLY ENCLOSED:
:
TECHNICAL DOCUMENTATION IN GERMAN LANGUAGE:
CE-DESIGN:
SIGNAL LAMP:
FACE GRINDING ATTACHEMENT:DURCHMESSER 125 MM
CLAMPING CHUCK:350 (SELBST ZENTRIEREND) MM
:
MAGNETIC AND PAPER FILTER :
LEVELLIG ELEMENTS:
FREQUENCY CONTROL MAIN SPINDEL ENGINE:FüR DIE INNENSCHLEIFEINRICHTUNG
INTERNAL GRINDING SPINDLE:AUF ANFRAGE
INTERNAL GRINDING SPINDLE:AUF ANFRAGE
FIXED STEADY RESTS:10-100 MM, 100-170 MM

PERFORMANCE AND PRECISION DEGREE ROBBI GRINDING MACHINES ARE ACCORDING TO THE INTERNATIONAL PRECISION NORMES ISO 2433. THE TABLE MOVEMENT LINEARITY IS GUARANTEED BY A MAX. DEVIATION OF 0,002 MM/MT. THE OBTAINABLE GRINDING ROUNDNESS IS : 0,4M (**) (**) FOR A TEST WORKPIECE GROUND IN OUR FACTORY DURING MACHINE TESTING THE CNC CONTROLS : WHEEL HEAD MOVEMENT (AXIS X) LONGITUDINAL TABLE MOVEMENT (AXIS Z) WORK HEAD SPINDLE ROTATION SPEED THE AVAILABLE PROGRAMS PERMIT THE PROGRAMMING OF THE FOLLOWING GRINDING CYCLES PLUNGE CYLINDRICAL PASS CYLINDRICAL PASS WITH INTERPOLATION BETWEEN TABLE AND WHEEL MOVEMENT TO GRIND TAPER WORKPIECES RADIUS THE SOFTWARE FOR THE WORKPIECE GRINDING OPERATION IS VERY SIMPLE AND INTUITIVE. TO FACILITATE THE PROGRAMMING THE SOFTWARE IS EQUIPPED WITH AN EXEMPLIFYING GRAPHICS, TO INPUT THE DATA FOR EACH PARAMETER. THE SOFTWARE, HAS BEEN SPECIALLY STUDIED, SO AS TO PERMIT ALSO NON SPECIALISED OPERATORS TO PROGRAMME WITHOUT ANY PROBLEMS COMPLEX WORKPIECES. WHEN THE WORKPIECE GRINDING PROGRAMME HAS BEEN COMPLETED THE CNC WILL AUTOMATICALLY MAKE UP A SUMMARY LIST, WHERE ONLY THE GEOMETRIC PARAMETERS ARE EVIDENCED. THIS LIST PERMITS WITH A GLANCE TO VERIFY THE COMPLETE PROGRAMME; THIS OPERATION IS VERY HELPFUL TO VERIFY EVENTUAL INPUT DATA ERRORS OR TO CHECK RAPIDLY A WORKPIECE PROGRAMME WHEN RELOADED FROM THE FILE. WHILE THE PROGRAMME IS IN EXECUTION, IT IS POSSIBLE TO INTERVENE AND MODIFY IN REAL TIME THE TECHNOLOGIC PARAMETERS, SUCH AS: INCREMENTS, DWELL INVERSION TIMES, SPARKOUT PASSES. ALSO, IT IS POSSIBLE TO INTERVENE WITH THE JOG HANDWHEEL. THE GRINDING MACHINE IS COMPOSED OF : BASE STRUCTURE IN NORMALISED AND STABILISED CAST IRON WITH LARGE GROUND GUIDES. THE LUBRICATION PLANT SUPPLIES A CONSTANT OIL FLOW DISTRIBUTED OVER THE COMPLETE LENGTH OF THE GUIDES. IN THE MIDDLE OF THE BASE, THERE IS POSITIONED THE BALL SCREW FOR THE TABLE LONGITUDINAL MOVEMENT. ON ALL THE LOWER PART OF THE PERIMETER ARE SITUATED THE RECESSES FOR MACHINE LEVELLING. CONSIDERING THE BASE STRUCTURE, USUALLY A FOUNDATION IS NOT REQUIRED. TABLE THE TABLE IS MANUFACTURED IN TWO PARTS, BOTH ARE IN NORMALISED AND STABILISED CAST IRON. THE LOWER PART IS COMPOSED OF WIDE GUIDES WHICH ARE GROUND AND ACCURATELY HAND SCRAPPED, FOR A BETTER SLIDING. THE UPPER PART, IS SWIVELABLE IN THE TWO DIRECTIONS, SUITABLE FOR GRINDING TAPERED WORKPIECES. IT INCLUDES A MICROMETRIC DEVICE WITH CENTESIMAL DIAL GAUGE FOR TAPER CONTROL. WORKHEAD THE STRUCTURE IN NORMALISED, STABILISED AND WELL RIBBED CAST IRON, ALLOWS TO SUPPORT THE WORKPIECE WEIGHT AND THE FORCE GENERATED BY THE GRINDING OPERATION. THE SPINDLE ROTATES ON HIGH PRECISION BALL BEARINGS, GUARANTEEING RESTRICTED TOLERANCE AND MAXIMUM RIGIDITY IN THE WORKING. THE SPINDLE ROTATION IS BY MEANS OF A THREE PHASE MOTOR WITH VARIABLE SPEED CONTROLLED BY AN INVERTER. INTERNAL GRINDING SPINDLE CARRIAGE THE STRUCTURE IS COMPOSED OF A CARRIAGE, WHERE THE INTERNAL GRINDING SPINDLE IS LOCATED. THE WORKING FEED, IS OBTAINED BY A RE-CIRCULATING BALL SCREW AND PRELOADED NUT. THE SCREW MOVEMENT IS ASSURED BY A BRUSHLESS MOTOR. THE INCREMENTAL OPTIC RULE GUARANTEES A WHEELHEAD POSITIONING PRECISION OF 0,001 MM. INTERNAL GRINDING SPINDLE AS THERE ARE MANY AND VARIOUS TYPES OF INTERNAL GRINDING SPINDLES, ACCORDING TO THE DIAMETERS AND LENGTHS THAT NEED TO BE GROUND, THE MACHINE IS SUPPLIED WITHOUT AN INTERNAL GRINDING SPINDLE, SO THAT THE CUSTOMER MAY SELECT WHICH TYPE IS MORE SUITABLE FOR HIS JOB. THE MACHINE IS MANUFACTURED STANDARD WITH A BELT TRANSMISSION SUITABLE FOR DIAM. MM. 60, DIAM. MM. 80 AND DIAM. MM. 100 INTERNAL GRINDING SPINDLES. ON REQUEST, HIGH FREQUENCY SPINDLES MAY BE ASSEMBLED. WHEELHEAD FOR FACE GRINDING THE STRUCTURE IS COMPOSED OF A CARRIAGE, WHERE THE FACE GRINDING DEVICE IS LOCATED. THE POSITIONING IS OBTAINED BY AN HYDRAULIC CYLINDER. THE DIAMOND DRESSING DEVICE IS ASSEMBLED ON THE FACE GRINDING DEVICE CASING. MANUAL FEED HANDWHEELS ELECTRONIC TYPE, WITH DOUBLE SELECTION OF THE INCREMENTS DIVISION 0.1 - 0.01 AND 0.001 MM. FOR WHEELHEAD AND TABLE MOVEMENTS. DIAMOND DRESSER THE INTERNAL DIAMOND DRESSING DEVICE IS VERY STRONG AND IS POSITIONED ON THE TABLE. IT STARTS HYDRAULICALLY, WHEN THE DRESSING OPERATION IS SELECTED, BY THE OPERATOR. THE DRESSING OPERATION MAY BE CARRIED OUT MANUALLY OR IN AUTOMATIC CYCLE. EQUIPMENT AND ELECTRICAL PLANT IN A COOLED CABINET, SEPARATE FROM THE MACHINE. HYDRAULIC PLANT THE HYDRAULIC POWER PACK, IS SEPARATE FROM THE MACHINE AND ACTIVATES THE HYDRAULIC DIAMOND DRESSER AND FACE GRINDING DEVICE. LUBRICATION PLANT THE LUBRICATION POWER PACK, IS SEPARATE FROM THE MACHINE AND SUPPLIES CONTINUOUS OIL TO THE WHEELHEAD GUIDES. THE RECOVERED OIL IS FILTERED AND THEN RESENT TO THE POWER PACK. THE RE-CIRCULATING BALL SCREW NUT FOR THE WORKING FEED, IS GREASE LUBRICATED. COOLANT PLANT LARGE CAPACITY TANK FOR THE COOLANT WATER, COMPLETE WITH ELECTRIC EQUIPMENT. EQUIPPED WITH COOLANT MAGNET CLEANER AND COOLANT PAPER ROLL CLEANER. PROTECTIONS FOR THE PROTECTION OF THE OPERATOR ALL MOVABLE PARTS ARE COVERED WITH SUITABLE GUARDS. PRECISELY: PROTECTION CASING FOR BELTS, PROTECTION CASING FOR GRINDING WHEEL AND BELLOWS FOR GUIDES. THE MACHINE IS COMPLETELY CLOSED AND THE FRONT PROTECTION IS A SHEET SLIDING DOORS WITH POLY-CARBONATE SHIELDS. A SAFETY DEVICE, DOES NOT PERMIT THE AUTOMATIC CYCLE TO START IF THE FRONT SLIDING DOORS ARE OPEN.
Vendedor: GK Werkzeugmaschinen GmbH
Año de construcción: usado
Ubicación: Land-300 tons tie-bar-less imm built in 2008 with cc 200 control, integrated engel robot erc 33/2-f, crane for mould fixing (2tons), 16 hot chanel, accumulator for fast injection and parallel movements. 2 core puller fix platen, flow meter, transport belt. plastizising screw bimetalic.

technical details	
daylight max	1.300 mm
min. mould hight	400 mm
year of building	2008
working hours	73506
injection pressure	1.616/2.053 bar
injection volumen	511 cm3
nominal capacity of pump motor	45 kw
travel opening	900 mm
screw diameter	55 mm
platen size	1.100 x 1.000 mm
clamping force	3.000 kn 300 TONS TIE-BAR-LESS IMM BUILT IN 2008 WITH CC 200 CONTROL, INTEGRATED ENGEL ROBOT ERC 33/2-F, CRANE FOR MOULD FIXING (2TONS), 16 HOT CHANEL, ACCUMULATOR FOR FAST INJECTION AND PARALLEL MOVEMENTS. 2 CORE PULLER FIX PLATEN, FLOW METER, TRANSPORT BELT. PLASTIZISING SCREW BIMETALIC. TECHNICAL DETAILS DAYLIGHT MAX 1.300 MM MIN. MOULD HIGHT 400 MM YEAR OF BUILDING 2008 WORKING HOURS 73506 INJECTION PRESSURE 1.616/2.053 BAR INJECTION VOLUMEN 511 CM3 NOMINAL CAPACITY OF PUMP MOTOR 45 KW TRAVEL OPENING 900 MM SCREW DIAMETER 55 MM PLATEN SIZE 1.100 X 1.000 MM CLAMPING FORCE 3.000 KN
Vendedor: Udo Krichbaum TRANSITUS, S.L.
Año de construcción: usado
Ubicación: Land-internal diameter:250 mm<br/>grinding depth: mm<br/>swing diameter:460 mm<br/>workpiece diameter:455 (max.) mm<br/>workpiece length - max.:1000 mm<br/>table rotating:-4/+8 °<br/>table speeds:0-4000 mm/min<br/>max. workpiece weight:80 kg<br/>workhead - center taper:5 mk<br/>rotation speed of workhead :0 - 400 1/min<br/>workhead motor:4 kw<br/>3-jaw chuck:250 (selbstschließend) mm<br/>grinding motor:4 kw<br/>coolant pump:2,2 kw<br/>weight approx.:2,4 t<br/>machine dimensions:3200 x 2100 xx<br/>cnc controller:siemens 840 d <br/>servo motors: <br/>autom. sensing device for grinding wheel:option <br/>: <br/>linear scales and ballscrew:in allen achsen <br/>grinding wheel dresser: <br/>: <br/>fully enclosed: <br/>: <br/>technical documentation in german language: <br/>ce-design: <br/>signal lamp: <br/>face grinding attachement:durchmesser 125 mm<br/>clamping chuck:250 (selbstschließend), 1 satz harte backen, 1 satz weiche backen, 1 satz innen mm<br/>: <br/>magnetic and paper filter : <br/>levellig elements: <br/>frequency control main spindel engine:für die innenschleifeinrichtung <br/>internal grinding spindle:rpm 28.000, diam. 60 mm. min. diam. cap. 25 mm. x bohrung 50 mm, max. diam. cap. 100 mm. x bohrung 115 mm . <br/>internal grinding spindle:rpm 10.000, diam. 100 mm, min. diam. cap. 50 mm x bohrung 100 mm, max.diam. cap. 250 mm xbohrung 220 mm <br/>fixed steady rests:10-100 mm, 100-170 mm <br/><br/> performance and precision degree   robbi grinding machines are according to the international precision normes iso 2433. the table movement linearity is guaranteed by a max. deviation of  0,002 mm/mt.  the obtainable grinding roundness is :  0,4m (**)  (**)  for a test workpiece ground in our factory during machine testing        the cnc controls :  wheel head movement  (axis x) longitudinal table movement  (axis z) work head spindle rotation speed    the available programs permit the programming of the following grinding cycles  plunge  cylindrical pass   cylindrical pass with interpolation between table and wheel movement to grind taper workpieces radius   the software for the workpiece grinding operation is very simple and intuitive.   to facilitate the programming the software is equipped with an exemplifying graphics, to input the data for each parameter.      the software, has been specially studied, so as to permit also non specialised operators to programme without any problems complex workpieces.   when the workpiece grinding programme has been completed the cnc will automatically make up a summary list, where only the geometric parameters are evidenced.     this list permits with a  glance to verify the complete programme;  this operation is very helpful to verify eventual input data errors or to check rapidly a workpiece programme when reloaded from the file.        while the programme is in execution, it is possible to intervene and modify in real time the technologic parameters, such as:  increments, dwell inversion times, sparkout passes.   also, it is possible to intervene with the jog handwheel.      the grinding machine is composed of :    base  structure in normalised and stabilised cast iron with large ground guides.    the lubrication plant supplies a constant oil flow distributed over the complete length of the guides.    in the middle of the base, there is positioned the ball screw  for the table longitudinal movement.    on all the lower part of the perimeter are situated the recesses for machine levelling.  considering the base structure, usually a foundation is not required.    table   the table is manufactured in two parts, both are in normalised and stabilised cast iron.     the lower  part is composed of wide guides which are ground and accurately hand scrapped, for a better sliding.       the upper part, is swivelable in the two directions, suitable for grinding tapered workpieces.    it includes  a micrometric device with centesimal dial gauge for taper control.       workhead  the structure in normalised, stabilised and well ribbed cast iron, allows to support the workpiece weight and the force generated by the grinding operation.      the spindle rotates on high precision ball bearings, guaranteeing restricted tolerance and maximum rigidity in the working.      the spindle rotation is by means of a three phase motor with variable speed controlled by an inverter.  internal grinding spindle carriage  the structure is composed of a carriage, where the internal grinding spindle is located.    the working feed, is obtained by a re-circulating ball screw and preloaded nut.    the screw movement is assured by a brushless motor.       the incremental optic rule guarantees a wheelhead positioning precision of 0,001 mm.   internal grinding spindle  as there are many and various types of internal grinding spindles, according to the diameters and lengths that need to be ground, the machine is supplied without an internal grinding spindle, so that the customer may select which type is more suitable for his job.      the machine is manufactured standard with a belt transmission suitable for diam. mm. 60, diam. mm. 80 and diam. mm. 100 internal grinding spindles.      on request,  high frequency spindles may be assembled.   wheelhead  for face grinding the structure is composed of a carriage, where the face grinding device is located.    the positioning is obtained by an hydraulic cylinder.   the diamond dressing device is assembled on the face grinding device casing.   manual feed handwheels  electronic type, with double selection of the increments division 0.1 - 0.01 and 0.001 mm.  for wheelhead and table movements.     diamond dresser  the internal diamond dressing device is very strong and is positioned on the table.     it starts  hydraulically, when the dressing operation is selected, by the operator.     the dressing operation may be carried out manually or in automatic cycle.    equipment and electrical plant  in a cooled cabinet, separate from the machine.      hydraulic plant   the hydraulic power pack, is separate from the machine and activates the hydraulic diamond dresser and face grinding device.       lubrication plant the lubrication power pack, is separate from the machine and supplies continuous oil to the wheelhead guides.   the recovered oil is filtered and then resent to the power pack.     the re-circulating ball screw nut for the working feed, is grease lubricated.           coolant plant  large capacity tank for the coolant water, complete with electric equipment.       equipped with coolant magnet cleaner  and coolant paper roll cleaner.       protections  for the protection of the operator all movable parts are covered with suitable guards.     precisely: protection casing for belts, protection casing for grinding wheel and bellows for guides.   the machine is completely closed and the front protection is a sheet sliding doors with poly-carbonate shields.   a safety device, does not permit the automatic cycle to start if the front sliding doors are open.   INTERNAL DIAMETER:250 MM
GRINDING DEPTH: MM
SWING DIAMETER:460 MM
WORKPIECE DIAMETER:455 (MAX.) MM
WORKPIECE LENGTH - MAX.:1000 MM
TABLE ROTATING:-4/+8 °
TABLE SPEEDS:0-4000 MM/MIN
MAX. WORKPIECE WEIGHT:80 KG
WORKHEAD - CENTER TAPER:5 MK
ROTATION SPEED OF WORKHEAD :0 - 400 1/MIN
WORKHEAD MOTOR:4 KW
3-JAW CHUCK:250 (SELBSTSCHLIEßEND) MM
GRINDING MOTOR:4 KW
COOLANT PUMP:2,2 KW
WEIGHT APPROX.:2,4 T
MACHINE DIMENSIONS:3200 X 2100 XX
CNC CONTROLLER:SIEMENS 840 D
SERVO MOTORS:
AUTOM. SENSING DEVICE FOR GRINDING WHEEL:OPTION
:
LINEAR SCALES AND BALLSCREW:IN ALLEN ACHSEN
GRINDING WHEEL DRESSER:
:
FULLY ENCLOSED:
:
TECHNICAL DOCUMENTATION IN GERMAN LANGUAGE:
CE-DESIGN:
SIGNAL LAMP:
FACE GRINDING ATTACHEMENT:DURCHMESSER 125 MM
CLAMPING CHUCK:250 (SELBSTSCHLIEßEND), 1 SATZ HARTE BACKEN, 1 SATZ WEICHE BACKEN, 1 SATZ INNEN MM
:
MAGNETIC AND PAPER FILTER :
LEVELLIG ELEMENTS:
FREQUENCY CONTROL MAIN SPINDEL ENGINE:FüR DIE INNENSCHLEIFEINRICHTUNG
INTERNAL GRINDING SPINDLE:RPM 28.000, DIAM. 60 MM. MIN. DIAM. CAP. 25 MM. X BOHRUNG 50 MM, MAX. DIAM. CAP. 100 MM. X BOHRUNG 115 MM .
INTERNAL GRINDING SPINDLE:RPM 10.000, DIAM. 100 MM, MIN. DIAM. CAP. 50 MM X BOHRUNG 100 MM, MAX.DIAM. CAP. 250 MM XBOHRUNG 220 MM
FIXED STEADY RESTS:10-100 MM, 100-170 MM

PERFORMANCE AND PRECISION DEGREE ROBBI GRINDING MACHINES ARE ACCORDING TO THE INTERNATIONAL PRECISION NORMES ISO 2433. THE TABLE MOVEMENT LINEARITY IS GUARANTEED BY A MAX. DEVIATION OF 0,002 MM/MT. THE OBTAINABLE GRINDING ROUNDNESS IS : 0,4M (**) (**) FOR A TEST WORKPIECE GROUND IN OUR FACTORY DURING MACHINE TESTING THE CNC CONTROLS : WHEEL HEAD MOVEMENT (AXIS X) LONGITUDINAL TABLE MOVEMENT (AXIS Z) WORK HEAD SPINDLE ROTATION SPEED THE AVAILABLE PROGRAMS PERMIT THE PROGRAMMING OF THE FOLLOWING GRINDING CYCLES PLUNGE CYLINDRICAL PASS CYLINDRICAL PASS WITH INTERPOLATION BETWEEN TABLE AND WHEEL MOVEMENT TO GRIND TAPER WORKPIECES RADIUS THE SOFTWARE FOR THE WORKPIECE GRINDING OPERATION IS VERY SIMPLE AND INTUITIVE. TO FACILITATE THE PROGRAMMING THE SOFTWARE IS EQUIPPED WITH AN EXEMPLIFYING GRAPHICS, TO INPUT THE DATA FOR EACH PARAMETER. THE SOFTWARE, HAS BEEN SPECIALLY STUDIED, SO AS TO PERMIT ALSO NON SPECIALISED OPERATORS TO PROGRAMME WITHOUT ANY PROBLEMS COMPLEX WORKPIECES. WHEN THE WORKPIECE GRINDING PROGRAMME HAS BEEN COMPLETED THE CNC WILL AUTOMATICALLY MAKE UP A SUMMARY LIST, WHERE ONLY THE GEOMETRIC PARAMETERS ARE EVIDENCED. THIS LIST PERMITS WITH A GLANCE TO VERIFY THE COMPLETE PROGRAMME; THIS OPERATION IS VERY HELPFUL TO VERIFY EVENTUAL INPUT DATA ERRORS OR TO CHECK RAPIDLY A WORKPIECE PROGRAMME WHEN RELOADED FROM THE FILE. WHILE THE PROGRAMME IS IN EXECUTION, IT IS POSSIBLE TO INTERVENE AND MODIFY IN REAL TIME THE TECHNOLOGIC PARAMETERS, SUCH AS: INCREMENTS, DWELL INVERSION TIMES, SPARKOUT PASSES. ALSO, IT IS POSSIBLE TO INTERVENE WITH THE JOG HANDWHEEL. THE GRINDING MACHINE IS COMPOSED OF : BASE STRUCTURE IN NORMALISED AND STABILISED CAST IRON WITH LARGE GROUND GUIDES. THE LUBRICATION PLANT SUPPLIES A CONSTANT OIL FLOW DISTRIBUTED OVER THE COMPLETE LENGTH OF THE GUIDES. IN THE MIDDLE OF THE BASE, THERE IS POSITIONED THE BALL SCREW FOR THE TABLE LONGITUDINAL MOVEMENT. ON ALL THE LOWER PART OF THE PERIMETER ARE SITUATED THE RECESSES FOR MACHINE LEVELLING. CONSIDERING THE BASE STRUCTURE, USUALLY A FOUNDATION IS NOT REQUIRED. TABLE THE TABLE IS MANUFACTURED IN TWO PARTS, BOTH ARE IN NORMALISED AND STABILISED CAST IRON. THE LOWER PART IS COMPOSED OF WIDE GUIDES WHICH ARE GROUND AND ACCURATELY HAND SCRAPPED, FOR A BETTER SLIDING. THE UPPER PART, IS SWIVELABLE IN THE TWO DIRECTIONS, SUITABLE FOR GRINDING TAPERED WORKPIECES. IT INCLUDES A MICROMETRIC DEVICE WITH CENTESIMAL DIAL GAUGE FOR TAPER CONTROL. WORKHEAD THE STRUCTURE IN NORMALISED, STABILISED AND WELL RIBBED CAST IRON, ALLOWS TO SUPPORT THE WORKPIECE WEIGHT AND THE FORCE GENERATED BY THE GRINDING OPERATION. THE SPINDLE ROTATES ON HIGH PRECISION BALL BEARINGS, GUARANTEEING RESTRICTED TOLERANCE AND MAXIMUM RIGIDITY IN THE WORKING. THE SPINDLE ROTATION IS BY MEANS OF A THREE PHASE MOTOR WITH VARIABLE SPEED CONTROLLED BY AN INVERTER. INTERNAL GRINDING SPINDLE CARRIAGE THE STRUCTURE IS COMPOSED OF A CARRIAGE, WHERE THE INTERNAL GRINDING SPINDLE IS LOCATED. THE WORKING FEED, IS OBTAINED BY A RE-CIRCULATING BALL SCREW AND PRELOADED NUT. THE SCREW MOVEMENT IS ASSURED BY A BRUSHLESS MOTOR. THE INCREMENTAL OPTIC RULE GUARANTEES A WHEELHEAD POSITIONING PRECISION OF 0,001 MM. INTERNAL GRINDING SPINDLE AS THERE ARE MANY AND VARIOUS TYPES OF INTERNAL GRINDING SPINDLES, ACCORDING TO THE DIAMETERS AND LENGTHS THAT NEED TO BE GROUND, THE MACHINE IS SUPPLIED WITHOUT AN INTERNAL GRINDING SPINDLE, SO THAT THE CUSTOMER MAY SELECT WHICH TYPE IS MORE SUITABLE FOR HIS JOB. THE MACHINE IS MANUFACTURED STANDARD WITH A BELT TRANSMISSION SUITABLE FOR DIAM. MM. 60, DIAM. MM. 80 AND DIAM. MM. 100 INTERNAL GRINDING SPINDLES. ON REQUEST, HIGH FREQUENCY SPINDLES MAY BE ASSEMBLED. WHEELHEAD FOR FACE GRINDING THE STRUCTURE IS COMPOSED OF A CARRIAGE, WHERE THE FACE GRINDING DEVICE IS LOCATED. THE POSITIONING IS OBTAINED BY AN HYDRAULIC CYLINDER. THE DIAMOND DRESSING DEVICE IS ASSEMBLED ON THE FACE GRINDING DEVICE CASING. MANUAL FEED HANDWHEELS ELECTRONIC TYPE, WITH DOUBLE SELECTION OF THE INCREMENTS DIVISION 0.1 - 0.01 AND 0.001 MM. FOR WHEELHEAD AND TABLE MOVEMENTS. DIAMOND DRESSER THE INTERNAL DIAMOND DRESSING DEVICE IS VERY STRONG AND IS POSITIONED ON THE TABLE. IT STARTS HYDRAULICALLY, WHEN THE DRESSING OPERATION IS SELECTED, BY THE OPERATOR. THE DRESSING OPERATION MAY BE CARRIED OUT MANUALLY OR IN AUTOMATIC CYCLE. EQUIPMENT AND ELECTRICAL PLANT IN A COOLED CABINET, SEPARATE FROM THE MACHINE. HYDRAULIC PLANT THE HYDRAULIC POWER PACK, IS SEPARATE FROM THE MACHINE AND ACTIVATES THE HYDRAULIC DIAMOND DRESSER AND FACE GRINDING DEVICE. LUBRICATION PLANT THE LUBRICATION POWER PACK, IS SEPARATE FROM THE MACHINE AND SUPPLIES CONTINUOUS OIL TO THE WHEELHEAD GUIDES. THE RECOVERED OIL IS FILTERED AND THEN RESENT TO THE POWER PACK. THE RE-CIRCULATING BALL SCREW NUT FOR THE WORKING FEED, IS GREASE LUBRICATED. COOLANT PLANT LARGE CAPACITY TANK FOR THE COOLANT WATER, COMPLETE WITH ELECTRIC EQUIPMENT. EQUIPPED WITH COOLANT MAGNET CLEANER AND COOLANT PAPER ROLL CLEANER. PROTECTIONS FOR THE PROTECTION OF THE OPERATOR ALL MOVABLE PARTS ARE COVERED WITH SUITABLE GUARDS. PRECISELY: PROTECTION CASING FOR BELTS, PROTECTION CASING FOR GRINDING WHEEL AND BELLOWS FOR GUIDES. THE MACHINE IS COMPLETELY CLOSED AND THE FRONT PROTECTION IS A SHEET SLIDING DOORS WITH POLY-CARBONATE SHIELDS. A SAFETY DEVICE, DOES NOT PERMIT THE AUTOMATIC CYCLE TO START IF THE FRONT SLIDING DOORS ARE OPEN.
Vendedor: GK Werkzeugmaschinen GmbH
Año de construcción: usado
Ubicación: Land-age 2002
like new - original packing
plate punch heidelberg
table model
220 and 425 mm pin distance
millimeter foil and register bar
delivery time: immediately from stock

please ask for price.

we ship and install worldwide! AGE 2002 LIKE NEW - ORIGINAL PACKING PLATE PUNCH HEIDELBERG TABLE MODEL 220 AND 425 MM PIN DISTANCE MILLIMETER FOIL AND REGISTER BAR DELIVERY TIME: IMMEDIATELY FROM STOCK PLEASE ASK FOR PRICE. WE SHIP AND INSTALL WORLDWIDE!
Vendedor: Altmann Graphische Maschinen GmbH
Año de construcción: usado
Ubicación: Land-please visit our website at foeth[dot]com for more information about this machine. what you can expect from foeth: ?machine is in working condition ?at a reduced price compared to new ?ready for shipping to any destination worldwide ?you are welcome to inspect the machine in barneveld, the netherlands. visit our website foeth dot com for many more machines! PLEASE VISIT OUR WEBSITE AT FOETH[DOT]COM FOR MORE INFORMATION ABOUT THIS MACHINE. WHAT YOU CAN EXPECT FROM FOETH: ?MACHINE IS IN WORKING CONDITION ?AT A REDUCED PRICE COMPARED TO NEW ?READY FOR SHIPPING TO ANY DESTINATION WORLDWIDE ?YOU ARE WELCOME TO INSPECT THE MACHINE IN BARNEVELD, THE NETHERLANDS. VISIT OUR WEBSITE FOETH DOT COM FOR MANY MORE MACHINES!
Vendedor: Foeth
Año de construcción: usado
Ubicación: Land-max. output: 24kg/h, number of hoppers: 4, including movable frame and three vacuum conveyors.  MAX. OUTPUT: 24KG/H, NUMBER OF HOPPERS: 4, INCLUDING MOVABLE FRAME AND THREE VACUUM CONVEYORS.
Vendedor: Innovac GmbH
Año de construcción: usado
Precio: 8.920 €
Ubicación: Land-: 60 °<br/>: 45 °<br/>: 1,5/2,2 kw<br/>: 180 mm<br/>: 750 mm<br/>: 950 mm<br/>: 2.050 mm<br/>: 443 kg<br/>semiautomatic circular saw to also cut high strength steels<br/>with electropneumatic functioning, hydraulic control down-feed speed of the head<br/>linear guide of sawinghead mit hydraulic controlled feed<br/>pneumatic machine vice, movable sideways with additional clapming strip for reduced cuttinag burr<br/>regulating clamping pressure<br/>all functions programmable<br/>presentation of sawing blade status on the display: sawing blade lifes, awing blade speed, piece counter, cycle time and malfunctions<br/>reversal of direction of rotation to remove the sawing blade out of the material if necessary<br/>coolant equiptment and washing gun<br/>sawing blade protection<br/>material stop<br/>extractable chip drawer<br/>chip brush<br/>stops at 0° and 45° left and right<br/>thermic motor protection<br/>users manual in german<br/><br/>(sawing blade not included)<br/><br/>option:<br/><br/>sawing balde for mild steel hss 370 x 3.0 x 40 mm 180z c  ? 175,-<br/><br/><br/>sawing blade dimensions: 370 x 3,0 x 40 mm<br/>mitre left: 60°<br/>mitre right: 45°<br/>speeds: 15/30 r/min<br/>motor: 1,5/2,2 kw<br/>cutting capacity 90°: round 120 mm, square 100 mm, rectangle 180 x 100 mm<br/>cutting capacity 45° right: round 120 mm, square 100 mm, rectangle 130 x 100 mm<br/>cutting capacity 60° right: round 110 mm, square 90 mm, rectangle 90 x 100 mm<br/>cutting capacity 45° left: round 105 mm, square 100 mm, rectangle 130 x 100 mm<br/>width of the opening: 180 mm<br/>width: 750 mm<br/>depth: 950 mm<br/>height: 2.050 mm<br/>weight: 443 kg<br/><br/><br/><br/> : 60 °
: 45 °
: 1,5/2,2 KW
: 180 MM
: 750 MM
: 950 MM
: 2.050 MM
: 443 KG
SEMIAUTOMATIC CIRCULAR SAW TO ALSO CUT HIGH STRENGTH STEELS
WITH ELECTROPNEUMATIC FUNCTIONING, HYDRAULIC CONTROL DOWN-FEED SPEED OF THE HEAD
LINEAR GUIDE OF SAWINGHEAD MIT HYDRAULIC CONTROLLED FEED
PNEUMATIC MACHINE VICE, MOVABLE SIDEWAYS WITH ADDITIONAL CLAPMING STRIP FOR REDUCED CUTTINAG BURR
REGULATING CLAMPING PRESSURE
ALL FUNCTIONS PROGRAMMABLE
PRESENTATION OF SAWING BLADE STATUS ON THE DISPLAY: SAWING BLADE LIFES, AWING BLADE SPEED, PIECE COUNTER, CYCLE TIME AND MALFUNCTIONS
REVERSAL OF DIRECTION OF ROTATION TO REMOVE THE SAWING BLADE OUT OF THE MATERIAL IF NECESSARY
COOLANT EQUIPTMENT AND WASHING GUN
SAWING BLADE PROTECTION
MATERIAL STOP
EXTRACTABLE CHIP DRAWER
CHIP BRUSH
STOPS AT 0° AND 45° LEFT AND RIGHT
THERMIC MOTOR PROTECTION
USERS MANUAL IN GERMAN

(SAWING BLADE NOT INCLUDED)

OPTION:

SAWING BALDE FOR MILD STEEL HSS 370 X 3.0 X 40 MM 180Z C  ? 175,-


SAWING BLADE DIMENSIONS: 370 X 3,0 X 40 MM
MITRE LEFT: 60°
MITRE RIGHT: 45°
SPEEDS: 15/30 R/MIN
MOTOR: 1,5/2,2 KW
CUTTING CAPACITY 90°: ROUND 120 MM, SQUARE 100 MM, RECTANGLE 180 X 100 MM
CUTTING CAPACITY 45° RIGHT: ROUND 120 MM, SQUARE 100 MM, RECTANGLE 130 X 100 MM
CUTTING CAPACITY 60° RIGHT: ROUND 110 MM, SQUARE 90 MM, RECTANGLE 90 X 100 MM
CUTTING CAPACITY 45° LEFT: ROUND 105 MM, SQUARE 100 MM, RECTANGLE 130 X 100 MM
WIDTH OF THE OPENING: 180 MM
WIDTH: 750 MM
DEPTH: 950 MM
HEIGHT: 2.050 MM
WEIGHT: 443 KG



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land--machine in stock
-after reviewing the technical
-vg condition

technical parameters:

-main engine power 37 kw
-engine power from the hydraulic pump 1.5 kw
-total power: 39.25 kw
-engine power ?mijki 0.75 kw

-automatic autorewers
-pull hydraulic
-rotation 90 u/min

-the rotor length 1500 mm
-multiple staggered knife shaft stuk 34
-dimensions: 40 mm x 40 mm
-sieve fi 20 mm
-knives lace

-diameter suction fi 250
-rotor diameter 275 mm
-height of drawers foot 275 mm
-the length of the drawer pressure 800 mm

overall dimensions of the machine:

-length of 270 cm
width 230 cm
-height 200 cm
-weight 3500 kg

wood chipper can process a wide range of wood waste, which accumulate, for example. in industrial applications or carpentry workshops, saw mills or in the furniture industry. this list includes pallets and boxes, as well as long and short scrap of wood, veneer, chipboard, fibreboard, plywood and joiner's products, such as large furniture, window profiles, doors and stairs.

the main features of the machine:

* robust construction
* a reputable german brand weima
* the leader among manufacturers of chippers
the commendable
* for each professional

patented v rotor

-the optimum supply of material
-minimum cutter wear
– small power consumption at high performance
is a small gap between the rotor and blades kontruj?cymi
-defined issue knife

contoured v rotor is made of die-cast and placed on a stable bearings
on its perimeter welded are special grips knife in his pockets
in them are cutting knives and bolted
this enables fast replacement blades
thanks to this design during the shredding material screws are damaged
recessed cutting blades have 4 cutting edges, which can be 4 x turn,
providing precise cutting with high performance. -MACHINE IN STOCK -AFTER REVIEWING THE TECHNICAL -VG CONDITION TECHNICAL PARAMETERS: -MAIN ENGINE POWER 37 KW -ENGINE POWER FROM THE HYDRAULIC PUMP 1.5 KW -TOTAL POWER: 39.25 KW -ENGINE POWER ?MIJKI 0.75 KW -AUTOMATIC AUTOREWERS -PULL HYDRAULIC -ROTATION 90 U/MIN -THE ROTOR LENGTH 1500 MM -MULTIPLE STAGGERED KNIFE SHAFT STUK 34 -DIMENSIONS: 40 MM X 40 MM -SIEVE FI 20 MM -KNIVES LACE -DIAMETER SUCTION FI 250 -ROTOR DIAMETER 275 MM -HEIGHT OF DRAWERS FOOT 275 MM -THE LENGTH OF THE DRAWER PRESSURE 800 MM OVERALL DIMENSIONS OF THE MACHINE: -LENGTH OF 270 CM WIDTH 230 CM -HEIGHT 200 CM -WEIGHT 3500 KG WOOD CHIPPER CAN PROCESS A WIDE RANGE OF WOOD WASTE, WHICH ACCUMULATE, FOR EXAMPLE. IN INDUSTRIAL APPLICATIONS OR CARPENTRY WORKSHOPS, SAW MILLS OR IN THE FURNITURE INDUSTRY. THIS LIST INCLUDES PALLETS AND BOXES, AS WELL AS LONG AND SHORT SCRAP OF WOOD, VENEER, CHIPBOARD, FIBREBOARD, PLYWOOD AND JOINER'S PRODUCTS, SUCH AS LARGE FURNITURE, WINDOW PROFILES, DOORS AND STAIRS. THE MAIN FEATURES OF THE MACHINE: * ROBUST CONSTRUCTION * A REPUTABLE GERMAN BRAND WEIMA * THE LEADER AMONG MANUFACTURERS OF CHIPPERS THE COMMENDABLE * FOR EACH PROFESSIONAL PATENTED V ROTOR -THE OPTIMUM SUPPLY OF MATERIAL -MINIMUM CUTTER WEAR – SMALL POWER CONSUMPTION AT HIGH PERFORMANCE IS A SMALL GAP BETWEEN THE ROTOR AND BLADES KONTRUJ?CYMI -DEFINED ISSUE KNIFE CONTOURED V ROTOR IS MADE OF DIE-CAST AND PLACED ON A STABLE BEARINGS ON ITS PERIMETER WELDED ARE SPECIAL GRIPS KNIFE IN HIS POCKETS IN THEM ARE CUTTING KNIVES AND BOLTED THIS ENABLES FAST REPLACEMENT BLADES THANKS TO THIS DESIGN DURING THE SHREDDING MATERIAL SCREWS ARE DAMAGED RECESSED CUTTING BLADES HAVE 4 CUTTING EDGES, WHICH CAN BE 4 X TURN, PROVIDING PRECISE CUTTING WITH HIGH PERFORMANCE.
Vendedor: StanDrew
Año de construcción: usado
Ubicación: Land-: 4.250 x 34 x 1,1 mm<br/>: 845 mm<br/>: 2,2 kw<br/>: 4.120 x 2.300 x 2.180 mm<br/>: 1.900 kg<br/>full automatic band saw<br/>integrated keyboard with cnc control<br/>large ram memory<br/>save over 300 cutting programs<br/>strong steel structure<br/>single-block gear motor<br/>no vibrations during cutting<br/>adjustable descent speed<br/>mobile control console<br/>electronic inverter for variable speed<br/>single stroke feeder<br/>automatic detection of material width<br/>roller table integrated<br/>10 inch lcd-touch screen<br/><br/><br/><br/><br/><br/>cutting capacity:<br/>90°: round 350 mm <br/> square 330 mm <br/> rectangular 500 x 310 mm<br/>45° right: round 320 mm <br/> square 320 mm <br/> rectangular 320 x 320 mm<br/>60° right: round 150 mm <br/> square 150 mm <br/> rectangular 150 x 320 mm<br/>45° left: round 300 mm <br/> square 300 mm <br/> rectangular 300 x 320 mm<br/>60° left: round 150 mm <br/> square 150 mm <br/> rectangular 150 x 320 mm<br/>blade dimension: 4.250 x 34 x 1,1 mm<br/>speed: 18/100 m/min<br/>working height: 845 mm<br/>motor: 2,2 kw<br/>dimensions: 4.120 x 2.300 x 2.180 mm<br/>weight: 1.900 kg<br/><br/><br/><br/> : 4.250 X 34 X 1,1 MM
: 845 MM
: 2,2 KW
: 4.120 X 2.300 X 2.180 MM
: 1.900 KG
FULL AUTOMATIC BAND SAW
INTEGRATED KEYBOARD WITH CNC CONTROL
LARGE RAM MEMORY
SAVE OVER 300 CUTTING PROGRAMS
STRONG STEEL STRUCTURE
SINGLE-BLOCK GEAR MOTOR
NO VIBRATIONS DURING CUTTING
ADJUSTABLE DESCENT SPEED
MOBILE CONTROL CONSOLE
ELECTRONIC INVERTER FOR VARIABLE SPEED
SINGLE STROKE FEEDER
AUTOMATIC DETECTION OF MATERIAL WIDTH
ROLLER TABLE INTEGRATED
10 INCH LCD-TOUCH SCREEN





CUTTING CAPACITY:
90°: ROUND 350 MM
SQUARE 330 MM
RECTANGULAR 500 X 310 MM
45° RIGHT: ROUND 320 MM
SQUARE 320 MM
RECTANGULAR 320 X 320 MM
60° RIGHT: ROUND 150 MM
SQUARE 150 MM
RECTANGULAR 150 X 320 MM
45° LEFT: ROUND 300 MM
SQUARE 300 MM
RECTANGULAR 300 X 320 MM
60° LEFT: ROUND 150 MM
SQUARE 150 MM
RECTANGULAR 150 X 320 MM
BLADE DIMENSION: 4.250 X 34 X 1,1 MM
SPEED: 18/100 M/MIN
WORKING HEIGHT: 845 MM
MOTOR: 2,2 KW
DIMENSIONS: 4.120 X 2.300 X 2.180 MM
WEIGHT: 1.900 KG



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land--machine in stock
-after reviewing the technical
-vg condition

-a well known reputable brand-weima

technical parameters:

-main engine power 37 kw
-engine power from the hydraulic pump 1.5 kw
-rotation 90 u/min

-automatic autorewers
-pull hydraulic

-the rotor length 1000 mm
-multiple staggered knife shaft set 23
-dimensions: 30 mm x 30 mm
-sieve fi 20 mm
-knives lace

-diameter suction fi 250
-rotor diameter 275 mm
-height of drawers foot 275 mm
-the length of the drawer pressure 800 mm

overall dimensions of the machine:

-length of 270 cm
width 230 cm
-height 200 cm
-weight 3000 kg

wood chipper can process a wide range of wood waste, which accumulate, for example. in industrial applications or carpentry workshops, saw mills or in the furniture industry. this list includes pallets and boxes, as well as long and short scrap of wood, veneer, chipboard, fibreboard, plywood and joiner's products, such as large furniture, window profiles, doors and stairs.

the main features of the machine:

* robust construction
* a reputable german brand weima
* the leader among manufacturers of chippers
the commendable
* for each professional

patented v rotor

-the optimum supply of material
-minimum cutter wear
– small power consumption at high performance
is a small gap between the rotor and blades kontruj?cymi
-defined issue knife

contoured v rotor is made of die-cast and placed on a stable bearings
on its perimeter welded are special grips knife in his pockets
in them are cutting knives and bolted
this enables fast replacement blades
thanks to this design during the shredding material screws are damaged
recessed cutting blades have 4 cutting edges, which can be 4 x turn,
providing precise cutting with high performance. -MACHINE IN STOCK -AFTER REVIEWING THE TECHNICAL -VG CONDITION -A WELL KNOWN REPUTABLE BRAND-WEIMA TECHNICAL PARAMETERS: -MAIN ENGINE POWER 37 KW -ENGINE POWER FROM THE HYDRAULIC PUMP 1.5 KW -ROTATION 90 U/MIN -AUTOMATIC AUTOREWERS -PULL HYDRAULIC -THE ROTOR LENGTH 1000 MM -MULTIPLE STAGGERED KNIFE SHAFT SET 23 -DIMENSIONS: 30 MM X 30 MM -SIEVE FI 20 MM -KNIVES LACE -DIAMETER SUCTION FI 250 -ROTOR DIAMETER 275 MM -HEIGHT OF DRAWERS FOOT 275 MM -THE LENGTH OF THE DRAWER PRESSURE 800 MM OVERALL DIMENSIONS OF THE MACHINE: -LENGTH OF 270 CM WIDTH 230 CM -HEIGHT 200 CM -WEIGHT 3000 KG WOOD CHIPPER CAN PROCESS A WIDE RANGE OF WOOD WASTE, WHICH ACCUMULATE, FOR EXAMPLE. IN INDUSTRIAL APPLICATIONS OR CARPENTRY WORKSHOPS, SAW MILLS OR IN THE FURNITURE INDUSTRY. THIS LIST INCLUDES PALLETS AND BOXES, AS WELL AS LONG AND SHORT SCRAP OF WOOD, VENEER, CHIPBOARD, FIBREBOARD, PLYWOOD AND JOINER'S PRODUCTS, SUCH AS LARGE FURNITURE, WINDOW PROFILES, DOORS AND STAIRS. THE MAIN FEATURES OF THE MACHINE: * ROBUST CONSTRUCTION * A REPUTABLE GERMAN BRAND WEIMA * THE LEADER AMONG MANUFACTURERS OF CHIPPERS THE COMMENDABLE * FOR EACH PROFESSIONAL PATENTED V ROTOR -THE OPTIMUM SUPPLY OF MATERIAL -MINIMUM CUTTER WEAR – SMALL POWER CONSUMPTION AT HIGH PERFORMANCE IS A SMALL GAP BETWEEN THE ROTOR AND BLADES KONTRUJ?CYMI -DEFINED ISSUE KNIFE CONTOURED V ROTOR IS MADE OF DIE-CAST AND PLACED ON A STABLE BEARINGS ON ITS PERIMETER WELDED ARE SPECIAL GRIPS KNIFE IN HIS POCKETS IN THEM ARE CUTTING KNIVES AND BOLTED THIS ENABLES FAST REPLACEMENT BLADES THANKS TO THIS DESIGN DURING THE SHREDDING MATERIAL SCREWS ARE DAMAGED RECESSED CUTTING BLADES HAVE 4 CUTTING EDGES, WHICH CAN BE 4 X TURN, PROVIDING PRECISE CUTTING WITH HIGH PERFORMANCE.
Vendedor: StanDrew
Año de construcción: usado
Ubicación: Land-: 5.320 x 34 x 1,1 mm<br/>: 844 mm<br/>: 3 kw<br/>: 2.870 x 1.895 x 2.300 mm<br/>: 2.100 kg<br/>semiautomatic hydraulic bandsaw<br/>strong electro-welded steel structure<br/>no vibrations during cutting<br/>mobile control console<br/>adjustable descent speed<br/>electronic inverter for variable speed<br/>suitable for cutting medium and big sizes of pipes, profiles and beams<br/><br/>cutting capacity:<br/>90°: round 510 mm <br/> square 480 mm <br/> rectangular 650 x 450 mm<br/>45° right: round 440 mm <br/> square 440 mm <br/> rectangular 440 x 440 mm<br/>60° right: round 250 mm <br/> square 250 mm <br/> rectangular 250 x 450 mm<br/>45° left: round 440 mm <br/> square 430 mm <br/> rectangular 430 x 430 mm<br/>60° left: round 250 mm <br/> square 250 mm <br/> rectangular 250 x 450 mm<br/>blade dimension: 5.320 x 34 x 1,1 mm<br/>speed: 15/100 m/min<br/>working height: 844 mm<br/>motor: 3 kw<br/>dimensions: 2.870 x 1.895 x 2.300 mm<br/>weight: 2.100 kg<br/><br/><br/><br/> : 5.320 X 34 X 1,1 MM
: 844 MM
: 3 KW
: 2.870 X 1.895 X 2.300 MM
: 2.100 KG
SEMIAUTOMATIC HYDRAULIC BANDSAW
STRONG ELECTRO-WELDED STEEL STRUCTURE
NO VIBRATIONS DURING CUTTING
MOBILE CONTROL CONSOLE
ADJUSTABLE DESCENT SPEED
ELECTRONIC INVERTER FOR VARIABLE SPEED
SUITABLE FOR CUTTING MEDIUM AND BIG SIZES OF PIPES, PROFILES AND BEAMS

CUTTING CAPACITY:
90°: ROUND 510 MM
SQUARE 480 MM
RECTANGULAR 650 X 450 MM
45° RIGHT: ROUND 440 MM
SQUARE 440 MM
RECTANGULAR 440 X 440 MM
60° RIGHT: ROUND 250 MM
SQUARE 250 MM
RECTANGULAR 250 X 450 MM
45° LEFT: ROUND 440 MM
SQUARE 430 MM
RECTANGULAR 430 X 430 MM
60° LEFT: ROUND 250 MM
SQUARE 250 MM
RECTANGULAR 250 X 450 MM
BLADE DIMENSION: 5.320 X 34 X 1,1 MM
SPEED: 15/100 M/MIN
WORKING HEIGHT: 844 MM
MOTOR: 3 KW
DIMENSIONS: 2.870 X 1.895 X 2.300 MM
WEIGHT: 2.100 KG



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land--machine in stock
-after reviewing the technical
-well-known brand weima

technical parameters:

-main motor power 18.5 kw
-engine power from the hydraulic pump 0, 75kw

-automatic autorewers
-pull hydraulic

-the rotor length 1000 mm
-rotation 90 u/min
-multiple staggered knife shaft set 23
-dimensions: 30 mm x 30 mm
-sieve fi 25 mm
-flat blades

-diameter suction fi 200 mm
-rotor diameter 185 mm
-the height of the drawer release 185 mm
-the length of the drawer pressure 850 mm

overall dimensions of the machine:

-length: 240 cm
-width: 160 cm
-height 180 cm

-weight of 1900 kg

wood chipper can process a wide range of wood waste, which accumulate, for example. in industrial applications or carpentry workshops, saw mills or in the furniture industry. this list includes pallets and boxes, as well as long and short scrap of wood, veneer, chipboard, fibreboard, plywood and joiner's products, such as large furniture, window profiles, doors and stairs.

the main features of the machine:

* robust construction
* a reputable german brand weima
* the leader among manufacturers of chippers
the commendable
* for each professional

patented v rotor

-the optimum supply of material
-minimum cutter wear
– small power consumption at high performance
is a small gap between the rotor and blades kontruj?cymi
-defined issue knife

contoured v rotor is made of die-cast and placed on a stable bearings
on its perimeter welded are special grips knife in his pockets
in them are cutting knives and bolted
this enables fast replacement blades
thanks to this design during the shredding material screws are damaged
recessed cutting blades have 4 cutting edges, which can be 4 x turn,
providing precise cutting with high performance. -MACHINE IN STOCK -AFTER REVIEWING THE TECHNICAL -WELL-KNOWN BRAND WEIMA TECHNICAL PARAMETERS: -MAIN MOTOR POWER 18.5 KW -ENGINE POWER FROM THE HYDRAULIC PUMP 0, 75KW -AUTOMATIC AUTOREWERS -PULL HYDRAULIC -THE ROTOR LENGTH 1000 MM -ROTATION 90 U/MIN -MULTIPLE STAGGERED KNIFE SHAFT SET 23 -DIMENSIONS: 30 MM X 30 MM -SIEVE FI 25 MM -FLAT BLADES -DIAMETER SUCTION FI 200 MM -ROTOR DIAMETER 185 MM -THE HEIGHT OF THE DRAWER RELEASE 185 MM -THE LENGTH OF THE DRAWER PRESSURE 850 MM OVERALL DIMENSIONS OF THE MACHINE: -LENGTH: 240 CM -WIDTH: 160 CM -HEIGHT 180 CM -WEIGHT OF 1900 KG WOOD CHIPPER CAN PROCESS A WIDE RANGE OF WOOD WASTE, WHICH ACCUMULATE, FOR EXAMPLE. IN INDUSTRIAL APPLICATIONS OR CARPENTRY WORKSHOPS, SAW MILLS OR IN THE FURNITURE INDUSTRY. THIS LIST INCLUDES PALLETS AND BOXES, AS WELL AS LONG AND SHORT SCRAP OF WOOD, VENEER, CHIPBOARD, FIBREBOARD, PLYWOOD AND JOINER'S PRODUCTS, SUCH AS LARGE FURNITURE, WINDOW PROFILES, DOORS AND STAIRS. THE MAIN FEATURES OF THE MACHINE: * ROBUST CONSTRUCTION * A REPUTABLE GERMAN BRAND WEIMA * THE LEADER AMONG MANUFACTURERS OF CHIPPERS THE COMMENDABLE * FOR EACH PROFESSIONAL PATENTED V ROTOR -THE OPTIMUM SUPPLY OF MATERIAL -MINIMUM CUTTER WEAR – SMALL POWER CONSUMPTION AT HIGH PERFORMANCE IS A SMALL GAP BETWEEN THE ROTOR AND BLADES KONTRUJ?CYMI -DEFINED ISSUE KNIFE CONTOURED V ROTOR IS MADE OF DIE-CAST AND PLACED ON A STABLE BEARINGS ON ITS PERIMETER WELDED ARE SPECIAL GRIPS KNIFE IN HIS POCKETS IN THEM ARE CUTTING KNIVES AND BOLTED THIS ENABLES FAST REPLACEMENT BLADES THANKS TO THIS DESIGN DURING THE SHREDDING MATERIAL SCREWS ARE DAMAGED RECESSED CUTTING BLADES HAVE 4 CUTTING EDGES, WHICH CAN BE 4 X TURN, PROVIDING PRECISE CUTTING WITH HIGH PERFORMANCE.
Vendedor: StanDrew
Año de construcción: usado
Precio: 3.400 €
Ubicación: Land-: 45 °<br/>: 45 °<br/>: 1,8/2,5 kw<br/>: 160 mm<br/>: 600 mm<br/>: 1.220 mm<br/>: 1.060 mm<br/>: 206 kg<br/>very robust construction suited to cut metal profiles and solids (steel with resistance up to 70 kg/mm²)<br/>vice with quick clamping device and additional clapming strip for reduced cuttinag burr<br/>reduction gear and clutch to save the gear and sawing blades<br/>coolant equiptment<br/>sawing blade protection<br/>material stop<br/>thermic and magnetic motor protection<br/>90° longitudinal cuts are possible thanks to the rotating vice<br/>users manual in german<br/><br/>(sawing blade not included)<br/><br/>options:<br/><br/>sawing balde for mild steel hss 350 x 2.5 x 32 mm 180z c  ? 134,-<br/><br/>base   ? 364,-<br/><br/><br/>saw blade dimensions: 350 x (2)2,5 x 32 mm<br/>mitre left: 45°<br/>mitre right: 45°<br/>speeds: 30/60 r/min<br/>motor: 1,8/2,5 kw<br/>cutting capacity 90°: round 125 mm, square 110 mm, rectangle 160 x 90 mm<br/>cutting capacity 45° right: round 105 mm, square 90 mm, rectangle 80 x 100 mm<br/>cutting capacity 45° left: round 70 mm, square 65 mm, rectangle 60 x 70 mm<br/>width of the opening: 160 mm<br/>width: 600 mm<br/>depth: 1.220 mm<br/>height: 1.060 mm<br/>weight: 206 kg<br/><br/><br/><br/> : 45 °
: 45 °
: 1,8/2,5 KW
: 160 MM
: 600 MM
: 1.220 MM
: 1.060 MM
: 206 KG
VERY ROBUST CONSTRUCTION SUITED TO CUT METAL PROFILES AND SOLIDS (STEEL WITH RESISTANCE UP TO 70 KG/MM²)
VICE WITH QUICK CLAMPING DEVICE AND ADDITIONAL CLAPMING STRIP FOR REDUCED CUTTINAG BURR
REDUCTION GEAR AND CLUTCH TO SAVE THE GEAR AND SAWING BLADES
COOLANT EQUIPTMENT
SAWING BLADE PROTECTION
MATERIAL STOP
THERMIC AND MAGNETIC MOTOR PROTECTION
90° LONGITUDINAL CUTS ARE POSSIBLE THANKS TO THE ROTATING VICE
USERS MANUAL IN GERMAN

(SAWING BLADE NOT INCLUDED)

OPTIONS:

SAWING BALDE FOR MILD STEEL HSS 350 X 2.5 X 32 MM 180Z C  ? 134,-

BASE   ? 364,-


SAW BLADE DIMENSIONS: 350 X (2)2,5 X 32 MM
MITRE LEFT: 45°
MITRE RIGHT: 45°
SPEEDS: 30/60 R/MIN
MOTOR: 1,8/2,5 KW
CUTTING CAPACITY 90°: ROUND 125 MM, SQUARE 110 MM, RECTANGLE 160 X 90 MM
CUTTING CAPACITY 45° RIGHT: ROUND 105 MM, SQUARE 90 MM, RECTANGLE 80 X 100 MM
CUTTING CAPACITY 45° LEFT: ROUND 70 MM, SQUARE 65 MM, RECTANGLE 60 X 70 MM
WIDTH OF THE OPENING: 160 MM
WIDTH: 600 MM
DEPTH: 1.220 MM
HEIGHT: 1.060 MM
WEIGHT: 206 KG



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land-machine specification

year: 2006 
control unit: mc 5 
robot: km lr 100-2212 

injection unit: .../380
screw diameter: 45 mm 
injection pressure: 1469 bar 
injection volume: 258 ccm 
shot capacity: 234,8 g 

clamping unit: 80/...
clamping force: 80 t 
platen size: 670 x 670 mm 
distance between tie bars: 420 x 420 mm 
mould height: 250 mm 
opening storke: 500 mm 
max.daylight: 750 mm 
ejector stroke: 150 mm 
drive power of the hydraulic pump: 15 kw 
general information:
delivery time: january 2019 
machine dimensions(m) lxwxh: 4,1 x 1,5 x 2,1 m 
weight: 6.400 kg 

equipment:
- bimetallic barrel
- incl. km robot MACHINE SPECIFICATION YEAR: 2006 CONTROL UNIT: MC 5 ROBOT: KM LR 100-2212 INJECTION UNIT: .../380 SCREW DIAMETER: 45 MM INJECTION PRESSURE: 1469 BAR INJECTION VOLUME: 258 CCM SHOT CAPACITY: 234,8 G CLAMPING UNIT: 80/... CLAMPING FORCE: 80 T PLATEN SIZE: 670 X 670 MM DISTANCE BETWEEN TIE BARS: 420 X 420 MM MOULD HEIGHT: 250 MM OPENING STORKE: 500 MM MAX.DAYLIGHT: 750 MM EJECTOR STROKE: 150 MM DRIVE POWER OF THE HYDRAULIC PUMP: 15 KW GENERAL INFORMATION: DELIVERY TIME: JANUARY 2019 MACHINE DIMENSIONS(M) LXWXH: 4,1 X 1,5 X 2,1 M WEIGHT: 6.400 KG EQUIPMENT: - BIMETALLIC BARREL - INCL. KM ROBOT
Vendedor: EuropNet GmbH
Año de construcción: usado
Ubicación: Land-: 2.765 x 27 x 0,9 mm<br/>: 870 mm<br/>: 1,5 kw<br/>: 2.300 x 1.830 x 1.600 mm<br/>: 1.000 kg<br/>automatic cnc bandsaw hydraulically driven<br/>graduated plate to identify different angles<br/>high blade tension to increase cutting accuracy and reduce cutting time<br/>up to 99 programmable cutting lenghts<br/>cnc driver with programming of all operations<br/>automatic calculation of blade thickness<br/>touch screen control<br/>suitable for cutting steel, cast iron and high-strength steels<br/><br/>cutting capacity:<br/>90°: round 255 mm <br/> square 230 mm <br/> rectangular 300 x 180 mm<br/>45° left: round 210 mm <br/> square 190 mm <br/> rectangular 200 x 160 mm<br/>60° left: round 135 mm <br/> square 110 mm <br/> rectangular 130 x 100 mm<br/>blade dimension: 2.765 x 27 x 0,9 mm<br/>speed: 18/100 m/min<br/>working height: 870 mm<br/>motor: 1,5 kw<br/>dimensions: 2.300 x 1.830 x 1.600 mm<br/>weight: 1.000 kg<br/><br/><br/><br/> : 2.765 X 27 X 0,9 MM
: 870 MM
: 1,5 KW
: 2.300 X 1.830 X 1.600 MM
: 1.000 KG
AUTOMATIC CNC BANDSAW HYDRAULICALLY DRIVEN
GRADUATED PLATE TO IDENTIFY DIFFERENT ANGLES
HIGH BLADE TENSION TO INCREASE CUTTING ACCURACY AND REDUCE CUTTING TIME
UP TO 99 PROGRAMMABLE CUTTING LENGHTS
CNC DRIVER WITH PROGRAMMING OF ALL OPERATIONS
AUTOMATIC CALCULATION OF BLADE THICKNESS
TOUCH SCREEN CONTROL
SUITABLE FOR CUTTING STEEL, CAST IRON AND HIGH-STRENGTH STEELS

CUTTING CAPACITY:
90°: ROUND 255 MM
SQUARE 230 MM
RECTANGULAR 300 X 180 MM
45° LEFT: ROUND 210 MM
SQUARE 190 MM
RECTANGULAR 200 X 160 MM
60° LEFT: ROUND 135 MM
SQUARE 110 MM
RECTANGULAR 130 X 100 MM
BLADE DIMENSION: 2.765 X 27 X 0,9 MM
SPEED: 18/100 M/MIN
WORKING HEIGHT: 870 MM
MOTOR: 1,5 KW
DIMENSIONS: 2.300 X 1.830 X 1.600 MM
WEIGHT: 1.000 KG



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land-tecnova twin screw extruder

3x degassing units
year 2014
suitable for pp and pe
loading hopper
dosing unit
bimetallic barrel
new screws, just replaced 128 mm diam. 42 l/d
counter- rotating movement
n.3 vacumm degassing units (n.2 vacuum pumps)
a.c. motor 355 kw (60% used in work)
constructed in 2014
complete with electric cabinet
average output 1.200 kg/h
(no screenchanger – no cutting – available separately)
manuals and drawings
excellent running conditions TECNOVA TWIN SCREW EXTRUDER 3X DEGASSING UNITS YEAR 2014 SUITABLE FOR PP AND PE LOADING HOPPER DOSING UNIT BIMETALLIC BARREL NEW SCREWS, JUST REPLACED 128 MM DIAM. 42 L/D COUNTER- ROTATING MOVEMENT N.3 VACUMM DEGASSING UNITS (N.2 VACUUM PUMPS) A.C. MOTOR 355 KW (60% USED IN WORK) CONSTRUCTED IN 2014 COMPLETE WITH ELECTRIC CABINET AVERAGE OUTPUT 1.200 KG/H (NO SCREENCHANGER – NO CUTTING – AVAILABLE SEPARATELY) MANUALS AND DRAWINGS EXCELLENT RUNNING CONDITIONS
Vendedor: GERMANPLAST SRL
Año de construcción: usado
Ubicación: Land-: 5.320 x 34 x 1,1 mm<br/>: 845 mm<br/>: 3 kw<br/>: 3.865 x 2.870 x 2.300 mm<br/>: 5.100 kg<br/>full automatic band saw<br/>integrated keyboard with cnc control<br/>large ram memory<br/>save over 300 cutting programs<br/>strong steel structure<br/>single-block gear motor<br/>no vibrations during cutting<br/>adjustable descent speed<br/>mobile control console<br/>electronic inverter for variable speed<br/>single stroke feeder<br/>automatic detection of material width<br/>roller table integrated<br/>10 inch lcd-touch screen<br/><br/>(photo shows model ktech 502 f2000)<br/><br/>cutting capacity:<br/>90°: round 510 mm <br/> square 480 mm <br/> rectangular 650 x 450 mm<br/>45° right: round 440 mm <br/> square 440 mm <br/> rectangular 440 x 440 mm<br/>60° right: round 250 mm <br/> square 250 mm <br/> rectangular 250 x 450 mm<br/>45° left: round 440 mm <br/> square 430 mm <br/> rectangular 430 x 430 mm<br/>60° left: round 250 mm <br/> square 250 mm <br/> rectangular 250 x 450 mm<br/>blade dimension: 5.320 x 34 x 1,1 mm<br/>speed: 18/100 m/min<br/>working height: 845 mm<br/>motor: 3 kw<br/>dimensions: 3.865 x 2.870 x 2.300 mm<br/>weight: 5.100 kg<br/><br/><br/><br/> : 5.320 X 34 X 1,1 MM
: 845 MM
: 3 KW
: 3.865 X 2.870 X 2.300 MM
: 5.100 KG
FULL AUTOMATIC BAND SAW
INTEGRATED KEYBOARD WITH CNC CONTROL
LARGE RAM MEMORY
SAVE OVER 300 CUTTING PROGRAMS
STRONG STEEL STRUCTURE
SINGLE-BLOCK GEAR MOTOR
NO VIBRATIONS DURING CUTTING
ADJUSTABLE DESCENT SPEED
MOBILE CONTROL CONSOLE
ELECTRONIC INVERTER FOR VARIABLE SPEED
SINGLE STROKE FEEDER
AUTOMATIC DETECTION OF MATERIAL WIDTH
ROLLER TABLE INTEGRATED
10 INCH LCD-TOUCH SCREEN

(PHOTO SHOWS MODEL KTECH 502 F2000)

CUTTING CAPACITY:
90°: ROUND 510 MM
SQUARE 480 MM
RECTANGULAR 650 X 450 MM
45° RIGHT: ROUND 440 MM
SQUARE 440 MM
RECTANGULAR 440 X 440 MM
60° RIGHT: ROUND 250 MM
SQUARE 250 MM
RECTANGULAR 250 X 450 MM
45° LEFT: ROUND 440 MM
SQUARE 430 MM
RECTANGULAR 430 X 430 MM
60° LEFT: ROUND 250 MM
SQUARE 250 MM
RECTANGULAR 250 X 450 MM
BLADE DIMENSION: 5.320 X 34 X 1,1 MM
SPEED: 18/100 M/MIN
WORKING HEIGHT: 845 MM
MOTOR: 3 KW
DIMENSIONS: 3.865 X 2.870 X 2.300 MM
WEIGHT: 5.100 KG



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land-new machine, ex factory in italia, incl. installation and putting into operation 

loading volume / capacity approx. 60m³ 
inside dimensions 10,60 x 5,80 x 4,10 m (lwh) 
outside dimensions 11,30 x 6,30 x 5,30 m (lwh) 
door 10,60 x 4,10 m  (lh)
size of the package 1,20 x 5,00 x 1,20 m (lwh) 

structure: aluminium + stainless steel 
isolation: aluminium + glass wool  100 mm + 40 
type of the door: sliding gate, hydraulical carriage 
door isolation glass wool 100 mm + 40 
feeding system: front loading 
ventilators: reversibel - on the roof, diameter 900 mm, 8 pieces of fans, el. nominal power 3 kw, air power 30.000 m³/h 
heating: heating registers bimetall: alu + stainless steel 
medium: hot water flow 95°c 
heating power at 60°c: 500 kw 
maximal drying temperature 75°c 
walk-through-door: yes, position: back wall 
wind pressure 70 kg / m² 
snow pressure: 150kg/m² (confirmable!) 
control system: venus 2500 automatic software, pc control inclusive 
pc: provided on site 
frequency converter 30 kw inclusive 
voltage / frequency 400v/50hz 

for more details and technical drawings see the pdf attached.
 NEW MACHINE, EX FACTORY IN ITALIA, INCL. INSTALLATION AND PUTTING INTO OPERATION LOADING VOLUME / CAPACITY APPROX. 60M³ INSIDE DIMENSIONS 10,60 X 5,80 X 4,10 M (LWH) OUTSIDE DIMENSIONS 11,30 X 6,30 X 5,30 M (LWH) DOOR 10,60 X 4,10 M (LH) SIZE OF THE PACKAGE 1,20 X 5,00 X 1,20 M (LWH) STRUCTURE: ALUMINIUM + STAINLESS STEEL ISOLATION: ALUMINIUM + GLASS WOOL 100 MM + 40 TYPE OF THE DOOR: SLIDING GATE, HYDRAULICAL CARRIAGE DOOR ISOLATION GLASS WOOL 100 MM + 40 FEEDING SYSTEM: FRONT LOADING VENTILATORS: REVERSIBEL - ON THE ROOF, DIAMETER 900 MM, 8 PIECES OF FANS, EL. NOMINAL POWER 3 KW, AIR POWER 30.000 M³/H HEATING: HEATING REGISTERS BIMETALL: ALU + STAINLESS STEEL MEDIUM: HOT WATER FLOW 95°C HEATING POWER AT 60°C: 500 KW MAXIMAL DRYING TEMPERATURE 75°C WALK-THROUGH-DOOR: YES, POSITION: BACK WALL WIND PRESSURE 70 KG / M² SNOW PRESSURE: 150KG/M² (CONFIRMABLE!) CONTROL SYSTEM: VENUS 2500 AUTOMATIC SOFTWARE, PC CONTROL INCLUSIVE PC: PROVIDED ON SITE FREQUENCY CONVERTER 30 KW INCLUSIVE VOLTAGE / FREQUENCY 400V/50HZ FOR MORE DETAILS AND TECHNICAL DRAWINGS SEE THE PDF ATTACHED.
Vendedor: Kauz Maschinenhandel GmbH
Año de construcción: usado
Precio: 20.400 €
Ubicación: Land-: 4.250 x 34 x 1,1 mm<br/>: 844 mm<br/>: 2,2 kw<br/>: 2.405 x 1.470 x 1.935 mm<br/>: 1.200 kg<br/>semiautomatic hydraulic bandsaw<br/>strong electro-welded steel structure<br/>no vibrations during cutting<br/>mobile control console<br/>adjustable descent speed<br/>electronic inverter for variable speed<br/>suitable for cutting medium and big sizes of pipes, profiles and beams<br/><br/>cutting capacity:<br/>90°: round 350 mm <br/> square 330 mm <br/> rectangular 500 x 310 mm<br/>45° right: round 320 mm <br/> square 320 mm <br/> rectangular 320 x 320 mm<br/>60° right: round 150 mm <br/> square 150 mm <br/> rectangular 150 x 320 mm<br/>45° left: round 300 mm <br/> square 300 mm <br/> rectangular 300 x 320 mm<br/>60° left: round 150 mm <br/> square 150 mm <br/> rectangular 150 x 320 mm<br/>blade dimension: 4.250 x 34 x 1,1 mm<br/>speed: 15/100 m/min<br/>working height: 844 mm<br/>motor: 2,2 kw<br/>dimensions: 2.405 x 1.470 x 1.935 mm<br/>weight: 1.200 kg<br/><br/><br/><br/> : 4.250 X 34 X 1,1 MM
: 844 MM
: 2,2 KW
: 2.405 X 1.470 X 1.935 MM
: 1.200 KG
SEMIAUTOMATIC HYDRAULIC BANDSAW
STRONG ELECTRO-WELDED STEEL STRUCTURE
NO VIBRATIONS DURING CUTTING
MOBILE CONTROL CONSOLE
ADJUSTABLE DESCENT SPEED
ELECTRONIC INVERTER FOR VARIABLE SPEED
SUITABLE FOR CUTTING MEDIUM AND BIG SIZES OF PIPES, PROFILES AND BEAMS

CUTTING CAPACITY:
90°: ROUND 350 MM
SQUARE 330 MM
RECTANGULAR 500 X 310 MM
45° RIGHT: ROUND 320 MM
SQUARE 320 MM
RECTANGULAR 320 X 320 MM
60° RIGHT: ROUND 150 MM
SQUARE 150 MM
RECTANGULAR 150 X 320 MM
45° LEFT: ROUND 300 MM
SQUARE 300 MM
RECTANGULAR 300 X 320 MM
60° LEFT: ROUND 150 MM
SQUARE 150 MM
RECTANGULAR 150 X 320 MM
BLADE DIMENSION: 4.250 X 34 X 1,1 MM
SPEED: 15/100 M/MIN
WORKING HEIGHT: 844 MM
MOTOR: 2,2 KW
DIMENSIONS: 2.405 X 1.470 X 1.935 MM
WEIGHT: 1.200 KG



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land-1. uniblok automatic model mlk-p 12/12/1 built from:
2. rai model rinsing machine with 12 nozzles
3. a filling system with 12 nozzles
4. a single head screwing plastic nuts
the pouring machine is equipped with:
1. system of sterilization of caps with uv rays
2. additional snail for the second bottle format
3. an i / o star and a central conveyor for an additional bottle format
4. mechanical nut feeder for the turning head
the pouring machine is adapted to 3 bottle formats and one nut type, fi 38 mm. the bottle on the inlet / outlet of the machine and during pouring is transported on the conveyor belt in a standing position.
- labeling machine for perimeter labels (fast line 35bb)
- sleeve labeling machine with a steam tunnel for shrinking labels (fast line 35n)
- videojet date patches
- automatic packaging line into filmat's lpa21 packages
- loading table with conveyors for the filling machine
- pouring machine with conveyors for a labeling device

the capacity of the line of 3,000 bottles per hour 1. UNIBLOK AUTOMATIC MODEL MLK-P 12/12/1 BUILT FROM: 2. RAI MODEL RINSING MACHINE WITH 12 NOZZLES 3. A FILLING SYSTEM WITH 12 NOZZLES 4. A SINGLE HEAD SCREWING PLASTIC NUTS THE POURING MACHINE IS EQUIPPED WITH: 1. SYSTEM OF STERILIZATION OF CAPS WITH UV RAYS 2. ADDITIONAL SNAIL FOR THE SECOND BOTTLE FORMAT 3. AN I / O STAR AND A CENTRAL CONVEYOR FOR AN ADDITIONAL BOTTLE FORMAT 4. MECHANICAL NUT FEEDER FOR THE TURNING HEAD THE POURING MACHINE IS ADAPTED TO 3 BOTTLE FORMATS AND ONE NUT TYPE, FI 38 MM. THE BOTTLE ON THE INLET / OUTLET OF THE MACHINE AND DURING POURING IS TRANSPORTED ON THE CONVEYOR BELT IN A STANDING POSITION. - LABELING MACHINE FOR PERIMETER LABELS (FAST LINE 35BB) - SLEEVE LABELING MACHINE WITH A STEAM TUNNEL FOR SHRINKING LABELS (FAST LINE 35N) - VIDEOJET DATE PATCHES - AUTOMATIC PACKAGING LINE INTO FILMAT'S LPA21 PACKAGES - LOADING TABLE WITH CONVEYORS FOR THE FILLING MACHINE - POURING MACHINE WITH CONVEYORS FOR A LABELING DEVICE THE CAPACITY OF THE LINE OF 3,000 BOTTLES PER HOUR
Vendedor: Biovesta
Año de construcción: usado
Precio: 3.290 €
Ubicación: Land-: 350 mm<br/>: 45 °<br/>: 45 °<br/>: 1,5/1,8 kw<br/>: 610 mm<br/>: 880 mm<br/>: 990 mm<br/>: 163 kg<br/>manual circular saw for aluminium<br/>stops at 0°, 15°, 30°, 45° left and right<br/>hand-wheel to lock the head on all angles, graduation engraved on the worktable<br/>pair of front vices with quick clamping, free to move alongside the worktable<br/>aluminium removable jaws<br/>sawing blade protection<br/>material stop<br/>coolant equiptment<br/>head return by springs<br/>users manual in german<br/><br/>(sawing blade not included)<br/><br/>options:<br/><br/>pneumatic vice (not retrofittable)  ? 478,-<br/><br/>2 pair v-chuck to cut tubes, max. Ø 90 mm  ? 385,-<br/><br/>saw blade hm-s.ge 350x3.2/2.6x32mm 108 z ftn  ? 179,-<br/><br/>base   ? 463,-<br/><br/><br/>saw blade diameter: 350<br/>mitre left: 45°<br/>mitre right: 45°<br/>speeds: 1.800/3.600 r/min<br/>motor: 1,5/1,8 kw<br/>cutting capacity 90°: round 120 mm, square 105 mm, rectangle 200 x 80 mm<br/>cutting capacity 45° right: round 115 mm, square 100 mm, rectangle 150 x 80 mm<br/>cutting capacity 45° left: round 115 mm, square 100 mm, rectangle 150 x 80 mm<br/>cutting capacity 45° inclined: round 65 mm, square 60 mm, rectangle 180 x 50 mm<br/>width: 610 mm<br/>depth: 880 mm<br/>height: 990 mm<br/>weight: 163 kg<br/><br/><br/><br/> : 350 MM
: 45 °
: 45 °
: 1,5/1,8 KW
: 610 MM
: 880 MM
: 990 MM
: 163 KG
MANUAL CIRCULAR SAW FOR ALUMINIUM
STOPS AT 0°, 15°, 30°, 45° LEFT AND RIGHT
HAND-WHEEL TO LOCK THE HEAD ON ALL ANGLES, GRADUATION ENGRAVED ON THE WORKTABLE
PAIR OF FRONT VICES WITH QUICK CLAMPING, FREE TO MOVE ALONGSIDE THE WORKTABLE
ALUMINIUM REMOVABLE JAWS
SAWING BLADE PROTECTION
MATERIAL STOP
COOLANT EQUIPTMENT
HEAD RETURN BY SPRINGS
USERS MANUAL IN GERMAN

(SAWING BLADE NOT INCLUDED)

OPTIONS:

PNEUMATIC VICE (NOT RETROFITTABLE)  ? 478,-

2 PAIR V-CHUCK TO CUT TUBES, MAX. Ø 90 MM  ? 385,-

SAW BLADE HM-S.GE 350X3.2/2.6X32MM 108 Z FTN  ? 179,-

BASE   ? 463,-


SAW BLADE DIAMETER: 350
MITRE LEFT: 45°
MITRE RIGHT: 45°
SPEEDS: 1.800/3.600 R/MIN
MOTOR: 1,5/1,8 KW
CUTTING CAPACITY 90°: ROUND 120 MM, SQUARE 105 MM, RECTANGLE 200 X 80 MM
CUTTING CAPACITY 45° RIGHT: ROUND 115 MM, SQUARE 100 MM, RECTANGLE 150 X 80 MM
CUTTING CAPACITY 45° LEFT: ROUND 115 MM, SQUARE 100 MM, RECTANGLE 150 X 80 MM
CUTTING CAPACITY 45° INCLINED: ROUND 65 MM, SQUARE 60 MM, RECTANGLE 180 X 50 MM
WIDTH: 610 MM
DEPTH: 880 MM
HEIGHT: 990 MM
WEIGHT: 163 KG



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land-300 tons tie-bar-less imm built in 2008 with cc 200 control, integrated engel robot erc 33/2-f, crane for mould fixing (2tons), 16 hot chanel, accumulator for fast injection and parallel movements. 2 core puller fix platen, flow meter, transport belt. plastizising screw bimetalic.

technical details	
daylight max	1.300 mm
min. mould hight	400 mm
year of building	2008
working hours	73506
injection pressure	1.616/2.053 bar
injection volumen	511 cm3
nominal capacity of pump motor	45 kw
travel opening	900 mm
screw diameter	55 mm
platen size	1.100 x 1.000 mm
clamping force	3.000 kn

300 TONS TIE-BAR-LESS IMM BUILT IN 2008 WITH CC 200 CONTROL, INTEGRATED ENGEL ROBOT ERC 33/2-F, CRANE FOR MOULD FIXING (2TONS), 16 HOT CHANEL, ACCUMULATOR FOR FAST INJECTION AND PARALLEL MOVEMENTS. 2 CORE PULLER FIX PLATEN, FLOW METER, TRANSPORT BELT. PLASTIZISING SCREW BIMETALIC. TECHNICAL DETAILS DAYLIGHT MAX 1.300 MM MIN. MOULD HIGHT 400 MM YEAR OF BUILDING 2008 WORKING HOURS 73506 INJECTION PRESSURE 1.616/2.053 BAR INJECTION VOLUMEN 511 CM3 NOMINAL CAPACITY OF PUMP MOTOR 45 KW TRAVEL OPENING 900 MM SCREW DIAMETER 55 MM PLATEN SIZE 1.100 X 1.000 MM CLAMPING FORCE 3.000 KN
Vendedor: Udo Krichbaum TRANSITUS, S.L.
Año de construcción: usado
Ubicación: Land-: 3.730 x 34 x 1,1 mm<br/>: 922 mm<br/>: 3 kw<br/>: 1.950 x 1.755 x 1.965 mm<br/>: 1.650 kg<br/>automatic hydraulic band saw<br/>strong steel structure<br/>cnc control for programming multiple lengths<br/>no vibrations and noise while cutting<br/>double vices before and after the blade<br/>position sensor automatically detects start-cut point<br/>pressure regulator for better clamping<br/>electrically driven feeder<br/>motorized metal brush for blade cleaning<br/>led integral lightning<br/>washing gun<br/>removable coolant tank<br/><br/><br/><br/><br/><br/>cutting capacity:<br/>90°: round 310 mm <br/> square 310 mm <br/> rectangular 340 x 310 mm<br/>blade dimension: 3.730 x 34 x 1,1 mm<br/>speed: 15/100 m/min<br/>working height: 922 mm<br/>motor: 3 kw<br/>dimensions: 1.950 x 1.755 x 1.965 mm<br/>weight: 1.650 kg<br/><br/><br/><br/> : 3.730 X 34 X 1,1 MM
: 922 MM
: 3 KW
: 1.950 X 1.755 X 1.965 MM
: 1.650 KG
AUTOMATIC HYDRAULIC BAND SAW
STRONG STEEL STRUCTURE
CNC CONTROL FOR PROGRAMMING MULTIPLE LENGTHS
NO VIBRATIONS AND NOISE WHILE CUTTING
DOUBLE VICES BEFORE AND AFTER THE BLADE
POSITION SENSOR AUTOMATICALLY DETECTS START-CUT POINT
PRESSURE REGULATOR FOR BETTER CLAMPING
ELECTRICALLY DRIVEN FEEDER
MOTORIZED METAL BRUSH FOR BLADE CLEANING
LED INTEGRAL LIGHTNING
WASHING GUN
REMOVABLE COOLANT TANK





CUTTING CAPACITY:
90°: ROUND 310 MM
SQUARE 310 MM
RECTANGULAR 340 X 310 MM
BLADE DIMENSION: 3.730 X 34 X 1,1 MM
SPEED: 15/100 M/MIN
WORKING HEIGHT: 922 MM
MOTOR: 3 KW
DIMENSIONS: 1.950 X 1.755 X 1.965 MM
WEIGHT: 1.650 KG



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land-machine specification

year: 1996 
control unit: mc3 f 

injection unit: .../390
screw diameter: 35 mm 
injection pressure: 2429 bar 
injection volume: 156 ccm 
shot capacity: 142 g 

clamping unit: km 125/...
clamping force: 125 t 
platen size: 745 x 770 mm 
distance between tie bars: 470 x 470 mm 
mould height: 300 mm 
opening storke: 600 mm 
max.daylight: 900 mm 
ejector stroke: 150 mm 
drive power of the hydraulic pump: 18,5 kw 
cylinder heating power: 11 kw 

general information:
delivery time: february 
machine dimensions(m) lxwxh: 4,5 x 1,3 x 2,2 m 
weight: 5.800 kg 

equipment:
- 1 x pneumatic valve
- 1 x core pull
- bimetallic barrel  MACHINE SPECIFICATION YEAR: 1996 CONTROL UNIT: MC3 F INJECTION UNIT: .../390 SCREW DIAMETER: 35 MM INJECTION PRESSURE: 2429 BAR INJECTION VOLUME: 156 CCM SHOT CAPACITY: 142 G CLAMPING UNIT: KM 125/... CLAMPING FORCE: 125 T PLATEN SIZE: 745 X 770 MM DISTANCE BETWEEN TIE BARS: 470 X 470 MM MOULD HEIGHT: 300 MM OPENING STORKE: 600 MM MAX.DAYLIGHT: 900 MM EJECTOR STROKE: 150 MM DRIVE POWER OF THE HYDRAULIC PUMP: 18,5 KW CYLINDER HEATING POWER: 11 KW GENERAL INFORMATION: DELIVERY TIME: FEBRUARY MACHINE DIMENSIONS(M) LXWXH: 4,5 X 1,3 X 2,2 M WEIGHT: 5.800 KG EQUIPMENT: - 1 X PNEUMATIC VALVE - 1 X CORE PULL - BIMETALLIC BARREL
Vendedor: EuropNet GmbH
Año de construcción: usado
Precio: 11.800 €
Ubicación: Land-: 4.020 x 34 x 1,1 mm<br/>: 940 mm<br/>: 1,5/2,2 kw<br/>: 1.787 x 1.530 x 2.240 mm<br/>: 680 kg<br/>semiautomatic hydraulic bandsaw for medium and heavy steelwork<br/>hydraulic vice with adjustable guides<br/>steel sawframe with integrated rotating table<br/>suitable for cutting steel and cast iron<br/>position sensor automatically detects start-cut point<br/>adjustable bar stop<br/>blade-cleaning brush<br/>removable chip collector<br/>coolant tank<br/><br/><br/><br/><br/><br/>cutting capacity:<br/>90°: round 310 mm <br/> square 280 mm <br/> rectangular 400 x 250 mm<br/>45° right: round 280 mm <br/> square 270 mm <br/> rectangular 300 x 220 mm<br/>45° left: round 280 mm <br/> square 270 mm <br/> rectangular 300 x 220 mm<br/>60° left: round 210 mm <br/> square 200 mm <br/> rectangular 200 x 200 mm<br/>blade dimension: 4.020 x 34 x 1,1 mm<br/>speed: 37/74 m/min<br/>working height: 940 mm<br/>motor: 1,5/2,2 kw<br/>dimensions: 1.787 x 1.530 x 2.240 mm<br/>weight: 680 kg<br/><br/><br/><br/> : 4.020 X 34 X 1,1 MM
: 940 MM
: 1,5/2,2 KW
: 1.787 X 1.530 X 2.240 MM
: 680 KG
SEMIAUTOMATIC HYDRAULIC BANDSAW FOR MEDIUM AND HEAVY STEELWORK
HYDRAULIC VICE WITH ADJUSTABLE GUIDES
STEEL SAWFRAME WITH INTEGRATED ROTATING TABLE
SUITABLE FOR CUTTING STEEL AND CAST IRON
POSITION SENSOR AUTOMATICALLY DETECTS START-CUT POINT
ADJUSTABLE BAR STOP
BLADE-CLEANING BRUSH
REMOVABLE CHIP COLLECTOR
COOLANT TANK





CUTTING CAPACITY:
90°: ROUND 310 MM
SQUARE 280 MM
RECTANGULAR 400 X 250 MM
45° RIGHT: ROUND 280 MM
SQUARE 270 MM
RECTANGULAR 300 X 220 MM
45° LEFT: ROUND 280 MM
SQUARE 270 MM
RECTANGULAR 300 X 220 MM
60° LEFT: ROUND 210 MM
SQUARE 200 MM
RECTANGULAR 200 X 200 MM
BLADE DIMENSION: 4.020 X 34 X 1,1 MM
SPEED: 37/74 M/MIN
WORKING HEIGHT: 940 MM
MOTOR: 1,5/2,2 KW
DIMENSIONS: 1.787 X 1.530 X 2.240 MM
WEIGHT: 680 KG



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land-code: 0536
brand: greda - italia
model: poker - ce standard 

flexible cnc machining center with 3 axis for multi-operations  - ce standard 
machining center with 3 axis for end-working operations : boring, tenoning, mortising, milling and end-cutting 

it is equipped with 5 working units: n° 1 end-cutting unit   - n° 1 shaping unit with right-hand rotation  - n° 1 shaping unit with left-hand rotation  - n° 2 multi-machining units for boring, mortising, tenoning and milling
technical data: 
axis x  max 1500 mm
axis y max 400 mm
axis z  max 220 mm
n° 2 stationary tables   - inclination  from 0 to  30°  with  n° 2 hold-down clamps  - n° 2 swivelling fences  - allow to work in a commuter cycle guaranteeyng quick and safe loading/unloading operations.  moreover, the working tables can be used together to machine big-sized pieces  
end cutting unit : blade motor  hp 3 - blade diameter  350 mm 
n° 2  shaping units : motor hp 5,5 - n° 2 shafts   right and left rotation  diameter 30 mm   - max  milling  diameter  160 mm - max milling height mm 100
multi-machining unit : n° 2 motors hp 5,5 - max rotation speed  18.000 rpm 
automatic 4-8 position  divisor . this rotating device allows to machine up to 8 piece faces in just one working cycle
power kw 15
pneumatic system  6 atm
perimeter protection nets 
numerical control  osai 110/10 - cpu master 64 bit 133 mhz - hard disk  2 gb - 8 mb dynamic  ram  - colour  screen  10 CODE: 0536 BRAND: GREDA - ITALIA MODEL: POKER - CE STANDARD FLEXIBLE CNC MACHINING CENTER WITH 3 AXIS FOR MULTI-OPERATIONS - CE STANDARD MACHINING CENTER WITH 3 AXIS FOR END-WORKING OPERATIONS : BORING, TENONING, MORTISING, MILLING AND END-CUTTING IT IS EQUIPPED WITH 5 WORKING UNITS: N° 1 END-CUTTING UNIT - N° 1 SHAPING UNIT WITH RIGHT-HAND ROTATION - N° 1 SHAPING UNIT WITH LEFT-HAND ROTATION - N° 2 MULTI-MACHINING UNITS FOR BORING, MORTISING, TENONING AND MILLING TECHNICAL DATA: AXIS X MAX 1500 MM AXIS Y MAX 400 MM AXIS Z MAX 220 MM N° 2 STATIONARY TABLES - INCLINATION FROM 0 TO 30° WITH N° 2 HOLD-DOWN CLAMPS - N° 2 SWIVELLING FENCES - ALLOW TO WORK IN A COMMUTER CYCLE GUARANTEEYNG QUICK AND SAFE LOADING/UNLOADING OPERATIONS. MOREOVER, THE WORKING TABLES CAN BE USED TOGETHER TO MACHINE BIG-SIZED PIECES END CUTTING UNIT : BLADE MOTOR HP 3 - BLADE DIAMETER 350 MM N° 2 SHAPING UNITS : MOTOR HP 5,5 - N° 2 SHAFTS RIGHT AND LEFT ROTATION DIAMETER 30 MM - MAX MILLING DIAMETER 160 MM - MAX MILLING HEIGHT MM 100 MULTI-MACHINING UNIT : N° 2 MOTORS HP 5,5 - MAX ROTATION SPEED 18.000 RPM AUTOMATIC 4-8 POSITION DIVISOR . THIS ROTATING DEVICE ALLOWS TO MACHINE UP TO 8 PIECE FACES IN JUST ONE WORKING CYCLE POWER KW 15 PNEUMATIC SYSTEM 6 ATM PERIMETER PROTECTION NETS NUMERICAL CONTROL OSAI 110/10 - CPU MASTER 64 BIT 133 MHZ - HARD DISK 2 GB - 8 MB DYNAMIC RAM - COLOUR SCREEN 10" - FLOPPY INTERFACES - VIDEOGRAPHIC PROGRAMME OVERALL DIMENSIONS : MM 2000 X 2000 X 1500 H WEIGHT KG 2500
Vendedor: TOMESANI Srl
Año de construcción: usado
Precio: 10.900 €
Ubicación: Land-: 3.370 x 27 x 0,9 mm<br/>: 940 mm<br/>: 1,5/1,8 kw<br/>: 1.750 x 1.480 x 1.900 mm<br/>: 649 kg<br/>hydraulic vice with adjustable guides<br/>steel sawframe<br/>adjustable blade tension<br/>suitable for cutting steel and cast iron<br/>position sensor automatically detects start-cut point<br/>adjustable bar stop<br/>blade-cleaning brush<br/>removable chip collector<br/>coolant tank<br/><br/><br/><br/><br/><br/>cutting capacity:<br/>90°: round 305 mm <br/> square 250 mm <br/> rectangular 350 x 200 mm<br/>45° right: round 250 mm <br/> square 230 mm <br/> rectangular 230 x 200 mm<br/>45° left: round 250 mm <br/> square 230 mm <br/> rectangular 230 x 200 mm<br/>60° left: round 175 mm <br/> square 155 mm <br/> rectangular 170 x 100 mm<br/>blade dimension: 3.370 x 27 x 0,9 mm<br/>speed: 37/74 m/min<br/>working height: 940 mm<br/>motor: 1,5/1,8 kw<br/>dimensions: 1.750 x 1.480 x 1.900 mm<br/>weight: 649 kg<br/><br/><br/><br/> : 3.370 X 27 X 0,9 MM
: 940 MM
: 1,5/1,8 KW
: 1.750 X 1.480 X 1.900 MM
: 649 KG
HYDRAULIC VICE WITH ADJUSTABLE GUIDES
STEEL SAWFRAME
ADJUSTABLE BLADE TENSION
SUITABLE FOR CUTTING STEEL AND CAST IRON
POSITION SENSOR AUTOMATICALLY DETECTS START-CUT POINT
ADJUSTABLE BAR STOP
BLADE-CLEANING BRUSH
REMOVABLE CHIP COLLECTOR
COOLANT TANK





CUTTING CAPACITY:
90°: ROUND 305 MM
SQUARE 250 MM
RECTANGULAR 350 X 200 MM
45° RIGHT: ROUND 250 MM
SQUARE 230 MM
RECTANGULAR 230 X 200 MM
45° LEFT: ROUND 250 MM
SQUARE 230 MM
RECTANGULAR 230 X 200 MM
60° LEFT: ROUND 175 MM
SQUARE 155 MM
RECTANGULAR 170 X 100 MM
BLADE DIMENSION: 3.370 X 27 X 0,9 MM
SPEED: 37/74 M/MIN
WORKING HEIGHT: 940 MM
MOTOR: 1,5/1,8 KW
DIMENSIONS: 1.750 X 1.480 X 1.900 MM
WEIGHT: 649 KG



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land-demag ergotech system 3500-840
year of construction: 2000

injection unit:
screw diameter: 45 mm
shot weight: 320 g
injection pressure: 2402 bar
dispensing volume: 358 cc

clamping unit:
clamping force: 350 t
tie bar distance: 720 x 650 mm
size of the clamping plates: 1040 x 950 mm
ejector: hydraulic
clamping unit: knee lever

control:
nc 4

additional equipment:
euromap
robot interface
hydraulic core pulling x 1
injection unit made of bimetal
parallel movements
central lubrication system
built-in printer to print out the machine history
auto tool installation height
it is possible to change the injection unit for a larger injection unit with screw diameter 50 mm, 60 mm,

dimensions:
: weight 13800
length/width/height: 6.5 x 2.0 x 2.3 m

drive:
pump/motor: 45 kw
heating power: 15 kw
cylinder heating: 60 kw

price: on request DEMAG ERGOTECH SYSTEM 3500-840 YEAR OF CONSTRUCTION: 2000 INJECTION UNIT: SCREW DIAMETER: 45 MM SHOT WEIGHT: 320 G INJECTION PRESSURE: 2402 BAR DISPENSING VOLUME: 358 CC CLAMPING UNIT: CLAMPING FORCE: 350 T TIE BAR DISTANCE: 720 X 650 MM SIZE OF THE CLAMPING PLATES: 1040 X 950 MM EJECTOR: HYDRAULIC CLAMPING UNIT: KNEE LEVER CONTROL: NC 4 ADDITIONAL EQUIPMENT: EUROMAP ROBOT INTERFACE HYDRAULIC CORE PULLING X 1 INJECTION UNIT MADE OF BIMETAL PARALLEL MOVEMENTS CENTRAL LUBRICATION SYSTEM BUILT-IN PRINTER TO PRINT OUT THE MACHINE HISTORY AUTO TOOL INSTALLATION HEIGHT IT IS POSSIBLE TO CHANGE THE INJECTION UNIT FOR A LARGER INJECTION UNIT WITH SCREW DIAMETER 50 MM, 60 MM, DIMENSIONS: : WEIGHT 13800 LENGTH/WIDTH/HEIGHT: 6.5 X 2.0 X 2.3 M DRIVE: PUMP/MOTOR: 45 KW HEATING POWER: 15 KW CYLINDER HEATING: 60 KW PRICE: ON REQUEST
Vendedor: Szczep-pol s.c.
Año de construcción: usado
Precio: 25.200 €
Ubicación: Land-: 40 mm<br/>: 6.000 mm<br/>: 600 kg<br/>: 180 mm<br/>the alrs 600 is a cnc controlled flat bar feeding and shearing system to be mounted on geka hydracrop 80 and hydracrop 110 dual cylinder ironworkers. this system is ideally designed for shearing desired lengths and quantities of flat bars up to 600x15 mm and 6 m length.<br/><br/><br/>the assembly consists of:<br/> drive roller with hydraulically controlled pinch roller. servo motor with linear encoder. b&,amp,r power control 500 10?user friendly touch screen control mounted in a control cabinet. positive hydraulic clamping.  fix guide rollers.  manually adjustable straight guide rollers.  6m roller bed conveyor.  electric cabinet   <br/> <br/> <br/>the work process is as follows: <br/> place      the flat bar on the rollers adjust      the lateral rollers to the width of the flat bar clamp      the material with the hydraulic hold down run      the program previously generated through geka´s line pro software. <br/>the      machine will automatically feed to length and automatically will shear<br/><br/><br/>b&,r pc based 10? touch screen control main features:<br/>the unit consists of an industrial type pc control mounted in a console.<br/>it incorporates a touch screen monitor with an intuitive and extremely user friendly interface <br/>developed by geka for ease of navigation through all stages of operation.<br/> b&,amp,r power panel 500 pc control intel® atom? architecture advance one axis control unit.  10? color touch screen xga resolution b&,amp,r 2 gb compact flash memory for data storage. usb front port  ethernet port for network connectivity easy and extremely user friendly interface developed by geka programming is made through line pro software developed by geka importing of dxf/dstv files run mode displays layout of the part as it is being punched or spotted  run, design, jog, configuration and alarm modes  speed percentage control of the ",x", axis via the touch screen potentiometer dial jog mode for calibration of axis, manual control of the axis forward and back, and go-to mode for manual shearing.  on-screen diagnostics of plc input/outputs as well as the x driver, for ease of troubleshooting the system.  set-up features include selections of multiple languages, inches or millimeters, type of machine, and ",x", min/max adjustments. <br/><br/>electric cabinet<br/> electric cabinet      containing power and control equipment for the axis positioning and      control of the machine includes      allen-bradley guarmaster® safety relays electric cabinet      is mounted in the same console as the control is located.  standard input      power is 400 v - 50 hz - 3 phases. in case different input requirement is      needed, let us know <br/> <br/> <br/>alrs 600 must be fitted on a factory built hydracrop 80 or hydracrop 110 machine<br/>the above price does not include hydracrop machine<br/><br/><br/><br/>option:<br/><br/>line pro software:<br/> offline license included to be installed in a pc  for  later on sending the files via the network or with  a usb stick to the machine it is a visual and a very easy to use application with graphic representations. it shows the operator the image of the piece that is being designed.  designing parts with a visual layout of the plate and shear pattern automatically optimizes the shearing sequence with the ability to also manually change the shear sequence. creates manufacturing sheets of the parts for hard copy printouts importing of dxf and dstv files available  according to designing specifications of the software. <br/> <br/> <br/><br/>max. dimension flat bar:<br/>hyd 80:   400 x 15 mm / 300 x 20 mm<br/>hyd 110: 600 x 15 mm / 400 x 20 mm<br/>min. width of flat bar: 40 mm<br/>max. length of flat bar: 6.000 mm<br/>max. weight of flat bar: 600 kg<br/>length of last non processable part: 180 mm<br/>traverse speed: 0 - 16 m/min<br/>positioning accuracy: 0,2 mm/m<br/>repeatability: 0,1 mm<br/><br/><br/><br/> : 40 MM
: 6.000 MM
: 600 KG
: 180 MM
THE ALRS 600 IS A CNC CONTROLLED FLAT BAR FEEDING AND SHEARING SYSTEM TO BE MOUNTED ON GEKA HYDRACROP 80 AND HYDRACROP 110 DUAL CYLINDER IRONWORKERS. THIS SYSTEM IS IDEALLY DESIGNED FOR SHEARING DESIRED LENGTHS AND QUANTITIES OF FLAT BARS UP TO 600X15 MM AND 6 M LENGTH.


THE ASSEMBLY CONSISTS OF:
DRIVE ROLLER WITH HYDRAULICALLY CONTROLLED PINCH ROLLER. SERVO MOTOR WITH LINEAR ENCODER. B&,AMP,R POWER CONTROL 500 10?USER FRIENDLY TOUCH SCREEN CONTROL MOUNTED IN A CONTROL CABINET. POSITIVE HYDRAULIC CLAMPING. FIX GUIDE ROLLERS. MANUALLY ADJUSTABLE STRAIGHT GUIDE ROLLERS. 6M ROLLER BED CONVEYOR. ELECTRIC CABINET


THE WORK PROCESS IS AS FOLLOWS:
PLACE THE FLAT BAR ON THE ROLLERS ADJUST THE LATERAL ROLLERS TO THE WIDTH OF THE FLAT BAR CLAMP THE MATERIAL WITH THE HYDRAULIC HOLD DOWN RUN THE PROGRAM PREVIOUSLY GENERATED THROUGH GEKA´S LINE PRO SOFTWARE.
THE MACHINE WILL AUTOMATICALLY FEED TO LENGTH AND AUTOMATICALLY WILL SHEAR


B&,R PC BASED 10? TOUCH SCREEN CONTROL MAIN FEATURES:
THE UNIT CONSISTS OF AN INDUSTRIAL TYPE PC CONTROL MOUNTED IN A CONSOLE.
IT INCORPORATES A TOUCH SCREEN MONITOR WITH AN INTUITIVE AND EXTREMELY USER FRIENDLY INTERFACE
DEVELOPED BY GEKA FOR EASE OF NAVIGATION THROUGH ALL STAGES OF OPERATION.
B&,AMP,R POWER PANEL 500 PC CONTROL INTEL® ATOM? ARCHITECTURE ADVANCE ONE AXIS CONTROL UNIT. 10? COLOR TOUCH SCREEN XGA RESOLUTION B&,AMP,R 2 GB COMPACT FLASH MEMORY FOR DATA STORAGE. USB FRONT PORT ETHERNET PORT FOR NETWORK CONNECTIVITY EASY AND EXTREMELY USER FRIENDLY INTERFACE DEVELOPED BY GEKA PROGRAMMING IS MADE THROUGH LINE PRO SOFTWARE DEVELOPED BY GEKA IMPORTING OF DXF/DSTV FILES RUN MODE DISPLAYS LAYOUT OF THE PART AS IT IS BEING PUNCHED OR SPOTTED RUN, DESIGN, JOG, CONFIGURATION AND ALARM MODES SPEED PERCENTAGE CONTROL OF THE ",X", AXIS VIA THE TOUCH SCREEN POTENTIOMETER DIAL JOG MODE FOR CALIBRATION OF AXIS, MANUAL CONTROL OF THE AXIS FORWARD AND BACK, AND GO-TO MODE FOR MANUAL SHEARING. ON-SCREEN DIAGNOSTICS OF PLC INPUT/OUTPUTS AS WELL AS THE X DRIVER, FOR EASE OF TROUBLESHOOTING THE SYSTEM. SET-UP FEATURES INCLUDE SELECTIONS OF MULTIPLE LANGUAGES, INCHES OR MILLIMETERS, TYPE OF MACHINE, AND ",X", MIN/MAX ADJUSTMENTS.

ELECTRIC CABINET
ELECTRIC CABINET CONTAINING POWER AND CONTROL EQUIPMENT FOR THE AXIS POSITIONING AND CONTROL OF THE MACHINE INCLUDES ALLEN-BRADLEY GUARMASTER® SAFETY RELAYS ELECTRIC CABINET IS MOUNTED IN THE SAME CONSOLE AS THE CONTROL IS LOCATED. STANDARD INPUT POWER IS 400 V - 50 HZ - 3 PHASES. IN CASE DIFFERENT INPUT REQUIREMENT IS NEEDED, LET US KNOW
 

ALRS 600 MUST BE FITTED ON A FACTORY BUILT HYDRACROP 80 OR HYDRACROP 110 MACHINE
THE ABOVE PRICE DOES NOT INCLUDE HYDRACROP MACHINE



OPTION:

LINE PRO SOFTWARE:
OFFLINE LICENSE INCLUDED TO BE INSTALLED IN A PC  FOR LATER ON SENDING THE FILES VIA THE NETWORK OR WITH A USB STICK TO THE MACHINE IT IS A VISUAL AND A VERY EASY TO USE APPLICATION WITH GRAPHIC REPRESENTATIONS. IT SHOWS THE OPERATOR THE IMAGE OF THE PIECE THAT IS BEING DESIGNED. DESIGNING PARTS WITH A VISUAL LAYOUT OF THE PLATE AND SHEAR PATTERN AUTOMATICALLY OPTIMIZES THE SHEARING SEQUENCE WITH THE ABILITY TO ALSO MANUALLY CHANGE THE SHEAR SEQUENCE. CREATES MANUFACTURING SHEETS OF THE PARTS FOR HARD COPY PRINTOUTS IMPORTING OF DXF AND DSTV FILES AVAILABLE  ACCORDING TO DESIGNING SPECIFICATIONS OF THE SOFTWARE.
 


MAX. DIMENSION FLAT BAR:
HYD 80: 400 X 15 MM / 300 X 20 MM
HYD 110: 600 X 15 MM / 400 X 20 MM
MIN. WIDTH OF FLAT BAR: 40 MM
MAX. LENGTH OF FLAT BAR: 6.000 MM
MAX. WEIGHT OF FLAT BAR: 600 KG
LENGTH OF LAST NON PROCESSABLE PART: 180 MM
TRAVERSE SPEED: 0 - 16 M/MIN
POSITIONING ACCURACY: 0,2 MM/M
REPEATABILITY: 0,1 MM



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land-lwb steinl vcrs-t 300/36 t / maker as new
year of construction: 2006

injection unit:
dispensing volume: 36 cc

clamping unit:
clamping force: 30 t
ejector: hydraulic
clamping unit: hydraulic

control: lwb eco

additional equipment:
hydraulic core pulling x 1
control air valve
the injection unit is made of bimetal

dimensions:
weight: 3000 kg

price: on request LWB STEINL VCRS-T 300/36 T / MAKER AS NEW YEAR OF CONSTRUCTION: 2006 INJECTION UNIT: DISPENSING VOLUME: 36 CC CLAMPING UNIT: CLAMPING FORCE: 30 T EJECTOR: HYDRAULIC CLAMPING UNIT: HYDRAULIC CONTROL: LWB ECO ADDITIONAL EQUIPMENT: HYDRAULIC CORE PULLING X 1 CONTROL AIR VALVE THE INJECTION UNIT IS MADE OF BIMETAL DIMENSIONS: WEIGHT: 3000 KG PRICE: ON REQUEST
Vendedor: Szczep-pol s.c.
Año de construcción: usado
Precio: 5.400 €
Ubicación: Land-: 60 °<br/>: 45 °<br/>: 1,5/2,2 kw<br/>: 180 mm<br/>: 810 mm<br/>: 1.020 mm<br/>: 1.850 mm<br/>: 390 kg<br/>circular saw to also cut high strength steels<br/>linear guide of sawinghead with manual feed by hand lever<br/>manual machine vice, movable sideways with additional clapming strip for reduced cuttinag burr<br/>coolant equiptment<br/>sawing blade protection<br/>material stop<br/>extractable chip drawer<br/>chip brush<br/>stops at 0° and 45° left and right<br/>thermic motor protection<br/>users manual in german<br/><br/>(sawing blade not included)<br/><br/>option:<br/><br/>sawing balde for mild steel hss 370 x 3.0 x 40 mm 180z c  ? 175,-<br/><br/><br/>sawing blade dimensions: 370 x 3,0 x 40 mm<br/>mitre left: 60°<br/>mitre right: 45°<br/>speeds: 15/30 r/min<br/>motor: 1,5/2,2 kw<br/>cutting capacity 90°: round 120 mm, square 100 mm, rectangle 180 x 100 mm<br/>cutting capacity 45° right: round 120 mm, square 100 mm, rectangle 130 x 100 mm<br/>cutting capacity 60° right: round 110 mm, square 90 mm, rectangle 90 x 100 mm<br/>cutting capacity 45° left: round 105 mm, square 100 mm, rectangle 130 x 100 mm<br/>width of the opening: 180 mm<br/>width: 810 mm<br/>depth: 1.020 mm<br/>height: 1.850 mm<br/>weight: 390 kg<br/><br/><br/><br/> : 60 °
: 45 °
: 1,5/2,2 KW
: 180 MM
: 810 MM
: 1.020 MM
: 1.850 MM
: 390 KG
CIRCULAR SAW TO ALSO CUT HIGH STRENGTH STEELS
LINEAR GUIDE OF SAWINGHEAD WITH MANUAL FEED BY HAND LEVER
MANUAL MACHINE VICE, MOVABLE SIDEWAYS WITH ADDITIONAL CLAPMING STRIP FOR REDUCED CUTTINAG BURR
COOLANT EQUIPTMENT
SAWING BLADE PROTECTION
MATERIAL STOP
EXTRACTABLE CHIP DRAWER
CHIP BRUSH
STOPS AT 0° AND 45° LEFT AND RIGHT
THERMIC MOTOR PROTECTION
USERS MANUAL IN GERMAN

(SAWING BLADE NOT INCLUDED)

OPTION:

SAWING BALDE FOR MILD STEEL HSS 370 X 3.0 X 40 MM 180Z C  ? 175,-


SAWING BLADE DIMENSIONS: 370 X 3,0 X 40 MM
MITRE LEFT: 60°
MITRE RIGHT: 45°
SPEEDS: 15/30 R/MIN
MOTOR: 1,5/2,2 KW
CUTTING CAPACITY 90°: ROUND 120 MM, SQUARE 100 MM, RECTANGLE 180 X 100 MM
CUTTING CAPACITY 45° RIGHT: ROUND 120 MM, SQUARE 100 MM, RECTANGLE 130 X 100 MM
CUTTING CAPACITY 60° RIGHT: ROUND 110 MM, SQUARE 90 MM, RECTANGLE 90 X 100 MM
CUTTING CAPACITY 45° LEFT: ROUND 105 MM, SQUARE 100 MM, RECTANGLE 130 X 100 MM
WIDTH OF THE OPENING: 180 MM
WIDTH: 810 MM
DEPTH: 1.020 MM
HEIGHT: 1.850 MM
WEIGHT: 390 KG



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land-manroland directdrive
pile board feeder with side edge control
doublesheet control electric/mechanical
ultrasonic detection system
cardboard guide at sidelay
doublesize impression cylinder
enhanced cylinder surface
double sized transfer  cylinder
apl fully automated plate changing
rci ink and register remote control
automatic ink roller cleaning device
automatic blanket cleaning device
quickchange surface
roland deltamatic dampening
tecnotrans combi dampening and inktemperature control
with alcohol metering device, alcocontrol
sheet decurler
powder sprayer weko ap 262
pile board delivery
telepresence remote
becker variaair-system
automatic impression cylinder wash-up device
inline doublecoater (double-coater module with chamber-blade technology)
quickchange coating
roland selectdryer ir/tl
extended delivery approx. 1.828 mm
eltex antistatic at feeder and delivery
coater temperatur control equipment
ir / tl / uv drying system, consisting of
- uv preparation of the machine
- 3 x uv intermediate dryer (with full flexibility)
-ir / tl / -intermediate dryer in the tt module
-ir / tluv end dryer
inlinesorter
inline inspector (eagleeye)
powder extraction
colorpilot d + f - densitometry and colorimetry - color measurement and control system
heat exchanger water / water to uv end dryer

just completely overhauled in 2018, can be seen in production in printingshop, europe
   MANROLAND DIRECTDRIVE PILE BOARD FEEDER WITH SIDE EDGE CONTROL DOUBLESHEET CONTROL ELECTRIC/MECHANICAL ULTRASONIC DETECTION SYSTEM CARDBOARD GUIDE AT SIDELAY DOUBLESIZE IMPRESSION CYLINDER ENHANCED CYLINDER SURFACE DOUBLE SIZED TRANSFER CYLINDER APL FULLY AUTOMATED PLATE CHANGING RCI INK AND REGISTER REMOTE CONTROL AUTOMATIC INK ROLLER CLEANING DEVICE AUTOMATIC BLANKET CLEANING DEVICE QUICKCHANGE SURFACE ROLAND DELTAMATIC DAMPENING TECNOTRANS COMBI DAMPENING AND INKTEMPERATURE CONTROL WITH ALCOHOL METERING DEVICE, ALCOCONTROL SHEET DECURLER POWDER SPRAYER WEKO AP 262 PILE BOARD DELIVERY TELEPRESENCE REMOTE BECKER VARIAAIR-SYSTEM AUTOMATIC IMPRESSION CYLINDER WASH-UP DEVICE INLINE DOUBLECOATER (DOUBLE-COATER MODULE WITH CHAMBER-BLADE TECHNOLOGY) QUICKCHANGE COATING ROLAND SELECTDRYER IR/TL EXTENDED DELIVERY APPROX. 1.828 MM ELTEX ANTISTATIC AT FEEDER AND DELIVERY COATER TEMPERATUR CONTROL EQUIPMENT IR / TL / UV DRYING SYSTEM, CONSISTING OF - UV PREPARATION OF THE MACHINE - 3 X UV INTERMEDIATE DRYER (WITH FULL FLEXIBILITY) -IR / TL / -INTERMEDIATE DRYER IN THE TT MODULE -IR / TLUV END DRYER INLINESORTER INLINE INSPECTOR (EAGLEEYE) POWDER EXTRACTION COLORPILOT D + F - DENSITOMETRY AND COLORIMETRY - COLOR MEASUREMENT AND CONTROL SYSTEM HEAT EXCHANGER WATER / WATER TO UV END DRYER JUST COMPLETELY OVERHAULED IN 2018, CAN BE SEEN IN PRODUCTION IN PRINTINGSHOP, EUROPE
Vendedor: TMP Meurer Industry & Consult GmbH
Año de construcción: usado
Ubicación: Land-: 5.900 x 41 x 1,3 mm<br/>: 877,5 mm<br/>: 5,5 kw<br/>: 2.800 x 1.794 x 2.210 mm<br/>: 3.500 kg<br/>full automatic band saw<br/>tct band saw blades<br/>various cutting options and settings<br/>device for checking accuracy and to adjust the sawframe<br/>adjustable descent speed<br/>electric chip conveyor<br/>10 inch touch screen<br/>suitable for cutting steel, cast iron, high-strength steels and alloys<br/><br/><br/><br/><br/><br/>cutting capacity:<br/>90°: round 360 mm <br/> square 360 mm <br/> rectangular 360 x 350 mm (optional)<br/>blade dimension: 5.900 x 41 x 1,3 mm<br/>speed: 15/150 m/min<br/>working height: 877,5 mm<br/>motor: 5,5 kw<br/>dimensions: 2.800 x 1.794 x 2.210 mm<br/>weight: 3.500 kg<br/><br/><br/><br/> : 5.900 X 41 X 1,3 MM
: 877,5 MM
: 5,5 KW
: 2.800 X 1.794 X 2.210 MM
: 3.500 KG
FULL AUTOMATIC BAND SAW
TCT BAND SAW BLADES
VARIOUS CUTTING OPTIONS AND SETTINGS
DEVICE FOR CHECKING ACCURACY AND TO ADJUST THE SAWFRAME
ADJUSTABLE DESCENT SPEED
ELECTRIC CHIP CONVEYOR
10 INCH TOUCH SCREEN
SUITABLE FOR CUTTING STEEL, CAST IRON, HIGH-STRENGTH STEELS AND ALLOYS





CUTTING CAPACITY:
90°: ROUND 360 MM
SQUARE 360 MM
RECTANGULAR 360 X 350 MM (OPTIONAL)
BLADE DIMENSION: 5.900 X 41 X 1,3 MM
SPEED: 15/150 M/MIN
WORKING HEIGHT: 877,5 MM
MOTOR: 5,5 KW
DIMENSIONS: 2.800 X 1.794 X 2.210 MM
WEIGHT: 3.500 KG



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land-manufacturer: battenfeld
type: ba1500-630 cdc
year of construction: 1997
steuerungr: unilog 4000
clamping force: 1500 kn
tie bar distance: 500 x 500 mm
plate size: 740 x 740 mm
wz installation height: min 250
opening stroke: 650 mm
plate distance max: 900 mm
snail: 40 mm
displacement: 226 cm3 / 205.8 gram ps
injection pressure: 2707 bar

general
motor: kw 36
heating: 12 kw
size: 5 m x 1.5 m x 2 m
weight: 9000 kg

additional equipment
euromap
bimetal
core move x 2 MANUFACTURER: BATTENFELD TYPE: BA1500-630 CDC YEAR OF CONSTRUCTION: 1997 STEUERUNGR: UNILOG 4000 CLAMPING FORCE: 1500 KN TIE BAR DISTANCE: 500 X 500 MM PLATE SIZE: 740 X 740 MM WZ INSTALLATION HEIGHT: MIN 250 OPENING STROKE: 650 MM PLATE DISTANCE MAX: 900 MM SNAIL: 40 MM DISPLACEMENT: 226 CM3 / 205.8 GRAM PS INJECTION PRESSURE: 2707 BAR GENERAL MOTOR: KW 36 HEATING: 12 KW SIZE: 5 M X 1.5 M X 2 M WEIGHT: 9000 KG ADDITIONAL EQUIPMENT EUROMAP BIMETAL CORE MOVE X 2
Vendedor: PaGaPlast
Año de construcción: usado
Precio: 21.360 €
Ubicación: Land-: 3.370 x 27 x 0,9 mm<br/>: 880 mm<br/>: 1,8 kw<br/>: 1.900 x 1.850 x 1.990 mm<br/>: 890 kg<br/>automatic cnc bandsaw hydraulically driven<br/>fixed hydraulic vice with pressure reducer<br/>anti-burr hydraulic vertical vice<br/>adjustable blade tension<br/>up to 99 programmable cutting lengths<br/>cnc driver with programming of all operations<br/>suitable for cutting steel, cast iron and high-strength steels<br/>position sensor automatically detects start-cut point<br/>automatic calculation of blade thickness<br/>electronic inverter for variable blade speed<br/>blade-cleaning brush<br/>removable chip collector<br/>coolant tank<br/><br/><br/><br/><br/><br/>cutting capacity:<br/>90°: round 305 mm <br/> square 250 mm <br/> rectangular 350 x 200 mm<br/>45°: round 250 mm <br/> square 230 mm <br/> rectangular 230 x 200 mm<br/>60°: round 175 mm <br/> square 155 mm <br/> rectangular 170 x 100 mm<br/>blade dimension: 3.370 x 27 x 0,9 mm<br/>speed: 18/100 m/min<br/>working height: 880 mm<br/>motor: 1,8 kw<br/>dimensions: 1.900 x 1.850 x 1.990 mm<br/>weight: 890 kg<br/><br/><br/><br/> : 3.370 X 27 X 0,9 MM
: 880 MM
: 1,8 KW
: 1.900 X 1.850 X 1.990 MM
: 890 KG
AUTOMATIC CNC BANDSAW HYDRAULICALLY DRIVEN
FIXED HYDRAULIC VICE WITH PRESSURE REDUCER
ANTI-BURR HYDRAULIC VERTICAL VICE
ADJUSTABLE BLADE TENSION
UP TO 99 PROGRAMMABLE CUTTING LENGTHS
CNC DRIVER WITH PROGRAMMING OF ALL OPERATIONS
SUITABLE FOR CUTTING STEEL, CAST IRON AND HIGH-STRENGTH STEELS
POSITION SENSOR AUTOMATICALLY DETECTS START-CUT POINT
AUTOMATIC CALCULATION OF BLADE THICKNESS
ELECTRONIC INVERTER FOR VARIABLE BLADE SPEED
BLADE-CLEANING BRUSH
REMOVABLE CHIP COLLECTOR
COOLANT TANK





CUTTING CAPACITY:
90°: ROUND 305 MM
SQUARE 250 MM
RECTANGULAR 350 X 200 MM
45°: ROUND 250 MM
SQUARE 230 MM
RECTANGULAR 230 X 200 MM
60°: ROUND 175 MM
SQUARE 155 MM
RECTANGULAR 170 X 100 MM
BLADE DIMENSION: 3.370 X 27 X 0,9 MM
SPEED: 18/100 M/MIN
WORKING HEIGHT: 880 MM
MOTOR: 1,8 KW
DIMENSIONS: 1.900 X 1.850 X 1.990 MM
WEIGHT: 890 KG



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land-there are five dosing units available, 3x gk 300 and 2x gk 150, output gk 300/ 150: 300/ 150kg/h, year of construction gk 300/ 150: 2010/ 2009, machines are packed into boxes.  THERE ARE FIVE DOSING UNITS AVAILABLE, 3X GK 300 AND 2X GK 150, OUTPUT GK 300/ 150: 300/ 150KG/H, YEAR OF CONSTRUCTION GK 300/ 150: 2010/ 2009, MACHINES ARE PACKED INTO BOXES.
Vendedor: Innovac GmbH
Año de construcción: usado
Precio: 2.200 €
Ubicación: Land-: 45 °<br/>: 45 °<br/>: 1,5/2 kw<br/>: 160 mm<br/>: 500 mm<br/>: 1.050 mm<br/>: 990 mm<br/>: 135 kg<br/>vice with quick clamping device and additional clapming strip for reduced cuttinag burr<br/>reduction gear and clutch to save the gear and sawing blades<br/>coolant equiptment<br/>sawing blade protection<br/>material stop<br/>users manual in german<br/><br/>(sawing blade not included)<br/><br/>options:<br/><br/>sawing balde for mild steel hss 300 x 2.5 x 32 mm 180z c  ? 94,-<br/><br/>base   ? 322,-<br/><br/><br/>saw blade dimensions: 300 x (2)2,5 x 32 mm<br/>mitre left: 45°<br/>mitre right: 45°<br/>speeds: 33/66 r/min<br/>motor: 1,5/2 kw<br/>cutting capacity 90°: round 102 mm, square 90 mm, rectangle 120 x 80 mm<br/>cutting capacity 45° right: round 90 mm, square 80 mm, rectangle 90 x 70 mm<br/>cutting capacity 45° left: round 80 mm, square 70 mm, rectangle 85 x 70 mm<br/>width of the opening: 160 mm<br/>width: 500 mm<br/>depth: 1.050 mm<br/>height: 990 mm<br/>weight: 135 kg<br/><br/><br/><br/> : 45 °
: 45 °
: 1,5/2 KW
: 160 MM
: 500 MM
: 1.050 MM
: 990 MM
: 135 KG
VICE WITH QUICK CLAMPING DEVICE AND ADDITIONAL CLAPMING STRIP FOR REDUCED CUTTINAG BURR
REDUCTION GEAR AND CLUTCH TO SAVE THE GEAR AND SAWING BLADES
COOLANT EQUIPTMENT
SAWING BLADE PROTECTION
MATERIAL STOP
USERS MANUAL IN GERMAN

(SAWING BLADE NOT INCLUDED)

OPTIONS:

SAWING BALDE FOR MILD STEEL HSS 300 X 2.5 X 32 MM 180Z C  ? 94,-

BASE   ? 322,-


SAW BLADE DIMENSIONS: 300 X (2)2,5 X 32 MM
MITRE LEFT: 45°
MITRE RIGHT: 45°
SPEEDS: 33/66 R/MIN
MOTOR: 1,5/2 KW
CUTTING CAPACITY 90°: ROUND 102 MM, SQUARE 90 MM, RECTANGLE 120 X 80 MM
CUTTING CAPACITY 45° RIGHT: ROUND 90 MM, SQUARE 80 MM, RECTANGLE 90 X 70 MM
CUTTING CAPACITY 45° LEFT: ROUND 80 MM, SQUARE 70 MM, RECTANGLE 85 X 70 MM
WIDTH OF THE OPENING: 160 MM
WIDTH: 500 MM
DEPTH: 1.050 MM
HEIGHT: 990 MM
WEIGHT: 135 KG



Vendedor: HESSE+CO GesmbH
Usted no ha encontrado su máquina deseada? enviar consulta a todos los distribuidores (no hay registro necesario)
more IMET types: