700 ofertas

Año de construcción: usado
Ubicación: Land-powder coating equipment

 parkerizing phosphate coating equipment
make:wastec(korean)
year:2014
2) process tank 
? load/unload(#1):size: 800(w) x 1,200(l) x 1,200(h)mm 
? alkali cleaner tank(#2) : size: 800(w) x 1,200(l) x 1,200(h)mm
3) 2-step water rinse bath(#3,4): size: 1,400(w) x 1,200(l) x 1,200(h)mm
4) acid rinse bath(#5): size: 750(w) x 1,200(l) x  1,200(h)mm
5) 2-step water rinse bath(#6,7): 1,400(w) x 1,200(l) x  1,200(h)mm
7) surface condition bath(#8) :: 750(w) x 1,200(l) 1,200(h)mm
8) coating bath(#9,10) : 900(w) x 1,200(l) x 1,200(h)mm
9) hot water rinse(#11) : 750(w) x 1,200(l) x 1,200(h)mm
10) dry tank(#12) :  
 size(inside): 700(w) x   1,200(l) x 1,200(h)mm
    size(outside): 1,300(w) x  2,000(l) x 1,200(h)mm  
  temp: 90?~110?
11) carrier system(#1,2): 1,400(w) x 1,600(l) x 600(h)mm 
   line speed:   transer-0.2~0.6m/sec     lifting-0.2~0.5m/sec
12) heating system :   steam heater
13) degreaser oil and water separator 
  tank(sus304): 600(w)x 1,200(l) x 700(h)mm
14) liquid agitator   
 15) acid bath filter:  4,800~6,000?/hr
16) piping system
17) basket    size: 500(w) x 600(l) x  400(h)mm
18) condensing water recovery ststem
19) electrical system 
   main power: 440v x 3Ø x 60hz  
  control power: 220v x 1Ø   x 60hz   
20) anti-polution system
21) carrier type tank :: 1,100?

sand blast m/c
make:sanga(korea)
year:2014
 conveyor type 
cycle time: 10~12sec
 cyclone & storage tank: Ø450 x 800(l)mm 
nozzle unit 
conveyor & turning unit 
loading/unloading unit 
nozzle oscillator 
dust collector

anti-air pollution equipment 
make:seonghwa(korea)
year:2014
packed-tower 
cap: 230cmm 
body: ?2,000 x 5,000(l)mm 
stack: ?650 x 3,000(l)mm 
turbo fan: 230?/min x 200mmaq 
motor: 20hp 

coating and dryer 
make:wastec(korean)
year:2002
14,500(l) x 4,000(w x 1,500(h) 
2) 300kw  
cap: 1,080ea/hr 
1) preheater dryer: 3,000(l) x 2,200(w)  , 30kw(1set)  
 blower: 23.3? x 19mmaq          
2) 1st coating  1,500(l) x 2,000(w)
nozzle: 6set 
 3) 1st dryer: 4,800(l) x 2,200(w), 24kw(2set)  
 blower: 20? x 17mmaq(2set)
4) 2nd coating  
 nozzle: 6set , 1,500(l) x 2,000(w)
5) 2nd dryer:: 4,000(l) x 2,000(w), 30kw(1set)  
 blower: 20? x 17mmaq(1set)
6) low temperature dryer:: 12,500(l) x 1,000(w), 30kw(3set)  
 blower: 23.3? x 190mmaq (3set)
7) cooling  : 1,000(l) x 800(w) , 10kw(1set)

washing equipment 
make:wastec(korean)
year:2002
7,000(l) x 1,100(w) x 1,800(h) 
2) cap: 1,500ea/hr 
3) 100kw
4)  r/o system
5) electric heater type

 dryer 
make:hanil(korea)
year:2002
 size: 1,440(l) x 2,000(w) x 1,530(h)
2) cap: 1,000ea/hr 
3)  40kw
4) car and rack 2set
5) heater: scr unit type

washer & bush insert m/c 
make:kumduk(korea)
year:2015
turn table unit: 2head 
unloading loader 
base & frame & cover: 75 x 75mm square pipe 
in loader unit 
index table unit 
washer loader unit x 2set
 washer check unit 
bush feed press unit: bush 

3-pin press  
make:kumduk(korea)
year:2015
base & frame & cover 
6-axics multi articulation  robot(yaskawa) 
manipulator
 index table unit 
3-pin feed unit
3-pin press unit 
unloading unit
 3-pin height check unit 

air compressor
make:taesan(korea)
year:2015
 
shaft powder coating line
make:misung(korea)
year:2015
 loading & unloading unit 
 preheater dry oven 45kw(15kw x 3set)
preheater after cooling zone: 
4) powder automatic equipment
5) idle transfer & index unit
6) loading transfer & masking    jig unit
7) oven jig: 16 x 130ea
8) powder recovery system
9) main baking oven 
10) floor conveyor
11) main cooling zone 

   bmj korea co.,ltd
director:jongduk
e-mail:paekjs1961@gmail.com
mobile)+82-10-7499-2567
  POWDER COATING EQUIPMENT PARKERIZING PHOSPHATE COATING EQUIPMENT MAKE:WASTEC(KOREAN) YEAR:2014 2) PROCESS TANK ? LOAD/UNLOAD(#1):SIZE: 800(W) X 1,200(L) X 1,200(H)MM ? ALKALI CLEANER TANK(#2) : SIZE: 800(W) X 1,200(L) X 1,200(H)MM 3) 2-STEP WATER RINSE BATH(#3,4): SIZE: 1,400(W) X 1,200(L) X 1,200(H)MM 4) ACID RINSE BATH(#5): SIZE: 750(W) X 1,200(L) X 1,200(H)MM 5) 2-STEP WATER RINSE BATH(#6,7): 1,400(W) X 1,200(L) X 1,200(H)MM 7) SURFACE CONDITION BATH(#8) :: 750(W) X 1,200(L) 1,200(H)MM 8) COATING BATH(#9,10) : 900(W) X 1,200(L) X 1,200(H)MM 9) HOT WATER RINSE(#11) : 750(W) X 1,200(L) X 1,200(H)MM 10) DRY TANK(#12) : SIZE(INSIDE): 700(W) X 1,200(L) X 1,200(H)MM SIZE(OUTSIDE): 1,300(W) X 2,000(L) X 1,200(H)MM TEMP: 90?~110? 11) CARRIER SYSTEM(#1,2): 1,400(W) X 1,600(L) X 600(H)MM LINE SPEED: TRANSER-0.2~0.6M/SEC LIFTING-0.2~0.5M/SEC 12) HEATING SYSTEM : STEAM HEATER 13) DEGREASER OIL AND WATER SEPARATOR TANK(SUS304): 600(W)X 1,200(L) X 700(H)MM 14) LIQUID AGITATOR 15) ACID BATH FILTER: 4,800~6,000?/HR 16) PIPING SYSTEM 17) BASKET SIZE: 500(W) X 600(L) X 400(H)MM 18) CONDENSING WATER RECOVERY STSTEM 19) ELECTRICAL SYSTEM MAIN POWER: 440V X 3Ø X 60HZ CONTROL POWER: 220V X 1Ø X 60HZ 20) ANTI-POLUTION SYSTEM 21) CARRIER TYPE TANK :: 1,100? SAND BLAST M/C MAKE:SANGA(KOREA) YEAR:2014 CONVEYOR TYPE CYCLE TIME: 10~12SEC CYCLONE & STORAGE TANK: Ø450 X 800(L)MM NOZZLE UNIT CONVEYOR & TURNING UNIT LOADING/UNLOADING UNIT NOZZLE OSCILLATOR DUST COLLECTOR ANTI-AIR POLLUTION EQUIPMENT MAKE:SEONGHWA(KOREA) YEAR:2014 PACKED-TOWER CAP: 230CMM BODY: ?2,000 X 5,000(L)MM STACK: ?650 X 3,000(L)MM TURBO FAN: 230?/MIN X 200MMAQ MOTOR: 20HP COATING AND DRYER MAKE:WASTEC(KOREAN) YEAR:2002 14,500(L) X 4,000(W X 1,500(H) 2) 300KW CAP: 1,080EA/HR 1) PREHEATER DRYER: 3,000(L) X 2,200(W) , 30KW(1SET) BLOWER: 23.3? X 19MMAQ 2) 1ST COATING 1,500(L) X 2,000(W) NOZZLE: 6SET 3) 1ST DRYER: 4,800(L) X 2,200(W), 24KW(2SET) BLOWER: 20? X 17MMAQ(2SET) 4) 2ND COATING NOZZLE: 6SET , 1,500(L) X 2,000(W) 5) 2ND DRYER:: 4,000(L) X 2,000(W), 30KW(1SET) BLOWER: 20? X 17MMAQ(1SET) 6) LOW TEMPERATURE DRYER:: 12,500(L) X 1,000(W), 30KW(3SET) BLOWER: 23.3? X 190MMAQ (3SET) 7) COOLING : 1,000(L) X 800(W) , 10KW(1SET) WASHING EQUIPMENT MAKE:WASTEC(KOREAN) YEAR:2002 7,000(L) X 1,100(W) X 1,800(H) 2) CAP: 1,500EA/HR 3) 100KW 4) R/O SYSTEM 5) ELECTRIC HEATER TYPE DRYER MAKE:HANIL(KOREA) YEAR:2002 SIZE: 1,440(L) X 2,000(W) X 1,530(H) 2) CAP: 1,000EA/HR 3) 40KW 4) CAR AND RACK 2SET 5) HEATER: SCR UNIT TYPE WASHER & BUSH INSERT M/C MAKE:KUMDUK(KOREA) YEAR:2015 TURN TABLE UNIT: 2HEAD UNLOADING LOADER BASE & FRAME & COVER: 75 X 75MM SQUARE PIPE IN LOADER UNIT INDEX TABLE UNIT WASHER LOADER UNIT X 2SET WASHER CHECK UNIT BUSH FEED PRESS UNIT: BUSH 3-PIN PRESS MAKE:KUMDUK(KOREA) YEAR:2015 BASE & FRAME & COVER 6-AXICS MULTI ARTICULATION ROBOT(YASKAWA) MANIPULATOR INDEX TABLE UNIT 3-PIN FEED UNIT 3-PIN PRESS UNIT UNLOADING UNIT 3-PIN HEIGHT CHECK UNIT AIR COMPRESSOR MAKE:TAESAN(KOREA) YEAR:2015 SHAFT POWDER COATING LINE MAKE:MISUNG(KOREA) YEAR:2015 LOADING & UNLOADING UNIT PREHEATER DRY OVEN 45KW(15KW X 3SET) PREHEATER AFTER COOLING ZONE: 4) POWDER AUTOMATIC EQUIPMENT 5) IDLE TRANSFER & INDEX UNIT 6) LOADING TRANSFER & MASKING JIG UNIT 7) OVEN JIG: 16 X 130EA 8) POWDER RECOVERY SYSTEM 9) MAIN BAKING OVEN 10) FLOOR CONVEYOR 11) MAIN COOLING ZONE BMJ KOREA CO.,LTD DIRECTOR:JONGDUK E-MAIL:PAEKJS1961@GMAIL.COM MOBILE)+82-10-7499-2567
Vendedor: BMJ KOREA
Año de construcción: usado
Ubicación: Land-4 decks, 600 x 1600 mm, oven  incl. steaming unit\r\ndimensions: l 2800 mm, w 1240 mm, h 2200 mm\r\n\r\n 4 DECKS, 600 X 1600 MM, OVEN INCL. STEAMING UNIT\R\NDIMENSIONS: L 2800 MM, W 1240 MM, H 2200 MM\R\N\R\N
Vendedor: Thünnesen GmbH
Año de construcción: usado
Ubicación: Land-power on time: 15665 h	
control system: fanuc 0i-md	
table: 1320 x 560 mm	
number of axes: 3	
travel distances:	
x: 1200 mm	
y: 600 mm	
z: 650 mm	
speed range: 8000 rpm	
spindle taper: iso 40	
rapid traverse:	
(x / y / z axes) 30 m/min	
distance from spindle nose to table:	
110 to 750 mm	
max. table load: 1400 kg	
tool changer positions: 32	
max. tool diameter: 80 mm	
max. tool length: 300 mm	
max. tool weight: 18 kg	
machine dimensions:	
3300 x 2615 x 2915 mm	
machine weight: 8200 kg	
accessories:	
cooling centre	
availability: 01.02.2019 POWER ON TIME: 15665 H CONTROL SYSTEM: FANUC 0I-MD TABLE: 1320 X 560 MM NUMBER OF AXES: 3 TRAVEL DISTANCES: X: 1200 MM Y: 600 MM Z: 650 MM SPEED RANGE: 8000 RPM SPINDLE TAPER: ISO 40 RAPID TRAVERSE: (X / Y / Z AXES) 30 M/MIN DISTANCE FROM SPINDLE NOSE TO TABLE: 110 TO 750 MM MAX. TABLE LOAD: 1400 KG TOOL CHANGER POSITIONS: 32 MAX. TOOL DIAMETER: 80 MM MAX. TOOL LENGTH: 300 MM MAX. TOOL WEIGHT: 18 KG MACHINE DIMENSIONS: 3300 X 2615 X 2915 MM MACHINE WEIGHT: 8200 KG ACCESSORIES: COOLING CENTRE AVAILABILITY: 01.02.2019
Vendedor: AMARON s.r.o.
Año de construcción: usado
Ubicación: Land-5 decks, 600 x 1600 mm, oven  incl. steaming unit\r\ndimensions: l 2800 mm, w 1240 mm, h 2310 mm\r\n 5 DECKS, 600 X 1600 MM, OVEN INCL. STEAMING UNIT\R\NDIMENSIONS: L 2800 MM, W 1240 MM, H 2310 MM\R\N
Vendedor: Thünnesen GmbH
Año de construcción: usado
Ubicación: Land-empering(hardening) furnaces of automobile parts.

 

1.   pit type tempering furnace x2sets

make:simdo(korea)

year:2016

capacity:3ton/charge

heater:kanthal strip heater

temperature:950degree

size:760mm diameter x1600mm

80kw/2part

control panel

 

2.      pit type furnace

make:simdo(korea)

year:2016

capacity:5ton/charge

heater:kanthal strip heater

temperature:950degree

size:1200mm diameter x1800mm

140kw/2part

control panel

 

 

3.      pit type furnace x2sets

make:woosung(korea)

year:2015

capacity:8ton/charge

heater:electric heater

temperature:930degree

size:1300mm diameter x2500mm

control panel

4.      pit type furnace x2sets

make:woosung(korea)

year:2010

capacity:8ton/charge

heater:electric heater

temperature:200-600degree

size:1500mm diameter x2700mm

control panel

 

5.   pit type furnace x2sets

make:simdo(korea)

year:2016

capacity:5ton/charge

380v, 140kw 3part

heating part:3part

heater:kanthal strip heater

temperature:950degree

pot size: inside diameter 1400mm x2000mm

        outside diameter 2400mm x3000mm

temperature:950degree

control panel

control:scr

gas:n2

 

6.   pit type furnace

make:simdo(korea)

year:2016

capacity:10ton/charge

380v, 150kw 3part

heating part:3part

heater:kanthal strip heater

temperature:950degree

pot size: inside diameter 1800mm x2400mm

        outside diameter 2800mm x3200mm

temperature:950degree

control panel

control:scr

gas:n2

bmj korea co.,ltd
director:jongduk
e-mail:paekjs1961@gmail.com
mobile)+82-10-7499-2567

bmj korea co.,ltd
director:jongduk
e-mail:paekjs1961@gmail.com
mobile)+82-10-7499-2567




 EMPERING(HARDENING) FURNACES OF AUTOMOBILE PARTS. 1. PIT TYPE TEMPERING FURNACE X2SETS MAKE:SIMDO(KOREA) YEAR:2016 CAPACITY:3TON/CHARGE HEATER:KANTHAL STRIP HEATER TEMPERATURE:950DEGREE SIZE:760MM DIAMETER X1600MM 80KW/2PART CONTROL PANEL 2. PIT TYPE FURNACE MAKE:SIMDO(KOREA) YEAR:2016 CAPACITY:5TON/CHARGE HEATER:KANTHAL STRIP HEATER TEMPERATURE:950DEGREE SIZE:1200MM DIAMETER X1800MM 140KW/2PART CONTROL PANEL 3. PIT TYPE FURNACE X2SETS MAKE:WOOSUNG(KOREA) YEAR:2015 CAPACITY:8TON/CHARGE HEATER:ELECTRIC HEATER TEMPERATURE:930DEGREE SIZE:1300MM DIAMETER X2500MM CONTROL PANEL 4. PIT TYPE FURNACE X2SETS MAKE:WOOSUNG(KOREA) YEAR:2010 CAPACITY:8TON/CHARGE HEATER:ELECTRIC HEATER TEMPERATURE:200-600DEGREE SIZE:1500MM DIAMETER X2700MM CONTROL PANEL 5. PIT TYPE FURNACE X2SETS MAKE:SIMDO(KOREA) YEAR:2016 CAPACITY:5TON/CHARGE 380V, 140KW 3PART HEATING PART:3PART HEATER:KANTHAL STRIP HEATER TEMPERATURE:950DEGREE POT SIZE: INSIDE DIAMETER 1400MM X2000MM OUTSIDE DIAMETER 2400MM X3000MM TEMPERATURE:950DEGREE CONTROL PANEL CONTROL:SCR GAS:N2 6. PIT TYPE FURNACE MAKE:SIMDO(KOREA) YEAR:2016 CAPACITY:10TON/CHARGE 380V, 150KW 3PART HEATING PART:3PART HEATER:KANTHAL STRIP HEATER TEMPERATURE:950DEGREE POT SIZE: INSIDE DIAMETER 1800MM X2400MM OUTSIDE DIAMETER 2800MM X3200MM TEMPERATURE:950DEGREE CONTROL PANEL CONTROL:SCR GAS:N2 BMJ KOREA CO.,LTD DIRECTOR:JONGDUK E-MAIL:PAEKJS1961@GMAIL.COM MOBILE)+82-10-7499-2567 BMJ KOREA CO.,LTD DIRECTOR:JONGDUK E-MAIL:PAEKJS1961@GMAIL.COM MOBILE)+82-10-7499-2567
Vendedor: BMJ KOREA
Año de construcción: usado
Ubicación: Land-products: oil, fat, water, glycol, max. working pressure: 82bar, product temperature: -20°c to 170°c.  PRODUCTS: OIL, FAT, WATER, GLYCOL, MAX. WORKING PRESSURE: 82BAR, PRODUCT TEMPERATURE: -20°C TO 170°C.
Vendedor: Innovac GmbH
Año de construcción: usado
Precio: 159.000 €
Ubicación: Land-multifoiler press\r\nbrand: bürkle \r\ntype: btf 1528-1400 flowline\r\nyear: 2007\r\n\r\nwith paternoster\r\n\r\nhigh-performance system for the membrane-free thermoforming of smooth and shaped mdf parts with thermoplastic foils.\r\n\r\ntechnical data:\r\n\r\n1. surface material:\r\nfrom the roll, or as a blank cut \r\na) pvc foil 0.30 - 1.0 mm\r\nb) high gloss foil 0,50 - 1,0 mm\r\nc) pet foil 0.35 - 0.6 mm\r\nall foils suitable for the bürkle thermoform process.\r\n\r\n2. carrier material:\r\nmdf board, with smooth profiled surfaces.\r\nthickness tolerance +/- 0.15 mm\r\n\r\n3. adhesives:\r\ndispersion adhesive 80 - 150 g / m²\r\nfor foils, 1-component or 2-component polyurethane adhesive.\r\n\r\ntechnology\r\n\r\nthermoform coating, without membrane, 1400 mm foil\r\neffective area 1330 x 2630 mm\r\nmax. work piece size 1250 x 2550 mm\r\nmin. foil width 1400 mm\r\nsealing dimensions 1370 m (u.u 1360 mm)\r\nwork piece thickness 16 - 38 mm\r\n\r\nworkflow on the entire flowline:\r\n1. positioning of the work piece on the same tray.\r\n2. detecting the work peice positions using a digital camera.\r\n3. cover with foil from the foil paternoster.\r\n4. load the laying pallet into the multifoiler.\r\n5. placing the sheet in the multipin system within the press while entering the press.\r\n6. process of coating without membrane in the process chamber of the multifoilers.\r\npreheat the foil, vacuum and shape with shaping pressure to max. 6 bar.\r\n7. discharge the entire batch into the rotary turner / multiturning.\r\n8. turn the laying pallet with the work piece around the longitudinal axis.\r\n9. discharge of the work pieces on a conveyor belt and transport from the turner.\r\n10. direct, manual cutting with finished cut (trimming) on the conveyor belt.\r\nalternative:\r\n20 cycles per hour, with commercially available foils.\r\nglossy foils have a longer cycle time due to longer warm-up times.\r\n\r\nimplementation of plants\r\n\r\npos. 10 1 receiving and loading station\r\n\r\npos. 20 1 bürkle - multifolier model btf 1528\r\ntechnical data:\r\nhotplate size: 1500 x 2800 mm\r\nloading side: 1500 mm\r\nmax. heating temperature 140 ° c\r\noperating side: right\r\n\r\nlifting, lowering and locking the press table with hydraulic.\r\n\r\n1 upper sealing frame, 15 mm\r\nattached to upper heating plate with quick clamping system.\r\n\r\n1 vacuum device\r\nwith vacuum pump and reservoir.\r\n\r\npos. 21 1 chain conveyor\r\ndriven, reversible, frequency controlled, in the press.\r\n\r\npos. 22 1 chain conveyor\r\ndriven, frequency controlled, under the press\r\n\r\npos. 23 3 lay pallets\r\n\r\npos. 25 1 bürkle multi-pin system\r\nfully automatic sub-system for the membraneless coating of milled mdf parts.\r\n\r\nfunction:\r\n1. the workpieces are placed as before in the laying pallet with the usual distances, but without sub-parts.\r\n2. an lcd matrix camera captures the image and stores it digitally with a very fine resolution of approx. 2 x 2 mm.\r\n3. a special software calculates the respective pins matching the image and initiates the setting of the pins in the btf.\r\n4. the round pins are located in a maintenance-friendly, solid metal block inside the multifoilers.\r\n5. the new laying pattern is set immediately after leaving the laying pallet, or during the new loading of the btf time-saving.\r\n6. the occupied pallet inverts over the finished set sheet and the coating process can begin as known.\r\n\r\npos. 30 1 bürkle multi-turning\r\nautomatic turning station for foil-coated work piece batches with integrated lifting device.\r\nfunction:\r\nthe full laying pallet travels from the btf to the rotary turner after coating. a conveyor belt lowers and clamps the entire batch with the pallet. the entire installation revolves around 180 degrees.\r\n\r\npos. 31 1 piece belt transport\r\n\r\npos. 61 1 foil discharger / discharging\r\nfor unloading the foils during static charges.\r\nto avoid foil contamination\r\nsuitable for 1 foil unwinding station\r\n\r\npos. 10 a paternoster\r\nfor 23 rolls (Ø 400 mm)\r\nproduct width: 1600 mm\r\nconstruction height: 5400 mm\r\noverall width: 2370 mm\r\nincl. 1 piece roll transport\r\n\r\nnote:\r\nthe specifications and descriptions are a copy of the order confirmation at that time. datas are for information and are not binding. MULTIFOILER PRESS\R\NBRAND: BüRKLE \R\NTYPE: BTF 1528-1400 FLOWLINE\R\NYEAR: 2007\R\N\R\NWITH PATERNOSTER\R\N\R\NHIGH-PERFORMANCE SYSTEM FOR THE MEMBRANE-FREE THERMOFORMING OF SMOOTH AND SHAPED MDF PARTS WITH THERMOPLASTIC FOILS.\R\N\R\NTECHNICAL DATA:\R\N\R\N1. SURFACE MATERIAL:\R\NFROM THE ROLL, OR AS A BLANK CUT \R\NA) PVC FOIL 0.30 - 1.0 MM\R\NB) HIGH GLOSS FOIL 0,50 - 1,0 MM\R\NC) PET FOIL 0.35 - 0.6 MM\R\NALL FOILS SUITABLE FOR THE BüRKLE THERMOFORM PROCESS.\R\N\R\N2. CARRIER MATERIAL:\R\NMDF BOARD, WITH SMOOTH PROFILED SURFACES.\R\NTHICKNESS TOLERANCE +/- 0.15 MM\R\N\R\N3. ADHESIVES:\R\NDISPERSION ADHESIVE 80 - 150 G / M²\R\NFOR FOILS, 1-COMPONENT OR 2-COMPONENT POLYURETHANE ADHESIVE.\R\N\R\NTECHNOLOGY\R\N\R\NTHERMOFORM COATING, WITHOUT MEMBRANE, 1400 MM FOIL\R\NEFFECTIVE AREA 1330 X 2630 MM\R\NMAX. WORK PIECE SIZE 1250 X 2550 MM\R\NMIN. FOIL WIDTH 1400 MM\R\NSEALING DIMENSIONS 1370 M (U.U 1360 MM)\R\NWORK PIECE THICKNESS 16 - 38 MM\R\N\R\NWORKFLOW ON THE ENTIRE FLOWLINE:\R\N1. POSITIONING OF THE WORK PIECE ON THE SAME TRAY.\R\N2. DETECTING THE WORK PEICE POSITIONS USING A DIGITAL CAMERA.\R\N3. COVER WITH FOIL FROM THE FOIL PATERNOSTER.\R\N4. LOAD THE LAYING PALLET INTO THE MULTIFOILER.\R\N5. PLACING THE SHEET IN THE MULTIPIN SYSTEM WITHIN THE PRESS WHILE ENTERING THE PRESS.\R\N6. PROCESS OF COATING WITHOUT MEMBRANE IN THE PROCESS CHAMBER OF THE MULTIFOILERS.\R\NPREHEAT THE FOIL, VACUUM AND SHAPE WITH SHAPING PRESSURE TO MAX. 6 BAR.\R\N7. DISCHARGE THE ENTIRE BATCH INTO THE ROTARY TURNER / MULTITURNING.\R\N8. TURN THE LAYING PALLET WITH THE WORK PIECE AROUND THE LONGITUDINAL AXIS.\R\N9. DISCHARGE OF THE WORK PIECES ON A CONVEYOR BELT AND TRANSPORT FROM THE TURNER.\R\N10. DIRECT, MANUAL CUTTING WITH FINISHED CUT (TRIMMING) ON THE CONVEYOR BELT.\R\NALTERNATIVE:\R\N20 CYCLES PER HOUR, WITH COMMERCIALLY AVAILABLE FOILS.\R\NGLOSSY FOILS HAVE A LONGER CYCLE TIME DUE TO LONGER WARM-UP TIMES.\R\N\R\NIMPLEMENTATION OF PLANTS\R\N\R\NPOS. 10 1 RECEIVING AND LOADING STATION\R\N\R\NPOS. 20 1 BüRKLE - MULTIFOLIER MODEL BTF 1528\R\NTECHNICAL DATA:\R\NHOTPLATE SIZE: 1500 X 2800 MM\R\NLOADING SIDE: 1500 MM\R\NMAX. HEATING TEMPERATURE 140 ° C\R\NOPERATING SIDE: RIGHT\R\N\R\NLIFTING, LOWERING AND LOCKING THE PRESS TABLE WITH HYDRAULIC.\R\N\R\N1 UPPER SEALING FRAME, 15 MM\R\NATTACHED TO UPPER HEATING PLATE WITH QUICK CLAMPING SYSTEM.\R\N\R\N1 VACUUM DEVICE\R\NWITH VACUUM PUMP AND RESERVOIR.\R\N\R\NPOS. 21 1 CHAIN CONVEYOR\R\NDRIVEN, REVERSIBLE, FREQUENCY CONTROLLED, IN THE PRESS.\R\N\R\NPOS. 22 1 CHAIN CONVEYOR\R\NDRIVEN, FREQUENCY CONTROLLED, UNDER THE PRESS\R\N\R\NPOS. 23 3 LAY PALLETS\R\N\R\NPOS. 25 1 BüRKLE MULTI-PIN SYSTEM\R\NFULLY AUTOMATIC SUB-SYSTEM FOR THE MEMBRANELESS COATING OF MILLED MDF PARTS.\R\N\R\NFUNCTION:\R\N1. THE WORKPIECES ARE PLACED AS BEFORE IN THE LAYING PALLET WITH THE USUAL DISTANCES, BUT WITHOUT SUB-PARTS.\R\N2. AN LCD MATRIX CAMERA CAPTURES THE IMAGE AND STORES IT DIGITALLY WITH A VERY FINE RESOLUTION OF APPROX. 2 X 2 MM.\R\N3. A SPECIAL SOFTWARE CALCULATES THE RESPECTIVE PINS MATCHING THE IMAGE AND INITIATES THE SETTING OF THE PINS IN THE BTF.\R\N4. THE ROUND PINS ARE LOCATED IN A MAINTENANCE-FRIENDLY, SOLID METAL BLOCK INSIDE THE MULTIFOILERS.\R\N5. THE NEW LAYING PATTERN IS SET IMMEDIATELY AFTER LEAVING THE LAYING PALLET, OR DURING THE NEW LOADING OF THE BTF TIME-SAVING.\R\N6. THE OCCUPIED PALLET INVERTS OVER THE FINISHED SET SHEET AND THE COATING PROCESS CAN BEGIN AS KNOWN.\R\N\R\NPOS. 30 1 BüRKLE MULTI-TURNING\R\NAUTOMATIC TURNING STATION FOR FOIL-COATED WORK PIECE BATCHES WITH INTEGRATED LIFTING DEVICE.\R\NFUNCTION:\R\NTHE FULL LAYING PALLET TRAVELS FROM THE BTF TO THE ROTARY TURNER AFTER COATING. A CONVEYOR BELT LOWERS AND CLAMPS THE ENTIRE BATCH WITH THE PALLET. THE ENTIRE INSTALLATION REVOLVES AROUND 180 DEGREES.\R\N\R\NPOS. 31 1 PIECE BELT TRANSPORT\R\N\R\NPOS. 61 1 FOIL DISCHARGER / DISCHARGING\R\NFOR UNLOADING THE FOILS DURING STATIC CHARGES.\R\NTO AVOID FOIL CONTAMINATION\R\NSUITABLE FOR 1 FOIL UNWINDING STATION\R\N\R\NPOS. 10 A PATERNOSTER\R\NFOR 23 ROLLS (Ø 400 MM)\R\NPRODUCT WIDTH: 1600 MM\R\NCONSTRUCTION HEIGHT: 5400 MM\R\NOVERALL WIDTH: 2370 MM\R\NINCL. 1 PIECE ROLL TRANSPORT\R\N\R\NNOTE:\R\NTHE SPECIFICATIONS AND DESCRIPTIONS ARE A COPY OF THE ORDER CONFIRMATION AT THAT TIME. DATAS ARE FOR INFORMATION AND ARE NOT BINDING.
Vendedor: Wehrmann Holzbearbeitungsmaschinen GmbH & Co.KG
Año de construcción: usado
Ubicación: Land-standalone/ inline operation component space: 525x400/ 350x300mm, max. centering surface: 33x33mm, compressed air supply: 6bar, length: 1760mm, width: 1430mm, height: 1120, weight: 400kg, year of construction: ca. 1998, including feeder set-up station, calibration plate and 5x placement tools.  STANDALONE/ INLINE OPERATION COMPONENT SPACE: 525X400/ 350X300MM, MAX. CENTERING SURFACE: 33X33MM, COMPRESSED AIR SUPPLY: 6BAR, LENGTH: 1760MM, WIDTH: 1430MM, HEIGHT: 1120, WEIGHT: 400KG, YEAR OF CONSTRUCTION: CA. 1998, INCLUDING FEEDER SET-UP STATION, CALIBRATION PLATE AND 5X PLACEMENT TOOLS.
Vendedor: Innovac GmbH
Año de construcción: usado
Ubicación: Land-turning diameter: 700 mm<br/>turning length: 2000 mm<br/>control: gildemeister epm2<br/>swing diameter over slide rest: 410 mm<br/>z-axis: 630 mm<br/>x-axis: 500 mm<br/>spindle head: 11 <br/>spindle diameter in front bearing: 130 mm<br/>spindle bore: 73 mm<br/>spindle motor: 50 kw<br/>spindle turning speed range: 11- 1400 u/min<br/>max. torque on the spindle: 3700 nm<br/>tooling places: 13 <br/>chain magazin:  <br/>total power requirement: 78 kw<br/>weight of the machine ca.: 10 t<br/>dimensions of the machine ca.: 6,5 x 3,5 x 2,8 m<br/><br/>- power chuck smw kncs 630 +500<br/>- 12-fold drum type tool magazine<br/>- chip conveyor and coolant device<br/>- various tolholders<br/><br/><br/><br/><br/><br/> TURNING DIAMETER: 700 MM
TURNING LENGTH: 2000 MM
CONTROL: GILDEMEISTER EPM2
SWING DIAMETER OVER SLIDE REST: 410 MM
Z-AXIS: 630 MM
X-AXIS: 500 MM
SPINDLE HEAD: 11
SPINDLE DIAMETER IN FRONT BEARING: 130 MM
SPINDLE BORE: 73 MM
SPINDLE MOTOR: 50 KW
SPINDLE TURNING SPEED RANGE: 11- 1400 U/MIN
MAX. TORQUE ON THE SPINDLE: 3700 NM
TOOLING PLACES: 13
CHAIN MAGAZIN:
TOTAL POWER REQUIREMENT: 78 KW
WEIGHT OF THE MACHINE CA.: 10 T
DIMENSIONS OF THE MACHINE CA.: 6,5 X 3,5 X 2,8 M

- POWER CHUCK SMW KNCS 630 +500
- 12-FOLD DRUM TYPE TOOL MAGAZINE
- CHIP CONVEYOR AND COOLANT DEVICE
- VARIOUS TOLHOLDERS





Vendedor: Gromag AG
Año de construcción: usado
Precio: 39.900 €
Ubicación: Land-elba esm 105

concrete mixing plant of elba
manufacturer: elba
type: 105 va-cia
year of construction: 1990
performance: 80 m â³/h
mixer: elba shaft mixer 2 mâ³
series pocket silo: 88 t / bag
weighing band: fa. bleichert - 5000 kg
silos: 4 (2 x 80t + 1 x 50t + 1x40t)
binder scale: 1000 kg level: 500 kg additional medium scale: wã¼rschum 20 kg (kfw 5/12.5)

control: polka discover ibs 33w + komdis year 2007
optional:
heating: weho-ndk 35 407 kw.h - fuel oil
recycling plant: joachim - 1998
optional heating/recycling system, these will be charged separately.
omissions and prior sale reserved, are sold from the site. ELBA ESM 105 CONCRETE MIXING PLANT OF ELBA MANUFACTURER: ELBA TYPE: 105 VA-CIA YEAR OF CONSTRUCTION: 1990 PERFORMANCE: 80 M &ACIRC;&SUP3;/H MIXER: ELBA SHAFT MIXER 2 M&ACIRC;&SUP3; SERIES POCKET SILO: 88 T / BAG WEIGHING BAND: FA. BLEICHERT - 5000 KG SILOS: 4 (2 X 80T + 1 X 50T + 1X40T) BINDER SCALE: 1000 KG LEVEL: 500 KG ADDITIONAL MEDIUM SCALE: W&ATILDE;&FRAC14;RSCHUM 20 KG (KFW 5/12.5) CONTROL: POLKA DISCOVER IBS 33W + KOMDIS YEAR 2007 OPTIONAL: HEATING: WEHO-NDK 35 407 KW.H - FUEL OIL RECYCLING PLANT: JOACHIM - 1998 OPTIONAL HEATING/RECYCLING SYSTEM, THESE WILL BE CHARGED SEPARATELY. OMISSIONS AND PRIOR SALE RESERVED, ARE SOLD FROM THE SITE.
Vendedor: GROMITEC
Año de construcción: usado
Ubicación: Land-turning diameter: 430 mm<br/>turning length: 1500 mm<br/>control: epl 10<br/>swing dia. over bed: 500 mm<br/>swing diameter over cross slide guide: 330 mm<br/>traverse x-axis 1: 245 mm<br/>traverse z-axis 1: 1026 mm<br/>traverse x-axis 2: 130 mm<br/>traverse z-axis 2: 665 mm<br/>spindle nose: a8 <br/>spindle bearing diameter: 120 mm<br/>spindle bore: 81 mm<br/>turning speed range - main spindle: 22 ~ 2800 u/min<br/>power capacity - main spindel: 50 kw<br/>rapid traverse: 10 m/min<br/>turret 1:  <br/>numbers of turret head positions: 12 <br/>number of driven tools: 6 pos<br/>spindle speed driven tools: 20 ~ 2.500 min -1<br/>power capacity - driven tools: 6 kw<br/>shank diameter: 25 x 25 mm<br/>steady: 10-90 mm<br/>chip conveyor:  kw<br/>coolantsystem:  <br/>tailstock:  <br/>3-jaw chuck: smw kncs 400+315<br/>div. tool holder:  <br/>div.drv.tools:  <br/>oil mist extraction:  <br/><br/><br/><br/><br/><br/> TURNING DIAMETER: 430 MM
TURNING LENGTH: 1500 MM
CONTROL: EPL 10
SWING DIA. OVER BED: 500 MM
SWING DIAMETER OVER CROSS SLIDE GUIDE: 330 MM
TRAVERSE X-AXIS 1: 245 MM
TRAVERSE Z-AXIS 1: 1026 MM
TRAVERSE X-AXIS 2: 130 MM
TRAVERSE Z-AXIS 2: 665 MM
SPINDLE NOSE: A8
SPINDLE BEARING DIAMETER: 120 MM
SPINDLE BORE: 81 MM
TURNING SPEED RANGE - MAIN SPINDLE: 22 ~ 2800 U/MIN
POWER CAPACITY - MAIN SPINDEL: 50 KW
RAPID TRAVERSE: 10 M/MIN
TURRET 1:
NUMBERS OF TURRET HEAD POSITIONS: 12
NUMBER OF DRIVEN TOOLS: 6 POS
SPINDLE SPEED DRIVEN TOOLS: 20 ~ 2.500 MIN -1
POWER CAPACITY - DRIVEN TOOLS: 6 KW
SHANK DIAMETER: 25 X 25 MM
STEADY: 10-90 MM
CHIP CONVEYOR: KW
COOLANTSYSTEM:
TAILSTOCK:
3-JAW CHUCK: SMW KNCS 400+315
DIV. TOOL HOLDER:
DIV.DRV.TOOLS:
OIL MIST EXTRACTION:





Vendedor: Gromag AG
Año de construcción: usado
Ubicación: Land-x: 5400 mm
y: 2600 mm
w: 1500 mm
b-axis: +/-105 °
c-axis: +/-200 °
table size: 5000 x 2000 mm
speed range: 1500-24000 rpm
spindle drive: 10 kw
spindle retainer: hsk 63 f
tool changer: 10-fold
control: fanuc 18i mb controller
becker vacuum pump: 250 m³/h

suitable for model construction, woodwork or aluminium machining, stop pin on the edge of the table - height 90 mm, blowing nozzle on the spindle head to blow out the milling chips, vacuum table, tabletop as new - was always covered with mdf panels, only less than half shifts run

total capacity: 28 kw
machine weight: 15000 kg
dimensions (w x d x h): 11 x 7 x 4.5 m

condition: very good 

accessories: 
16 holder
replacement spindle overhaul and not yet used
tribos automatic clamping system with various bushings
water cooler for the spindle  X: 5400 MM Y: 2600 MM W: 1500 MM B-AXIS: +/-105 ° C-AXIS: +/-200 ° TABLE SIZE: 5000 X 2000 MM SPEED RANGE: 1500-24000 RPM SPINDLE DRIVE: 10 KW SPINDLE RETAINER: HSK 63 F TOOL CHANGER: 10-FOLD CONTROL: FANUC 18I MB CONTROLLER BECKER VACUUM PUMP: 250 M³/H SUITABLE FOR MODEL CONSTRUCTION, WOODWORK OR ALUMINIUM MACHINING, STOP PIN ON THE EDGE OF THE TABLE - HEIGHT 90 MM, BLOWING NOZZLE ON THE SPINDLE HEAD TO BLOW OUT THE MILLING CHIPS, VACUUM TABLE, TABLETOP AS NEW - WAS ALWAYS COVERED WITH MDF PANELS, ONLY LESS THAN HALF SHIFTS RUN TOTAL CAPACITY: 28 KW MACHINE WEIGHT: 15000 KG DIMENSIONS (W X D X H): 11 X 7 X 4.5 M CONDITION: VERY GOOD ACCESSORIES: 16 HOLDER REPLACEMENT SPINDLE OVERHAUL AND NOT YET USED TRIBOS AUTOMATIC CLAMPING SYSTEM WITH VARIOUS BUSHINGS WATER COOLER FOR THE SPINDLE
Vendedor: Alfred Feldmann Werkzeugmaschinen
Año de construcción: usado
Ubicación: Land-please check the plaque for technical specifications.

if you need further information, please feel free to contact us via mail or phone. PLEASE CHECK THE PLAQUE FOR TECHNICAL SPECIFICATIONS. IF YOU NEED FURTHER INFORMATION, PLEASE FEEL FREE TO CONTACT US VIA MAIL OR PHONE.
Vendedor: Dimex Import Export
Año de construcción: usado
Ubicación: Land-there are two identical component placement systems available, x-travel: 500mm, y-travel: 500mm, z-travel: 40mm, length: 1220mm, width: 1220mm, height: 1500mm, weight: 850kg, including glue dosing, ce marking is missing and needs to be replaced.  THERE ARE TWO IDENTICAL COMPONENT PLACEMENT SYSTEMS AVAILABLE, X-TRAVEL: 500MM, Y-TRAVEL: 500MM, Z-TRAVEL: 40MM, LENGTH: 1220MM, WIDTH: 1220MM, HEIGHT: 1500MM, WEIGHT: 850KG, INCLUDING GLUE DOSING, CE MARKING IS MISSING AND NEEDS TO BE REPLACED.
Vendedor: Innovac GmbH
Año de construcción: usado
Precio: 2.150 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Ubicación: Land-ex running take out v 200, revision due EX RUNNING TAKE OUT V 200, REVISION DUE
Vendedor: Techno-Commerce GmbH
Año de construcción: usado
Precio: 150 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Precio: 99 €
Ubicación: Land-differential pressure transmitter, delta bar fmd230 ld3f1ec7cbk, endress & hauser
manufacturer: endress & hauser
type: delta bar fmd230 ld3f1ec7cbk
flange: dn80, pn40, material 316l

condition used
warranty of in accordance with common agreement DIFFERENTIAL PRESSURE TRANSMITTER, DELTA BAR FMD230 LD3F1EC7CBK, ENDRESS & HAUSER MANUFACTURER: ENDRESS & HAUSER TYPE: DELTA BAR FMD230 LD3F1EC7CBK FLANGE: DN80, PN40, MATERIAL 316L CONDITION USED WARRANTY OF IN ACCORDANCE WITH COMMON AGREEMENT
Vendedor: IPV GmbH
Año de construcción: usado
Precio: 240 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Precio: 11.530 €
Ubicación: Land-boge screw compressor s 125 air cooled

ready to use, automatically working with ce mark

constant belt tension, maintenance-free, patented boge-gm drive system
oil injection cooled boge compressor stage with optimised screw profile
-in each operating phase constant low residual oil content of the compressed air through effective preliminary separation in the horizontally mounted compressed air oil separator tank
-permanent compaction temperature and pressure display
-precise pressure adjustment via the keyboard
frost protection for compressors up to-10 ° c

control: ratio boge

maintenance incl. suction regulator, mdv conversion to 8 bar new

good condition BOGE SCREW COMPRESSOR S 125 AIR COOLED READY TO USE, AUTOMATICALLY WORKING WITH CE MARK CONSTANT BELT TENSION, MAINTENANCE-FREE, PATENTED BOGE-GM DRIVE SYSTEM OIL INJECTION COOLED BOGE COMPRESSOR STAGE WITH OPTIMISED SCREW PROFILE -IN EACH OPERATING PHASE CONSTANT LOW RESIDUAL OIL CONTENT OF THE COMPRESSED AIR THROUGH EFFECTIVE PRELIMINARY SEPARATION IN THE HORIZONTALLY MOUNTED COMPRESSED AIR OIL SEPARATOR TANK -PERMANENT COMPACTION TEMPERATURE AND PRESSURE DISPLAY -PRECISE PRESSURE ADJUSTMENT VIA THE KEYBOARD FROST PROTECTION FOR COMPRESSORS UP TO-10 ° C CONTROL: RATIO BOGE MAINTENANCE INCL. SUCTION REGULATOR, MDV CONVERSION TO 8 BAR NEW GOOD CONDITION
Vendedor: BOGE KOMPRESSOREN Otto Boge GmbH & Co.KG
Año de construcción: usado
Precio: 980 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Precio: 250 €
Ubicación: Land-digital differential pressure transmitter, deltabar s fmd76, endress & hauser
manufacturer: endress & hauser
type: deltabar s fmd76-1mj7f1mbaa

- with ceranic sensor
- overload-proof and function-monitored, communication via hart, profibus pa
- material: 1.4404
- flange dn80, pn40
- ex protected version

condition used, but almost new
functional warranty as agreed DIGITAL DIFFERENTIAL PRESSURE TRANSMITTER, DELTABAR S FMD76, ENDRESS & HAUSER MANUFACTURER: ENDRESS & HAUSER TYPE: DELTABAR S FMD76-1MJ7F1MBAA - WITH CERANIC SENSOR - OVERLOAD-PROOF AND FUNCTION-MONITORED, COMMUNICATION VIA HART, PROFIBUS PA - MATERIAL: 1.4404 - FLANGE DN80, PN40 - EX PROTECTED VERSION CONDITION USED, BUT ALMOST NEW FUNCTIONAL WARRANTY AS AGREED
Vendedor: IPV GmbH
Año de construcción: usado
Precio: 6 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Precio: 320 €
Ubicación: Land-used kettenstemmer
internal number: m2687

producer elu
type fmd 33
ma. number 33782

year unknown
power 2,2 kw
speed 2,700 rpm.
mounted chain 12 mm

additional chain 16 mm

item location: 58730 frã¶ndenberg/ruhr

the machine can be visited like to see power and tried out.

a forklift/crane for loading is available.

we reserve the right to a sale.

there is the way learned to examine suburb for sale articles. specific questions should be clarified in advance. the information, technical data, dimensions, year, condition are non-binding and were shown to the best of my knowledge and belief. errors are reserved. the warranty / guarantee is excluded. the goods will be sold from location / camp, with national transfer of risk to the buyer, this also applies to a shipping from us, which we have carried out on your behalf. this offer is only to traders, merchants and legal persons.

specified trade names, and trademarks are property of their owners and are used only for identification and description of products.!

the structure and the electrical connection of the machine / the device must be carried out by a qualified person trained or checked.

see also my other offers.

the article must be paid unless otherwise agreed within 14 days of invoice creation and picked up.
otherwise, the cost of the storage charge must be made. USED KETTENSTEMMER INTERNAL NUMBER: M2687 PRODUCER ELU TYPE FMD 33 MA. NUMBER 33782 YEAR UNKNOWN POWER 2,2 KW SPEED 2,700 RPM. MOUNTED CHAIN 12 MM ADDITIONAL CHAIN 16 MM ITEM LOCATION: 58730 FR&ATILDE;&PARA;NDENBERG/RUHR THE MACHINE CAN BE VISITED LIKE TO SEE POWER AND TRIED OUT. A FORKLIFT/CRANE FOR LOADING IS AVAILABLE. WE RESERVE THE RIGHT TO A SALE. THERE IS THE WAY LEARNED TO EXAMINE SUBURB FOR SALE ARTICLES. SPECIFIC QUESTIONS SHOULD BE CLARIFIED IN ADVANCE. THE INFORMATION, TECHNICAL DATA, DIMENSIONS, YEAR, CONDITION ARE NON-BINDING AND WERE SHOWN TO THE BEST OF MY KNOWLEDGE AND BELIEF. ERRORS ARE RESERVED. THE WARRANTY / GUARANTEE IS EXCLUDED. THE GOODS WILL BE SOLD FROM LOCATION / CAMP, WITH NATIONAL TRANSFER OF RISK TO THE BUYER, THIS ALSO APPLIES TO A SHIPPING FROM US, WHICH WE HAVE CARRIED OUT ON YOUR BEHALF. THIS OFFER IS ONLY TO TRADERS, MERCHANTS AND LEGAL PERSONS. SPECIFIED TRADE NAMES, AND TRADEMARKS ARE PROPERTY OF THEIR OWNERS AND ARE USED ONLY FOR IDENTIFICATION AND DESCRIPTION OF PRODUCTS.! THE STRUCTURE AND THE ELECTRICAL CONNECTION OF THE MACHINE / THE DEVICE MUST BE CARRIED OUT BY A QUALIFIED PERSON TRAINED OR CHECKED. SEE ALSO MY OTHER OFFERS. THE ARTICLE MUST BE PAID UNLESS OTHERWISE AGREED WITHIN 14 DAYS OF INVOICE CREATION AND PICKED UP. OTHERWISE, THE COST OF THE STORAGE CHARGE MUST BE MADE.
Vendedor: Fritz Ernst Maschinenhandel e K
Año de construcción: usado
Precio: 390 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Precio: used machinery auction RESALE 6.000 €
Ubicación: Land-engine performance 130 kw, operating pressure 9.6 bar, max rpm 22,000 rpm, diesel engine, elapsed. hours of operation 8.653 hours, tuv and tuv 02/2020 ENGINE PERFORMANCE 130 KW, OPERATING PRESSURE 9.6 BAR, MAX RPM 22,000 RPM, DIESEL ENGINE, ELAPSED. HOURS OF OPERATION 8.653 HOURS, TUV AND TUV 02/2020
Vendedor: Indutax GmbH
Año de construcción: usado
Precio: 30 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Precio: 1.490 €
Ubicación: Land-new brake motor / flange motor lenze mdfabs 180-12, 18.5 kw
manufacturer: lenze
type: mdfabs 180-12

condition: the brake motor was purchased from a stock of spare parts and is completely new.

technical data:
-type flange motor
-with brake and resolver
-18.5 kw, 400 v, 1500 rpm
-thermal protection kty sensor
-resolver type ts 265
-with fan type a2e 300
-motor shaft with shaft protection

dimensions:
flange outside diameter 350 mm, centering diameter 250 mm,.
reference diameter 300 mm, z = 4
total length 900mm, width 380mm, height 450mm
weight approx. 300kg

(the current price is â?¬ 5000. vat)
the selling price â?¬ 1490. vat  NEW BRAKE MOTOR / FLANGE MOTOR LENZE MDFABS 180-12, 18.5 KW MANUFACTURER: LENZE TYPE: MDFABS 180-12 CONDITION: THE BRAKE MOTOR WAS PURCHASED FROM A STOCK OF SPARE PARTS AND IS COMPLETELY NEW. TECHNICAL DATA: -TYPE FLANGE MOTOR -WITH BRAKE AND RESOLVER -18.5 KW, 400 V, 1500 RPM -THERMAL PROTECTION KTY SENSOR -RESOLVER TYPE TS 265 -WITH FAN TYPE A2E 300 -MOTOR SHAFT WITH SHAFT PROTECTION DIMENSIONS: FLANGE OUTSIDE DIAMETER 350 MM, CENTERING DIAMETER 250 MM,. REFERENCE DIAMETER 300 MM, Z = 4 TOTAL LENGTH 900MM, WIDTH 380MM, HEIGHT 450MM WEIGHT APPROX. 300KG (THE CURRENT PRICE IS â?¬ 5000. VAT) THE SELLING PRICE â?¬ 1490. VAT
Vendedor: IPV GmbH
Año de construcción: usado
Precio: 220 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Precio: 2.689 €
Ubicación: Land-with digital display.

technical data:

brand: matra

type: md 22 s

turning length 1000 mm

tip height: 220 mm

spindle speeds 20-2000 rpm WITH DIGITAL DISPLAY. TECHNICAL DATA: BRAND: MATRA TYPE: MD 22 S TURNING LENGTH 1000 MM TIP HEIGHT: 220 MM SPINDLE SPEEDS 20-2000 RPM
Vendedor: A-Z Maschinenwelt
Año de construcción: usado
Precio: 250 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Ubicación: Land-gebr. cnc milling machining center make mmd
	model premill v 760l-sn
                                                   year 2014 control siemens 828 d, shop mill, rsr 232 interface

procedures:
	x 760 mm
		y 400 mm
		z 400 mm
	distance spindle center and table top 102-502 mm
	table size 1270 x 305 mm
	maximum work-piece weight 200 kg
	spindle speeds up to 8000 rpm-1
	taper din 69871 40
	rapid traverse x-y-z 12 m / min
	feed speed 10 m / min
	positioning â±0. 008 mm
	number of tools 16 piece
	max tool:
	ã? 100 mm
		length 200 mm
		weight 6 kg
	spindle motor 7, 0kw
	feed motor x-y-z 2,3 kw
	power supply 12 kva
	external dimensions:
	2510 mm
		2170 mm deep
		2390 mm
	weight approx.		2500 kg
	with:
	4 axis cnc 250r with tailstock and 8 ' feed
		lm guide x-y-z axis
		prepared internal cooling
		electr. handwheel
		central lubrication system
		rigid tapping
		coolant system
		

 GEBR. CNC MILLING MACHINING CENTER MAKE MMD MODEL PREMILL V 760L-SN YEAR 2014 CONTROL SIEMENS 828 D, SHOP MILL, RSR 232 INTERFACE PROCEDURES: X 760 MM Y 400 MM Z 400 MM DISTANCE SPINDLE CENTER AND TABLE TOP 102-502 MM TABLE SIZE 1270 X 305 MM MAXIMUM WORK-PIECE WEIGHT 200 KG SPINDLE SPEEDS UP TO 8000 RPM-1 TAPER DIN 69871 40 RAPID TRAVERSE X-Y-Z 12 M / MIN FEED SPEED 10 M / MIN POSITIONING &ACIRC;&PLUSMN;0. 008 MM NUMBER OF TOOLS 16 PIECE MAX TOOL: &ATILDE;? 100 MM LENGTH 200 MM WEIGHT 6 KG SPINDLE MOTOR 7, 0KW FEED MOTOR X-Y-Z 2,3 KW POWER SUPPLY 12 KVA EXTERNAL DIMENSIONS: 2510 MM 2170 MM DEEP 2390 MM WEIGHT APPROX. 2500 KG WITH: 4 AXIS CNC 250R WITH TAILSTOCK AND 8 ' FEED LM GUIDE X-Y-Z AXIS PREPARED INTERNAL COOLING ELECTR. HANDWHEEL CENTRAL LUBRICATION SYSTEM RIGID TAPPING COOLANT SYSTEM
Vendedor: RUDOLF BANDMANN WERKZEUGMASCHINEN e.K.
Año de construcción: usado
Precio: 320 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Ubicación: Land-complete filling / bottling line for disposable pet bottles.
0.33 - 0.5 - 1.0-1.5 liter.

suitable for filling of mineral water and juices,
both sparkling (carbonated) and still.

scope of supply:

khs pet filler
drv-pet (vf) 45
- incl. filler enhancement hot filling -

alcoa capper
4109/360-2001
- agitator for sports cap -

filling level control 
unicept fhk rf

rinser khs
fr-zr 45

labeller khs/anker
roland 5 hs

carrier handle applicator twin pack
mdel

traypacker smi
lsk 45 t

shrink tunnel smi
st

sealing machine huettinger
tig 2.5/300

conveyor system vm logistics

label applicator weber
5100

bottle twister trans tech hysek

bottle press strautmann

nitrogen dosing unit
terboven   COMPLETE FILLING / BOTTLING LINE FOR DISPOSABLE PET BOTTLES. 0.33 - 0.5 - 1.0-1.5 LITER. SUITABLE FOR FILLING OF MINERAL WATER AND JUICES, BOTH SPARKLING (CARBONATED) AND STILL. SCOPE OF SUPPLY: KHS PET FILLER DRV-PET (VF) 45 - INCL. FILLER ENHANCEMENT HOT FILLING - ALCOA CAPPER 4109/360-2001 - AGITATOR FOR SPORTS CAP - FILLING LEVEL CONTROL UNICEPT FHK RF RINSER KHS FR-ZR 45 LABELLER KHS/ANKER ROLAND 5 HS CARRIER HANDLE APPLICATOR TWIN PACK MDEL TRAYPACKER SMI LSK 45 T SHRINK TUNNEL SMI ST SEALING MACHINE HUETTINGER TIG 2.5/300 CONVEYOR SYSTEM VM LOGISTICS LABEL APPLICATOR WEBER 5100 BOTTLE TWISTER TRANS TECH HYSEK BOTTLE PRESS STRAUTMANN NITROGEN DOSING UNIT TERBOVEN
Vendedor: Ohrter Getränkemaschinen Handel
Año de construcción: usado
Precio: 320 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Ubicación: Land-spiral mixer dough machine
kemper president
model: pres 125 ae v
with 2 retractable tank car
kneading machine for max 200 kg dough
stainless steel execution
touch control with temperature sensor
cover with switch ring
plumbed for wmd
with led timer and 2 courses
raising and lowering control
connection 400v, 50 amp, 63a-cee plug
mass approx.: 175 x 111 x 170 cm lxwxh second-hand machine cleaned and checked workshop
6 months warranty for the parts installed by us.
SPIRAL MIXER DOUGH MACHINE KEMPER PRESIDENT MODEL: PRES 125 AE V WITH 2 RETRACTABLE TANK CAR KNEADING MACHINE FOR MAX 200 KG DOUGH STAINLESS STEEL EXECUTION TOUCH CONTROL WITH TEMPERATURE SENSOR COVER WITH SWITCH RING PLUMBED FOR WMD WITH LED TIMER AND 2 COURSES RAISING AND LOWERING CONTROL CONNECTION 400V, 50 AMP, 63A-CEE PLUG MASS APPROX.: 175 X 111 X 170 CM LXWXH SECOND-HAND MACHINE CLEANED AND CHECKED WORKSHOP 6 MONTHS WARRANTY FOR THE PARTS INSTALLED BY US.
Vendedor: Milbrandt GmbH
Año de construcción: usado
Precio: 1.250 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Precio: 39.800 €
Ubicación: Land-one pcs used and  semi mobile concrete mixing plant 
elba esm 105

manufactory: elba
type: 105 va-cia
year of construction: 1990
capacity: 80 m³/hour
mixer: elba - one shaft mixer -  2m³
aggregate hoppers: 88t / per box
wheiging belt: fa. bleichert – 5000 kg
silos: 4 (2x 80t + 1x 50t+1x40t)
cement scale/dosage: 1000 kg 
water scale/dosage: 500 kg 
admixture / chemical scale: würschum 20 kg (kfw 5/12,5)

control unit: gedis ibs 33w + komdis - yoc 2007



location: east germany
available: immediate
price complete (as it/is it): 39.000,00 eur net/ex location

offer and all price are net and ex stock
without guarantee and/or guarantee, mistakes and/or false representations reserve, 
purchasing like see / how is it – standing or recumbent, subject prior sale
_________________________________________________________________
it is forbidden to copy or publicate this offer by any third partie or third person.
  ONE PCS USED AND SEMI MOBILE CONCRETE MIXING PLANT ELBA ESM 105 MANUFACTORY: ELBA TYPE: 105 VA-CIA YEAR OF CONSTRUCTION: 1990 CAPACITY: 80 M³/HOUR MIXER: ELBA - ONE SHAFT MIXER - 2M³ AGGREGATE HOPPERS: 88T / PER BOX WHEIGING BELT: FA. BLEICHERT – 5000 KG SILOS: 4 (2X 80T + 1X 50T+1X40T) CEMENT SCALE/DOSAGE: 1000 KG WATER SCALE/DOSAGE: 500 KG ADMIXTURE / CHEMICAL SCALE: WüRSCHUM 20 KG (KFW 5/12,5) CONTROL UNIT: GEDIS IBS 33W + KOMDIS - YOC 2007 LOCATION: EAST GERMANY AVAILABLE: IMMEDIATE PRICE COMPLETE (AS IT/IS IT): 39.000,00 EUR NET/EX LOCATION OFFER AND ALL PRICE ARE NET AND EX STOCK WITHOUT GUARANTEE AND/OR GUARANTEE, MISTAKES AND/OR FALSE REPRESENTATIONS RESERVE, PURCHASING LIKE SEE / HOW IS IT – STANDING OR RECUMBENT, SUBJECT PRIOR SALE _________________________________________________________________ IT IS FORBIDDEN TO COPY OR PUBLICATE THIS OFFER BY ANY THIRD PARTIE OR THIRD PERSON.
Vendedor: Sprenger Machinery - René Sprenger
Año de construcción: usado
Precio: 580 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Precio: 17.500 €
Ubicación: Land-
machine type machining center - vertical make hartford type vmc 1020 year 2000 control type cnc storage france country of origin taiwan delivery immediately cargo base ex work technical details
x way 1020 mm y way 510 mm z-way 510 mm table size 1200 x 600 mm speed range - milling 8000 rpm control fanuc omd drive performance - milling spindle 11 kw tool holder bt 40 number of tool magazine stations 20 stations feed range 1-10000 mm / min 
speed: 20 m / min total power consumption 25 kw machine weight 5500 kg space requirement approx. 2300 x 2200 x 2600 mm accessories full protection - fairing complete machine documentation control fanuc o md
 spindle bt 40 8000 rpm
 MACHINE TYPE MACHINING CENTER - VERTICAL MAKE HARTFORD TYPE VMC 1020 YEAR 2000 CONTROL TYPE CNC STORAGE FRANCE COUNTRY OF ORIGIN TAIWAN DELIVERY IMMEDIATELY CARGO BASE EX WORK TECHNICAL DETAILS X WAY 1020 MM Y WAY 510 MM Z-WAY 510 MM TABLE SIZE 1200 X 600 MM SPEED RANGE - MILLING 8000 RPM CONTROL FANUC OMD DRIVE PERFORMANCE - MILLING SPINDLE 11 KW TOOL HOLDER BT 40 NUMBER OF TOOL MAGAZINE STATIONS 20 STATIONS FEED RANGE 1-10000 MM / MIN SPEED: 20 M / MIN TOTAL POWER CONSUMPTION 25 KW MACHINE WEIGHT 5500 KG SPACE REQUIREMENT APPROX. 2300 X 2200 X 2600 MM ACCESSORIES FULL PROTECTION - FAIRING COMPLETE MACHINE DOCUMENTATION CONTROL FANUC O MD SPINDLE BT 40 8000 RPM
Vendedor: SOCIETE FIMOTEC
Año de construcción: usado
Precio: 80 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Precio: 15.500 €
Ubicación: Land-
machine type machining center - vertical make hartford type vmc 850 year 1998 control type cnc storage france country of origin taiwan delivery immediately cargo base ex work technical details

x trail 850 mm y way 510 mm z-way 510 mm table size 1000 x 450 mm speed range - milled 60-8000 rpm control fanuc omd drive performance - milling spindle 11 kw tool holder bt 40 number of tool magazine stations 20 stations feed range 1-10000 mm / m in speed: 20 m / min overall power requirements 20 kw machine weight approx. 4500 kg space requirement approx. 2300 x 2200 x 2600 mm accessories full protection - fairing complete machine documentation central lubrication rs 232 data interface central lubrication very nice
 cnc fanuc omd MACHINE TYPE MACHINING CENTER - VERTICAL MAKE HARTFORD TYPE VMC 850 YEAR 1998 CONTROL TYPE CNC STORAGE FRANCE COUNTRY OF ORIGIN TAIWAN DELIVERY IMMEDIATELY CARGO BASE EX WORK TECHNICAL DETAILS X TRAIL 850 MM Y WAY 510 MM Z-WAY 510 MM TABLE SIZE 1000 X 450 MM SPEED RANGE - MILLED 60-8000 RPM CONTROL FANUC OMD DRIVE PERFORMANCE - MILLING SPINDLE 11 KW TOOL HOLDER BT 40 NUMBER OF TOOL MAGAZINE STATIONS 20 STATIONS FEED RANGE 1-10000 MM / M IN SPEED: 20 M / MIN OVERALL POWER REQUIREMENTS 20 KW MACHINE WEIGHT APPROX. 4500 KG SPACE REQUIREMENT APPROX. 2300 X 2200 X 2600 MM ACCESSORIES FULL PROTECTION - FAIRING COMPLETE MACHINE DOCUMENTATION CENTRAL LUBRICATION RS 232 DATA INTERFACE CENTRAL LUBRICATION VERY NICE CNC FANUC OMD
Vendedor: SOCIETE FIMOTEC
Año de construcción: usado
Precio: 250 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Precio: 59.000 €
Ubicación: Land-d 104

1 miromatic bucket filling machine
with lid foil sealing
1 lane for buckets from 1 to 10 kg
capacity by 10 l buckets.  approx. 360 buckets/h
manufacturer is: fa. miromatic
manufacturer year is:  1999
mach. no. p295
type: mda-1-5/10-02

working principle:
the machine grab the empty buckets out of the 
magazine and bring the bucket in a headfirst
position, that water and disinfection solution can
be sprayed into the bucket 
after this cleaning the bucket is going into the 
filling station, after the bucket is turned back 
 
with a foil unrolled technique the lid foil will 
be cut into the right size for tho open bucket
one foil seal technique is following in the next 
station
the machine pick out of the lid magazine 
1 lid after the another, turned it to 180°
clean short the underside of the lid and 
spend it single into the lid slide.

in the next station the machine press the lid 
on the filled bucket and the outlet conveyor 
transport the bucket to the labelling station

after the label was spend on the lid the 
ready bucket will be palletized by hand.
the outlet transport conveyor has a length of 3,5 m
the outlet conveyor of the miromatic machine is 80 cm.

the electronic cabinet is installed on the righ side,
on the other side is installed the control panel,
type ibt miromatic 
on the top of the miromatic machine is installed the 
air filter and air sterilizing equipment 
in the aera of the manual bucket magazine filling 
place is installed a plastic strip curtain. in the top of 
these strip curtain is installed a air conditioning plant
(principle laminar flow) to keep away the bad air 
round about the filling machine place.

length of the miromatic filling machine is 5,8 m 
pus strip curtain place about 3 m
high of the miromatic  machine is 3,20 m.

price up standing point:			 59.000,00 euro





  D 104 1 MIROMATIC BUCKET FILLING MACHINE WITH LID FOIL SEALING 1 LANE FOR BUCKETS FROM 1 TO 10 KG CAPACITY BY 10 L BUCKETS. APPROX. 360 BUCKETS/H MANUFACTURER IS: FA. MIROMATIC MANUFACTURER YEAR IS: 1999 MACH. NO. P295 TYPE: MDA-1-5/10-02 WORKING PRINCIPLE: THE MACHINE GRAB THE EMPTY BUCKETS OUT OF THE MAGAZINE AND BRING THE BUCKET IN A HEADFIRST POSITION, THAT WATER AND DISINFECTION SOLUTION CAN BE SPRAYED INTO THE BUCKET AFTER THIS CLEANING THE BUCKET IS GOING INTO THE FILLING STATION, AFTER THE BUCKET IS TURNED BACK WITH A FOIL UNROLLED TECHNIQUE THE LID FOIL WILL BE CUT INTO THE RIGHT SIZE FOR THO OPEN BUCKET ONE FOIL SEAL TECHNIQUE IS FOLLOWING IN THE NEXT STATION THE MACHINE PICK OUT OF THE LID MAGAZINE 1 LID AFTER THE ANOTHER, TURNED IT TO 180° CLEAN SHORT THE UNDERSIDE OF THE LID AND SPEND IT SINGLE INTO THE LID SLIDE. IN THE NEXT STATION THE MACHINE PRESS THE LID ON THE FILLED BUCKET AND THE OUTLET CONVEYOR TRANSPORT THE BUCKET TO THE LABELLING STATION AFTER THE LABEL WAS SPEND ON THE LID THE READY BUCKET WILL BE PALLETIZED BY HAND. THE OUTLET TRANSPORT CONVEYOR HAS A LENGTH OF 3,5 M THE OUTLET CONVEYOR OF THE MIROMATIC MACHINE IS 80 CM. THE ELECTRONIC CABINET IS INSTALLED ON THE RIGH SIDE, ON THE OTHER SIDE IS INSTALLED THE CONTROL PANEL, TYPE IBT MIROMATIC ON THE TOP OF THE MIROMATIC MACHINE IS INSTALLED THE AIR FILTER AND AIR STERILIZING EQUIPMENT IN THE AERA OF THE MANUAL BUCKET MAGAZINE FILLING PLACE IS INSTALLED A PLASTIC STRIP CURTAIN. IN THE TOP OF THESE STRIP CURTAIN IS INSTALLED A AIR CONDITIONING PLANT (PRINCIPLE LAMINAR FLOW) TO KEEP AWAY THE BAD AIR ROUND ABOUT THE FILLING MACHINE PLACE. LENGTH OF THE MIROMATIC FILLING MACHINE IS 5,8 M PUS STRIP CURTAIN PLACE ABOUT 3 M HIGH OF THE MIROMATIC MACHINE IS 3,20 M. PRICE UP STANDING POINT: 59.000,00 EURO
Vendedor: LM Dairy Consulting
Año de construcción: usado
Precio: 175 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Precio: 6.500 €
Ubicación: Land-bj 01/1996
motor mde
480v
460kva
360kw
541a BJ 01/1996 MOTOR MDE 480V 460KVA 360KW 541A
Vendedor: EUROTECHNIK Dittrich GmbH
Año de construcción: usado
Precio: 220 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Año de construcción: usado
Ubicación: Land-bending length: 5100 mm
pressing force: 4000kn
hydraulic crowning
cybelec modeva 12s control
700mm stroke
weight: 48t
2 front attacks with parking position right and x + r axle
3 rear attacks with x + r axis.
2 front arms with r axis.
upper beam with scroll bars in t- and hydraulic. clamp, for various swords
incl. two different swords BENDING LENGTH: 5100 MM PRESSING FORCE: 4000KN HYDRAULIC CROWNING CYBELEC MODEVA 12S CONTROL 700MM STROKE WEIGHT: 48T 2 FRONT ATTACKS WITH PARKING POSITION RIGHT AND X + R AXLE 3 REAR ATTACKS WITH X + R AXIS. 2 FRONT ARMS WITH R AXIS. UPPER BEAM WITH SCROLL BARS IN T- AND HYDRAULIC. CLAMP, FOR VARIOUS SWORDS INCL. TWO DIFFERENT SWORDS "STRAIGHT" + "DEER FOOT" PTUVFE SWORDS WITH T-RECORDING FOR DIFFERENT RADIUS INSERTS TABLE WITH BAKER S RECORDING TABLE WITH PNEUMATICALLY RETRACTABLE SCROLL BARS FOR A LIGHT ROLL OF HEAVY DIES
Vendedor: H+S Maschinentechnik GmbH
Año de construcción: usado
Precio: 950 €
Ubicación: Land-de Germany, 26215 Wiefelstede
Vendedor: Theodor Eberlei GmbH & Co.KG
Usted no ha encontrado su máquina deseada? enviar consulta a todos los distribuidores (no hay registro necesario)
more MD types: