75 ofertas

Año de construcción: usado
Ubicación: Land-lake pictures LAKE PICTURES
Vendedor: Wermers Consultancy
Año de construcción: usado
Ubicación: Land-manufacturer bollegraaf<br/>type hbc 100<br/>year of construction 1991, 2017 overhauled<br/>hours of operation 40,586 hours<br/>press power main press 100 tons<br/>press power of pre-press 50 tons<br/>feed channel 1,600 x 1,100 mm (l x w)<br/>capacity per cycle time 3,15 m³<br/>theoretic cycle time 22 sec.<br/>bale size 750 x 1,100 mm, length variable<br/>driving motor 2 x 30 kw<br/>tying system 5 fold vertical, fully automatic<br/>throughput rate at a<br/>bulk weight of 30 kg/cbm up to 12 tons/h<br/>bulk weight of 50 kg/cbm up to 25 tons/h<br/>bulk weight of 100 kg/cbm up to 47 tons/h<br/>bale weight 550 up to 850 kg, depends on material<br/>volume hydraulic oil tank 1,200 l<br/>sps controller (manuf., type)  telemecanique tsx micro<br/>operating panel (manuf., type)  schneider magelis touch panel<br/>transport dimensions only baler 11,750 x 2,250 x 3,150 mm (l x w x h)<br/>machine weight baler approx. 30 tons<br/><br/>comments:<br/>the machine has been overhauled. the following work was carried out or parts were replaced.<br/>this press has been overhauled. following steps of repair and overhauling have been taken:<br/><br/>elder sps controls including enter and exit component assemblies were replaced by new controls of telemécanique tsx micro and the input commands in    the touch panel translated into russian.<br/>manual service push buttons were replaced by schneider tft touch panel 7,5? of type magelis.<br/>upper and lower light barriers including repeater (telco) have been renewed.<br/>the electric connection at hydraulic manifold is new, with partially renewed machine control cables and removal of needless connection.<br/>hydraulic oil tank has been emptied, cleaned and all filters were renewed.<br/>rubber gear for diminishing pressure between pumps and electric motors were renewed.<br/>pipes between high pressure part of the pump and hydraulic manifold have been renewed.<br/>cartridge cap on manifold has been sealed up newly.<br/>rubber buffers of pre-press flap are new.<br/>filling level indicator at tank has been renewed.<br/>measurement connections at hydraulic tank were altered.<br/>all flanges of hydraulic pipes have been sealed up newly.<br/>main cylinder, clam shell cylinder, needle cylinder and cylinder for wire core have all been sealed up newly.<br/>plunger of main cylinder, of clam shell cylinder and of needle cylinder have been ground and chrome-plated newly.<br/>all rollers and guide pulleys of press ram have been cleaned and loosened, the front rollers were renewed.<br/>wire guidance was cleaned and loosened, the back wire guidance rollers and wire core with pinhead rollers have been renewed.<br/>pinheads including blades have been reworked.<br/>hinges at press channel, on lateral parts and cap have been renewed.<br/>all hydraulic hoses of clam shell cylinders have been renewed.<br/><br/>inspections in russia, near moscow are possible after agreement.  we will not assume liability for the given technical data and possible errors. MANUFACTURER BOLLEGRAAF
TYPE HBC 100
YEAR OF CONSTRUCTION 1991, 2017 OVERHAULED
HOURS OF OPERATION 40,586 HOURS
PRESS POWER MAIN PRESS 100 TONS
PRESS POWER OF PRE-PRESS 50 TONS
FEED CHANNEL 1,600 X 1,100 MM (L X W)
CAPACITY PER CYCLE TIME 3,15 M³
THEORETIC CYCLE TIME 22 SEC.
BALE SIZE 750 X 1,100 MM, LENGTH VARIABLE
DRIVING MOTOR 2 X 30 KW
TYING SYSTEM 5 FOLD VERTICAL, FULLY AUTOMATIC
THROUGHPUT RATE AT A
BULK WEIGHT OF 30 KG/CBM UP TO 12 TONS/H
BULK WEIGHT OF 50 KG/CBM UP TO 25 TONS/H
BULK WEIGHT OF 100 KG/CBM UP TO 47 TONS/H
BALE WEIGHT 550 UP TO 850 KG, DEPENDS ON MATERIAL
VOLUME HYDRAULIC OIL TANK 1,200 L
SPS CONTROLLER (MANUF., TYPE) TELEMECANIQUE TSX MICRO
OPERATING PANEL (MANUF., TYPE) SCHNEIDER MAGELIS TOUCH PANEL
TRANSPORT DIMENSIONS ONLY BALER 11,750 X 2,250 X 3,150 MM (L X W X H)
MACHINE WEIGHT BALER APPROX. 30 TONS

COMMENTS:
THE MACHINE HAS BEEN OVERHAULED. THE FOLLOWING WORK WAS CARRIED OUT OR PARTS WERE REPLACED.
THIS PRESS HAS BEEN OVERHAULED. FOLLOWING STEPS OF REPAIR AND OVERHAULING HAVE BEEN TAKEN:

ELDER SPS CONTROLS INCLUDING ENTER AND EXIT COMPONENT ASSEMBLIES WERE REPLACED BY NEW CONTROLS OF TELEMéCANIQUE TSX MICRO AND THE INPUT COMMANDS IN THE TOUCH PANEL TRANSLATED INTO RUSSIAN.
MANUAL SERVICE PUSH BUTTONS WERE REPLACED BY SCHNEIDER TFT TOUCH PANEL 7,5? OF TYPE MAGELIS.
UPPER AND LOWER LIGHT BARRIERS INCLUDING REPEATER (TELCO) HAVE BEEN RENEWED.
THE ELECTRIC CONNECTION AT HYDRAULIC MANIFOLD IS NEW, WITH PARTIALLY RENEWED MACHINE CONTROL CABLES AND REMOVAL OF NEEDLESS CONNECTION.
HYDRAULIC OIL TANK HAS BEEN EMPTIED, CLEANED AND ALL FILTERS WERE RENEWED.
RUBBER GEAR FOR DIMINISHING PRESSURE BETWEEN PUMPS AND ELECTRIC MOTORS WERE RENEWED.
PIPES BETWEEN HIGH PRESSURE PART OF THE PUMP AND HYDRAULIC MANIFOLD HAVE BEEN RENEWED.
CARTRIDGE CAP ON MANIFOLD HAS BEEN SEALED UP NEWLY.
RUBBER BUFFERS OF PRE-PRESS FLAP ARE NEW.
FILLING LEVEL INDICATOR AT TANK HAS BEEN RENEWED.
MEASUREMENT CONNECTIONS AT HYDRAULIC TANK WERE ALTERED.
ALL FLANGES OF HYDRAULIC PIPES HAVE BEEN SEALED UP NEWLY.
MAIN CYLINDER, CLAM SHELL CYLINDER, NEEDLE CYLINDER AND CYLINDER FOR WIRE CORE HAVE ALL BEEN SEALED UP NEWLY.
PLUNGER OF MAIN CYLINDER, OF CLAM SHELL CYLINDER AND OF NEEDLE CYLINDER HAVE BEEN GROUND AND CHROME-PLATED NEWLY.
ALL ROLLERS AND GUIDE PULLEYS OF PRESS RAM HAVE BEEN CLEANED AND LOOSENED, THE FRONT ROLLERS WERE RENEWED.
WIRE GUIDANCE WAS CLEANED AND LOOSENED, THE BACK WIRE GUIDANCE ROLLERS AND WIRE CORE WITH PINHEAD ROLLERS HAVE BEEN RENEWED.
PINHEADS INCLUDING BLADES HAVE BEEN REWORKED.
HINGES AT PRESS CHANNEL, ON LATERAL PARTS AND CAP HAVE BEEN RENEWED.
ALL HYDRAULIC HOSES OF CLAM SHELL CYLINDERS HAVE BEEN RENEWED.

INSPECTIONS IN RUSSIA, NEAR MOSCOW ARE POSSIBLE AFTER AGREEMENT. WE WILL NOT ASSUME LIABILITY FOR THE GIVEN TECHNICAL DATA AND POSSIBLE ERRORS.
Vendedor: OBM Recycling Machinery B.V.
Año de construcción: usado
Ubicación: Land-original computer
central and side chromed air table
photocells
safety cover
books and electrichal draw ORIGINAL COMPUTER CENTRAL AND SIDE CHROMED AIR TABLE PHOTOCELLS SAFETY COVER BOOKS AND ELECTRICHAL DRAW
Vendedor: Tecnoffset S.r.l.
Año de construcción: usado
Precio: 250 €
Ubicación: Land-schneider electric nsx 160h, schneider electric nsx 100h, schneider electric nsx 100h, , socket box, fuse box, breaker cabinet SCHNEIDER ELECTRIC NSX 160H, SCHNEIDER ELECTRIC NSX 100H, SCHNEIDER ELECTRIC NSX 100H, , SOCKET BOX, FUSE BOX, BREAKER CABINET
Vendedor: DPX Power BV
Año de construcción: usado
Ubicación: Land-3 months la postpress warranty
excluding electronics

comprising:

horizon ht-30
three cutters

-use: solo (offline)
-technology: touch & work

-operation: stacks and cuts up to 10 copies at the same time and automatically
-cutting: knife works in two directions-> damage-free cuts
-storage: stack tray of sliced products

-order memory: 40 memory locations for repeat orders
-device: exact adjustment via touch screen

-construction: durable
-space: low
-edition number: small and medium runs

-format to cut:
max 320x235x51mm; min. 152x136x1mm; 

-cropped format:
max 305x230x51mm; min. 148x134x1mm; 

-trim:
max 99mm; min. 2mm

-before stack height: 300 mm

-power: max 520 books/h
-pressure: max 8kn
-noise: 70db

-dimensions: 2.350 1.160 x 1, 370mm
-electricity: 400v / 50 hz - 1, 25kw
-weight: 1.020kg

on request, we can organize for you the following points:

packing, loading, transport (by ship or airplane) including customs clearance 3 MONTHS LA POSTPRESS WARRANTY EXCLUDING ELECTRONICS COMPRISING: HORIZON HT-30 THREE CUTTERS -USE: SOLO (OFFLINE) -TECHNOLOGY: TOUCH & WORK -OPERATION: STACKS AND CUTS UP TO 10 COPIES AT THE SAME TIME AND AUTOMATICALLY -CUTTING: KNIFE WORKS IN TWO DIRECTIONS-> DAMAGE-FREE CUTS -STORAGE: STACK TRAY OF SLICED PRODUCTS -ORDER MEMORY: 40 MEMORY LOCATIONS FOR REPEAT ORDERS -DEVICE: EXACT ADJUSTMENT VIA TOUCH SCREEN -CONSTRUCTION: DURABLE -SPACE: LOW -EDITION NUMBER: SMALL AND MEDIUM RUNS -FORMAT TO CUT: MAX 320X235X51MM; MIN. 152X136X1MM; -CROPPED FORMAT: MAX 305X230X51MM; MIN. 148X134X1MM; -TRIM: MAX 99MM; MIN. 2MM -BEFORE STACK HEIGHT: 300 MM -POWER: MAX 520 BOOKS/H -PRESSURE: MAX 8KN -NOISE: 70DB -DIMENSIONS: 2.350 1.160 X 1, 370MM -ELECTRICITY: 400V / 50 HZ - 1, 25KW -WEIGHT: 1.020KG ON REQUEST, WE CAN ORGANIZE FOR YOU THE FOLLOWING POINTS: PACKING, LOADING, TRANSPORT (BY SHIP OR AIRPLANE) INCLUDING CUSTOMS CLEARANCE
Vendedor: LA-POSTPRESS Landauer Alexander
Año de construcción: usado
Precio: 250 €
Ubicación: Land-schneider electric nsx 160h, schneider electric nsx 100h, schneider electric nsx 100h, , socket box, fuse box, breaker cabinet SCHNEIDER ELECTRIC NSX 160H, SCHNEIDER ELECTRIC NSX 100H, SCHNEIDER ELECTRIC NSX 100H, , SOCKET BOX, FUSE BOX, BREAKER CABINET
Vendedor: DPX Power BV
Año de construcción: usado
Ubicación: Land-smartpac - complete automatic sachet filling and cartoning line for powders and granules, comprising the following: 

smartpac sp600 sachet machine, year 2010: 

- aps absolute v1 inkjet printer 
- servo driven 8 lane auger dosing system (smartpac) 
- 8 unit auger filler for powders (granules) 
- current configuration 4 lane = four double sachet 
- double sachet 140x125 mm (perforation between – sealing on all four sides) 
- max. 70 cycles per minute 
- only 5133 production hours 

smartpac pick & place 
- based on schneider electric elau pick and place robot 

heino ilsemann cmp-200l cartoner, year 2011 

- max 90 cycles per minute 
- largest carton box size used: 140x140x130mm = 25 double sachet 
- bar code reader pce touch terminal 
- leaflet folder guk fa21/4 
- wolke m600 advanced inkjet printer SMARTPAC - COMPLETE AUTOMATIC SACHET FILLING AND CARTONING LINE FOR POWDERS AND GRANULES, COMPRISING THE FOLLOWING: SMARTPAC SP600 SACHET MACHINE, YEAR 2010: - APS ABSOLUTE V1 INKJET PRINTER - SERVO DRIVEN 8 LANE AUGER DOSING SYSTEM (SMARTPAC) - 8 UNIT AUGER FILLER FOR POWDERS (GRANULES) - CURRENT CONFIGURATION 4 LANE = FOUR DOUBLE SACHET - DOUBLE SACHET 140X125 MM (PERFORATION BETWEEN – SEALING ON ALL FOUR SIDES) - MAX. 70 CYCLES PER MINUTE - ONLY 5133 PRODUCTION HOURS SMARTPAC PICK & PLACE - BASED ON SCHNEIDER ELECTRIC ELAU PICK AND PLACE ROBOT HEINO ILSEMANN CMP-200L CARTONER, YEAR 2011 - MAX 90 CYCLES PER MINUTE - LARGEST CARTON BOX SIZE USED: 140X140X130MM = 25 DOUBLE SACHET - BAR CODE READER PCE TOUCH TERMINAL - LEAFLET FOLDER GUK FA21/4 - WOLKE M600 ADVANCED INKJET PRINTER
Vendedor: Hauser Maschinen e.K.
Año de construcción: usado
Ubicación: Land-x-travel:900 mm<br/>y-travel:650 mm<br/>z-travel:450 mm<br/>table surface area:1235x460 mm<br/>t-slot (width-distance-quantity):18x80x5 mm<br/>max. table load:800 kg<br/>turning speed range:(27) 30 - 1800 u/min<br/>spindle nose:50 iso<br/>feed stepless:x/y/z:0-1000 / 0-1000 / 0-500 mm/min<br/>rapid traverse:x/y/z: 2200 / 2200 / 1100 mm/min<br/>power capacity:5,5 kw<br/>weight of the machine ca.:3600 kg<br/>machine size (lxwxh):1940x2200x2115 mm<br/>3-axis dro: <br/>universal milling head, manual: <br/>working lamp: <br/>ce and declaration of conformity: <br/>complete cooling unit: <br/>machine tools: <br/>screws cover: <br/>stepless feed:in allen achsen <br/>: <br/>european electric: <br/>: <br/>: <br/>metric, 400v 50hz 3 phase: <br/><br/>key features mounted inclusive price with 3-axis position indicator stable and rigid construction universal swivel head - cutters (huron) can be placed in any spatial angle large working range of up to 460x1235mm (optional 1635x500 mm 2000x500 mm) and up to 800/1.800 kg table load. turcite-b coating for smooth running of the axes vertical universal head can rotate 360 ??° for versatile cutting performance. x axis 900, 1300, 1500 mm vertical and horizontal spindle each with its own strong drive milling table pivotable in the x-axis array of standard accessories machine frame heavily ribbed and rigid wide, stable and hardened guides guarantee stability and lasting accuracy large, broadly supported table of ± 45 ° in the electrical equipment proven components from reputable manufacturers are used automatic feeds and rapid feeds in all 3 axes all hand wheels (for the x-axis) are placed on the front and accessible to the operator control panel can be positioned perfectly on pivoting boom the central lubrication ensures maintenance-free operation precision ground guideways with hardened surface for long-term stability and wear resistance. wide speed range (30-2050 / 27 steps)  standard accessories 3-axis position indicator universal milling automatic central lubrication sk 50 cutter tool shank Ø 32mm halogen lamp coolant system m24 tie rod, 2 pieces operating tool european electrical schneider or siemens aufsteckfräsdorn iso 50/27 mm aufsteckfräsdorn iso 50/40 mm operating instructions in german language ce version X-TRAVEL:900 MM
Y-TRAVEL:650 MM
Z-TRAVEL:450 MM
TABLE SURFACE AREA:1235X460 MM
T-SLOT (WIDTH-DISTANCE-QUANTITY):18X80X5 MM
MAX. TABLE LOAD:800 KG
TURNING SPEED RANGE:(27) 30 - 1800 U/MIN
SPINDLE NOSE:50 ISO
FEED STEPLESS:X/Y/Z:0-1000 / 0-1000 / 0-500 MM/MIN
RAPID TRAVERSE:X/Y/Z: 2200 / 2200 / 1100 MM/MIN
POWER CAPACITY:5,5 KW
WEIGHT OF THE MACHINE CA.:3600 KG
MACHINE SIZE (LXWXH):1940X2200X2115 MM
3-AXIS DRO:
UNIVERSAL MILLING HEAD, MANUAL:
WORKING LAMP:
CE AND DECLARATION OF CONFORMITY:
COMPLETE COOLING UNIT:
MACHINE TOOLS:
SCREWS COVER:
STEPLESS FEED:IN ALLEN ACHSEN
:
EUROPEAN ELECTRIC:
:
:
METRIC, 400V 50HZ 3 PHASE:

KEY FEATURES MOUNTED INCLUSIVE PRICE WITH 3-AXIS POSITION INDICATOR STABLE AND RIGID CONSTRUCTION UNIVERSAL SWIVEL HEAD - CUTTERS (HURON) CAN BE PLACED IN ANY SPATIAL ANGLE LARGE WORKING RANGE OF UP TO 460X1235MM (OPTIONAL 1635X500 MM 2000X500 MM) AND UP TO 800/1.800 KG TABLE LOAD. TURCITE-B COATING FOR SMOOTH RUNNING OF THE AXES VERTICAL UNIVERSAL HEAD CAN ROTATE 360 ??° FOR VERSATILE CUTTING PERFORMANCE. X AXIS 900, 1300, 1500 MM VERTICAL AND HORIZONTAL SPINDLE EACH WITH ITS OWN STRONG DRIVE MILLING TABLE PIVOTABLE IN THE X-AXIS ARRAY OF STANDARD ACCESSORIES MACHINE FRAME HEAVILY RIBBED AND RIGID WIDE, STABLE AND HARDENED GUIDES GUARANTEE STABILITY AND LASTING ACCURACY LARGE, BROADLY SUPPORTED TABLE OF ± 45 ° IN THE ELECTRICAL EQUIPMENT PROVEN COMPONENTS FROM REPUTABLE MANUFACTURERS ARE USED AUTOMATIC FEEDS AND RAPID FEEDS IN ALL 3 AXES ALL HAND WHEELS (FOR THE X-AXIS) ARE PLACED ON THE FRONT AND ACCESSIBLE TO THE OPERATOR CONTROL PANEL CAN BE POSITIONED PERFECTLY ON PIVOTING BOOM THE CENTRAL LUBRICATION ENSURES MAINTENANCE-FREE OPERATION PRECISION GROUND GUIDEWAYS WITH HARDENED SURFACE FOR LONG-TERM STABILITY AND WEAR RESISTANCE. WIDE SPEED RANGE (30-2050 / 27 STEPS) STANDARD ACCESSORIES 3-AXIS POSITION INDICATOR UNIVERSAL MILLING AUTOMATIC CENTRAL LUBRICATION SK 50 CUTTER TOOL SHANK Ø 32MM HALOGEN LAMP COOLANT SYSTEM M24 TIE ROD, 2 PIECES OPERATING TOOL EUROPEAN ELECTRICAL SCHNEIDER OR SIEMENS AUFSTECKFRäSDORN ISO 50/27 MM AUFSTECKFRäSDORN ISO 50/40 MM OPERATING INSTRUCTIONS IN GERMAN LANGUAGE CE VERSION
Vendedor: GK Werkzeugmaschinen GmbH
Año de construcción: usado
Ubicación: Land-machine type pur perfect binder

manufacturer newbind

model adventure p

year of construction 2009

condition as new (used) low meter reading

description

single-handed binder with electrically opening and closing pliers, binding length 120 to 380 mm spine thickness from 2 to 50 mm

processing of single sheets; equipped with a slot cutter, paper chip press suction, automatic transfer, speed 200 t / h, plc control

compressed air with socket required, closed application system for pur with slit nozzle, glue length control and integrated side gluing

refrigeration dryer hankinson type hhd 21, dimensions: hxwxd 392 x 320 x 320, volume flow: 20 mâ³ / h, weight: 29kg, 230v / 0, 21kw

reciprocating compressor schneider type 255-10-50 w dimensions: hxwxd 770 x 100 x 390, 10 bar / 1,5 kw / container 50 l / noise 87 db rms. delivery quantity: 165 l / min.

located germany

price on request MACHINE TYPE PUR PERFECT BINDER MANUFACTURER NEWBIND MODEL ADVENTURE P YEAR OF CONSTRUCTION 2009 CONDITION AS NEW (USED) LOW METER READING DESCRIPTION SINGLE-HANDED BINDER WITH ELECTRICALLY OPENING AND CLOSING PLIERS, BINDING LENGTH 120 TO 380 MM SPINE THICKNESS FROM 2 TO 50 MM PROCESSING OF SINGLE SHEETS; EQUIPPED WITH A SLOT CUTTER, PAPER CHIP PRESS SUCTION, AUTOMATIC TRANSFER, SPEED 200 T / H, PLC CONTROL COMPRESSED AIR WITH SOCKET REQUIRED, CLOSED APPLICATION SYSTEM FOR PUR WITH SLIT NOZZLE, GLUE LENGTH CONTROL AND INTEGRATED SIDE GLUING REFRIGERATION DRYER HANKINSON TYPE HHD 21, DIMENSIONS: HXWXD 392 X 320 X 320, VOLUME FLOW: 20 M&ACIRC;&SUP3; / H, WEIGHT: 29KG, 230V / 0, 21KW RECIPROCATING COMPRESSOR SCHNEIDER TYPE 255-10-50 W DIMENSIONS: HXWXD 770 X 100 X 390, 10 BAR / 1,5 KW / CONTAINER 50 L / NOISE 87 DB RMS. DELIVERY QUANTITY: 165 L / MIN. LOCATED GERMANY PRICE ON REQUEST
Vendedor: USED Machines
Año de construcción: usado
Ubicación: Land-faceplate diameter:1800 mm<br/>swing diameter:2000 mm<br/>turning height:1400 mm<br/>:8 t<br/>table speeds:3.2 - 100 m/min<br/>feed - turret head:1 - 500 mm/min<br/>vertical travel of ram:1000 mm<br/>transmission ratio:4 <br/>tool turret:4-fach, elektrisch programmierbar <br/>total power requirement:37 kw<br/>weight of the machine ca.:18 t<br/>dimensions of the machine ca.:4x4 m<br/>coolant system: <br/>4-pos electr. turret: <br/>chip conveyor:und -wagen <br/>spindle bearing:von nsk <br/>ce-design: <br/>technical documentation in german language: <br/>cnc control siemens 828:inkl. shopturn <br/>electrics from schneider or siemens: <br/>air conditioner for cabinet: <br/>machine semi-cover: <br/>telescope cover for guideways:von hema <br/>hydrostatic table: <br/>hydr. components:von kompass u.a. <br/>face plate:1800 mm<br/>stepless feed:in allen achsen <br/><br/>factory new cnc vertical lathe with siemens cnc control 828 and 4-way electric. tool holder.  warranty: 12 months on parts payment: 100% before loading  further information please refer to the system. FACEPLATE DIAMETER:1800 MM
SWING DIAMETER:2000 MM
TURNING HEIGHT:1400 MM
:8 T
TABLE SPEEDS:3.2 - 100 M/MIN
FEED - TURRET HEAD:1 - 500 MM/MIN
VERTICAL TRAVEL OF RAM:1000 MM
TRANSMISSION RATIO:4
TOOL TURRET:4-FACH, ELEKTRISCH PROGRAMMIERBAR
TOTAL POWER REQUIREMENT:37 KW
WEIGHT OF THE MACHINE CA.:18 T
DIMENSIONS OF THE MACHINE CA.:4X4 M
COOLANT SYSTEM:
4-POS ELECTR. TURRET:
CHIP CONVEYOR:UND -WAGEN
SPINDLE BEARING:VON NSK
CE-DESIGN:
TECHNICAL DOCUMENTATION IN GERMAN LANGUAGE:
CNC CONTROL SIEMENS 828:INKL. SHOPTURN
ELECTRICS FROM SCHNEIDER OR SIEMENS:
AIR CONDITIONER FOR CABINET:
MACHINE SEMI-COVER:
TELESCOPE COVER FOR GUIDEWAYS:VON HEMA
HYDROSTATIC TABLE:
HYDR. COMPONENTS:VON KOMPASS U.A.
FACE PLATE:1800 MM
STEPLESS FEED:IN ALLEN ACHSEN

FACTORY NEW CNC VERTICAL LATHE WITH SIEMENS CNC CONTROL 828 AND 4-WAY ELECTRIC. TOOL HOLDER. WARRANTY: 12 MONTHS ON PARTS PAYMENT: 100% BEFORE LOADING FURTHER INFORMATION PLEASE REFER TO THE SYSTEM.
Vendedor: GK Werkzeugmaschinen GmbH
Año de construcción: usado
Precio: 14.750 €
Ubicación: Land-we offer never used schneider tw 01 strapping machine for sale. ideal for use in the shipping trade, distribution and logistics centres

these machines operate with maintenance-free direct drives and ease of use.

basic equipment
â· extraction
â· automatic tape feeder
band scanning â·
-single - and auslauftaktung with connectors
â· color ral 5007 (brilliant blue)
â· speed infinitely adjustable table tape drive
â· short heat-up time
â· motors without a mechanical brake
â· plc control with four adjustable programs for
different products
â· adjustable reverse voltage
â· touchscreen, lockable through freely selectable code
â· to strapping counter
â· maintenance-free direct drives

technical data:

performance: up to 30 individual bands/minute / / up to 15 parallel straps per minute
width: 600 mm of maximum (with side ribbons) 460 mm min. 160 mm
height: 500 mm of max (with the press) 400 mm min. 30 mm max (without press)
package weight: 25 kg
to strapping material: polypropylene (pp band)
width: 5-12 mm thickness: 0.35 - 0,70 mm
type of closure: thermo welding cap
reel: core diameter: 200/228 mm
outer diameter: approx. 450 mm
width: 165-210 mm
electrics: 230 v, 1 phase, 50 hz
power: 1,1 kw 230v
pneumatic: operating pressure: 4 bar
usage: single machine: 90 l/min (3 l / strapping) free air
pressure: 200 n (cylinder diameter 25 mm)
tension: max 200 n
transport speed: approx. 26-59 m / min.
weight: approx. 360 kg (with package press)

price: â?¬14.750 net

delivery possible. please specify your postal code and directly ask.

offer is valid until stocks last.
mistakes and intermediate sale is reserved!

we have other facilities on offer:
sorter
wrapping and strapping machines
shelves
accessories
uvw.

we offer you against charge complex assembly, delivery, project creation, integration, planning according to your needs.
we are active throughout europe.

have to ask, are you looking for a solution for your warehouse you please contact with us. we speak german, english, french, russian and polish. WE OFFER NEVER USED SCHNEIDER TW 01 STRAPPING MACHINE FOR SALE. IDEAL FOR USE IN THE SHIPPING TRADE, DISTRIBUTION AND LOGISTICS CENTRES THESE MACHINES OPERATE WITH MAINTENANCE-FREE DIRECT DRIVES AND EASE OF USE. BASIC EQUIPMENT &ACIRC;&MIDDOT; EXTRACTION &ACIRC;&MIDDOT; AUTOMATIC TAPE FEEDER BAND SCANNING &ACIRC;&MIDDOT; -SINGLE - AND AUSLAUFTAKTUNG WITH CONNECTORS &ACIRC;&MIDDOT; COLOR RAL 5007 (BRILLIANT BLUE) &ACIRC;&MIDDOT; SPEED INFINITELY ADJUSTABLE TABLE TAPE DRIVE &ACIRC;&MIDDOT; SHORT HEAT-UP TIME &ACIRC;&MIDDOT; MOTORS WITHOUT A MECHANICAL BRAKE &ACIRC;&MIDDOT; PLC CONTROL WITH FOUR ADJUSTABLE PROGRAMS FOR DIFFERENT PRODUCTS &ACIRC;&MIDDOT; ADJUSTABLE REVERSE VOLTAGE &ACIRC;&MIDDOT; TOUCHSCREEN, LOCKABLE THROUGH FREELY SELECTABLE CODE &ACIRC;&MIDDOT; TO STRAPPING COUNTER &ACIRC;&MIDDOT; MAINTENANCE-FREE DIRECT DRIVES TECHNICAL DATA: PERFORMANCE: UP TO 30 INDIVIDUAL BANDS/MINUTE / / UP TO 15 PARALLEL STRAPS PER MINUTE WIDTH: 600 MM OF MAXIMUM (WITH SIDE RIBBONS) 460 MM MIN. 160 MM HEIGHT: 500 MM OF MAX (WITH THE PRESS) 400 MM MIN. 30 MM MAX (WITHOUT PRESS) PACKAGE WEIGHT: 25 KG TO STRAPPING MATERIAL: POLYPROPYLENE (PP BAND) WIDTH: 5-12 MM THICKNESS: 0.35 - 0,70 MM TYPE OF CLOSURE: THERMO WELDING CAP REEL: CORE DIAMETER: 200/228 MM OUTER DIAMETER: APPROX. 450 MM WIDTH: 165-210 MM ELECTRICS: 230 V, 1 PHASE, 50 HZ POWER: 1,1 KW 230V PNEUMATIC: OPERATING PRESSURE: 4 BAR USAGE: SINGLE MACHINE: 90 L/MIN (3 L / STRAPPING) FREE AIR PRESSURE: 200 N (CYLINDER DIAMETER 25 MM) TENSION: MAX 200 N TRANSPORT SPEED: APPROX. 26-59 M / MIN. WEIGHT: APPROX. 360 KG (WITH PACKAGE PRESS) PRICE: &ACIRC;?&NOT;14.750 NET DELIVERY POSSIBLE. PLEASE SPECIFY YOUR POSTAL CODE AND DIRECTLY ASK. OFFER IS VALID UNTIL STOCKS LAST. MISTAKES AND INTERMEDIATE SALE IS RESERVED! WE HAVE OTHER FACILITIES ON OFFER: SORTER WRAPPING AND STRAPPING MACHINES SHELVES ACCESSORIES UVW. WE OFFER YOU AGAINST CHARGE COMPLEX ASSEMBLY, DELIVERY, PROJECT CREATION, INTEGRATION, PLANNING ACCORDING TO YOUR NEEDS. WE ARE ACTIVE THROUGHOUT EUROPE. HAVE TO ASK, ARE YOU LOOKING FOR A SOLUTION FOR YOUR WAREHOUSE YOU PLEASE CONTACT WITH US. WE SPEAK GERMAN, ENGLISH, FRENCH, RUSSIAN AND POLISH.
Vendedor: Regalux GmbH
Año de construcción: usado
Ubicación: Land-turning diameter:1600 mm<br/>turning length:6000 mm<br/>control:siemens 828d <br/>max. swing over slide:1200 mm<br/>power requirement:22(30) kw<br/>weight of the machine ca.:12000 (3m) kg<br/>dimensions of the machine ca.:6000x2700x2300 mm<br/>4-jaw independent chuck:1000 mm<br/>automatic lubrication system: <br/>metric, 400v 50hz 3 phase: <br/>inverter and serovmotors for axes from siemens: <br/>cnc controller siemens 828:mit shopturn <br/>european electric:schneider, siemens <br/>machine semi-cover: <br/>machine bed one bed casting: <br/>technical documentation in german language: <br/>electronic hand wheel: <br/>technical documentation in german language: <br/>: <br/>leveling elements: <br/>ce-design: <br/>machine work light: <br/>heat exchanger:für den schaltschrank <br/><br/>warranty: 12 month payment: 100% before loading TURNING DIAMETER:1600 MM
TURNING LENGTH:6000 MM
CONTROL:SIEMENS 828D
MAX. SWING OVER SLIDE:1200 MM
POWER REQUIREMENT:22(30) KW
WEIGHT OF THE MACHINE CA.:12000 (3M) KG
DIMENSIONS OF THE MACHINE CA.:6000X2700X2300 MM
4-JAW INDEPENDENT CHUCK:1000 MM
AUTOMATIC LUBRICATION SYSTEM:
METRIC, 400V 50HZ 3 PHASE:
INVERTER AND SEROVMOTORS FOR AXES FROM SIEMENS:
CNC CONTROLLER SIEMENS 828:MIT SHOPTURN
EUROPEAN ELECTRIC:SCHNEIDER, SIEMENS
MACHINE SEMI-COVER:
MACHINE BED ONE BED CASTING:
TECHNICAL DOCUMENTATION IN GERMAN LANGUAGE:
ELECTRONIC HAND WHEEL:
TECHNICAL DOCUMENTATION IN GERMAN LANGUAGE:
:
LEVELING ELEMENTS:
CE-DESIGN:
MACHINE WORK LIGHT:
HEAT EXCHANGER:FüR DEN SCHALTSCHRANK

WARRANTY: 12 MONTH PAYMENT: 100% BEFORE LOADING
Vendedor: GK Werkzeugmaschinen GmbH
Año de construcción: usado
Precio: 14.750 €
Ubicación: Land-we offer never used schneider tv 02 strapping machine for sale. ideal for use in the shipping trade, distribution and logistics centres

these machines operate with maintenance-free direct drives and ease of use.

basic equipment
â· extraction
â· automatic tape feeder
band scanning â·
-single - and auslauftaktung with connectors
â· color ral 5007 (brilliant blue)
â· speed infinitely adjustable table tape drive
â· short heat-up time
â· motors without a mechanical brake
â· plc control with four adjustable programs for
different products
â· adjustable reverse voltage
â· touchscreen, lockable through freely selectable code
â· to strapping counter
â· maintenance-free direct drives

technical data:

performance: up to 30 individual bands/minute / / up to 15 parallel straps per minute
size of the pack material: width: 600 mm / / min. 160 mm
height: 650 mm of maximum (with the press) 550 mm min. 10 mm max (without press)
package weight: 25 kg
to strapping material: polypropylene (pp band)
width: 5-12 mm thickness: 0.35 - 0,70 mm
type of closure: thermo welding cap
reel: core diameter: 200/228 mm
outer diameter: approx. 450 mm
width: 165-210 mm
electrics: 230 v, 1 phase, 50 hz
power: 1,1 kw 230v
pneumatic: operating pressure: 4 bar
usage: single machine: 90 l/min (3 l / strapping) free air
pressure: 200 n (cylinder diameter 25 mm)
tension: max 200 n
transport speed: approx. 26-59 m / min.
weight: approx. 360 kg (with package press)

price: â?¬14.750 net

delivery possible. please specify your postal code and directly ask.

offer is valid until stocks last.
mistakes and intermediate sale is reserved!

we have other facilities on offer:
sorter
wrapping and strapping machines
shelves
accessories
uvw.

we offer you against charge complex assembly, delivery, project creation, integration, planning according to your needs.
we are active throughout europe.

have to ask, are you looking for a solution for your warehouse you please contact with us. we speak german, english, french, russian and polish. WE OFFER NEVER USED SCHNEIDER TV 02 STRAPPING MACHINE FOR SALE. IDEAL FOR USE IN THE SHIPPING TRADE, DISTRIBUTION AND LOGISTICS CENTRES THESE MACHINES OPERATE WITH MAINTENANCE-FREE DIRECT DRIVES AND EASE OF USE. BASIC EQUIPMENT &ACIRC;&MIDDOT; EXTRACTION &ACIRC;&MIDDOT; AUTOMATIC TAPE FEEDER BAND SCANNING &ACIRC;&MIDDOT; -SINGLE - AND AUSLAUFTAKTUNG WITH CONNECTORS &ACIRC;&MIDDOT; COLOR RAL 5007 (BRILLIANT BLUE) &ACIRC;&MIDDOT; SPEED INFINITELY ADJUSTABLE TABLE TAPE DRIVE &ACIRC;&MIDDOT; SHORT HEAT-UP TIME &ACIRC;&MIDDOT; MOTORS WITHOUT A MECHANICAL BRAKE &ACIRC;&MIDDOT; PLC CONTROL WITH FOUR ADJUSTABLE PROGRAMS FOR DIFFERENT PRODUCTS &ACIRC;&MIDDOT; ADJUSTABLE REVERSE VOLTAGE &ACIRC;&MIDDOT; TOUCHSCREEN, LOCKABLE THROUGH FREELY SELECTABLE CODE &ACIRC;&MIDDOT; TO STRAPPING COUNTER &ACIRC;&MIDDOT; MAINTENANCE-FREE DIRECT DRIVES TECHNICAL DATA: PERFORMANCE: UP TO 30 INDIVIDUAL BANDS/MINUTE / / UP TO 15 PARALLEL STRAPS PER MINUTE SIZE OF THE PACK MATERIAL: WIDTH: 600 MM / / MIN. 160 MM HEIGHT: 650 MM OF MAXIMUM (WITH THE PRESS) 550 MM MIN. 10 MM MAX (WITHOUT PRESS) PACKAGE WEIGHT: 25 KG TO STRAPPING MATERIAL: POLYPROPYLENE (PP BAND) WIDTH: 5-12 MM THICKNESS: 0.35 - 0,70 MM TYPE OF CLOSURE: THERMO WELDING CAP REEL: CORE DIAMETER: 200/228 MM OUTER DIAMETER: APPROX. 450 MM WIDTH: 165-210 MM ELECTRICS: 230 V, 1 PHASE, 50 HZ POWER: 1,1 KW 230V PNEUMATIC: OPERATING PRESSURE: 4 BAR USAGE: SINGLE MACHINE: 90 L/MIN (3 L / STRAPPING) FREE AIR PRESSURE: 200 N (CYLINDER DIAMETER 25 MM) TENSION: MAX 200 N TRANSPORT SPEED: APPROX. 26-59 M / MIN. WEIGHT: APPROX. 360 KG (WITH PACKAGE PRESS) PRICE: &ACIRC;?&NOT;14.750 NET DELIVERY POSSIBLE. PLEASE SPECIFY YOUR POSTAL CODE AND DIRECTLY ASK. OFFER IS VALID UNTIL STOCKS LAST. MISTAKES AND INTERMEDIATE SALE IS RESERVED! WE HAVE OTHER FACILITIES ON OFFER: SORTER WRAPPING AND STRAPPING MACHINES SHELVES ACCESSORIES UVW. WE OFFER YOU AGAINST CHARGE COMPLEX ASSEMBLY, DELIVERY, PROJECT CREATION, INTEGRATION, PLANNING ACCORDING TO YOUR NEEDS. WE ARE ACTIVE THROUGHOUT EUROPE. HAVE TO ASK, ARE YOU LOOKING FOR A SOLUTION FOR YOUR WAREHOUSE YOU PLEASE CONTACT WITH US. WE SPEAK GERMAN, ENGLISH, FRENCH, RUSSIAN AND POLISH.
Vendedor: Regalux GmbH
Año de construcción: usado
Ubicación: Land-faceplate diameter:5700 mm<br/>swing diameter:6300 mm<br/>turning height:4000 mm<br/>control:siemens 840d <br/>workpiece weight:80 t<br/>table speeds:0.4-40 (drehen) rpm<br/>table speeds:0.01-4 (fräsen) rpm<br/>max. torque:160 (am tisch) knm<br/>slide stroke:vertikal: 2000 mm<br/>slide stroke:horizontal: 3500 mm<br/>cross section of ram:300x300 mm<br/>rapid power traverse in x-and z direction:4 m/min<br/>feed stepless:0.1-500 mm/min<br/>cross rail travel :3000 mm<br/>rapid feed cross beam:310 mm/min<br/>drive motor for milling spindle:28 kw<br/>milling spindle - taper:50 iso<br/>main drive:90/110 kw<br/>weight of the machine ca.:175 t<br/>machine size (lxwxh):16.2×7.1×9.6 m<br/>total power requirement:230 kw<br/>: <br/>: <br/>worktool support (a-axis):1 stück für drehen, 1 stück für fräsen <br/>operating manual: <br/>control cabinet siemens plc:mit klimaanlage und siemens/schneider und omron elementen <br/>:1 stück<br/>rams:2 stück<br/>ce-design:verlängert die auslieferung um ca. 1 monat <br/>: <br/>european electric: <br/>scales:heidenhain <br/>servo motors:für achsen von siemens <br/>tabel encoder:heidenhain <br/>c-axis: <br/>4 jaw chuck:8 backen<br/>: <br/>telescope cover for guideways: <br/>automatic tool clamping:für die frässpindel <br/>workpiece measurement system: <br/>atc: <br/><br/>brand new vtl with c-axis and siemens controller 1. main application and construe feature the machine is three axes association with multi-function precision machine. it can realize the application of rough and finish machining for various materials like casting, forging, ferrous metal and non-ferrous metal as well as non-metal.  1.1 turning function: this machine tool is suitable to cut the materials of ferrous metal and non-ferrous metal as well as non-metal, by high speed steel tools and hard alloy tools, on the inner and outer cylindrical surfaces, inner and outer conical surfaces, rotating curved surface, flat surface, metric and british thread, spiral oil groove on the cylindrical face, etc., for the rough and fine turning. 1.2 milling, drilling and reaming: it can machine plane, part plane, groove on the plane. it can carry on milling, boring, drilling and reaming holes, thread holes and slant holes. it can also milling key slot on external and internal cylinder surface. 2. working condition 2.1 electrical power:  50hz±1hz?380v±10% 2.2 compressor air: 0.4~0.5mpa 2.3 temperature: 5?~40? 2.4 relative humidity:=85% 2.5 air dielectric: non-corrosive medium  3. design introduction the machine is double columns vertical model with advanced and reliable structure. sealing devices is for main spindle to aviod any coolant effection. long working time and high working capacity is by providing well material and percison manufacture.  indexing table is adopted for any position indexing.  4. main specification see above  5.1 main structure the machine structure adopts double columns with moveable crossrail and double toolheads. the structure consist of table base, main gearbox, gantry frame, crossrail, slider, toolhead, milling feeding gearbox, hydraulic system, platform, cnc system.  there are two vertical toolheads. the left one is for turning function, and the left one is turning and milling function. vertical movement of ram is inside of toolhead body. three axes association while milling function, two axes association can be achieved while turning function. horizontal feeding movement of toolhead is on the crossrail guideway. the crossrail is moving vertically to achieve differ high jobs.  5.2 table base casting iron material ht250 is for base with close frame structure by integrating casting and machining. the table is casted by 3 parts for convenience transportation. well scraping to ensure the movement stable against table guideway and base.  wear resistance material are adopted on the base guideway, and oil static pressure groove also adopts on the base guideway. the multi-points oil distributor is distributing the oil with constant flow oil for hydrostatic guideway. the radial direction biserial cylindrical roller bearings is adopted for table centering while at axle direction adopts pre-loading constant flow hydrostatic guideway with heavy load capacity. one more bearing is for limiting the table floating.  temperature sensor on the guideway measuring the guideway temperature, and temperature can be read on the operation panel. the table will stop while the temperature is over 60?. dc motor drives two shifts gearbox to drive table rotary movement, the high precision circular grating from heidenhain is mounted in the center of table.  dc servo motor drives table indexing by cog belt via gearbox to drive the table rotary movement. the milling indexing off while turning, and turning off while milling. the position encoder is mounted inside of main gearbox. the working table is designed with t-groove on the top surface based on the standards, with the arrangement of 8 jaws on it.  5.3 main gearbox  vertical spinlde structure for gearbox is driven by powerful ac motor. there is one floating shaft between two gears for gap elimation by oil pressure pushing. during milling function, the oil pressure to push the shaft up to pre-load to elimated the gap, and during turning function, the pressure is released to make the two gears working.  5.4 toolheads and sliders toolhead and ram are moving on the pre-load constant float hydrostatic guideway, and driven by ac servo motor by pre-load ballscrew nuts. toolhead moves along with crossrail guideway, and the relief beam will load the weight of toolhead. balance compensation also adopted in the cnc system. hydraulic balance system with the ram ensures the working accuracy. heidenhain optic scale is for toolhead moving full-closing loop positioning system for x and x1 axes. and semi-close loop controls ram moving system. the sectional area of the ram is in square; the rams are made from top quality steel alloy and treated by nitride hardening and finely ground. the section size is 300×300. the milling motor and gearbox are mounted on the top of right toolhead. the tools rotary is drive by the motor via the milling spindle inside of ram. the clamping and releasing device is mounted in the ram for easy changing the tools. the milling spindle is driven by siemens motor 28 kw 1000 rpm, and the driven system adopts siemens drive system.  the oil cylinder pushes 4 collects to realize auto clamping the attachments.  5.5 gantry frame ? gantry frame is consisting of right and left columns, top rail, connecting rail and screw transmission device, and high intensity, low stress for the main parts. the motor is mounted on the top rail, and it drives screw movement via worm gear box. connecting rail is welding part, and several times annealing treatment and releasing the stress to be done during manufacturing.   5.6 crossrail  crossrail is made of casting iron, and the guideway on crossrail has done the well scraping to ensure the accuracy. the relief beam and cnc compensation can ensure the toolhead accuracy movment. the clamping device principle is oil pressure for releasing and plate spring for clamping. the oil clamping station is mounted on the crossrail. crossrail guide and crossrail downwards column guide adopts stainless steel telescope protection cover. the oil return groove is allocated under the crossrail for oil return.  5.7 machine hydraulic system the machine hydraulic system is consist of lubrication system and hydrostatic system. the lubrication is automaticly controlled. machine hydrostatic system includes table hydrostatic guideway, slider hydrostatic guideway, ram hydrostatic guideway.  the oil supplied by multi-ponits pump with one pocket one pump to reduce the friction. it can achieve the high accuracy of the guideway.  2. electrical part 6.1 the machine adopts siemens 840dsl cnc control system for providing the standard cnc system arrangement with 10.4?lcd screem. (min. input value: 0.001mm; input increment: 0.001mm; max. programmable size: = + 99999.9mm; program memory =256 kbyte). 6.2the measuring element of cnc axis: liner optic scale for x axis, circular grating for c axis are full close loop, and servo motor with encoder for z axis is semi-close loop. 6.3:following function for cnc system: standard cnc function of 840dsl 3 axes association interpolation for milling function, and 2 axes association interpolation for turning function.  liner, circular and helix interpolation backlash compensation, thread pitch error compensation, system error compensation, over quad error compensation axis selection, manual operation, hand wheel, rapid and emergency stop are on the hand unit metric and inch screw turning function rs232 interface, usb interface, mdi programme input standard operation panel and machine operation panel dnc function 6.4 power display function for milling spindle 6.5self diagnose and monitoring system for machine to protect the cnc system, detail alarming list indicates the trouble spot. 6.6fully close air-condition electrical cabinet by using elements of omron, siemens, and schneider.  6.7electrical cabinet located at the right side behind the machine with socket and other ancillary facilities. safety caution light is equipped.  6.9 feeding per min and feeding per rotary, constant speed cutting function  6.10 siemens system for milling driven device 6.11 x?x1?z?z1 feed axes all use siemens 611d a.c servo motors. 6.12 main motor of milling head on the toolhead adopts siemens ac motor, and controlled by siemens speed regulation device.  3. machine accuracy standard of machine accuracy is according jb/t9934.1-1999. FACEPLATE DIAMETER:5700 MM
SWING DIAMETER:6300 MM
TURNING HEIGHT:4000 MM
CONTROL:SIEMENS 840D
WORKPIECE WEIGHT:80 T
TABLE SPEEDS:0.4-40 (DREHEN) RPM
TABLE SPEEDS:0.01-4 (FRäSEN) RPM
MAX. TORQUE:160 (AM TISCH) KNM
SLIDE STROKE:VERTIKAL: 2000 MM
SLIDE STROKE:HORIZONTAL: 3500 MM
CROSS SECTION OF RAM:300X300 MM
RAPID POWER TRAVERSE IN X-AND Z DIRECTION:4 M/MIN
FEED STEPLESS:0.1-500 MM/MIN
CROSS RAIL TRAVEL :3000 MM
RAPID FEED CROSS BEAM:310 MM/MIN
DRIVE MOTOR FOR MILLING SPINDLE:28 KW
MILLING SPINDLE - TAPER:50 ISO
MAIN DRIVE:90/110 KW
WEIGHT OF THE MACHINE CA.:175 T
MACHINE SIZE (LXWXH):16.2×7.1×9.6 M
TOTAL POWER REQUIREMENT:230 KW
:
:
WORKTOOL SUPPORT (A-AXIS):1 STüCK FüR DREHEN, 1 STüCK FüR FRäSEN
OPERATING MANUAL:
CONTROL CABINET SIEMENS PLC:MIT KLIMAANLAGE UND SIEMENS/SCHNEIDER UND OMRON ELEMENTEN
:1 STüCK
RAMS:2 STüCK
CE-DESIGN:VERLäNGERT DIE AUSLIEFERUNG UM CA. 1 MONAT
:
EUROPEAN ELECTRIC:
SCALES:HEIDENHAIN
SERVO MOTORS:FüR ACHSEN VON SIEMENS
TABEL ENCODER:HEIDENHAIN
C-AXIS:
4 JAW CHUCK:8 BACKEN
:
TELESCOPE COVER FOR GUIDEWAYS:
AUTOMATIC TOOL CLAMPING:FüR DIE FRäSSPINDEL
WORKPIECE MEASUREMENT SYSTEM:
ATC:

BRAND NEW VTL WITH C-AXIS AND SIEMENS CONTROLLER 1. MAIN APPLICATION AND CONSTRUE FEATURE THE MACHINE IS THREE AXES ASSOCIATION WITH MULTI-FUNCTION PRECISION MACHINE. IT CAN REALIZE THE APPLICATION OF ROUGH AND FINISH MACHINING FOR VARIOUS MATERIALS LIKE CASTING, FORGING, FERROUS METAL AND NON-FERROUS METAL AS WELL AS NON-METAL. 1.1 TURNING FUNCTION: THIS MACHINE TOOL IS SUITABLE TO CUT THE MATERIALS OF FERROUS METAL AND NON-FERROUS METAL AS WELL AS NON-METAL, BY HIGH SPEED STEEL TOOLS AND HARD ALLOY TOOLS, ON THE INNER AND OUTER CYLINDRICAL SURFACES, INNER AND OUTER CONICAL SURFACES, ROTATING CURVED SURFACE, FLAT SURFACE, METRIC AND BRITISH THREAD, SPIRAL OIL GROOVE ON THE CYLINDRICAL FACE, ETC., FOR THE ROUGH AND FINE TURNING. 1.2 MILLING, DRILLING AND REAMING: IT CAN MACHINE PLANE, PART PLANE, GROOVE ON THE PLANE. IT CAN CARRY ON MILLING, BORING, DRILLING AND REAMING HOLES, THREAD HOLES AND SLANT HOLES. IT CAN ALSO MILLING KEY SLOT ON EXTERNAL AND INTERNAL CYLINDER SURFACE. 2. WORKING CONDITION 2.1 ELECTRICAL POWER: 50HZ±1HZ?380V±10% 2.2 COMPRESSOR AIR: 0.4~0.5MPA 2.3 TEMPERATURE: 5?~40? 2.4 RELATIVE HUMIDITY:=85% 2.5 AIR DIELECTRIC: NON-CORROSIVE MEDIUM 3. DESIGN INTRODUCTION THE MACHINE IS DOUBLE COLUMNS VERTICAL MODEL WITH ADVANCED AND RELIABLE STRUCTURE. SEALING DEVICES IS FOR MAIN SPINDLE TO AVIOD ANY COOLANT EFFECTION. LONG WORKING TIME AND HIGH WORKING CAPACITY IS BY PROVIDING WELL MATERIAL AND PERCISON MANUFACTURE. INDEXING TABLE IS ADOPTED FOR ANY POSITION INDEXING. 4. MAIN SPECIFICATION SEE ABOVE 5.1 MAIN STRUCTURE THE MACHINE STRUCTURE ADOPTS DOUBLE COLUMNS WITH MOVEABLE CROSSRAIL AND DOUBLE TOOLHEADS. THE STRUCTURE CONSIST OF TABLE BASE, MAIN GEARBOX, GANTRY FRAME, CROSSRAIL, SLIDER, TOOLHEAD, MILLING FEEDING GEARBOX, HYDRAULIC SYSTEM, PLATFORM, CNC SYSTEM. THERE ARE TWO VERTICAL TOOLHEADS. THE LEFT ONE IS FOR TURNING FUNCTION, AND THE LEFT ONE IS TURNING AND MILLING FUNCTION. VERTICAL MOVEMENT OF RAM IS INSIDE OF TOOLHEAD BODY. THREE AXES ASSOCIATION WHILE MILLING FUNCTION, TWO AXES ASSOCIATION CAN BE ACHIEVED WHILE TURNING FUNCTION. HORIZONTAL FEEDING MOVEMENT OF TOOLHEAD IS ON THE CROSSRAIL GUIDEWAY. THE CROSSRAIL IS MOVING VERTICALLY TO ACHIEVE DIFFER HIGH JOBS. 5.2 TABLE BASE CASTING IRON MATERIAL HT250 IS FOR BASE WITH CLOSE FRAME STRUCTURE BY INTEGRATING CASTING AND MACHINING. THE TABLE IS CASTED BY 3 PARTS FOR CONVENIENCE TRANSPORTATION. WELL SCRAPING TO ENSURE THE MOVEMENT STABLE AGAINST TABLE GUIDEWAY AND BASE. WEAR RESISTANCE MATERIAL ARE ADOPTED ON THE BASE GUIDEWAY, AND OIL STATIC PRESSURE GROOVE ALSO ADOPTS ON THE BASE GUIDEWAY. THE MULTI-POINTS OIL DISTRIBUTOR IS DISTRIBUTING THE OIL WITH CONSTANT FLOW OIL FOR HYDROSTATIC GUIDEWAY. THE RADIAL DIRECTION BISERIAL CYLINDRICAL ROLLER BEARINGS IS ADOPTED FOR TABLE CENTERING WHILE AT AXLE DIRECTION ADOPTS PRE-LOADING CONSTANT FLOW HYDROSTATIC GUIDEWAY WITH HEAVY LOAD CAPACITY. ONE MORE BEARING IS FOR LIMITING THE TABLE FLOATING. TEMPERATURE SENSOR ON THE GUIDEWAY MEASURING THE GUIDEWAY TEMPERATURE, AND TEMPERATURE CAN BE READ ON THE OPERATION PANEL. THE TABLE WILL STOP WHILE THE TEMPERATURE IS OVER 60?. DC MOTOR DRIVES TWO SHIFTS GEARBOX TO DRIVE TABLE ROTARY MOVEMENT, THE HIGH PRECISION CIRCULAR GRATING FROM HEIDENHAIN IS MOUNTED IN THE CENTER OF TABLE. DC SERVO MOTOR DRIVES TABLE INDEXING BY COG BELT VIA GEARBOX TO DRIVE THE TABLE ROTARY MOVEMENT. THE MILLING INDEXING OFF WHILE TURNING, AND TURNING OFF WHILE MILLING. THE POSITION ENCODER IS MOUNTED INSIDE OF MAIN GEARBOX. THE WORKING TABLE IS DESIGNED WITH T-GROOVE ON THE TOP SURFACE BASED ON THE STANDARDS, WITH THE ARRANGEMENT OF 8 JAWS ON IT. 5.3 MAIN GEARBOX VERTICAL SPINLDE STRUCTURE FOR GEARBOX IS DRIVEN BY POWERFUL AC MOTOR. THERE IS ONE FLOATING SHAFT BETWEEN TWO GEARS FOR GAP ELIMATION BY OIL PRESSURE PUSHING. DURING MILLING FUNCTION, THE OIL PRESSURE TO PUSH THE SHAFT UP TO PRE-LOAD TO ELIMATED THE GAP, AND DURING TURNING FUNCTION, THE PRESSURE IS RELEASED TO MAKE THE TWO GEARS WORKING. 5.4 TOOLHEADS AND SLIDERS TOOLHEAD AND RAM ARE MOVING ON THE PRE-LOAD CONSTANT FLOAT HYDROSTATIC GUIDEWAY, AND DRIVEN BY AC SERVO MOTOR BY PRE-LOAD BALLSCREW NUTS. TOOLHEAD MOVES ALONG WITH CROSSRAIL GUIDEWAY, AND THE RELIEF BEAM WILL LOAD THE WEIGHT OF TOOLHEAD. BALANCE COMPENSATION ALSO ADOPTED IN THE CNC SYSTEM. HYDRAULIC BALANCE SYSTEM WITH THE RAM ENSURES THE WORKING ACCURACY. HEIDENHAIN OPTIC SCALE IS FOR TOOLHEAD MOVING FULL-CLOSING LOOP POSITIONING SYSTEM FOR X AND X1 AXES. AND SEMI-CLOSE LOOP CONTROLS RAM MOVING SYSTEM. THE SECTIONAL AREA OF THE RAM IS IN SQUARE; THE RAMS ARE MADE FROM TOP QUALITY STEEL ALLOY AND TREATED BY NITRIDE HARDENING AND FINELY GROUND. THE SECTION SIZE IS 300×300. THE MILLING MOTOR AND GEARBOX ARE MOUNTED ON THE TOP OF RIGHT TOOLHEAD. THE TOOLS ROTARY IS DRIVE BY THE MOTOR VIA THE MILLING SPINDLE INSIDE OF RAM. THE CLAMPING AND RELEASING DEVICE IS MOUNTED IN THE RAM FOR EASY CHANGING THE TOOLS. THE MILLING SPINDLE IS DRIVEN BY SIEMENS MOTOR 28 KW 1000 RPM, AND THE DRIVEN SYSTEM ADOPTS SIEMENS DRIVE SYSTEM. THE OIL CYLINDER PUSHES 4 COLLECTS TO REALIZE AUTO CLAMPING THE ATTACHMENTS. 5.5 GANTRY FRAME ? GANTRY FRAME IS CONSISTING OF RIGHT AND LEFT COLUMNS, TOP RAIL, CONNECTING RAIL AND SCREW TRANSMISSION DEVICE, AND HIGH INTENSITY, LOW STRESS FOR THE MAIN PARTS. THE MOTOR IS MOUNTED ON THE TOP RAIL, AND IT DRIVES SCREW MOVEMENT VIA WORM GEAR BOX. CONNECTING RAIL IS WELDING PART, AND SEVERAL TIMES ANNEALING TREATMENT AND RELEASING THE STRESS TO BE DONE DURING MANUFACTURING. 5.6 CROSSRAIL CROSSRAIL IS MADE OF CASTING IRON, AND THE GUIDEWAY ON CROSSRAIL HAS DONE THE WELL SCRAPING TO ENSURE THE ACCURACY. THE RELIEF BEAM AND CNC COMPENSATION CAN ENSURE THE TOOLHEAD ACCURACY MOVMENT. THE CLAMPING DEVICE PRINCIPLE IS OIL PRESSURE FOR RELEASING AND PLATE SPRING FOR CLAMPING. THE OIL CLAMPING STATION IS MOUNTED ON THE CROSSRAIL. CROSSRAIL GUIDE AND CROSSRAIL DOWNWARDS COLUMN GUIDE ADOPTS STAINLESS STEEL TELESCOPE PROTECTION COVER. THE OIL RETURN GROOVE IS ALLOCATED UNDER THE CROSSRAIL FOR OIL RETURN. 5.7 MACHINE HYDRAULIC SYSTEM THE MACHINE HYDRAULIC SYSTEM IS CONSIST OF LUBRICATION SYSTEM AND HYDROSTATIC SYSTEM. THE LUBRICATION IS AUTOMATICLY CONTROLLED. MACHINE HYDROSTATIC SYSTEM INCLUDES TABLE HYDROSTATIC GUIDEWAY, SLIDER HYDROSTATIC GUIDEWAY, RAM HYDROSTATIC GUIDEWAY. THE OIL SUPPLIED BY MULTI-PONITS PUMP WITH ONE POCKET ONE PUMP TO REDUCE THE FRICTION. IT CAN ACHIEVE THE HIGH ACCURACY OF THE GUIDEWAY. 2. ELECTRICAL PART 6.1 THE MACHINE ADOPTS SIEMENS 840DSL CNC CONTROL SYSTEM FOR PROVIDING THE STANDARD CNC SYSTEM ARRANGEMENT WITH 10.4?LCD SCREEM. (MIN. INPUT VALUE: 0.001MM; INPUT INCREMENT: 0.001MM; MAX. PROGRAMMABLE SIZE: = + 99999.9MM; PROGRAM MEMORY =256 KBYTE). 6.2THE MEASURING ELEMENT OF CNC AXIS: LINER OPTIC SCALE FOR X AXIS, CIRCULAR GRATING FOR C AXIS ARE FULL CLOSE LOOP, AND SERVO MOTOR WITH ENCODER FOR Z AXIS IS SEMI-CLOSE LOOP. 6.3:FOLLOWING FUNCTION FOR CNC SYSTEM: STANDARD CNC FUNCTION OF 840DSL 3 AXES ASSOCIATION INTERPOLATION FOR MILLING FUNCTION, AND 2 AXES ASSOCIATION INTERPOLATION FOR TURNING FUNCTION. LINER, CIRCULAR AND HELIX INTERPOLATION BACKLASH COMPENSATION, THREAD PITCH ERROR COMPENSATION, SYSTEM ERROR COMPENSATION, OVER QUAD ERROR COMPENSATION AXIS SELECTION, MANUAL OPERATION, HAND WHEEL, RAPID AND EMERGENCY STOP ARE ON THE HAND UNIT METRIC AND INCH SCREW TURNING FUNCTION RS232 INTERFACE, USB INTERFACE, MDI PROGRAMME INPUT STANDARD OPERATION PANEL AND MACHINE OPERATION PANEL DNC FUNCTION 6.4 POWER DISPLAY FUNCTION FOR MILLING SPINDLE 6.5SELF DIAGNOSE AND MONITORING SYSTEM FOR MACHINE TO PROTECT THE CNC SYSTEM, DETAIL ALARMING LIST INDICATES THE TROUBLE SPOT. 6.6FULLY CLOSE AIR-CONDITION ELECTRICAL CABINET BY USING ELEMENTS OF OMRON, SIEMENS, AND SCHNEIDER. 6.7ELECTRICAL CABINET LOCATED AT THE RIGHT SIDE BEHIND THE MACHINE WITH SOCKET AND OTHER ANCILLARY FACILITIES. SAFETY CAUTION LIGHT IS EQUIPPED. 6.9 FEEDING PER MIN AND FEEDING PER ROTARY, CONSTANT SPEED CUTTING FUNCTION 6.10 SIEMENS SYSTEM FOR MILLING DRIVEN DEVICE 6.11 X?X1?Z?Z1 FEED AXES ALL USE SIEMENS 611D A.C SERVO MOTORS. 6.12 MAIN MOTOR OF MILLING HEAD ON THE TOOLHEAD ADOPTS SIEMENS AC MOTOR, AND CONTROLLED BY SIEMENS SPEED REGULATION DEVICE. 3. MACHINE ACCURACY STANDARD OF MACHINE ACCURACY IS ACCORDING JB/T9934.1-1999.
Vendedor: GK Werkzeugmaschinen GmbH
Año de construcción: usado
Precio: 1.759 €
Ubicación: Land-schneider electric integrated. servomotor-1.7 nm 6000 rpm - multip.drehung - o.bremse nominal auxiliary voltage [uh, nom] 250... 700 v continuous current at standstill 2.5 a continuous standstill torque 1.7 nm peak stillstand torque 7.6 nm rated power at the output of 720 w rated torque 1.15 nm nominal speed 6000 rpm max power irms 11.8 a rated current [in] 1,5 a shaft end smooth second shaft without second shaft end shaft diameter 11 mm wavelength 23 mm width feather 18 mm type of feedback absolutely sincos hiperface multi turn resolution speed feedback 128 periods without holding brake mounting bracket of international standard flange motor flange size 70 mm torque constant 0.76 nm/afor 120 â° c back-emf constant 48 v / krpmbei 20 â° c number of motor pole 6 SCHNEIDER ELECTRIC INTEGRATED. SERVOMOTOR-1.7 NM 6000 RPM - MULTIP.DREHUNG - O.BREMSE NOMINAL AUXILIARY VOLTAGE [UH, NOM] 250... 700 V CONTINUOUS CURRENT AT STANDSTILL 2.5 A CONTINUOUS STANDSTILL TORQUE 1.7 NM PEAK STILLSTAND TORQUE 7.6 NM RATED POWER AT THE OUTPUT OF 720 W RATED TORQUE 1.15 NM NOMINAL SPEED 6000 RPM MAX POWER IRMS 11.8 A RATED CURRENT [IN] 1,5 A SHAFT END SMOOTH SECOND SHAFT WITHOUT SECOND SHAFT END SHAFT DIAMETER 11 MM WAVELENGTH 23 MM WIDTH FEATHER 18 MM TYPE OF FEEDBACK ABSOLUTELY SINCOS HIPERFACE MULTI TURN RESOLUTION SPEED FEEDBACK 128 PERIODS WITHOUT HOLDING BRAKE MOUNTING BRACKET OF INTERNATIONAL STANDARD FLANGE MOTOR FLANGE SIZE 70 MM TORQUE CONSTANT 0.76 NM/AFOR 120 &ACIRC;&DEG; C BACK-EMF CONSTANT 48 V / KRPMBEI 20 &ACIRC;&DEG; C NUMBER OF MOTOR POLE 6
Vendedor: KRASTEV EX-IMPORT
Año de construcción: usado
Ubicación: Land-x-travel:1200 mm<br/>y-travel:700 mm<br/>z-travel:500 mm<br/>:500 x 1600 mm mm<br/>max. table load:1800 kg<br/>t-slot (width-distance-quantity):5 x 18 x 80 mm<br/>spindle taper:50 iso<br/>turning speed range:(27 stufen) 30 - 2050 u/min<br/>distance spindle nose and table:25? 525 mm<br/>feeds:x/y/z: 0-1000 / 0-1000 / 0-500 mm/min<br/>rapid travel x/y/z:2200 / 2200 / 1100 mm/min<br/>power capacity:7,5 kw<br/>weight of the machine ca.:5 t<br/>machine dimensions lxwxh:2475 x 2260 x 2180 mm<br/>universal milling head:manuell schwenkbar, 360° <br/>dro:3-achsen <br/>central lubrication: <br/>halogen lamp: <br/>: <br/>european electric:im wesentlichen schneider <br/>: <br/>ce-design: <br/>: <br/>servo motors:in allen achsen <br/>screws cover: <br/>draw bar: <br/>machine tools: <br/>machine vice: <br/>round table, manual : <br/>milling and boring equipment: <br/><br/>100 % before loading  warranty: none  one used knee and column milling machine-universal, make union bielefeld, type usf 4, baujahr 1970, maschinen-nr. 55/214 X-TRAVEL:1200 MM
Y-TRAVEL:700 MM
Z-TRAVEL:500 MM
:500 X 1600 MM MM
MAX. TABLE LOAD:1800 KG
T-SLOT (WIDTH-DISTANCE-QUANTITY):5 X 18 X 80 MM
SPINDLE TAPER:50 ISO
TURNING SPEED RANGE:(27 STUFEN) 30 - 2050 U/MIN
DISTANCE SPINDLE NOSE AND TABLE:25? 525 MM
FEEDS:X/Y/Z: 0-1000 / 0-1000 / 0-500 MM/MIN
RAPID TRAVEL X/Y/Z:2200 / 2200 / 1100 MM/MIN
POWER CAPACITY:7,5 KW
WEIGHT OF THE MACHINE CA.:5 T
MACHINE DIMENSIONS LXWXH:2475 X 2260 X 2180 MM
UNIVERSAL MILLING HEAD:MANUELL SCHWENKBAR, 360°
DRO:3-ACHSEN
CENTRAL LUBRICATION:
HALOGEN LAMP:
:
EUROPEAN ELECTRIC:IM WESENTLICHEN SCHNEIDER
:
CE-DESIGN:
:
SERVO MOTORS:IN ALLEN ACHSEN
SCREWS COVER:
DRAW BAR:
MACHINE TOOLS:
MACHINE VICE:
ROUND TABLE, MANUAL :
MILLING AND BORING EQUIPMENT:

100 % BEFORE LOADING WARRANTY: NONE ONE USED KNEE AND COLUMN MILLING MACHINE-UNIVERSAL, MAKE UNION BIELEFELD, TYPE USF 4, BAUJAHR 1970, MASCHINEN-NR. 55/214
Vendedor: GK Werkzeugmaschinen GmbH
Año de construcción: usado
Precio: 1.759 €
Ubicación: Land-schneider electric integrated. servomotor-2.2 nm 6000 rpm - multip.drehung - m.bremse nominal auxiliary voltage [uh, nom] 250... 700 v continuous current at standstill 3 a continuous standstill torque 2,2 nm peak stillstand torque 8.7 nm rated power at the output of 720 w rated torque 1.15 nm nominal speed 6000 rpm max power irms 12 a rated current [in] 1,5 a shaft end smooth second wave without second shaft end shaft diameter 14 mm wavelength 30 mm width feather 20 mm type of feedback absolutely sincos hiperface multi turn resolution speed feedback 128 periods holding brake with holding torque 3 nm (parking brake) mounting bracket of international standard flange motor flange size 70 mm torque constant 0.76 nm/afor 120 â° c back-emf constant 49 v / krpmbei 20 â° c number of motor pole 6 SCHNEIDER ELECTRIC INTEGRATED. SERVOMOTOR-2.2 NM 6000 RPM - MULTIP.DREHUNG - M.BREMSE NOMINAL AUXILIARY VOLTAGE [UH, NOM] 250... 700 V CONTINUOUS CURRENT AT STANDSTILL 3 A CONTINUOUS STANDSTILL TORQUE 2,2 NM PEAK STILLSTAND TORQUE 8.7 NM RATED POWER AT THE OUTPUT OF 720 W RATED TORQUE 1.15 NM NOMINAL SPEED 6000 RPM MAX POWER IRMS 12 A RATED CURRENT [IN] 1,5 A SHAFT END SMOOTH SECOND WAVE WITHOUT SECOND SHAFT END SHAFT DIAMETER 14 MM WAVELENGTH 30 MM WIDTH FEATHER 20 MM TYPE OF FEEDBACK ABSOLUTELY SINCOS HIPERFACE MULTI TURN RESOLUTION SPEED FEEDBACK 128 PERIODS HOLDING BRAKE WITH HOLDING TORQUE 3 NM (PARKING BRAKE) MOUNTING BRACKET OF INTERNATIONAL STANDARD FLANGE MOTOR FLANGE SIZE 70 MM TORQUE CONSTANT 0.76 NM/AFOR 120 &ACIRC;&DEG; C BACK-EMF CONSTANT 49 V / KRPMBEI 20 &ACIRC;&DEG; C NUMBER OF MOTOR POLE 6
Vendedor: KRASTEV EX-IMPORT
Año de construcción: usado
Ubicación: Land-faceplate diameter:8000 mm<br/>swing diameter:10000 mm<br/>turning height:4500 mm<br/>workpiece weight:120/200 t<br/>table speeds:0.2-16 u/min (2 stufen) <br/>max. torque on the faceplate:200/460  k.nm<br/>slide stroke:vertikal: 2300 mm<br/>slide stroke:horizontal: 5300 mm<br/>cross section of ram:300x300 mm<br/>max. cutting force of tool head :links: 63 kn / rechts: 80 kn <br/>cross rail travel :2000 mm<br/>rapid feed cross beam:300 mm/min<br/>feed stepless:x-achse: 1-500 mm/min<br/>main drive:110 kw<br/>weight of the machine ca.:270 t<br/>machine size (lxwxh):14000x10000x9000 mm<br/>control:siemens 828d/siemens 840d <br/>: <br/>: <br/>: <br/>workbench: <br/>: <br/>worktool support (a-axis):2 stück<br/>operating manual: <br/>control cabinet siemens plc: <br/>: <br/>: <br/>:1 stück<br/>rams:1 stück konventioneller und 1 stück cnc-stößel <br/>ce-design:inkl. zertifikat <br/>: <br/>european electric:schneider, siemens, abb oder ähnlich <br/>4 jaw chuck: <br/>servo motors:von siemens <br/>sps machine control:von siemens <br/>linear scales: <br/>workpiece measurement system: <br/>c-axis: <br/>cnc controls from:siemens/fanuc/fagor <br/>turret: <br/>tool measuring system: <br/>semi guarding: <br/><br/>for more information please check attached pdf file on the right hand side FACEPLATE DIAMETER:8000 MM
SWING DIAMETER:10000 MM
TURNING HEIGHT:4500 MM
WORKPIECE WEIGHT:120/200 T
TABLE SPEEDS:0.2-16 U/MIN (2 STUFEN)
MAX. TORQUE ON THE FACEPLATE:200/460 K.NM
SLIDE STROKE:VERTIKAL: 2300 MM
SLIDE STROKE:HORIZONTAL: 5300 MM
CROSS SECTION OF RAM:300X300 MM
MAX. CUTTING FORCE OF TOOL HEAD :LINKS: 63 KN / RECHTS: 80 KN
CROSS RAIL TRAVEL :2000 MM
RAPID FEED CROSS BEAM:300 MM/MIN
FEED STEPLESS:X-ACHSE: 1-500 MM/MIN
MAIN DRIVE:110 KW
WEIGHT OF THE MACHINE CA.:270 T
MACHINE SIZE (LXWXH):14000X10000X9000 MM
CONTROL:SIEMENS 828D/SIEMENS 840D
:
:
:
WORKBENCH:
:
WORKTOOL SUPPORT (A-AXIS):2 STüCK
OPERATING MANUAL:
CONTROL CABINET SIEMENS PLC:
:
:
:1 STüCK
RAMS:1 STüCK KONVENTIONELLER UND 1 STüCK CNC-STößEL
CE-DESIGN:INKL. ZERTIFIKAT
:
EUROPEAN ELECTRIC:SCHNEIDER, SIEMENS, ABB ODER äHNLICH
4 JAW CHUCK:
SERVO MOTORS:VON SIEMENS
SPS MACHINE CONTROL:VON SIEMENS
LINEAR SCALES:
WORKPIECE MEASUREMENT SYSTEM:
C-AXIS:
CNC CONTROLS FROM:SIEMENS/FANUC/FAGOR
TURRET:
TOOL MEASURING SYSTEM:
SEMI GUARDING:

FOR MORE INFORMATION PLEASE CHECK ATTACHED PDF FILE ON THE RIGHT HAND SIDE
Vendedor: GK Werkzeugmaschinen GmbH
Año de construcción: usado
Precio: 1.759 €
Ubicación: Land-schneider electric integrated. servomotor-2.2 nm - 6000 rpm - o.bremse nominal auxiliary voltage [uh, nom] 250... 700 v continuous current at standstill 3 a continuous standstill torque 2,2 nm peak stillstand torque 8.7 nm rated power at the output of 720 w rated torque 1.15 nm nominal speed 6000 rpm max flow irms 12 amps nominal current [] smooth in] 1,5 a shaft end second wave without second shaft end shaft diameter 14 mm wavelength 30 mm width feather 20 mm type of feedback sincos absolute hiperface single turn resolution speed feedback 128 periods holding brake without mounting bracket international standard flange motor flange size 70 mm torque constant 0.76 nm/afor 120 â° c back-emf constant 49 v / krpmbei 20 â° c number of motor pole 6 SCHNEIDER ELECTRIC INTEGRATED. SERVOMOTOR-2.2 NM - 6000 RPM - O.BREMSE NOMINAL AUXILIARY VOLTAGE [UH, NOM] 250... 700 V CONTINUOUS CURRENT AT STANDSTILL 3 A CONTINUOUS STANDSTILL TORQUE 2,2 NM PEAK STILLSTAND TORQUE 8.7 NM RATED POWER AT THE OUTPUT OF 720 W RATED TORQUE 1.15 NM NOMINAL SPEED 6000 RPM MAX FLOW IRMS 12 AMPS NOMINAL CURRENT [] SMOOTH IN] 1,5 A SHAFT END SECOND WAVE WITHOUT SECOND SHAFT END SHAFT DIAMETER 14 MM WAVELENGTH 30 MM WIDTH FEATHER 20 MM TYPE OF FEEDBACK SINCOS ABSOLUTE HIPERFACE SINGLE TURN RESOLUTION SPEED FEEDBACK 128 PERIODS HOLDING BRAKE WITHOUT MOUNTING BRACKET INTERNATIONAL STANDARD FLANGE MOTOR FLANGE SIZE 70 MM TORQUE CONSTANT 0.76 NM/AFOR 120 &ACIRC;&DEG; C BACK-EMF CONSTANT 49 V / KRPMBEI 20 &ACIRC;&DEG; C NUMBER OF MOTOR POLE 6
Vendedor: KRASTEV EX-IMPORT
Año de construcción: usado
Ubicación: Land-x-travel:1500 mm<br/>y-travel:700 mm<br/>z-travel:500 mm<br/>:2000 x 500 mm mm<br/>max. table load:1800 kg<br/>t-slot (width-distance-quantity):5 x 18 x 80 mm<br/>spindle taper:50 iso<br/>turning speed range:(27 stufen) 30 - 2050 u/min<br/>distance spindle nose and table:25? 525 mm<br/>feeds:x/y/z: 0-1000 / 0-1000 / 0-500 mm/min<br/>rapid travel x/y/z:2200 / 2200 / 1100 mm/min<br/>power capacity:7,5 kw<br/>weight of the machine ca.:5 t<br/>machine dimensions lxwxh:2625 x 2260 x 2180 mm<br/>universal milling head:manuell schwenkbar, 360° <br/>dro:3-achsen <br/>central lubrication: <br/>halogen lamp: <br/>: <br/>european electric:im wesentlichen schneider <br/>: <br/>ce-design: <br/>: <br/>servo motors:in allen achsen <br/>screws cover: <br/>draw bar: <br/>machine tools: <br/>machine vice: <br/>round table, manual : <br/>milling and boring equipment: <br/><br/>100 % before loading  warranty: none  one used knee and column milling machine-universal, make union bielefeld, type usf 4, baujahr 1970, maschinen-nr. 55/214 X-TRAVEL:1500 MM
Y-TRAVEL:700 MM
Z-TRAVEL:500 MM
:2000 X 500 MM MM
MAX. TABLE LOAD:1800 KG
T-SLOT (WIDTH-DISTANCE-QUANTITY):5 X 18 X 80 MM
SPINDLE TAPER:50 ISO
TURNING SPEED RANGE:(27 STUFEN) 30 - 2050 U/MIN
DISTANCE SPINDLE NOSE AND TABLE:25? 525 MM
FEEDS:X/Y/Z: 0-1000 / 0-1000 / 0-500 MM/MIN
RAPID TRAVEL X/Y/Z:2200 / 2200 / 1100 MM/MIN
POWER CAPACITY:7,5 KW
WEIGHT OF THE MACHINE CA.:5 T
MACHINE DIMENSIONS LXWXH:2625 X 2260 X 2180 MM
UNIVERSAL MILLING HEAD:MANUELL SCHWENKBAR, 360°
DRO:3-ACHSEN
CENTRAL LUBRICATION:
HALOGEN LAMP:
:
EUROPEAN ELECTRIC:IM WESENTLICHEN SCHNEIDER
:
CE-DESIGN:
:
SERVO MOTORS:IN ALLEN ACHSEN
SCREWS COVER:
DRAW BAR:
MACHINE TOOLS:
MACHINE VICE:
ROUND TABLE, MANUAL :
MILLING AND BORING EQUIPMENT:

100 % BEFORE LOADING WARRANTY: NONE ONE USED KNEE AND COLUMN MILLING MACHINE-UNIVERSAL, MAKE UNION BIELEFELD, TYPE USF 4, BAUJAHR 1970, MASCHINEN-NR. 55/214
Vendedor: GK Werkzeugmaschinen GmbH
Año de construcción: usado
Precio: 1.759 €
Ubicación: Land-schneider electric integrated. servomotor-2.5 nm - 3000 rpm - multip.drehung - o.bremse ennhilfsspannung [uh, nom] 250... 700 v continuous current at standstill 1.8 a continuous standstill torque 2.5 nm peak stillstand torque 9.6 nm rated power at the output of 600 w nominal torque 1.9 nm nominal speed 3000 rpm max power irms 7.4 a rated current [in] 1.4 a shaft end smooth second shaft without second shaft end shaft diameter 19 mm wavelength 40 mm width feather 30 mm type of feedback absolutely sincos hiperface multi turn resolution speed feedback 128 periods without holding brake mounting bracket of international standard flange motor flange size 100 mm torque constant 1.39 nm/afor 120 â° c back-emf constant 90 v / krpmbei 20 â° c number of motor pole 8 SCHNEIDER ELECTRIC INTEGRATED. SERVOMOTOR-2.5 NM - 3000 RPM - MULTIP.DREHUNG - O.BREMSE ENNHILFSSPANNUNG [UH, NOM] 250... 700 V CONTINUOUS CURRENT AT STANDSTILL 1.8 A CONTINUOUS STANDSTILL TORQUE 2.5 NM PEAK STILLSTAND TORQUE 9.6 NM RATED POWER AT THE OUTPUT OF 600 W NOMINAL TORQUE 1.9 NM NOMINAL SPEED 3000 RPM MAX POWER IRMS 7.4 A RATED CURRENT [IN] 1.4 A SHAFT END SMOOTH SECOND SHAFT WITHOUT SECOND SHAFT END SHAFT DIAMETER 19 MM WAVELENGTH 40 MM WIDTH FEATHER 30 MM TYPE OF FEEDBACK ABSOLUTELY SINCOS HIPERFACE MULTI TURN RESOLUTION SPEED FEEDBACK 128 PERIODS WITHOUT HOLDING BRAKE MOUNTING BRACKET OF INTERNATIONAL STANDARD FLANGE MOTOR FLANGE SIZE 100 MM TORQUE CONSTANT 1.39 NM/AFOR 120 &ACIRC;&DEG; C BACK-EMF CONSTANT 90 V / KRPMBEI 20 &ACIRC;&DEG; C NUMBER OF MOTOR POLE 8
Vendedor: KRASTEV EX-IMPORT
Año de construcción: usado
Ubicación: Land-x-travel:600 mm<br/>y-travel:450 mm<br/>z-travel:450 mm<br/>spindle speeds:40-2000 1/min (vertikale spindel) / variabel <br/>spindle taper:40 iso<br/>spindle stroke:60 mm<br/>table surface area:850 x 450 mm (horiz.) <br/>table surface area:1190 x 250 mm (verti.) <br/>table load capacity:300 kg<br/>t-slot (width-distance-quantity):14  x 63 x 7 (für horiz. tisch) mm<br/>t-slot (width-distance-quantity):14  x 63 x 3 (für vert.tisch) mm<br/>feed:10-1000 mm/min<br/>feed stepless:in allen achsen <br/>rapid traverse  x + z axis:1200 mm/min<br/>:1200 mm/min.<br/>main drive:5,5 kw<br/>weight of the machine ca.:ca. 1750 kg<br/>dimensions of the machine ca.:ca. 1600 x 1800 x 2000 mm<br/>3-axis dro: <br/>reducing bush: <br/>: <br/>ce-design: <br/>coolant system: <br/>rear column: <br/>machine tools: <br/>: <br/>draw bar: <br/>european electric:im wesentlichen von schneider <br/>spindle protection:von techno piu (italien) <br/>servo motors: <br/>led work light: <br/><br/> X-TRAVEL:600 MM
Y-TRAVEL:450 MM
Z-TRAVEL:450 MM
SPINDLE SPEEDS:40-2000 1/MIN (VERTIKALE SPINDEL) / VARIABEL
SPINDLE TAPER:40 ISO
SPINDLE STROKE:60 MM
TABLE SURFACE AREA:850 X 450 MM (HORIZ.)
TABLE SURFACE AREA:1190 X 250 MM (VERTI.)
TABLE LOAD CAPACITY:300 KG
T-SLOT (WIDTH-DISTANCE-QUANTITY):14 X 63 X 7 (FüR HORIZ. TISCH) MM
T-SLOT (WIDTH-DISTANCE-QUANTITY):14 X 63 X 3 (FüR VERT.TISCH) MM
FEED:10-1000 MM/MIN
FEED STEPLESS:IN ALLEN ACHSEN
RAPID TRAVERSE X + Z AXIS:1200 MM/MIN
:1200 MM/MIN.
MAIN DRIVE:5,5 KW
WEIGHT OF THE MACHINE CA.:CA. 1750 KG
DIMENSIONS OF THE MACHINE CA.:CA. 1600 X 1800 X 2000 MM
3-AXIS DRO:
REDUCING BUSH:
:
CE-DESIGN:
COOLANT SYSTEM:
REAR COLUMN:
MACHINE TOOLS:
:
DRAW BAR:
EUROPEAN ELECTRIC:IM WESENTLICHEN VON SCHNEIDER
SPINDLE PROTECTION:VON TECHNO PIU (ITALIEN)
SERVO MOTORS:
LED WORK LIGHT:

Vendedor: GK Werkzeugmaschinen GmbH
Año de construcción: usado
Precio: 10.995 €
Ubicación: Land-schneider electric inverter atv950c13n4f 132kw, 400/440 series altivar process atv900 product or component type frequency inverters (ean 3606480884085) device application industry application short name of the appliance atv950 version with switch-disconnectors without brake chopper destination induction motors synchronous motors mounting variant bodenstehend emc filter integrated complies with iec/en 61800-3 category c3 protection class (ip) ip54 conforms to iec 61800-5-1 ip54 conforms to iec 60529 cooling type forced-air cooling mains frequency 50-60 hz (+/-5%) number of network phases 3 phases nominal auxiliary voltage [uh, nom] 380... 440 v (-15...10%) motor power (kw) 132 kw (standard overload) 110 kw (high overload) power 232 a for 400 v (standard overload) 197 (a) for 400 v (high overload) 250 a at 380 v (standard overload) 207 a at 380 v (high overload) short circuit power ik 50 ka apparent power 161 kva at 400 v () standard overload) 136 kva at 400 v (high overload) output rated current 250 a at 2.5 of khz (standard overload) 211 (a) 2.5 khz (high overload) maximum peak current 300 a during 60 s (standard overload) 317 a during 60 s (high overload) type motor control asynchronous motor constant variable torque optimized mode torque control profile for synchronous motors permanent magnet motor output frequency 0.1.. 599 hz of rated frequency of 2.5 of khz clock frequency 2... 8 khz adjustable 2, 5... 8 khz derating factor safety function sto (safe torque off (safe torque off) sil 3 logic input 16 preset speeds communication protocol of modbus ethernet/ip, serial modbus tcp) SCHNEIDER ELECTRIC INVERTER ATV950C13N4F 132KW, 400/440 SERIES ALTIVAR PROCESS ATV900 PRODUCT OR COMPONENT TYPE FREQUENCY INVERTERS (EAN 3606480884085) DEVICE APPLICATION INDUSTRY APPLICATION SHORT NAME OF THE APPLIANCE ATV950 VERSION WITH SWITCH-DISCONNECTORS WITHOUT BRAKE CHOPPER DESTINATION INDUCTION MOTORS SYNCHRONOUS MOTORS MOUNTING VARIANT BODENSTEHEND EMC FILTER INTEGRATED COMPLIES WITH IEC/EN 61800-3 CATEGORY C3 PROTECTION CLASS (IP) IP54 CONFORMS TO IEC 61800-5-1 IP54 CONFORMS TO IEC 60529 COOLING TYPE FORCED-AIR COOLING MAINS FREQUENCY 50-60 HZ (+/-5%) NUMBER OF NETWORK PHASES 3 PHASES NOMINAL AUXILIARY VOLTAGE [UH, NOM] 380... 440 V (-15...10%) MOTOR POWER (KW) 132 KW (STANDARD OVERLOAD) 110 KW (HIGH OVERLOAD) POWER 232 A FOR 400 V (STANDARD OVERLOAD) 197 (A) FOR 400 V (HIGH OVERLOAD) 250 A AT 380 V (STANDARD OVERLOAD) 207 A AT 380 V (HIGH OVERLOAD) SHORT CIRCUIT POWER IK 50 KA APPARENT POWER 161 KVA AT 400 V () STANDARD OVERLOAD) 136 KVA AT 400 V (HIGH OVERLOAD) OUTPUT RATED CURRENT 250 A AT 2.5 OF KHZ (STANDARD OVERLOAD) 211 (A) 2.5 KHZ (HIGH OVERLOAD) MAXIMUM PEAK CURRENT 300 A DURING 60 S (STANDARD OVERLOAD) 317 A DURING 60 S (HIGH OVERLOAD) TYPE MOTOR CONTROL ASYNCHRONOUS MOTOR CONSTANT VARIABLE TORQUE OPTIMIZED MODE TORQUE CONTROL PROFILE FOR SYNCHRONOUS MOTORS PERMANENT MAGNET MOTOR OUTPUT FREQUENCY 0.1.. 599 HZ OF RATED FREQUENCY OF 2.5 OF KHZ CLOCK FREQUENCY 2... 8 KHZ ADJUSTABLE 2, 5... 8 KHZ DERATING FACTOR SAFETY FUNCTION STO (SAFE TORQUE OFF (SAFE TORQUE OFF) SIL 3 LOGIC INPUT 16 PRESET SPEEDS COMMUNICATION PROTOCOL OF MODBUS ETHERNET/IP, SERIAL MODBUS TCP)
Vendedor: KRASTEV EX-IMPORT
Año de construcción: usado
Ubicación: Land-faceplate diameter:10000 mm<br/>swing diameter:10000 mm<br/>turning height:5000 mm<br/>ram head dimension:280x280 mm<br/>workpiece weight:200 t<br/>table turning speeds:0.23 ? 14 u/min<br/>transmission ratio:2 stück<br/>travel of ram (vertical):2500 mm<br/>travel of ram (horiz.):5150 mm<br/>machine size (lxwxh):ca. 19500x11500×11600 mm<br/>main drive:132 kw<br/>weight of the machine ca.:290 t<br/>cnc controller:siemens 828d/fanuc 0i tf <br/>hydr. components:kompass (taiwan) <br/>rams:2 (konv. + cnc) stk.<br/>electrics from schneider or siemens: <br/>servo spindle motor:siemens/fanuc <br/>ce-design:optional <br/><br/>stock machine with short delivery time of only approx. 3-4 months. main components available!  brand new vertical lathes double stand, type kraft, type vtl - 100 cnc incl. siemens 828d or fanuc 0i tf with two tappets (one piece of conventional and one piece cnc controlled ram)  substantially parts of the hydraulics of taiwanese manufacturer compass  illustration similar. also leasing and hire purchase possible! further information can be found in the attachment. all components can be replaced by other components from reputable manufacturers. other components can also be changed at short notice according to customer specifications. the cnc control from siemens is adapted and optimized by german experts.  new: including 12 months free multimedia data glasses for remote online service and remote maintenance kit for the cnc control! so that you can be helped quickly and effectively! FACEPLATE DIAMETER:10000 MM
SWING DIAMETER:10000 MM
TURNING HEIGHT:5000 MM
RAM HEAD DIMENSION:280X280 MM
WORKPIECE WEIGHT:200 T
TABLE TURNING SPEEDS:0.23 ? 14 U/MIN
TRANSMISSION RATIO:2 STüCK
TRAVEL OF RAM (VERTICAL):2500 MM
TRAVEL OF RAM (HORIZ.):5150 MM
MACHINE SIZE (LXWXH):CA. 19500X11500×11600 MM
MAIN DRIVE:132 KW
WEIGHT OF THE MACHINE CA.:290 T
CNC CONTROLLER:SIEMENS 828D/FANUC 0I TF
HYDR. COMPONENTS:KOMPASS (TAIWAN)
RAMS:2 (KONV. + CNC) STK.
ELECTRICS FROM SCHNEIDER OR SIEMENS:
SERVO SPINDLE MOTOR:SIEMENS/FANUC
CE-DESIGN:OPTIONAL

STOCK MACHINE WITH SHORT DELIVERY TIME OF ONLY APPROX. 3-4 MONTHS. MAIN COMPONENTS AVAILABLE! BRAND NEW VERTICAL LATHES DOUBLE STAND, TYPE KRAFT, TYPE VTL - 100 CNC INCL. SIEMENS 828D OR FANUC 0I TF WITH TWO TAPPETS (ONE PIECE OF CONVENTIONAL AND ONE PIECE CNC CONTROLLED RAM) SUBSTANTIALLY PARTS OF THE HYDRAULICS OF TAIWANESE MANUFACTURER COMPASS ILLUSTRATION SIMILAR. ALSO LEASING AND HIRE PURCHASE POSSIBLE! FURTHER INFORMATION CAN BE FOUND IN THE ATTACHMENT. ALL COMPONENTS CAN BE REPLACED BY OTHER COMPONENTS FROM REPUTABLE MANUFACTURERS. OTHER COMPONENTS CAN ALSO BE CHANGED AT SHORT NOTICE ACCORDING TO CUSTOMER SPECIFICATIONS. THE CNC CONTROL FROM SIEMENS IS ADAPTED AND OPTIMIZED BY GERMAN EXPERTS. NEW: INCLUDING 12 MONTHS FREE MULTIMEDIA DATA GLASSES FOR REMOTE ONLINE SERVICE AND REMOTE MAINTENANCE KIT FOR THE CNC CONTROL! SO THAT YOU CAN BE HELPED QUICKLY AND EFFECTIVELY!
Vendedor: GK Werkzeugmaschinen GmbH
Año de construcción: usado
Precio: 29.900 €
Ubicación: Land-schneider electric inverter, atv960c40q4x1, in the control cabinet, 400kw, 400v-ip21 altivar series process atv900, rodukt or component type inverter device application industry application short name of the appliance atv960 destination product induction motors synchronous motors construction floor cabinet, compact design supplied equipment housing for spacial sf graphic control unit in the housing door inverter main switch mains choke for main supply terminal strip terminal strip for motor you/dt-filter choke cable bottom color of the panel light grey ral 7035 protection degree (ip) ip23 complies with iec 61800-5-1 cooling type forced-air cooling nominal auxiliary voltage [uh, nom] 380... 415 v (-10...6%) mains frequency 50/60 hz (+/-5%) number of phases of power 3-phase overvoltage category iii type motor control asynchronous motor constant variable torque optimized mode of torque control profile for synchronous motors permanent magnet motor output voltage &lt; = supply voltage permissible temporary current gain 1.2 x in for 60 s (standard overload) 1.5 x in for 60 s (high overload) rated clock frequency of 2.5 of khz clock frequency 2... 8 khz adjustable with derating factor output frequency 0.1.. 500 hz motor power (kw) 400 kw (standard overload) 315 kw (high overload) output rated current 730 a at 2.5 of khz (standard overload) 590 a at 2.5 khz (high overload) ac 681 a isc = 50 for 400 v (normal duty) 545 a isc ka 50 ka at 400 v (heavy duty) apparent power kva = 472 kva at 400 v (standard overload) 378  at 400 v (high overload) thdi &lt; = 43% upstream full load according to iec 61000-3-12 short circuit protection: 800 a gg upstream fuse (standard overload): 630 a gg backup (high overload) internal: 315 a 3 ar backup energy efficiency &gt; = 0.98 w dissipated 9900 w total () normal duty) 7370 w total (heavy duty) 1120 w control part (normal duty) 770 w (high overload) cooling air volume control part 280 m3/h for control 1740 m3/h for output noise level 71 db 86/188/eec - physical agents (noise) directive network short-circuit current 50 ka for 100 ms electrical connection control: _test removable screw terminals 0, 5...1, 5 mmâ² main voltage supply: _test rail m12 engine: _test rail m12 recommended cable cross section motor 3 x (3 x 120 mm 2) (high overload) 3 x (3 x 185 mm â²) (standard overload) 4 x (3 x 120 mmâ²) () standard overload) 4 x (3 x 95 mm 2) (high overload) cable construction 4 x (3 x 150 mm 2) (default overload) 3 x (3 x 150 mm 2) (high overload) 4 x (3 x 95 mm 2) (high overload) width 800 mm height 2150 mm length 664 mm product weight 650 kg logic input 16 preset speeds kommunikationspro ethernet/ip protocol, modbus, serial modbus tcp SCHNEIDER ELECTRIC INVERTER, ATV960C40Q4X1, IN THE CONTROL CABINET, 400KW, 400V-IP21 ALTIVAR SERIES PROCESS ATV900, RODUKT OR COMPONENT TYPE INVERTER DEVICE APPLICATION INDUSTRY APPLICATION SHORT NAME OF THE APPLIANCE ATV960 DESTINATION PRODUCT INDUCTION MOTORS SYNCHRONOUS MOTORS CONSTRUCTION FLOOR CABINET, COMPACT DESIGN SUPPLIED EQUIPMENT HOUSING FOR SPACIAL SF GRAPHIC CONTROL UNIT IN THE HOUSING DOOR INVERTER MAIN SWITCH MAINS CHOKE FOR MAIN SUPPLY TERMINAL STRIP TERMINAL STRIP FOR MOTOR YOU/DT-FILTER CHOKE CABLE BOTTOM COLOR OF THE PANEL LIGHT GREY RAL 7035 PROTECTION DEGREE (IP) IP23 COMPLIES WITH IEC 61800-5-1 COOLING TYPE FORCED-AIR COOLING NOMINAL AUXILIARY VOLTAGE [UH, NOM] 380... 415 V (-10...6%) MAINS FREQUENCY 50/60 HZ (+/-5%) NUMBER OF PHASES OF POWER 3-PHASE OVERVOLTAGE CATEGORY III TYPE MOTOR CONTROL ASYNCHRONOUS MOTOR CONSTANT VARIABLE TORQUE OPTIMIZED MODE OF TORQUE CONTROL PROFILE FOR SYNCHRONOUS MOTORS PERMANENT MAGNET MOTOR OUTPUT VOLTAGE &LT; = SUPPLY VOLTAGE PERMISSIBLE TEMPORARY CURRENT GAIN 1.2 X IN FOR 60 S (STANDARD OVERLOAD) 1.5 X IN FOR 60 S (HIGH OVERLOAD) RATED CLOCK FREQUENCY OF 2.5 OF KHZ CLOCK FREQUENCY 2... 8 KHZ ADJUSTABLE WITH DERATING FACTOR OUTPUT FREQUENCY 0.1.. 500 HZ MOTOR POWER (KW) 400 KW (STANDARD OVERLOAD) 315 KW (HIGH OVERLOAD) OUTPUT RATED CURRENT 730 A AT 2.5 OF KHZ (STANDARD OVERLOAD) 590 A AT 2.5 KHZ (HIGH OVERLOAD) AC 681 A ISC = 50 FOR 400 V (NORMAL DUTY) 545 A ISC KA 50 KA AT 400 V (HEAVY DUTY) APPARENT POWER KVA = 472 KVA AT 400 V (STANDARD OVERLOAD) 378 AT 400 V (HIGH OVERLOAD) THDI &LT; = 43% UPSTREAM FULL LOAD ACCORDING TO IEC 61000-3-12 SHORT CIRCUIT PROTECTION: 800 A GG UPSTREAM FUSE (STANDARD OVERLOAD): 630 A GG BACKUP (HIGH OVERLOAD) INTERNAL: 315 A 3 AR BACKUP ENERGY EFFICIENCY &GT; = 0.98 W DISSIPATED 9900 W TOTAL () NORMAL DUTY) 7370 W TOTAL (HEAVY DUTY) 1120 W CONTROL PART (NORMAL DUTY) 770 W (HIGH OVERLOAD) COOLING AIR VOLUME CONTROL PART 280 M3/H FOR CONTROL 1740 M3/H FOR OUTPUT NOISE LEVEL 71 DB 86/188/EEC - PHYSICAL AGENTS (NOISE) DIRECTIVE NETWORK SHORT-CIRCUIT CURRENT 50 KA FOR 100 MS ELECTRICAL CONNECTION CONTROL: _TEST REMOVABLE SCREW TERMINALS 0, 5...1, 5 MM&ACIRC;&SUP2; MAIN VOLTAGE SUPPLY: _TEST RAIL M12 ENGINE: _TEST RAIL M12 RECOMMENDED CABLE CROSS SECTION MOTOR 3 X (3 X 120 MM 2) (HIGH OVERLOAD) 3 X (3 X 185 MM &ACIRC;&SUP2;) (STANDARD OVERLOAD) 4 X (3 X 120 MM&ACIRC;&SUP2;) () STANDARD OVERLOAD) 4 X (3 X 95 MM 2) (HIGH OVERLOAD) CABLE CONSTRUCTION 4 X (3 X 150 MM 2) (DEFAULT OVERLOAD) 3 X (3 X 150 MM 2) (HIGH OVERLOAD) 4 X (3 X 95 MM 2) (HIGH OVERLOAD) WIDTH 800 MM HEIGHT 2150 MM LENGTH 664 MM PRODUCT WEIGHT 650 KG LOGIC INPUT 16 PRESET SPEEDS KOMMUNIKATIONSPRO ETHERNET/IP PROTOCOL, MODBUS, SERIAL MODBUS TCP
Vendedor: KRASTEV EX-IMPORT
Año de construcción: usado
Ubicación: Land-faceplate diameter:6300 mm<br/>swing diameter:8000 mm<br/>turning height:4000 mm<br/>workpiece weight:120 t<br/>table speeds:0.2-16 u/min (2 stufen) <br/>max. torque on the faceplate:200/460  k.nm<br/>slide stroke:vertikal: 2500 mm<br/>slide stroke:horizontal: 4350 mm<br/>cross section of ram:280x280 mm<br/>max. cutting force of tool head :links: 63 kn / rechts: 80 kn <br/>cross rail travel :2000 mm<br/>rapid feed cross beam:300 mm/min<br/>feed stepless:x-achse: 1-500 mm/min<br/>main drive:110 kw<br/>weight of the machine ca.:190 t<br/>machine size (lxwxh):11000x9000x8000 mm<br/>control:siemens 828d/siemens 840d <br/>: <br/>: <br/>: <br/>workbench: <br/>: <br/>worktool support (a-axis):2 stück<br/>operating manual: <br/>control cabinet siemens plc: <br/>: <br/>: <br/>:1 stück<br/>rams:1 stück konventioneller und 1 stück cnc-stößel <br/>ce-design:inkl. zertifikat <br/>: <br/>european electric:schneider, siemens, abb oder ähnlich <br/>4 jaw chuck: <br/>servo motors:von siemens <br/>sps machine control:von siemens <br/>linear scales: <br/>workpiece measurement system: <br/>c-axis: <br/>cnc controls from:siemens/fanuc/fagor <br/>turret: <br/>tool measuring system: <br/>semi guarding: <br/><br/>for more information please check attached pdf file on the right hand side FACEPLATE DIAMETER:6300 MM
SWING DIAMETER:8000 MM
TURNING HEIGHT:4000 MM
WORKPIECE WEIGHT:120 T
TABLE SPEEDS:0.2-16 U/MIN (2 STUFEN)
MAX. TORQUE ON THE FACEPLATE:200/460 K.NM
SLIDE STROKE:VERTIKAL: 2500 MM
SLIDE STROKE:HORIZONTAL: 4350 MM
CROSS SECTION OF RAM:280X280 MM
MAX. CUTTING FORCE OF TOOL HEAD :LINKS: 63 KN / RECHTS: 80 KN
CROSS RAIL TRAVEL :2000 MM
RAPID FEED CROSS BEAM:300 MM/MIN
FEED STEPLESS:X-ACHSE: 1-500 MM/MIN
MAIN DRIVE:110 KW
WEIGHT OF THE MACHINE CA.:190 T
MACHINE SIZE (LXWXH):11000X9000X8000 MM
CONTROL:SIEMENS 828D/SIEMENS 840D
:
:
:
WORKBENCH:
:
WORKTOOL SUPPORT (A-AXIS):2 STüCK
OPERATING MANUAL:
CONTROL CABINET SIEMENS PLC:
:
:
:1 STüCK
RAMS:1 STüCK KONVENTIONELLER UND 1 STüCK CNC-STößEL
CE-DESIGN:INKL. ZERTIFIKAT
:
EUROPEAN ELECTRIC:SCHNEIDER, SIEMENS, ABB ODER äHNLICH
4 JAW CHUCK:
SERVO MOTORS:VON SIEMENS
SPS MACHINE CONTROL:VON SIEMENS
LINEAR SCALES:
WORKPIECE MEASUREMENT SYSTEM:
C-AXIS:
CNC CONTROLS FROM:SIEMENS/FANUC/FAGOR
TURRET:
TOOL MEASURING SYSTEM:
SEMI GUARDING:

FOR MORE INFORMATION PLEASE CHECK ATTACHED PDF FILE ON THE RIGHT HAND SIDE
Vendedor: GK Werkzeugmaschinen GmbH
Año de construcción: usado
Ubicación: Land-many thanks for your interest on our second hand machines, please find follow our offer:
manufacturer:	utzschneider
type:			schokoladentank / chocolate tank
volume		ca. 4000kg – 6000liter
electrical:		400v
dimensions:		höhe ohne motor ca. 2400 mm / high without engine
space requirement:	ca. durchmesser 2300 mm

different:		engine dismantled for transport, double jacked for heating with steam or water 

we offer this machine in as-is where-is condition 
 MANY THANKS FOR YOUR INTEREST ON OUR SECOND HAND MACHINES, PLEASE FIND FOLLOW OUR OFFER: MANUFACTURER: UTZSCHNEIDER TYPE: SCHOKOLADENTANK / CHOCOLATE TANK VOLUME CA. 4000KG – 6000LITER ELECTRICAL: 400V DIMENSIONS: HöHE OHNE MOTOR CA. 2400 MM / HIGH WITHOUT ENGINE SPACE REQUIREMENT: CA. DURCHMESSER 2300 MM DIFFERENT: ENGINE DISMANTLED FOR TRANSPORT, DOUBLE JACKED FOR HEATING WITH STEAM OR WATER WE OFFER THIS MACHINE IN AS-IS WHERE-IS CONDITION
Vendedor: Peter Heidenreich Maschinenhandel
Año de construcción: usado
Precio: 7.040 €
Ubicación: Land-: 2.500 kg<br/>: 50 - 400 mm<br/>motorized drive<br/>mechanical adjustable coil mandrel with 4 jaws<br/>schneider speed control for decoiling speed aswell as acceleration- and deceleration times<br/>photoelectric proximity ensor sick for sag control <br/><br/><br/>non motorized with pneumatic brake - price on request<br/>pneumatic hold down arm - price on request<br/><br/>double-head decoilers, as well as horizontal pallet decoilers on request<br/><br/>because the application areas are always very specific for each customer and require intense counseling, we kindly ask for your inquiry in order to make you an individual offer!<br/><br/>(sample photos)<br/><br/><br/><br/><br/><br/><br/><br/>max. coil weight: 2.500 kg<br/>coil width: 50 - 400 mm<br/><br/><br/><br/> : 2.500 KG
: 50 - 400 MM
MOTORIZED DRIVE
MECHANICAL ADJUSTABLE COIL MANDREL WITH 4 JAWS
SCHNEIDER SPEED CONTROL FOR DECOILING SPEED ASWELL AS ACCELERATION- AND DECELERATION TIMES
PHOTOELECTRIC PROXIMITY ENSOR SICK FOR SAG CONTROL


NON MOTORIZED WITH PNEUMATIC BRAKE - PRICE ON REQUEST
PNEUMATIC HOLD DOWN ARM - PRICE ON REQUEST

DOUBLE-HEAD DECOILERS, AS WELL AS HORIZONTAL PALLET DECOILERS ON REQUEST

BECAUSE THE APPLICATION AREAS ARE ALWAYS VERY SPECIFIC FOR EACH CUSTOMER AND REQUIRE INTENSE COUNSELING, WE KINDLY ASK FOR YOUR INQUIRY IN ORDER TO MAKE YOU AN INDIVIDUAL OFFER!

(SAMPLE PHOTOS)







MAX. COIL WEIGHT: 2.500 KG
COIL WIDTH: 50 - 400 MM



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land-complete line, very good condition, for the crushing of wood chips, consisting of:
1- conveyor belt for wooden chips, width 50 cm, length 750 cm, drive 2.2 kw;
2- hammer mill monstra skc1300/625-50, drive 110 kw, new screen for granulation 12 mm;
3- electrical cabinet, soft starter, components schneider electric;
4- l-conveyor belt for sawdust, width 60 cm, length 900 cm, drive 2.2 kw;
5- hammermill refiner, drive 75 kw, new screen for granulation 5 mm;
6- large mixer/conditioner for sawdust;
7- 2 screw transporters and 2 mixers.  COMPLETE LINE, VERY GOOD CONDITION, FOR THE CRUSHING OF WOOD CHIPS, CONSISTING OF: 1- CONVEYOR BELT FOR WOODEN CHIPS, WIDTH 50 CM, LENGTH 750 CM, DRIVE 2.2 KW; 2- HAMMER MILL MONSTRA SKC1300/625-50, DRIVE 110 KW, NEW SCREEN FOR GRANULATION 12 MM; 3- ELECTRICAL CABINET, SOFT STARTER, COMPONENTS SCHNEIDER ELECTRIC; 4- L-CONVEYOR BELT FOR SAWDUST, WIDTH 60 CM, LENGTH 900 CM, DRIVE 2.2 KW; 5- HAMMERMILL REFINER, DRIVE 75 KW, NEW SCREEN FOR GRANULATION 5 MM; 6- LARGE MIXER/CONDITIONER FOR SAWDUST; 7- 2 SCREW TRANSPORTERS AND 2 MIXERS.
Vendedor: SEEnergy Timber doo
Año de construcción: usado
Precio: 3.290 €
Ubicación: Land-: 500 kg<br/>: 50 - 300 mm<br/>motorized drive<br/>mechanical adjustable coil mandrel with 4 jaws<br/>schneider speed control for decoiling speed aswell as acceleration- and deceleration times<br/>photoelectric proximity ensor sick for sag control <br/><br/><br/>non motorized with pneumatic brake - price on request<br/>pneumatic hold down arm - price on request<br/><br/>double-head decoilers, as well as horizontal pallet decoilers on request<br/><br/>because the application areas are always very specific for each customer and require intense counseling, we kindly ask for your inquiry in order to make you an individual offer!<br/><br/>(sample photos)<br/><br/><br/><br/><br/><br/><br/><br/>max. coil weight: 500 kg<br/>coil width: 50 - 300 mm<br/><br/><br/><br/> : 500 KG
: 50 - 300 MM
MOTORIZED DRIVE
MECHANICAL ADJUSTABLE COIL MANDREL WITH 4 JAWS
SCHNEIDER SPEED CONTROL FOR DECOILING SPEED ASWELL AS ACCELERATION- AND DECELERATION TIMES
PHOTOELECTRIC PROXIMITY ENSOR SICK FOR SAG CONTROL


NON MOTORIZED WITH PNEUMATIC BRAKE - PRICE ON REQUEST
PNEUMATIC HOLD DOWN ARM - PRICE ON REQUEST

DOUBLE-HEAD DECOILERS, AS WELL AS HORIZONTAL PALLET DECOILERS ON REQUEST

BECAUSE THE APPLICATION AREAS ARE ALWAYS VERY SPECIFIC FOR EACH CUSTOMER AND REQUIRE INTENSE COUNSELING, WE KINDLY ASK FOR YOUR INQUIRY IN ORDER TO MAKE YOU AN INDIVIDUAL OFFER!

(SAMPLE PHOTOS)







MAX. COIL WEIGHT: 500 KG
COIL WIDTH: 50 - 300 MM



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Precio: 43.500 €
Ubicación: Land-manufacturer: cnc hydraulic press brake
 type: cnc hap 225/30/25
 condition: new
 warranty: 2 years

maximum print performance 225 tons
 bcb9d8quo7
 max sheet width 3000 mm
 cybelec cybtouch 12 2d graphical control 3 axes + r-axis (y1, y2, x) inanlar lower (110,80,50,35)eurostamp 1260 oberwekzeug small tischmonoblock konstruktionpromecam o tool schnellklemmsystemcnc steel welding controlled motorized backgauge (x: 750 mm) adjustable rear fence fingerinch and metric systemgeschliffene and chrome-plated zylinderklappbarer bedienpultfusbedienung guard (secured with limit switch) photocell with anti-panic stopseitliche (cat. 04) rear guard rexroth hydraulic system rexroth hydraulic pumpevordere auflegeã¤rme electronic unit by: schneider380 v 50 hz electricitymanuel bombierungbedienungsanleitung & training in german start-up

light curtain on backside 900 mm
 servo of motor mitsubishi backgauge
 r axis
 dsp laser finger protection
 MANUFACTURER: CNC HYDRAULIC PRESS BRAKE TYPE: CNC HAP 225/30/25 CONDITION: NEW WARRANTY: 2 YEARS MAXIMUM PRINT PERFORMANCE 225 TONS BCB9D8QUO7 MAX SHEET WIDTH 3000 MM CYBELEC CYBTOUCH 12 2D GRAPHICAL CONTROL 3 AXES + R-AXIS (Y1, Y2, X) INANLAR LOWER (110,80,50,35)EUROSTAMP 1260 OBERWEKZEUG SMALL TISCHMONOBLOCK KONSTRUKTIONPROMECAM O TOOL SCHNELLKLEMMSYSTEMCNC STEEL WELDING CONTROLLED MOTORIZED BACKGAUGE (X: 750 MM) ADJUSTABLE REAR FENCE FINGERINCH AND METRIC SYSTEMGESCHLIFFENE AND CHROME-PLATED ZYLINDERKLAPPBARER BEDIENPULTFUSBEDIENUNG GUARD (SECURED WITH LIMIT SWITCH) PHOTOCELL WITH ANTI-PANIC STOPSEITLICHE (CAT. 04) REAR GUARD REXROTH HYDRAULIC SYSTEM REXROTH HYDRAULIC PUMPEVORDERE AUFLEGE&ATILDE;&CURREN;RME ELECTRONIC UNIT BY: SCHNEIDER380 V 50 HZ ELECTRICITYMANUEL BOMBIERUNGBEDIENUNGSANLEITUNG & TRAINING IN GERMAN START-UP LIGHT CURTAIN ON BACKSIDE 900 MM SERVO OF MOTOR MITSUBISHI BACKGAUGE R AXIS DSP LASER FINGER PROTECTION
Vendedor: RM-Industrieservice Lager und Büro
Año de construcción: usado
Precio: 16.090 €
Ubicación: Land-: 600 mm<br/>: 3 mm<br/>: 600 x 2 mm<br/>: 80 mm<br/>: 10 nm<br/>helical gear box wattdrive (made in austria)<br/>festo pneumatic equipment<br/>servo drive and control schneider electric<br/>7", colour touchscreen schneider electric<br/>4 gear rollers drive. prevents the separation of the rollers during piloting operation for higher accuracy<br/>free feeding speed 100mt/min<br/><br/>because the application areas are always very specific for each customer and require intense counseling, we kindly ask for your inquiry in order to make you an individual offer!<br/><br/>(sample photo)<br/><br/><br/><br/><br/><br/><br/><br/>sheet width: 600 mm<br/>min. sheet thickness: 0,4 mm<br/>max. sheet thickness: 3 mm<br/>max. section: 600 x 2 mm<br/>roll Ø: 80 mm<br/>motor torque: 10 nm<br/><br/><br/><br/> : 600 MM
: 3 MM
: 600 X 2 MM
: 80 MM
: 10 NM
HELICAL GEAR BOX WATTDRIVE (MADE IN AUSTRIA)
FESTO PNEUMATIC EQUIPMENT
SERVO DRIVE AND CONTROL SCHNEIDER ELECTRIC
7", COLOUR TOUCHSCREEN SCHNEIDER ELECTRIC
4 GEAR ROLLERS DRIVE. PREVENTS THE SEPARATION OF THE ROLLERS DURING PILOTING OPERATION FOR HIGHER ACCURACY
FREE FEEDING SPEED 100MT/MIN

BECAUSE THE APPLICATION AREAS ARE ALWAYS VERY SPECIFIC FOR EACH CUSTOMER AND REQUIRE INTENSE COUNSELING, WE KINDLY ASK FOR YOUR INQUIRY IN ORDER TO MAKE YOU AN INDIVIDUAL OFFER!

(SAMPLE PHOTO)







SHEET WIDTH: 600 MM
MIN. SHEET THICKNESS: 0,4 MM
MAX. SHEET THICKNESS: 3 MM
MAX. SECTION: 600 X 2 MM
ROLL Ø: 80 MM
MOTOR TORQUE: 10 NM



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land-made in italy machine according to din 8605: lathe with increased accuracy.

tip height: 215 mm
turning diameter over bed: 430 mm
swing over carriage: 240 mm
top width: 1,000 mm
bed width: 290 mm
spindle bore: 52 mm
spindle nose: camlock 6 "
spindle speeds variable: 6
spindle speeds: 60-2,000 rpm
s6/s1 engine power: 4 kw (option: 5.5 kw) feed z-axis: (38) 0.05 - 1.88 mm / rev
feed x axis: (38) 0.02 1,084 mm / rev
thread cutting, metric: (30) 0.45-20 mm
thread cutting, witworth: (35) 80-1 3/4 tpi
thread cutting, module: (25) 0.25-10 mm
thread cutting, diametral pitch: (30) 160-3 1/2 d.p..
cross slide lxw: 370 x 190 mm
transversal carriage stroke: 240 mm
upper carriage lxw: 275 x 115 mm
upper carriage stroke: 120 mm
tailstock quill diameter: 60 mm
tailstock quill stroke: 135 mm
tailstock taper: mk 4
weight: approx. 2,000 kg

facilities:
-infinitely variable spindle speed with digital speed display
-automatic lubrication of guideways
-acceptance protocol according to din 8605, lathe with high accuracy
-electrical equipment of high quality brand components, siemens/schneider
-reducing bushing
-2 fixed centres
-all safety devices according to ce standards: rotary chuck guard secured with plexiglas window, limit microswitch. chisel holder protection with plexiglass. rear splash guard along the entire length. lead screw and train spindle protection by photoelectric sensor (included in the emergency stop circuit). emergency off pushbutton.
-shaving container with wheels
-coolant system
-fixed bezel
-revolving bezel
-control tool, acceptance protocol according to din, operating and maintenance manuals, complete electrical installation, machine manufactured according to ce standard in the latest version. MADE IN ITALY MACHINE ACCORDING TO DIN 8605: LATHE WITH INCREASED ACCURACY. TIP HEIGHT: 215 MM TURNING DIAMETER OVER BED: 430 MM SWING OVER CARRIAGE: 240 MM TOP WIDTH: 1,000 MM BED WIDTH: 290 MM SPINDLE BORE: 52 MM SPINDLE NOSE: CAMLOCK 6 " SPINDLE SPEEDS VARIABLE: 6 SPINDLE SPEEDS: 60-2,000 RPM S6/S1 ENGINE POWER: 4 KW (OPTION: 5.5 KW) FEED Z-AXIS: (38) 0.05 - 1.88 MM / REV FEED X AXIS: (38) 0.02 1,084 MM / REV THREAD CUTTING, METRIC: (30) 0.45-20 MM THREAD CUTTING, WITWORTH: (35) 80-1 3/4 TPI THREAD CUTTING, MODULE: (25) 0.25-10 MM THREAD CUTTING, DIAMETRAL PITCH: (30) 160-3 1/2 D.P.. CROSS SLIDE LXW: 370 X 190 MM TRANSVERSAL CARRIAGE STROKE: 240 MM UPPER CARRIAGE LXW: 275 X 115 MM UPPER CARRIAGE STROKE: 120 MM TAILSTOCK QUILL DIAMETER: 60 MM TAILSTOCK QUILL STROKE: 135 MM TAILSTOCK TAPER: MK 4 WEIGHT: APPROX. 2,000 KG FACILITIES: -INFINITELY VARIABLE SPINDLE SPEED WITH DIGITAL SPEED DISPLAY -AUTOMATIC LUBRICATION OF GUIDEWAYS -ACCEPTANCE PROTOCOL ACCORDING TO DIN 8605, LATHE WITH HIGH ACCURACY -ELECTRICAL EQUIPMENT OF HIGH QUALITY BRAND COMPONENTS, SIEMENS/SCHNEIDER -REDUCING BUSHING -2 FIXED CENTRES -ALL SAFETY DEVICES ACCORDING TO CE STANDARDS: ROTARY CHUCK GUARD SECURED WITH PLEXIGLAS WINDOW, LIMIT MICROSWITCH. CHISEL HOLDER PROTECTION WITH PLEXIGLASS. REAR SPLASH GUARD ALONG THE ENTIRE LENGTH. LEAD SCREW AND TRAIN SPINDLE PROTECTION BY PHOTOELECTRIC SENSOR (INCLUDED IN THE EMERGENCY STOP CIRCUIT). EMERGENCY OFF PUSHBUTTON. -SHAVING CONTAINER WITH WHEELS -COOLANT SYSTEM -FIXED BEZEL -REVOLVING BEZEL -CONTROL TOOL, ACCEPTANCE PROTOCOL ACCORDING TO DIN, OPERATING AND MAINTENANCE MANUALS, COMPLETE ELECTRICAL INSTALLATION, MACHINE MANUFACTURED ACCORDING TO CE STANDARD IN THE LATEST VERSION.
Vendedor: Weber Werkzeugmaschinen GbR
Año de construcción: usado
Precio: 7.890 €
Ubicación: Land-: 2.500 kg<br/>: 50 - 600 mm<br/>motorized drive<br/>mechanical adjustable coil mandrel with 4 jaws<br/>schneider speed control for decoiling speed aswell as acceleration- and deceleration times<br/>photoelectric proximity ensor sick for sag control <br/><br/><br/>non motorized with pneumatic brake - price on request<br/>pneumatic hold down arm - price on request<br/><br/>double-head decoilers, as well as horizontal pallet decoilers on request<br/><br/>because the application areas are always very specific for each customer and require intense counseling, we kindly ask for your inquiry in order to make you an individual offer!<br/><br/>(sample photos)<br/><br/><br/><br/><br/><br/><br/><br/>max. coil weight: 2.500 kg<br/>coil width: 50 - 600 mm<br/><br/><br/><br/> : 2.500 KG
: 50 - 600 MM
MOTORIZED DRIVE
MECHANICAL ADJUSTABLE COIL MANDREL WITH 4 JAWS
SCHNEIDER SPEED CONTROL FOR DECOILING SPEED ASWELL AS ACCELERATION- AND DECELERATION TIMES
PHOTOELECTRIC PROXIMITY ENSOR SICK FOR SAG CONTROL


NON MOTORIZED WITH PNEUMATIC BRAKE - PRICE ON REQUEST
PNEUMATIC HOLD DOWN ARM - PRICE ON REQUEST

DOUBLE-HEAD DECOILERS, AS WELL AS HORIZONTAL PALLET DECOILERS ON REQUEST

BECAUSE THE APPLICATION AREAS ARE ALWAYS VERY SPECIFIC FOR EACH CUSTOMER AND REQUIRE INTENSE COUNSELING, WE KINDLY ASK FOR YOUR INQUIRY IN ORDER TO MAKE YOU AN INDIVIDUAL OFFER!

(SAMPLE PHOTOS)







MAX. COIL WEIGHT: 2.500 KG
COIL WIDTH: 50 - 600 MM



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land-made in italy machine according to din 8606

tip height: 260 mm
turning diameter over bed: 520 mm
swing over carriage: 300 mm
centre distance: 1500 mm
bed width: 400 mm
spindle bore: 82 mm
spindle nose: camlock 8 "
spindle speeds: (24) 9-1600 rpm (option 11-2000 u/min)
engine output: 5.5 kw (option: 7.5 kw) feed z-axis: (93) 0.028 6.43 mm / rev
feed x axis: (93) 0.012 2.73 mm / rev
thread, metric: (54) 0.5-224 mm
thread, witworth: (55) 72 - 1/8 tpi
thread, module: (54) 0.5-112 mm
thread, diametral pitch: (54) 64 - 1/4 d.p..
cross slide lxw: 650 x 230 mm
transversal carriage stroke: 340 mm
upper carriage lxw: 350 x 150 mm
upper carriage stroke: 150 mm
tailstock quill diameter: 85 mm
tailstock quill stroke: 200 mm
tailstock taper: mk 5
weight: 3,100 kg

facilities:
-movement of the tailstock pneumatically supported
-acceptance protocol according to din 8605, lathe with high accuracy
-mechanical dual clutch
-electromagnetic brake
-rapid traverse x - and z-axis
-electrical equipment of high quality brand components such as siemens/schneider
-lubrication of guideways via hand pump - reduction sleeve
-2 fixed centres
-all safety devices according to ce standards: rotary chuck guard secured with plexiglas window, limit microswitch. chisel holder protection with plexiglass. rear splash guard along the entire length. lead screw and spindle protection by photoelectric sensor (included in the emergency stop circuit). emergency off pushbutton.
-shaving container on wheels
-electric coolant system
-fixed bezel - revolving bezel
-control tool, acceptance protocol according to din, operating and maintenance manuals, complete electrical installation, machine manufactured according to ce standard in the latest version MADE IN ITALY MACHINE ACCORDING TO DIN 8606 TIP HEIGHT: 260 MM TURNING DIAMETER OVER BED: 520 MM SWING OVER CARRIAGE: 300 MM CENTRE DISTANCE: 1500 MM BED WIDTH: 400 MM SPINDLE BORE: 82 MM SPINDLE NOSE: CAMLOCK 8 " SPINDLE SPEEDS: (24) 9-1600 RPM (OPTION 11-2000 U/MIN) ENGINE OUTPUT: 5.5 KW (OPTION: 7.5 KW) FEED Z-AXIS: (93) 0.028 6.43 MM / REV FEED X AXIS: (93) 0.012 2.73 MM / REV THREAD, METRIC: (54) 0.5-224 MM THREAD, WITWORTH: (55) 72 - 1/8 TPI THREAD, MODULE: (54) 0.5-112 MM THREAD, DIAMETRAL PITCH: (54) 64 - 1/4 D.P.. CROSS SLIDE LXW: 650 X 230 MM TRANSVERSAL CARRIAGE STROKE: 340 MM UPPER CARRIAGE LXW: 350 X 150 MM UPPER CARRIAGE STROKE: 150 MM TAILSTOCK QUILL DIAMETER: 85 MM TAILSTOCK QUILL STROKE: 200 MM TAILSTOCK TAPER: MK 5 WEIGHT: 3,100 KG FACILITIES: -MOVEMENT OF THE TAILSTOCK PNEUMATICALLY SUPPORTED -ACCEPTANCE PROTOCOL ACCORDING TO DIN 8605, LATHE WITH HIGH ACCURACY -MECHANICAL DUAL CLUTCH -ELECTROMAGNETIC BRAKE -RAPID TRAVERSE X - AND Z-AXIS -ELECTRICAL EQUIPMENT OF HIGH QUALITY BRAND COMPONENTS SUCH AS SIEMENS/SCHNEIDER -LUBRICATION OF GUIDEWAYS VIA HAND PUMP - REDUCTION SLEEVE -2 FIXED CENTRES -ALL SAFETY DEVICES ACCORDING TO CE STANDARDS: ROTARY CHUCK GUARD SECURED WITH PLEXIGLAS WINDOW, LIMIT MICROSWITCH. CHISEL HOLDER PROTECTION WITH PLEXIGLASS. REAR SPLASH GUARD ALONG THE ENTIRE LENGTH. LEAD SCREW AND SPINDLE PROTECTION BY PHOTOELECTRIC SENSOR (INCLUDED IN THE EMERGENCY STOP CIRCUIT). EMERGENCY OFF PUSHBUTTON. -SHAVING CONTAINER ON WHEELS -ELECTRIC COOLANT SYSTEM -FIXED BEZEL - REVOLVING BEZEL -CONTROL TOOL, ACCEPTANCE PROTOCOL ACCORDING TO DIN, OPERATING AND MAINTENANCE MANUALS, COMPLETE ELECTRICAL INSTALLATION, MACHINE MANUFACTURED ACCORDING TO CE STANDARD IN THE LATEST VERSION
Vendedor: Weber Werkzeugmaschinen GbR
Año de construcción: usado
Precio: 14.340 €
Ubicación: Land-: 200 mm<br/>: 4 mm<br/>: 200 x 3 mm<br/>: 80 mm<br/>: 8 nm<br/>helical gear box wattdrive (made in austria)<br/>festo pneumatic equipment<br/>servo drive and control schneider electric<br/>7", colour touchscreen schneider electric<br/>4 gear rollers drive. prevents the separation of the rollers during piloting operation for higher accuracy<br/>free feeding speed 100mt/min<br/><br/>because the application areas are always very specific for each customer and require intense counseling, we kindly ask for your inquiry in order to make you an individual offer!<br/><br/>(sample photo)<br/><br/><br/><br/><br/><br/><br/><br/>sheet width: 200 mm<br/>min. sheet thickness: 0,4 mm<br/>max. sheet thickness: 4 mm<br/>max. section: 200 x 3 mm<br/>roll Ø: 80 mm<br/>motor torque: 8 nm<br/><br/><br/><br/> : 200 MM
: 4 MM
: 200 X 3 MM
: 80 MM
: 8 NM
HELICAL GEAR BOX WATTDRIVE (MADE IN AUSTRIA)
FESTO PNEUMATIC EQUIPMENT
SERVO DRIVE AND CONTROL SCHNEIDER ELECTRIC
7", COLOUR TOUCHSCREEN SCHNEIDER ELECTRIC
4 GEAR ROLLERS DRIVE. PREVENTS THE SEPARATION OF THE ROLLERS DURING PILOTING OPERATION FOR HIGHER ACCURACY
FREE FEEDING SPEED 100MT/MIN

BECAUSE THE APPLICATION AREAS ARE ALWAYS VERY SPECIFIC FOR EACH CUSTOMER AND REQUIRE INTENSE COUNSELING, WE KINDLY ASK FOR YOUR INQUIRY IN ORDER TO MAKE YOU AN INDIVIDUAL OFFER!

(SAMPLE PHOTO)







SHEET WIDTH: 200 MM
MIN. SHEET THICKNESS: 0,4 MM
MAX. SHEET THICKNESS: 4 MM
MAX. SECTION: 200 X 3 MM
ROLL Ø: 80 MM
MOTOR TORQUE: 8 NM



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Ubicación: Land-we have for sale:

2 areva switchgeaar
12kv
630amp busbar
2 x incoming loadbreak switch
1 x breaker feeder WE HAVE FOR SALE: 2 AREVA SWITCHGEAAR 12KV 630AMP BUSBAR 2 X INCOMING LOADBREAK SWITCH 1 X BREAKER FEEDER
Vendedor: GPE Global Power Engineer
Año de construcción: usado
Precio: 14.920 €
Ubicación: Land-: 300 mm<br/>: 3 mm<br/>: 300 x 3 mm<br/>: 80 mm<br/>: 8 nm<br/>helical gear box wattdrive (made in austria)<br/>festo pneumatic equipment<br/>servo drive and control schneider electric<br/>7", colour touchscreen schneider electric<br/>4 gear rollers drive. prevents the separation of the rollers during piloting operation for higher accuracy<br/>free feeding speed 100mt/min<br/><br/>because the application areas are always very specific for each customer and require intense counseling, we kindly ask for your inquiry in order to make you an individual offer!<br/><br/>(sample photo)<br/><br/><br/><br/><br/><br/><br/><br/>sheet width: 300 mm<br/>min. sheet thickness: 0,4 mm<br/>max. sheet thickness: 3 mm<br/>max. section: 300 x 3 mm<br/>roll Ø: 80 mm<br/>motor torque: 8 nm<br/><br/><br/><br/> : 300 MM
: 3 MM
: 300 X 3 MM
: 80 MM
: 8 NM
HELICAL GEAR BOX WATTDRIVE (MADE IN AUSTRIA)
FESTO PNEUMATIC EQUIPMENT
SERVO DRIVE AND CONTROL SCHNEIDER ELECTRIC
7", COLOUR TOUCHSCREEN SCHNEIDER ELECTRIC
4 GEAR ROLLERS DRIVE. PREVENTS THE SEPARATION OF THE ROLLERS DURING PILOTING OPERATION FOR HIGHER ACCURACY
FREE FEEDING SPEED 100MT/MIN

BECAUSE THE APPLICATION AREAS ARE ALWAYS VERY SPECIFIC FOR EACH CUSTOMER AND REQUIRE INTENSE COUNSELING, WE KINDLY ASK FOR YOUR INQUIRY IN ORDER TO MAKE YOU AN INDIVIDUAL OFFER!

(SAMPLE PHOTO)







SHEET WIDTH: 300 MM
MIN. SHEET THICKNESS: 0,4 MM
MAX. SHEET THICKNESS: 3 MM
MAX. SECTION: 300 X 3 MM
ROLL Ø: 80 MM
MOTOR TORQUE: 8 NM



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Precio: 150 €
Ubicación: type: est 1.6 after tgl 29968
nr: 7179 a
primary voltage: 380 v; 4.61 a
secondary voltage: 220 v; 729
power: 2.7 / 1,55 a
performance: 1600 / 3200 w
speed: 870 / 620 1 / min
new price. approx. eur500
weight: approx. 10 kg

state. from camp unused, ready to use, original box with storage stocks, see photo

more switches, circuit breakers, contactors, motor protection and engines available:

-driving motor sew k46 dt71d 4bmg 3 ~ 380v 0.37 kw 117 u/min
-electric motor fdr 160 dietz 22 kw 380/430v wave 40 mm lk 300 mm
-electric motor eex thurm kmrb 90 l2 220/380v 2, 1kw 2855u/min w. 26 mm
-electric motor evic msz 152 220/380 v 4.0 kw 14401 rpm shaft 24 mm
-centrifuge szb0 1000c 960 1 / min 6 loadings/h
-kod425 flange motor with brake gear motor 0,25 kw 2800 u i 66 =
-geared motor flange motor dc motor 75 w 2000/48,5u 10nm
-transformer fig. 3 ~ 20(15) kv / 400 v 630 kva year 2014
-1 x limit switch robotron 500v 6a ip 55 3,0 kw
-switch-disconnector schneider ins250 100 3interpack with sammelsch...
-sick retroreflective photoelectric w24-2 b 240 double lens new
-position switch schmersal 1s,1Ö,sprungschalt.m3v4d 330-11y-m20
-main switch disconnectors black kraus & naimer 40 a 600 v
-siemens contactor 3rt1017-1ap01 ac ~ 3 400 v 5.5 kw
-star triangle switch 25a 6; ready for use .gif" alt="Land-we offer:

from a business resolution spare parts stock

control transformer transformer est 1,6 1600/3200 va 380/220v 7,27a

manufacturer: electro - pgh "vparteitag" dresden
type: est 1.6 after tgl 29968
nr: 7179 a
primary voltage: 380 v; 4.61 a
secondary voltage: 220 v; 729
power: 2.7 / 1,55 a
performance: 1600 / 3200 w
speed: 870 / 620 1 / min
new price. approx. eur500
weight: approx. 10 kg

state. from camp unused, ready to use, original box with storage stocks, see photo

more switches, circuit breakers, contactors, motor protection and engines available:

-driving motor sew k46 dt71d 4bmg 3 ~ 380v 0.37 kw 117 u/min
-electric motor fdr 160 dietz 22 kw 380/430v wave 40 mm lk 300 mm
-electric motor eex thurm kmrb 90 l2 220/380v 2, 1kw 2855u/min w. 26 mm
-electric motor evic msz 152 220/380 v 4.0 kw 14401 rpm shaft 24 mm
-centrifuge szb0 1000c 960 1 / min 6 loadings/h
-kod425 flange motor with brake gear motor 0,25 kw 2800 u i 66 =
-geared motor flange motor dc motor 75 w 2000/48,5u 10nm
-transformer fig. 3 ~ 20(15) kv / 400 v 630 kva year 2014
-1 x limit switch robotron 500v 6a ip 55 3,0 kw
-switch-disconnector schneider ins250 100 3interpack with sammelsch...
-sick retroreflective photoelectric w24-2 b 240 double lens new
-position switch schmersal 1s,1Ö,sprungschalt.m3v4d 330-11y-m20
-main switch disconnectors black kraus & naimer 40 a 600 v
-siemens contactor 3rt1017-1ap01 ac ~ 3 400 v 5.5 kw
-star triangle switch 25a 6; ready for use " style="height: 18px;"> WE OFFER:

FROM A BUSINESS RESOLUTION SPARE PARTS STOCK

CONTROL TRANSFORMER TRANSFORMER EST 1,6 1600/3200 VA 380/220V 7,27A

MANUFACTURER: ELECTRO - PGH "VPARTEITAG" DRESDEN
TYPE: EST 1.6 AFTER TGL 29968
NR: 7179 A
PRIMARY VOLTAGE: 380 V; 4.61 A
SECONDARY VOLTAGE: 220 V; 729
POWER: 2.7 / 1,55 A
PERFORMANCE: 1600 / 3200 W
SPEED: 870 / 620 1 / MIN
NEW PRICE. APPROX. EUR500
WEIGHT: APPROX. 10 KG

STATE. FROM CAMP UNUSED, READY TO USE, ORIGINAL BOX WITH STORAGE STOCKS, SEE PHOTO

MORE SWITCHES, CIRCUIT BREAKERS, CONTACTORS, MOTOR PROTECTION AND ENGINES AVAILABLE:

-DRIVING MOTOR SEW K46 DT71D 4BMG 3 ~ 380V 0.37 KW 117 U/MIN
-ELECTRIC MOTOR FDR 160 DIETZ 22 KW 380/430V WAVE 40 MM LK 300 MM
-ELECTRIC MOTOR EEX THURM KMRB 90 L2 220/380V 2, 1KW 2855U/MIN W. 26 MM
-ELECTRIC MOTOR EVIC MSZ 152 220/380 V 4.0 KW 14401 RPM SHAFT 24 MM
-CENTRIFUGE SZB0 1000C 960 1 / MIN 6 LOADINGS/H
-KOD425 FLANGE MOTOR WITH BRAKE GEAR MOTOR 0,25 KW 2800 U I 66 =
-GEARED MOTOR FLANGE MOTOR DC MOTOR 75 W 2000/48,5U 10NM
-TRANSFORMER FIG. 3 ~ 20(15) KV / 400 V 630 KVA YEAR 2014
-1 X LIMIT SWITCH ROBOTRON 500V 6A IP 55 3,0 KW
-SWITCH-DISCONNECTOR SCHNEIDER INS250 100 3INTERPACK WITH SAMMELSCH...
-SICK RETROREFLECTIVE PHOTOELECTRIC W24-2 B 240 DOUBLE LENS NEW
-POSITION SWITCH SCHMERSAL 1S,1Ö,SPRUNGSCHALT.M3V4D 330-11Y-M20
-MAIN SWITCH DISCONNECTORS BLACK KRAUS & NAIMER 40 A 600 V
-SIEMENS CONTACTOR 3RT1017-1AP01 AC ~ 3 400 V 5.5 KW
-STAR TRIANGLE SWITCH 25A 6; READY FOR USE
Vendedor: MEDCO Congreß-und Handels GmbH Halle
Año de construcción: usado
Precio: 10.730 €
Ubicación: Land-: 4.000 kg<br/>: 50 - 600 mm<br/>motorized drive<br/>mechanical adjustable coil mandrel with 4 jaws<br/>schneider speed control for decoiling speed aswell as acceleration- and deceleration times<br/>photoelectric proximity ensor sick for sag control <br/><br/><br/>non motorized with pneumatic brake - price on request<br/>pneumatic hold down arm - price on request<br/><br/>double-head decoilers, as well as horizontal pallet decoilers on request<br/><br/>because the application areas are always very specific for each customer and require intense counseling, we kindly ask for your inquiry in order to make you an individual offer!<br/><br/>(sample photos)<br/><br/><br/><br/><br/><br/><br/><br/>max. coil weight: 4.000 kg<br/>coil width: 50 - 600 mm<br/><br/><br/><br/> : 4.000 KG
: 50 - 600 MM
MOTORIZED DRIVE
MECHANICAL ADJUSTABLE COIL MANDREL WITH 4 JAWS
SCHNEIDER SPEED CONTROL FOR DECOILING SPEED ASWELL AS ACCELERATION- AND DECELERATION TIMES
PHOTOELECTRIC PROXIMITY ENSOR SICK FOR SAG CONTROL


NON MOTORIZED WITH PNEUMATIC BRAKE - PRICE ON REQUEST
PNEUMATIC HOLD DOWN ARM - PRICE ON REQUEST

DOUBLE-HEAD DECOILERS, AS WELL AS HORIZONTAL PALLET DECOILERS ON REQUEST

BECAUSE THE APPLICATION AREAS ARE ALWAYS VERY SPECIFIC FOR EACH CUSTOMER AND REQUIRE INTENSE COUNSELING, WE KINDLY ASK FOR YOUR INQUIRY IN ORDER TO MAKE YOU AN INDIVIDUAL OFFER!

(SAMPLE PHOTOS)







MAX. COIL WEIGHT: 4.000 KG
COIL WIDTH: 50 - 600 MM



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Precio: 150 €
Ubicación: Land-we offer:<br/>  <br/>  electric motor evic msz 152 220/380 v 4.0 kw 14401 rpm shaft 24 mm<br/>  <br/>  the electric motor comes from a wallpaper factory spare parts stock. he is in stock. outwardly he is dusty due to storage. .<br/>  <br/>  technical data<br/>  electric motor: msz 152<br/>  manufacturer: evic budapest<br/>  no. 534210<br/>  year of constr.: k.a..<br/>  voltage: 220v / 380v 3 ~ delta/star<br/>  power: 4,0 kw<br/>  speed: 1440 1/min<br/>  cos phi: 0.83<br/>  power: 15.2 / 8.8 delta/star<br/>  manufactured by: k. a.<br/>  shaft diameter: 28 mm<br/>  new price: eur250<br/>  weight: approx. 40 kg<br/>  <br/>  more advertised technical assets and metal working machinery in the range as follows:<br/>  <br/>  -siemens electric motor 1 la5130-4ca70 380/660 v 5.5 kw 1450 1/min<br/>  -electric motor k21r ip55 b3 520 kg 280 s4 400/690 v 75 kw 1480 1/min<br/>  -geared motor gargate 105 w wk1777504 with gear and brake<br/>  -switching unit contactor solenoid jungheinrich 24v 150 / 300 a eur50<br/>  -forklift linde h30t with gas tank, 2005, trip lex mast bra approx. 10000 h<br/>  -forklift yale glp16 af duplex mast year 98 sideshift<br/>  -shears wmw veb fritz heckert type sctp 16 x 3150 bj. 1984<br/>  -electric motor thurm kmb 100 220/380 v 1,0 kw 2051/min with or without claw<br/>  -1 x limit switch robotron 500v 6a ip 55 3.0 kw eur6<br/>  -switch-disconnector schneider ins250 100 3interpack with sammelsch... eur90<br/>  -sick retroreflective photoelectric w24-2 b 240 double lens new eur75<br/>  -position switch schmersal 1s,1oe,sp WE OFFER:

ELECTRIC MOTOR EVIC MSZ 152 220/380 V 4.0 KW 14401 RPM SHAFT 24 MM

THE ELECTRIC MOTOR COMES FROM A WALLPAPER FACTORY SPARE PARTS STOCK. HE IS IN STOCK. OUTWARDLY HE IS DUSTY DUE TO STORAGE. .

TECHNICAL DATA
ELECTRIC MOTOR: MSZ 152
MANUFACTURER: EVIC BUDAPEST
NO. 534210
YEAR OF CONSTR.: K.A..
VOLTAGE: 220V / 380V 3 ~ DELTA/STAR
POWER: 4,0 KW
SPEED: 1440 1/MIN
COS PHI: 0.83
POWER: 15.2 / 8.8 DELTA/STAR
MANUFACTURED BY: K. A.
SHAFT DIAMETER: 28 MM
NEW PRICE: EUR250
WEIGHT: APPROX. 40 KG

MORE ADVERTISED TECHNICAL ASSETS AND METAL WORKING MACHINERY IN THE RANGE AS FOLLOWS:

-SIEMENS ELECTRIC MOTOR 1 LA5130-4CA70 380/660 V 5.5 KW 1450 1/MIN
-ELECTRIC MOTOR K21R IP55 B3 520 KG 280 S4 400/690 V 75 KW 1480 1/MIN
-GEARED MOTOR GARGATE 105 W WK1777504 WITH GEAR AND BRAKE
-SWITCHING UNIT CONTACTOR SOLENOID JUNGHEINRICH 24V 150 / 300 A EUR50
-FORKLIFT LINDE H30T WITH GAS TANK, 2005, TRIP LEX MAST BRA APPROX. 10000 H
-FORKLIFT YALE GLP16 AF DUPLEX MAST YEAR 98 SIDESHIFT
-SHEARS WMW VEB FRITZ HECKERT TYPE SCTP 16 X 3150 BJ. 1984
-ELECTRIC MOTOR THURM KMB 100 220/380 V 1,0 KW 2051/MIN WITH OR WITHOUT CLAW
-1 X LIMIT SWITCH ROBOTRON 500V 6A IP 55 3.0 KW EUR6
-SWITCH-DISCONNECTOR SCHNEIDER INS250 100 3INTERPACK WITH SAMMELSCH... EUR90
-SICK RETROREFLECTIVE PHOTOELECTRIC W24-2 B 240 DOUBLE LENS NEW EUR75
-POSITION SWITCH SCHMERSAL 1S,1OE,SP
Vendedor: MEDCO Congreß-und Handels GmbH Halle
Año de construcción: usado
Precio: 5.110 €
Ubicación: Land-: 1.250 kg<br/>: 50 - 400 mm<br/>motorized drive<br/>mechanical adjustable coil mandrel with 4 jaws<br/>schneider speed control for decoiling speed aswell as acceleration- and deceleration times<br/>photoelectric proximity ensor sick for sag control <br/><br/><br/>non motorized with pneumatic brake - price on request<br/>pneumatic hold down arm - price on request<br/><br/>double-head decoilers, as well as horizontal pallet decoilers on request<br/><br/>because the application areas are always very specific for each customer and require intense counseling, we kindly ask for your inquiry in order to make you an individual offer!<br/><br/>(sample photos)<br/><br/><br/><br/><br/><br/><br/><br/>max. coil weight: 1.250 kg<br/>coil width: 50 - 400 mm<br/><br/><br/><br/> : 1.250 KG
: 50 - 400 MM
MOTORIZED DRIVE
MECHANICAL ADJUSTABLE COIL MANDREL WITH 4 JAWS
SCHNEIDER SPEED CONTROL FOR DECOILING SPEED ASWELL AS ACCELERATION- AND DECELERATION TIMES
PHOTOELECTRIC PROXIMITY ENSOR SICK FOR SAG CONTROL


NON MOTORIZED WITH PNEUMATIC BRAKE - PRICE ON REQUEST
PNEUMATIC HOLD DOWN ARM - PRICE ON REQUEST

DOUBLE-HEAD DECOILERS, AS WELL AS HORIZONTAL PALLET DECOILERS ON REQUEST

BECAUSE THE APPLICATION AREAS ARE ALWAYS VERY SPECIFIC FOR EACH CUSTOMER AND REQUIRE INTENSE COUNSELING, WE KINDLY ASK FOR YOUR INQUIRY IN ORDER TO MAKE YOU AN INDIVIDUAL OFFER!

(SAMPLE PHOTOS)







MAX. COIL WEIGHT: 1.250 KG
COIL WIDTH: 50 - 400 MM



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Precio: 100 €
Ubicación: Land-we offer:<br/>  <br/>  electric motor ma90l244 220/3800 v 2.2 kw 2880 1/min shaft 24 mm<br/>  <br/>  the electric motor comes from a wallpaper factory spare parts stock. he is funktlagerware. outwardly he is dusty due to storage. .<br/>  <br/>  electric motor: ma90l244<br/>  : manufacturer no<br/>  no. ka<br/>  year of constr.: ka<br/>  voltage: 220v / 380v 3 ~ delta/star<br/>  power: 2.2 kw<br/>  speed: 2880 1/min<br/>  cos phi: 0.86<br/>  power: 14.9 / 8.5 delta/star<br/>  weight: approx. 22 kg<br/>  <br/>  more advertised technical assets, workshop equipment and metal working machinery in the range as follows:<br/>  <br/>  -siemens electric motor 1 la5130-4ca70 380/660 v 5.5 kw 1450 1/min<br/>  -electric motor k21r ip55 b3 520 kg 280 s4 400/690 v 75 kw 1480 1/min<br/>  -geared motor gargate 105 w wk1777504 with gear and brake<br/>  -switching unit contactor solenoid jungheinrich 24v 150 / 300 a eur50<br/>  -forklift linde e 16-01 trip lex mast year 2007 tricycle bra 10016<br/>  -forklift linde h30t with gas tank, 2005, trip lex mast bra approx. 10000 h<br/>  -forklift yale glp16 af duplex mast year 98 sideshift<br/>  -shears wmw veb fritz heckert type sctp 16 x 3150 bj. 1984<br/>  -heat exchanger air heater fan heater gea happel 87 kw 9840 m³/h<br/>  -1 x limit switch robotron 500v 6a ip 55 3.0 kw eur6<br/>  -switch-disconnector schneider ins250 100 3interpack with sammelsch... eur90<br/>  -sick retroreflective photoelectric w24-2 b 240 double lens new eur75<br/>  -position switch schmersal 1s,1oe, WE OFFER:

ELECTRIC MOTOR MA90L244 220/3800 V 2.2 KW 2880 1/MIN SHAFT 24 MM

THE ELECTRIC MOTOR COMES FROM A WALLPAPER FACTORY SPARE PARTS STOCK. HE IS FUNKTLAGERWARE. OUTWARDLY HE IS DUSTY DUE TO STORAGE. .

ELECTRIC MOTOR: MA90L244
: MANUFACTURER NO
NO. KA
YEAR OF CONSTR.: KA
VOLTAGE: 220V / 380V 3 ~ DELTA/STAR
POWER: 2.2 KW
SPEED: 2880 1/MIN
COS PHI: 0.86
POWER: 14.9 / 8.5 DELTA/STAR
WEIGHT: APPROX. 22 KG

MORE ADVERTISED TECHNICAL ASSETS, WORKSHOP EQUIPMENT AND METAL WORKING MACHINERY IN THE RANGE AS FOLLOWS:

-SIEMENS ELECTRIC MOTOR 1 LA5130-4CA70 380/660 V 5.5 KW 1450 1/MIN
-ELECTRIC MOTOR K21R IP55 B3 520 KG 280 S4 400/690 V 75 KW 1480 1/MIN
-GEARED MOTOR GARGATE 105 W WK1777504 WITH GEAR AND BRAKE
-SWITCHING UNIT CONTACTOR SOLENOID JUNGHEINRICH 24V 150 / 300 A EUR50
-FORKLIFT LINDE E 16-01 TRIP LEX MAST YEAR 2007 TRICYCLE BRA 10016
-FORKLIFT LINDE H30T WITH GAS TANK, 2005, TRIP LEX MAST BRA APPROX. 10000 H
-FORKLIFT YALE GLP16 AF DUPLEX MAST YEAR 98 SIDESHIFT
-SHEARS WMW VEB FRITZ HECKERT TYPE SCTP 16 X 3150 BJ. 1984
-HEAT EXCHANGER AIR HEATER FAN HEATER GEA HAPPEL 87 KW 9840 M³/H
-1 X LIMIT SWITCH ROBOTRON 500V 6A IP 55 3.0 KW EUR6
-SWITCH-DISCONNECTOR SCHNEIDER INS250 100 3INTERPACK WITH SAMMELSCH... EUR90
-SICK RETROREFLECTIVE PHOTOELECTRIC W24-2 B 240 DOUBLE LENS NEW EUR75
-POSITION SWITCH SCHMERSAL 1S,1OE,
Vendedor: MEDCO Congreß-und Handels GmbH Halle
Año de construcción: usado
Precio: 15.500 €
Ubicación: Land-: 400 mm<br/>: 3 mm<br/>: 400 x 3 mm<br/>: 80 mm<br/>: 10 nm<br/>helical gear box wattdrive (made in austria)<br/>festo pneumatic equipment<br/>servo drive and control schneider electric<br/>7", colour touchscreen schneider electric<br/>4 gear rollers drive. prevents the separation of the rollers during piloting operation for higher accuracy<br/>free feeding speed 100mt/min<br/><br/>because the application areas are always very specific for each customer and require intense counseling, we kindly ask for your inquiry in order to make you an individual offer!<br/><br/>(sample photo)<br/><br/><br/><br/><br/><br/><br/><br/>sheet width: 400 mm<br/>min. sheet thickness: 0,4 mm<br/>max. sheet thickness: 3 mm<br/>max. section: 400 x 3 mm<br/>roll Ø: 80 mm<br/>motor torque: 10 nm<br/><br/><br/><br/> : 400 MM
: 3 MM
: 400 X 3 MM
: 80 MM
: 10 NM
HELICAL GEAR BOX WATTDRIVE (MADE IN AUSTRIA)
FESTO PNEUMATIC EQUIPMENT
SERVO DRIVE AND CONTROL SCHNEIDER ELECTRIC
7", COLOUR TOUCHSCREEN SCHNEIDER ELECTRIC
4 GEAR ROLLERS DRIVE. PREVENTS THE SEPARATION OF THE ROLLERS DURING PILOTING OPERATION FOR HIGHER ACCURACY
FREE FEEDING SPEED 100MT/MIN

BECAUSE THE APPLICATION AREAS ARE ALWAYS VERY SPECIFIC FOR EACH CUSTOMER AND REQUIRE INTENSE COUNSELING, WE KINDLY ASK FOR YOUR INQUIRY IN ORDER TO MAKE YOU AN INDIVIDUAL OFFER!

(SAMPLE PHOTO)







SHEET WIDTH: 400 MM
MIN. SHEET THICKNESS: 0,4 MM
MAX. SHEET THICKNESS: 3 MM
MAX. SECTION: 400 X 3 MM
ROLL Ø: 80 MM
MOTOR TORQUE: 10 NM



Vendedor: HESSE+CO GesmbH
Año de construcción: usado
Precio: 190 €
Ubicación: Land-we offer:<br/>  <br/>  electric motor exe thurm kmrb 90 l2 220/380v 2, 1kw 28551 rpm w. 26 mm<br/>  <br/>  the electric motor comes from a wallpaper factory spare parts stock. he is in stock. outwardly he is dusty due to storage. .<br/>  <br/>  technical data<br/>  electric motor: thurm kmrb ex 90 l2<br/>  manufacturer: veb electric motors thurm<br/>  no. 169 58<br/>  year of construction: 1987.<br/>  voltage: 220v / 380v 3 ~ delta/star<br/>  capacity: 2.1 kw<br/>  speed: 2855 1/min<br/>  cos phi: 0.91<br/>  power: 7,6 / 4.4 delta/star<br/>  manufactured by: tgl 32707<br/>  wellw: 26 mm<br/>  new price: 250-eur500<br/>  weight: 23.5 kg<br/>  <br/>  more advertised technical assets and metal working machinery in the range as follows:<br/>  <br/>  -siemens electric motor 1 la5130-4ca70 380/660 v 5.5 kw 1450 1/min<br/>  -electric motor k21r ip55 b3 520 kg 280 s4 400/690 v 75 kw 1480 1/min<br/>  -geared motor gargate 105 w wk1777504 with gear and brake<br/>  -switching unit contactor solenoid jungheinrich 24v 150 / 300 a eur50<br/>  -forklift linde h30t with gas tank, 2005, trip lex mast bra approx. 10000 h<br/>  -forklift yale glp16 af duplex mast year 98 sideshift<br/>  -shears wmw veb fritz heckert type sctp 16 x 3150 bj. 1984<br/>  -electric motor evic msz 152 220/380 v 4.0 kw 14401 rpm shaft 24 mm<br/>  -1 x limit switch robotron 500v 6a ip 55 3,0 kw<br/>  -switch-disconnector schneider ins250 100 3interpack with sammelsch...<br/>  -sick retroreflective photoelectric w24-2 b 240 dual lens<br/>  -position switch schmersal WE OFFER:

ELECTRIC MOTOR EXE THURM KMRB 90 L2 220/380V 2, 1KW 28551 RPM W. 26 MM

THE ELECTRIC MOTOR COMES FROM A WALLPAPER FACTORY SPARE PARTS STOCK. HE IS IN STOCK. OUTWARDLY HE IS DUSTY DUE TO STORAGE. .

TECHNICAL DATA
ELECTRIC MOTOR: THURM KMRB EX 90 L2
MANUFACTURER: VEB ELECTRIC MOTORS THURM
NO. 169 58
YEAR OF CONSTRUCTION: 1987.
VOLTAGE: 220V / 380V 3 ~ DELTA/STAR
CAPACITY: 2.1 KW
SPEED: 2855 1/MIN
COS PHI: 0.91
POWER: 7,6 / 4.4 DELTA/STAR
MANUFACTURED BY: TGL 32707
WELLW: 26 MM
NEW PRICE: 250-EUR500
WEIGHT: 23.5 KG

MORE ADVERTISED TECHNICAL ASSETS AND METAL WORKING MACHINERY IN THE RANGE AS FOLLOWS:

-SIEMENS ELECTRIC MOTOR 1 LA5130-4CA70 380/660 V 5.5 KW 1450 1/MIN
-ELECTRIC MOTOR K21R IP55 B3 520 KG 280 S4 400/690 V 75 KW 1480 1/MIN
-GEARED MOTOR GARGATE 105 W WK1777504 WITH GEAR AND BRAKE
-SWITCHING UNIT CONTACTOR SOLENOID JUNGHEINRICH 24V 150 / 300 A EUR50
-FORKLIFT LINDE H30T WITH GAS TANK, 2005, TRIP LEX MAST BRA APPROX. 10000 H
-FORKLIFT YALE GLP16 AF DUPLEX MAST YEAR 98 SIDESHIFT
-SHEARS WMW VEB FRITZ HECKERT TYPE SCTP 16 X 3150 BJ. 1984
-ELECTRIC MOTOR EVIC MSZ 152 220/380 V 4.0 KW 14401 RPM SHAFT 24 MM
-1 X LIMIT SWITCH ROBOTRON 500V 6A IP 55 3,0 KW
-SWITCH-DISCONNECTOR SCHNEIDER INS250 100 3INTERPACK WITH SAMMELSCH...
-SICK RETROREFLECTIVE PHOTOELECTRIC W24-2 B 240 DUAL LENS
-POSITION SWITCH SCHMERSAL
Vendedor: MEDCO Congreß-und Handels GmbH Halle
Año de construcción: usado
Ubicación: Land-pressure:300 t<br/>chamfer lenght:4300 mm<br/>distance between columns:3700 mm<br/>stroke:400 mm<br/>dayligth:650 mm<br/>throat:400 mm<br/>ajustment speed:180 mm/sec<br/>working feed:0 - 10 mm/sec<br/>return speed:115 mm/sec<br/>total power requirement:30 kw<br/>weight of the machine ca.:26 t<br/>dimensions of the machine ca.:5,3 x 2,0 x 3,55 m<br/>tank capacity:345 l<br/>back stop - adjustable:750 mm<br/>capacity r-axis:150 mm<br/><br/>x and r controlled backstop type bga x axis for the insertion depth, travel range 750 mm positioning accuracy x-axis +/- 0.05 mm travel speed x-axis 500 mm / sec r-axis for the finger height, travel range 150 mm positioning accuracy r-axis +/- 0.02 mm travel speed r-axis 170 mm / sec front and back lighting electrical components: schneider electricsa (telemecanique) hydraulic components: ce safety device according to din 12622: 2001 front with laser beam on the upper tool manufacturer fiessler model akas lc-ii m backside with light curtain manufacturer pilz model 630765 type 4 security plc manufacturer fiessler model fpsc foot switch with safety pallets ce - mark and ce - declaration of conformity german manual  delem 3-d control unit da69t touchscreen version with mobile control panel 3d touchscreen control with lcd color display - 17 inch tft, high brightness - 1280 x 1024 pixels, 32 bit color - full touchscreen control (ir-touch) - storage capacity 1 gb - 3d graphical acceleration equipment: - 2d graphical touch screen programming - 3d representation in simulation and production - 17-inch tft color display with high resolution - complete windows application suite - compatible with delem modusys - usb, peripheral interface - open system architecture - sensor bending and correction interface programming - alphanumeric product name - product programming and presentation in real size - automatic calculation of a bending sequence - flat-push product programming - a page programming table - graphic product and tool selection - free material properties - free material programming - product counter - product notes tools - graphical tool configuration - multiple tool stations - tool segmentation - alphanum. tool identification - free graphical tool programming - flat and radius tools - support tool adapter calculation - tool safety zones - pressing force - bending tolerance - camber adjustment - extended length - embossing force, flat pressing, automatic round bending calculation - radius programming - bending tolerance table - learned angle correction  digital angle measuring device with angle correction react for press brakes, prl / prcn / prcb series with control delem da58t, da66t and da69t. angle gauge with direct cabling measuring the bent angles with feedback to the control - this calculates the necessary correction value. transfer of the data to the cnc control by cable the usb port on the control front  basic backrest version bga with additional r-axis for press brakes hezinger-pressline, prcn series type of backstop type bga adjustment speed x-axis 500 mm / sec positioning accuracy x-axis +/- 0.05 mm adjustment range r-axis stepless 150 mm adjustment speed r-axis 170 mm / sec positioning accuracy +/- 0.20 mm repeatability + / - 0.20 mm stop finger with 2 bearing surfaces  rear stop with additional z1-z2 axle version x-r-z1-z2 independent positioning of the stop fingers in the width travel range z1-z2 approx. 3000 mm travel speed 2000 mm / sec positioning accuracy + / - 0,10 mm repeatability + / - 0,10 mm type of backstop type bga stop finger with 2 bearing surfaces  pneumatic support arms with ball rollers for support of the inserted sheets installed on the backstops suitable for controlled r-axes activation and deactivation via cnc control area of ??application max. 300 mm  cnc bending aid system for press brakes, 2 motor units data input via cnc control, load at approx. 360 kg / unit working range approx. 900 to 1,500 mm width per arm approx. 350 mm height adjustment +/- 60 mm depth adjustment 0-60 mm laterally adjustable over the entire machine length support arms with ball circulating spindles and linear motors accuracy at +/- 0.2 mm in the range of 0 - 60 ° including a parking position for one edition on the right and on the left  cnc crowning for cnc press brakes hezinger-pressline prcn / prcb / prl series wedge camber integrated in the wila system in the table no loss of installation height adjustment via electric servomotor, controlled by the cnc control  hydraulic upper tool clamping wila new standard for press brakes hezinger-pressline - fastest tool change -automatic clamping, adjustment and alignment -individual clamping of the individual segments -vertical and horizontal tool change including hydraulic unit folding length 4.300 mm load capacity per meter 1,800 kn / m PRESSURE:300 T
CHAMFER LENGHT:4300 MM
DISTANCE BETWEEN COLUMNS:3700 MM
STROKE:400 MM
DAYLIGTH:650 MM
THROAT:400 MM
AJUSTMENT SPEED:180 MM/SEC
WORKING FEED:0 - 10 MM/SEC
RETURN SPEED:115 MM/SEC
TOTAL POWER REQUIREMENT:30 KW
WEIGHT OF THE MACHINE CA.:26 T
DIMENSIONS OF THE MACHINE CA.:5,3 X 2,0 X 3,55 M
TANK CAPACITY:345 L
BACK STOP - ADJUSTABLE:750 MM
CAPACITY R-AXIS:150 MM

X AND R CONTROLLED BACKSTOP TYPE BGA X AXIS FOR THE INSERTION DEPTH, TRAVEL RANGE 750 MM POSITIONING ACCURACY X-AXIS +/- 0.05 MM TRAVEL SPEED X-AXIS 500 MM / SEC R-AXIS FOR THE FINGER HEIGHT, TRAVEL RANGE 150 MM POSITIONING ACCURACY R-AXIS +/- 0.02 MM TRAVEL SPEED R-AXIS 170 MM / SEC FRONT AND BACK LIGHTING ELECTRICAL COMPONENTS: SCHNEIDER ELECTRICSA (TELEMECANIQUE) HYDRAULIC COMPONENTS: CE SAFETY DEVICE ACCORDING TO DIN 12622: 2001 FRONT WITH LASER BEAM ON THE UPPER TOOL MANUFACTURER FIESSLER MODEL AKAS LC-II M BACKSIDE WITH LIGHT CURTAIN MANUFACTURER PILZ MODEL 630765 TYPE 4 SECURITY PLC MANUFACTURER FIESSLER MODEL FPSC FOOT SWITCH WITH SAFETY PALLETS CE - MARK AND CE - DECLARATION OF CONFORMITY GERMAN MANUAL DELEM 3-D CONTROL UNIT DA69T TOUCHSCREEN VERSION WITH MOBILE CONTROL PANEL 3D TOUCHSCREEN CONTROL WITH LCD COLOR DISPLAY - 17 INCH TFT, HIGH BRIGHTNESS - 1280 X 1024 PIXELS, 32 BIT COLOR - FULL TOUCHSCREEN CONTROL (IR-TOUCH) - STORAGE CAPACITY 1 GB - 3D GRAPHICAL ACCELERATION EQUIPMENT: - 2D GRAPHICAL TOUCH SCREEN PROGRAMMING - 3D REPRESENTATION IN SIMULATION AND PRODUCTION - 17-INCH TFT COLOR DISPLAY WITH HIGH RESOLUTION - COMPLETE WINDOWS APPLICATION SUITE - COMPATIBLE WITH DELEM MODUSYS - USB, PERIPHERAL INTERFACE - OPEN SYSTEM ARCHITECTURE - SENSOR BENDING AND CORRECTION INTERFACE PROGRAMMING - ALPHANUMERIC PRODUCT NAME - PRODUCT PROGRAMMING AND PRESENTATION IN REAL SIZE - AUTOMATIC CALCULATION OF A BENDING SEQUENCE - FLAT-PUSH PRODUCT PROGRAMMING - A PAGE PROGRAMMING TABLE - GRAPHIC PRODUCT AND TOOL SELECTION - FREE MATERIAL PROPERTIES - FREE MATERIAL PROGRAMMING - PRODUCT COUNTER - PRODUCT NOTES TOOLS - GRAPHICAL TOOL CONFIGURATION - MULTIPLE TOOL STATIONS - TOOL SEGMENTATION - ALPHANUM. TOOL IDENTIFICATION - FREE GRAPHICAL TOOL PROGRAMMING - FLAT AND RADIUS TOOLS - SUPPORT TOOL ADAPTER CALCULATION - TOOL SAFETY ZONES - PRESSING FORCE - BENDING TOLERANCE - CAMBER ADJUSTMENT - EXTENDED LENGTH - EMBOSSING FORCE, FLAT PRESSING, AUTOMATIC ROUND BENDING CALCULATION - RADIUS PROGRAMMING - BENDING TOLERANCE TABLE - LEARNED ANGLE CORRECTION DIGITAL ANGLE MEASURING DEVICE WITH ANGLE CORRECTION REACT FOR PRESS BRAKES, PRL / PRCN / PRCB SERIES WITH CONTROL DELEM DA58T, DA66T AND DA69T. ANGLE GAUGE WITH DIRECT CABLING MEASURING THE BENT ANGLES WITH FEEDBACK TO THE CONTROL - THIS CALCULATES THE NECESSARY CORRECTION VALUE. TRANSFER OF THE DATA TO THE CNC CONTROL BY CABLE THE USB PORT ON THE CONTROL FRONT BASIC BACKREST VERSION BGA WITH ADDITIONAL R-AXIS FOR PRESS BRAKES HEZINGER-PRESSLINE, PRCN SERIES TYPE OF BACKSTOP TYPE BGA ADJUSTMENT SPEED X-AXIS 500 MM / SEC POSITIONING ACCURACY X-AXIS +/- 0.05 MM ADJUSTMENT RANGE R-AXIS STEPLESS 150 MM ADJUSTMENT SPEED R-AXIS 170 MM / SEC POSITIONING ACCURACY +/- 0.20 MM REPEATABILITY + / - 0.20 MM STOP FINGER WITH 2 BEARING SURFACES REAR STOP WITH ADDITIONAL Z1-Z2 AXLE VERSION X-R-Z1-Z2 INDEPENDENT POSITIONING OF THE STOP FINGERS IN THE WIDTH TRAVEL RANGE Z1-Z2 APPROX. 3000 MM TRAVEL SPEED 2000 MM / SEC POSITIONING ACCURACY + / - 0,10 MM REPEATABILITY + / - 0,10 MM TYPE OF BACKSTOP TYPE BGA STOP FINGER WITH 2 BEARING SURFACES PNEUMATIC SUPPORT ARMS WITH BALL ROLLERS FOR SUPPORT OF THE INSERTED SHEETS INSTALLED ON THE BACKSTOPS SUITABLE FOR CONTROLLED R-AXES ACTIVATION AND DEACTIVATION VIA CNC CONTROL AREA OF ??APPLICATION MAX. 300 MM CNC BENDING AID SYSTEM FOR PRESS BRAKES, 2 MOTOR UNITS DATA INPUT VIA CNC CONTROL, LOAD AT APPROX. 360 KG / UNIT WORKING RANGE APPROX. 900 TO 1,500 MM WIDTH PER ARM APPROX. 350 MM HEIGHT ADJUSTMENT +/- 60 MM DEPTH ADJUSTMENT 0-60 MM LATERALLY ADJUSTABLE OVER THE ENTIRE MACHINE LENGTH SUPPORT ARMS WITH BALL CIRCULATING SPINDLES AND LINEAR MOTORS ACCURACY AT +/- 0.2 MM IN THE RANGE OF 0 - 60 ° INCLUDING A PARKING POSITION FOR ONE EDITION ON THE RIGHT AND ON THE LEFT CNC CROWNING FOR CNC PRESS BRAKES HEZINGER-PRESSLINE PRCN / PRCB / PRL SERIES WEDGE CAMBER INTEGRATED IN THE WILA SYSTEM IN THE TABLE NO LOSS OF INSTALLATION HEIGHT ADJUSTMENT VIA ELECTRIC SERVOMOTOR, CONTROLLED BY THE CNC CONTROL HYDRAULIC UPPER TOOL CLAMPING WILA NEW STANDARD FOR PRESS BRAKES HEZINGER-PRESSLINE - FASTEST TOOL CHANGE -AUTOMATIC CLAMPING, ADJUSTMENT AND ALIGNMENT -INDIVIDUAL CLAMPING OF THE INDIVIDUAL SEGMENTS -VERTICAL AND HORIZONTAL TOOL CHANGE INCLUDING HYDRAULIC UNIT FOLDING LENGTH 4.300 MM LOAD CAPACITY PER METER 1,800 KN / M
Vendedor: Heinz Sanders GmbH
Año de construcción: usado
Precio: 690 €
Ubicación: Land-we offer:<br/>  <br/>  electric motor flange motor fom 200 18.5 kw 380/420v / 660-720v shaft 55 mm<br/>  bolt circle diameter 350 mm<br/>  <br/>  the electric motor comes from a wallpaper factory spare parts stock. he is in stock. he is dusty externally due to storage. .<br/>  <br/>  technical data<br/>  electric motor type: fom 200 a 6<br/>  manufacturer:??? motors gmbh...<br/>  no. 04080401<br/>  year of manufacture:????<br/>  voltage: 380/420v / 660-720v 50/60 hz<br/>  drtehzahl: 970 rpm at 50 hz<br/>  power: 18.5 kw s1 at 50 hz<br/>  cos phi: 0.81<br/>  power: 38.6 / 21.1 a<br/>  ip 55<br/>  shaft diameter: 55 mm<br/>  bolt circle diameter: 350 mm<br/>  <br/>  weight: 225 kg<br/>  <br/>  more assets at ms written out as follows in the offer:<br/>  <br/>  -hydraulic aggregate Ørsta leipzig 4/83 160 bar 1986 100 kg<br/>  -horizontal grinder band cs411 200x75cm x 40 380v 2.2 kw...<br/>  -truck iveco eurocargo 75e16/p with liftgate deregistered 245000 km<br/>  -forklift yale glp16 af duplex mast year 98 sideshift<br/>  -shears wmw veb fritz heckert type sctp 16 x 3150 bj. 1984<br/>  -notching machine with adjustable angles up to 4 mm<br/>  -eccentric press ambold to edsp 55, pressing force 55 mp thickness up to 4, 5 mm<br/>  -eccentric press hamilton 40skr, pressing force: 40 t<br/>  cross traverse mkf with adjustable hook 1200 kg d = 500-1400 mm<br/>  -bending machine banning<br/>  -switching unit contactor solenoid jungheinrich 24v 150 / 300 a eur50<br/>  -1 x limit switch robotron 500v 6a ip 55 3.0 kw eur6<br/>  -switch-disconnector schneider ins250 100 3interpack with WE OFFER:

ELECTRIC MOTOR FLANGE MOTOR FOM 200 18.5 KW 380/420V / 660-720V SHAFT 55 MM
BOLT CIRCLE DIAMETER 350 MM

THE ELECTRIC MOTOR COMES FROM A WALLPAPER FACTORY SPARE PARTS STOCK. HE IS IN STOCK. HE IS DUSTY EXTERNALLY DUE TO STORAGE. .

TECHNICAL DATA
ELECTRIC MOTOR TYPE: FOM 200 A 6
MANUFACTURER:??? MOTORS GMBH...
NO. 04080401
YEAR OF MANUFACTURE:????
VOLTAGE: 380/420V / 660-720V 50/60 HZ
DRTEHZAHL: 970 RPM AT 50 HZ
POWER: 18.5 KW S1 AT 50 HZ
COS PHI: 0.81
POWER: 38.6 / 21.1 A
IP 55
SHAFT DIAMETER: 55 MM
BOLT CIRCLE DIAMETER: 350 MM

WEIGHT: 225 KG

MORE ASSETS AT MS WRITTEN OUT AS FOLLOWS IN THE OFFER:

-HYDRAULIC AGGREGATE ØRSTA LEIPZIG 4/83 160 BAR 1986 100 KG
-HORIZONTAL GRINDER BAND CS411 200X75CM X 40 380V 2.2 KW...
-TRUCK IVECO EUROCARGO 75E16/P WITH LIFTGATE DEREGISTERED 245000 KM
-FORKLIFT YALE GLP16 AF DUPLEX MAST YEAR 98 SIDESHIFT
-SHEARS WMW VEB FRITZ HECKERT TYPE SCTP 16 X 3150 BJ. 1984
-NOTCHING MACHINE WITH ADJUSTABLE ANGLES UP TO 4 MM
-ECCENTRIC PRESS AMBOLD TO EDSP 55, PRESSING FORCE 55 MP THICKNESS UP TO 4, 5 MM
-ECCENTRIC PRESS HAMILTON 40SKR, PRESSING FORCE: 40 T
CROSS TRAVERSE MKF WITH ADJUSTABLE HOOK 1200 KG D = 500-1400 MM
-BENDING MACHINE BANNING
-SWITCHING UNIT CONTACTOR SOLENOID JUNGHEINRICH 24V 150 / 300 A EUR50
-1 X LIMIT SWITCH ROBOTRON 500V 6A IP 55 3.0 KW EUR6
-SWITCH-DISCONNECTOR SCHNEIDER INS250 100 3INTERPACK WITH
Vendedor: MEDCO Congreß-und Handels GmbH Halle
Año de construcción: usado
Ubicación: Land-please check the plaque for technical specifications.

if you need further information, please feel free to contact us via mail or phone. PLEASE CHECK THE PLAQUE FOR TECHNICAL SPECIFICATIONS. IF YOU NEED FURTHER INFORMATION, PLEASE FEEL FREE TO CONTACT US VIA MAIL OR PHONE.
Vendedor: Dimex Import Export
Año de construcción: usado
Ubicación: Land-2 generators biogas maritime container brand: deutz engine type: tbg 620 v16k year: 2000 / 2001 operating hours: ge 1 10,000 / ge 2 18,000 power: 2 x 1800 kva 2 schneider electric transformer 1500 kva 2 available aero   2 GENERATORS BIOGAS MARITIME CONTAINER BRAND: DEUTZ ENGINE TYPE: TBG 620 V16K YEAR: 2000 / 2001 OPERATING HOURS: GE 1 10,000 / GE 2 18,000 POWER: 2 X 1800 KVA 2 SCHNEIDER ELECTRIC TRANSFORMER 1500 KVA 2 AVAILABLE AERO
Vendedor: sasu zotoff
Año de construcción: usado
Ubicación: Land-please check the plaque for technical specifications.

if you need further information, please feel free to contact us via mail or phone. PLEASE CHECK THE PLAQUE FOR TECHNICAL SPECIFICATIONS. IF YOU NEED FURTHER INFORMATION, PLEASE FEEL FREE TO CONTACT US VIA MAIL OR PHONE.
Vendedor: Dimex Import Export
Usted no ha encontrado su máquina deseada? enviar consulta a todos los distribuidores (no hay registro necesario)