Manufacturer:
(Category: 1001)
One used good as new SCHNELL AUTOMATIC BAR SHAPING MACHINE BAR WISER 28 Bi-directional automatic bar shaping machine from bar, with 2 bending heads for the production of shaped wires and cut-to-size bars using wires up to Ø 28 mm (#8). Driven by digital electric servomotors. Bar Wiser 28 bar shaping machine is equipped with: - Max. pulling speed: 180 m/min (600 ft/min) - 2 bending units (upper and lower) - Clamp for extraction of the end part of the bar - Virtual mandrel - Web teleassistance
1 used concrete bucket, make summer - Built in 2020, but unused - Content: 1.5 cbm volume concrete measure = - Dimensions L: 2.10 m - W: 1.40 m - H: 1.85 m Outlet: = with vibrator on the hose outlet nozzle ... more information
automatic lattice girders, Fabr. ECG for standard and special carriers = for the production of standard and special carriers of medium to small series. - Length of beams: min. 0.8 to max. 16.0 m - Width of beams: 70 - 116 mm - Height of the beams min. 70- max. 400 mm ... more information
Steel mould for the production of 2 concrete steps each with nominal lengths of 90cm, 100cm, 110cm and 120cm. The mould has appropriate fittings and pressure plates and must be rebuilt accordingly for each step length. Step height 18cm, tread approx. 27cm. The mould was used on a concrete block machine type Schlosser SV40.
1 Gebr. Column formwork - Twin formwork - Length of formwork 16 m - max. chamber dimension 1.00 x 1.00 m - Steel formwork - incl. 10 vibrators - incl. converter - incl. control system Formwork is hydraulically movable ... more information
1 Gebr. Twin, column and truss formwork Formwork length: 25,000 mm max. concrete part basic height: 1,100 mm max. extension height: 2,000 mm min. concrete part width: 200 mm max. concrete part width, one-sided: 800 mm max. concrete section width, opposite: 600 mm ... more information
1 Gebr. hydraulic tilting table - Dimensions: 16.30 x 3.50 m - Single-sided upstand: 30 cm - height of the table. 85 cm - Steel flooring - the table needs to be reground - without vibrator, but with holding brachets with 3 hydraulic rams ... more information
2 Gebr. Variotop stair formwork for the upside down production of straight prefabricated stairs - Stair formwork type 18/150, consisting of base grate with tilting trestles and shoring - Mechanically centrally adjustable step body with swivelling steps -Integrated hydraulic control unit for the tipping process - Height-adjustable longitudinal parking on one side - Hydraulic control unit for the tipping process - Stairs are concreted overhead - max. 18 steps - Max. nominal width of the steps is 1.50 m - Tread range 250- 310 mm
2 Gebr. Hydraulic Tilting Tables Dimensions table 1 : 14.50 x 4.50 m Dimensions table 2 : 14.00 x 4.20 m with holding bras for vibrators with 2 hydraulic rams. ... more information
Precast concrete plant Complete with mixer & mixer. Machines Manufacturer: FIBO With approx. 40 tables 5500 x 3200 mm 6500 x 3200 mm 7500 x 3200 mm Not yet dismantled. Location Lower Saxony Net/export price 290.000,-- Euro I offer as an intermediary on behalf of the owner. The information is non-binding, prior sale is reserved. The offer prices are net and negotiable! Dismantling, loading and shipping on request! I will be happy to answer any further questions you may have. Goldman +49 173 6242 600 (also WhatsApp)
Used Floor Paver Manufacturer: Zenith Type: 913 Year of construction: 1978 Used traveller for concrete blocks, pavers Manufacturer: Zenith Type: 913 Year: 1978 ... more information
Hydraulically operated tilting vibration table for products up to 5 m. long. Type v20 vibrators max speed 6000rpm. Hydraulically operated beltfeeder. Hydraulically power packs. Pneumatically operated gates. PLC control system with monitor and memory for 100 different mould settings. Demoulding crane. Transport system consist of 2 lanes and 10 units of chain stands. PLC control system 70 steel pallets for a product area of 5000 x 1,125 mm and a load of 3500 kg. Amexpo Consult Merkurvej 31, 9370 Hals Denmark Mobile: +45 25291017.
Complete plant for the production of L bricks and wall panelsMould list : 7 pieces of wall panel formwork 12 cm Pos. 1 Masonry panel formwork 550 / 800 x 490 mm Number of wall panels : 12 pieces 550 x 490 mm 12 pieces 550 x 490 mm Pos. 2 Masonry panel formwork 550 x 990 mm Number of wall panels : 16 pieces 550 x 990 mm Pos. 3 Masonry panel formwork 800 x 990 mm Number of wall panels : 16 pieces 800 x 990 mm Pos. 4 Masonry panel formwork 1050 x 990 mm Number of wall panels : 16 pieces 1050 x 990 mm Pos. 5 Masonry panel formwork 1300 / 1550 x 990 mm Number of wall panels : 8 pieces 1300 x 990 mm 8 pieces 1550 x 990 mm Pos. 6 Masonry panel formwork 1050 / 1300 x 490 mm Number of wall panels : 8 pieces 1050 x 490 mm ...
Complete production for filigree top (swinging hammer), consisting of: 2 production lanes à 60 m, production width 2.50 m, with lattice cutting system, Concrete spreaders, plotters, lifting beams ... more information
1 Gebr. Rotor straightening system with double bending device (cranks) Directional extension 14 m = incl. 10 order picking trolleys incl. 5 wire drains Diameter 8- 16 mm The plant is BJ 2000 became General in 2009 overhauled at EVG In March 2022, a new PC was installed. The system works from left to right
1 Gebr. Ironing machine, - from 6-12 mm, - incl. 4 coils, - year of construction 2005, The system is in use in a production ceiling plant and is in a well-maintained, ready-to-use condition. ... more information
Fully automatic production line for concrete pipes DN300 up to DN1200 based on RADIAL PRESS or PACKERHEAD Technology. BFS-Souveraen Type: 1230 Condition: Very good The SOUVERAEN is the BFS pipe machine for high-performance production with first-class product quality. The counter-rotating pressing tool takes over the concrete compaction and is controlled by a sophisticated control system. The feeding of the concrete will be torque controlled, instead of concrete weight in standard systems. So the compaction quality is always secured. Production of concrete pipes according to all international standards. Year of construction: 2003, but has few hours, since it has worked very little since 2018 Location: Italy Condition: is in very good shape and well maintained. The machine is based on the packerhead technology (radial press) from BFS. The automatic handling is an open flo ...
Pallets Carousel for Double Wall (Twin Wall) and Filigree Floor Production, MFA M24514 Manufacturer: Vollert, Nuspl, Weckenmann, EBAWE, Filzmoser, RATEC, Unitechnik, SAA Year of construction: 2020, 2019, 2017, 2003, 1991 Control system : Siemens S7, Unitechnik Products: Twin Walls (max. height 3.0m), Filigree Floor Slabs PALLET CIRCULATION Pallets: 10.60m x 3.08m, 48 pieces STRIPPING AND LIFTING Hydraulic tilting station (EBAWE company, renewed in 2017) Lifting device for shell 1 + floor element (Weckenmann) CLEANING, PLOTTING, ROBOT-SHUTTERING AND OILING Automatic pallet cleaner, plotter, shuttering robot (Weckenmann, renewed in 2020 and 2003) STEEL REINFORCEMENT, ROBOT, WIRES, FILIGREE GIRDERS Automatic longitudinal and cross wire machine, diameter 6-14 mm, lattice girder preparation, Automatic insertion robot for laying all bars, as well as the lattice girders ...
For Sale is a ACOTEC Production Line Manufacturer: ELEMATIC Output: 160 m2/h (double line) Year: 2019 This offer comprises 2 ELEMATIC production lines with a combined capacity of 160m2/h and also includes a FRUMECAR batching plant. Acotec panels are precast, non-load bearing partition walls. They are room-high and 600-mm wide, with a tongue and groove design along the vertical edge. The panels are 6 times faster to install than traditional brickwork and twice as fast as blockwork. Modules list of the production plant -Concrete Supply -Plate Handler -Plate Feeding Conveyor -Casting Module -Product Module 6/100 -Saw -Conveyor for Saw -Trimmer -Product Conveyor -Recycling -Stacker -Stack Conveyor -Stack Return Conveyor -Crossing Station -Restacker -Product Tilting Receiver Conveyor -Product Tilting Device -B-Quality Conveyor -Pallet Conveyor -Cleaning ...
Complete packaging machine line (used) with 6 psotions Cover sheet support, horizontal strapping, vertical strapping, film winder, shrink frame, sealing head (reserve) ... more information