Manufacturer:
(Category: 1002)
ID2927 Complete limestone processing plant Complete limestone processing plant consisting of: • pre-crushing plant – approx. Year of construction 1970 • Primary crusher impact mill Hazemag AP5, capacity up to 500 t/h • Secondary crusher impact mill Hazemag AP4 – approx. year of construction 1970 • Gravel plant 300-350 t/h – year approx. 1983 • Fine crusher impact crusher SBM 10/6/4 EXP – year 1993 • Fine chippings plant 350 t/h – year 1996 • with feed hopper, pusher truck feeder, roller grates, silos, screening plants, conveyor belts, dedusting, etc. • Control new in 2018, loading control new in 2020 Complete limestone processing consisting of: • Pre-crushing plant - approx. built in 1970 • Hazemag AP5 primary crusher impact mill, capacity up to 500 t/h • Secondary crusher impact mill Hazemag AP4 – approx. built in 1970 • Ballast mill ...
ID2955 Key Maker Magic 1211 year/Year of construction 1984 Manhole finisher, 1 piece Magic 1211, with 2 Atlas 300 + 400 molds, 2 palisade molds, 1 built-in mold, 1 vibrator incl. FU, various base sleeves Shaft paver, 1 piece Magic 1211, with 2 pieces of moulds Atlas 300 + 400, 2 pieces of mould palisades, 1 piece of mould installed, 1 piece of vibrator incl. FU, various lower sleeves
Ground paver Knauer TYPE Komet 104 C built in 1980. Manual machine for small quantities or trial productions. Stone height maximum 50 cm For hollow blocks, chimney blocks, lightweight concrete blocks, etc. Very robust machine, with manual hydraulic control. The electrics are very simple and easy to repair. The machine is ready for operation and was still used for special stones until the introduction of a new fully automatic machine. It is well maintained. However, all guides and drives are in order and well lubricated. Without mold shaker and mold, these are in the photo, but are not included. Spare parts are also still available and could be purchased at the time of sale.
Used sand-lime brick press, hydraulically working, two-sided compaction, 195 kW install. Power, control S5, max. pressing force approx. 10,000 kN, max. pellet height 650 mm, for the production of sand-lime brick blocks and elements, fully automatic operation, plant still in operation – visit possible
Sand-lime brick press, hydraulically working, Fabr. Dorstener HDP800 N (left-hand version), with two-sided compression, 190 kW install. Power, control S5, max. pressing force approx. 6,000 kN, max. pellet height 300 mm, for the production of sand-lime brick blocks, fully automatic operation, system is dismantled and stored in a dry place
Landfill conveyor belt 650 x 23 m galvanized, with supports, walkway, hinge cover Good condition Also available and mounted ... more information
IFE Circular Vibrating Screening Machine Screen width 2 m Screen length 5 m 2 Decks Plastic exchange system WS 85 or similar Machine ran in limestone little wear and few hours With sieve funnel and stand-up feet ... more information
Slicer IFE 2 x 5 m 1 Deck Version Screen lining, wire cross-tensioned Very good condition, few operating hours from a pilot plant ... more information
2 PCs unused humidity probes for mixer Original spare parts for a love Mr of ZE 2000 ... more information
Impact crusher Pozzato 8-5-3 Machine width 500 mm Rotor diameter 800mm, 3 impact bars Capacity up to 40 t/h Feed size approx. 50 mm Sand content in the crushing product up to 50% Machine on base frame Older year of construction with very few operating hours ... more information
Split sieve coverings for an IFE dewatering screening machine 1 pcs L 500 mm x W 800 mm gap 0.3mm 1 pcs L 1000 mm x W 800mm gap 0.3 mm 2 pcs L1000mm x W 800 mm gap 0.3 mm 3 pcs L1000mm x W 800 mm gap 0.3 mm 5 pcs L1000mm x W 800 mm gap 0.3 mm The pads are unused or only in use for a short time
Drum screening machine for the production of humus or similar Wheel Loader Feed Hopper Ascending band Drum sieve with brush approx. 1.x4m ... more information
2 cyclones as good as new Type AKA VORTEX Twin TRT 4118 Throughput per twin 95m3/h total 190m3/h Diameter 200mm, cutting cut approx. 50my 1 pcs new cyclone Type AKA Vortex KRS3128 II 40m3/h DM 150 mm All cyclones including overflow line and shut-off valve If required, a refurbished PUMP METSO VASA is also available Drive 30 kW available are also handed in individually
Flender drive gearbox from a tunnelling conveyor belt mill Gearbox, output speed approx. 44 rpm (1.5 m/s with drum diameter 630mm) Drive motor 75 kW Turbo clutch ... more information
Conveyor belt tensioning drum with shaft Diameter 830mm Drum width 1300 mm for conveyor belt 1200 mm ... more information
Dosing conveyor belt Belt width 500 mm Wheelbase 2500mm Drum diameter 220mm Drive drive drive north 1.1 kW, 0.12 m/s Spindle clamping device Strap EP250 3 3+2 galvanized version Leitgosse Intrusion protection Ripcord switch ... more information
Pre-breaker with crusher Suitable for soft lime, marl, coal Power up to 200- 600 t/h Task size up to 1500mm Drive - electric transformer station 30kV/400V Drive power approx. 500 kVA Plant weight approx. 130 tons Task bunker 25m3 Chain conveyor Roller rust Schlagwalzenbecher Deduction tape Dust removal system Caterpillar suspension - not self-driving Conveyor belt 3 x 40m Telestack, self-driving, belt width 1200mm Immediately available
Compact filter plant McCloskey new! Screening plant for the GALA of construction, agriculture Mobile system area ca 2 m2 2 screen decks ... more information
Inlet: 1,440 x 900 mm Rotor diameter x width: 1,250 x 1,420 mm new wear lining ... more information
Autoclaved Aerated Concrete AAC Production Line, Porenbetonwerk, Aerated concrete plant, ERICH PETER MACHINES-PLANTS GMBH A-7083 Purbach Hofgartengasse 7 Phone: +43 664 3358378 Mail: office@machines-plants.at Web: www.machines-plants.at ... more information