subcategorias
(terceiro nível de categoria)
Fabricante:
(Categoria: 107)
Hydraulic press brake 160t / 3200mm with controller E21 (automatic adjustment of the back stops). The status of the new machine Year 2016 ... mais informação
The line has undergone commissioning and is in good condition. Not used. It is under conservation. Rod diameter from 5mm to 12mm; Mesh width 800mm-2500mm; The pitch between the axes of the transverse rods (multiples of 50mm) is from 50mm to 300mm; The pitch between the longitudinal bars is from 100mm to 300mm; Welding speed of cross bars is 55-80 cycles/min. n Line composition: Main machine - 1 piece; Chiller - 1 piece; Compressor - 1 pc.; Dryer - 1 pc.; Receiver 1000 liters - 1 piece; Operator control panel (in Russian) - 1 pc. Optional equipment: The machine cuts correctly. Rod diameter from 5mm to 12mm; The length of the rods is 6 m; Speed 130m/mi. Specifications Power supply: alternating three-phase current 380V 50 Hz; Cascade welding mode; Transformer power 150 kW - 12sh; Peak power 315-630 kW; Nominal pressure, air flow 06.-10.0MPA, 130m3; Supply voltage 3 p ...
The machine is in good technical condition. Max. length of cut sheet: 4000mm Max. thickness of the cut sheet: 6 mm. Upon prior agreement, the possibility of inspection in progress. ... mais informação
4-roll Hydraulic plate bender 8000 x 40 mm. 1960 Froriep 8000Х40 mm Plate rolling machine - 4 rolls 8000Х40 mm ... mais informação
We sell Turret punch press - MP10-30 used, 2007, manufacturer JIANGSU YANGLI GROUP CO. Possible leasing, rent-to-own. They are also interested in intermediaries with a place to store equipment (they are ready to pay for rent). MP10 CNC series punching machine has a body structure (ZL2004 2 0108852.4), which adopts tempering treatment. German I + L. The hydraulic system has reliable performance and low power consumption (1 1 kW). FANUC CNC system OIS or SIEMENS 840D is used on this punch series. The revolving type (ZL 022 1821 1.X) features a long sleeve structure and the station index has a sectional wheel and a worm gear.
Valley. Crank shears with an inclined blade for a sheet of 20x2000 mm, model NLZ427B, are designed for cutting sheet metal with a thickness of up to 20 mm and a tensile strength of S 500 MPa. Scissors can be used in the procurement workshops of metal structures, machine-building enterprises, repair and other plants, when used in climatic zones with a temperate and cold climate version UHL, dry and humid tropical - version O; placement category 4 according to GOST 15150 - 69 The lower value of the air temperature must be at least +5 0С. Designed for cutting metal up to 20mm thick 1. Maximum cutting force, kN 1000 2. The largest dimensions of the metal being cut with temporary 3. resistance
Type: CTO 80/2500 Parameters: 80 t, 2500 mm Manufacturer: Strojárně Piesok Year of production / SO / GO: - / - / - Description: The machine is in good technical condition. Nominal forming force: 80t Working table length: 2500mm Maximum stroke: 150mm Maximum distance of the table from the ram: 360mm Working height: 800mm Dimensions LxWxH: 3700 x 1250 x 2385mm Machine weight: 6550kg Upon agreement, the possibility of a tour in progress.
The machine is in good technical condition. Max. length of cut sheet: 2000mm Max. thickness of the cut sheet: 6.3 Weight: 6725 kg Upon prior agreement, the possibility of a tour in progress. ... mais informação
machine for marking and cutting rolled metal - corner TBL 2020 Production China. There are all documents. The machine was not in use, but stood for 2.5 years without observing the storage conditions, so the computer (system unit) does not work. Everything else is normal. We are ready to present the machine for inspection at any time. The machine is currently stored in a warehouse in the Republic of Tatarstan.
I offer hydraulic shears not sheet metal marked NTA 3150/10A manufacturer Strojáreň Piesok. The maximum cutting length is therefore 3150 mm and the strength of the structural steel sheet is 10 mm. Plugged in, fully functional, but so rarely used that its not worth my while to keep them. (they do not fit into our primary production segment) Price negotiable, buyer arranges transport, total weight 14,000 kg Possibility of viewing, testing - at the Chrudim facility
Laser power: 3.200 W Type of input current: three-phase Aluminium sheet thickness (max.): 8 mm Working range: 3,000 mm Total height: 220 cm Workpiece weight (max.): 710 kg Sheet thickness steel (max.): 20 mm Total weight: 12,500 kg Input power: 73 kW (99.25 hp) Sheet thickness (max.): 20 mm Traverse path X-axis: 3,000 mm Traverse path Y-axis: 1,500 mm Space requirement width: 9,300 mm Space requirement length: 4,600 mm Space requirement height: 2,200 mm Input frequency: 50 Hz Year of last overhaul: 2014 Feed speed X-axis: 60 mm/min Feed speed Y-axis: 60 mm/min Laser shaft length: 10,600 Nm Equipment: Documentation/manual, safety light barrier Very well maintained Trumpf TruLaser 3030 in very good condition. It has no damage and is ready for immediate use. It is currently still being worked on and can therefore be inspected in operation. Tra ...
LINE FOR LOWER AND CROSS-CUTTING OF COILS (annual capacity 10 000 t): Sheet thickness: from 0.4 mm to 2.0 mm Sheet width: from 800 mm to 1580 mm Material: cold rolled and galvanized sheet metal Strength limit: max. 480 MPa (for max. thickness of 1.5 mm) Yield strength: max. 250 MPa (for max. thickness of 1.5 mm) Output material parameters - cut sheets Width tolerance up to: +/- 0.1 mm according to EN 10140 Length tolerance up to: +/- 0.3 mm according to EN 10140 Maximum number of longitudinal stripes: 6 (for max. thickness 1.5 mm) Maximum number of longitudinal sections: 5 (for max. thickness 1.5 mm) Minimum width of one strip: 180 mm Minimum length of boards: 200 mm Maximum length of the boards: 3500 mm +
BREAKING FORCE: 196 KN MAX SHEET THICKNESS: 3 MM X-AXIS MOVEMENT: 2500 MM Y AXIS MOVEMENT: 1270 MM NUMBER OF INDICATORS: 2 NUMBER OF POSITIONS: 31 STEEL: 3 MM STAINLESS STEEL: 2 MM ALUMINUM: 2 MM MAIN ELECTRICAL CONNECTION: 400V USED POWER: 24 KVA WIDTH MEASUREMENTS: 5330 MM DEPTH MEASUREMENTS: 5123 MM HEIGHT MEASUREMENTS: 2160 WEIGHT OF THE MACHINE: 11000 KG A copy of the software.
Automatic line for the production of sandwich panels of the LL-2000 brand of the P-SYSTEMS plant (Czech Republic), 2003. The line is designed for the production of wall and roof sandwich panels with mineral wool and polystyrene foam insulation. The manufacturing process is automatic. Requirements for raw materials for sandwich panel sheathing - thickness 0.4 ... 0.6 mm .: - sheet steel galvanized The production process is carried out automatically (with the exception of the laying of insulation and the preparatory process). Completeness of the line, technical characteristics: - Unwinding device - 2 pcs. - Profiling area. - Table for supplying insulation. - Glue application and distribution device. - Steel strip heating section. - Pressing device. - Transverse movable cutting device. - Line control system. Line productivity per shift (8 hours) 1000 sq.m. The maximum spe ...
Brand: Hermak Sheet Thickness: 0.3mm-3mm Roll Width: 500mm-1600mm Maximum Roll Weight: 20 tons Maximum Package Weight: 5 tons Maximum Package Length: 6 Meters ... mais informação
Rolling mills for cold rolling of sheets 2 types of LSTC profiles (C and U) + PIR profile panel. Documents with characteristics can be obtained as a file. to or email. ... mais informação
The machine is fully functional, with a rich set of tools. Pipe bending tools: fi 83 - R300 fi 88.9 - R300 fi 101.6 - R250, R400 fi108 - R450 fi 114.3 - R550 fi 133 - R400 fi 137 - R500 fi 168 - R700 fi 193 - R600 fi 219 - R640, R800 ... mais informação
Decoiler Coil weight: 2 x 2 ton Material width: 380 - 500 mm Coil exterior diameter: 1.300 - 1.400 mm Expansion range: 445 -530 mm Leveller / Straightener Material width : 40 - 500 mm Number of levelling rolls: 7 pcs. Diameter of the levelling rolls: 60 mm Number of pinch rolls: 2 pcs. Diameter of the drawing rolls: 60 mm Number of pull out rolls: 2 pcs. Diameter of the pull out rolls: 60 mm Material thickness: 0,4 - 1,6 mm Cross section: 800 sq mm Feeding speed: 0 - 30 m / min Required power: 3 kW
The MTM-KA1000 multi-electrode machine is designed for the production of masonry mesh from round bars straightened and cut to the required size. The length of the welded mesh can be any and depends only on the length of the longitudinal rods. The width of the welded mesh is 350mm -1000mm; The diameters of welded rods are 3mm -6 mm; Distances between the axes of the rods: transverse 50mm - 200mm; longitudinal 50,100,150,200mm; Rod material: low-carbon steel, smooth or BP; The number of welded transverse rods is 40 pcs/min; Rated voltage 3 ph. mains, 50 Hz, 380V; Maximum power consumption 75-100 kVA; Compressed air pressure in the network, MPa (kgf/cm2) 0.63 (~6.3); Free air flow 2 m3/min; Overall dimensions 1800x1800x1700 mm; Weight 2000 kg
Coil weight: 500 kg Material width: 41 mm Coil exterior diameter: 1.000 mm Expansion range: 250 - 500 mm Speed: 20 m / min Required power: 0,5 kW Dimensions L x W x H: 1.000 x 850 x 1.700 mm Weight of machine approx.: 200 kg ... mais informação