prensas usadas para la venta

Inv. Num. : 6700 Type: 3000 kN Producer: Loire Created: 1992 GO 2008 Parameters: Control system: SIEMENS SIMATIC OP17 Compressive force: 3000 kN Table length: 2495 mm Table width: 1505 mm Maximum distance between the table and the ram (when the ram is low): 1200 mm Stroke: 800 mm Working speed: 64 mm/s

Inv. Num. : 6701 Type: 4000 kN Producer: Hydraulico Created: 1977 Parameters: Control system: SIEMENS SIMATIC OP Compressive force: 4000 kN Stroke: 800 mm Table height: 680 mm  ... más información

Inv. Num. : 6050 Type: 30T Producer: MEYER Produced: 1982 Parameters: Compressive force: 30 t Distance between frame walls: 300 mm Lifting height: 200 mm  ... más información

Inv. Num. : 6606 Type: LDC 250 Producer: SMERAL Created: 1980 Parameters: Compressive force: 250 t Maximum stroke rate upper table: 38 1/min Ram stroke: 200 mm Adjustment of the plunger: 120 mm  ... más información

Inv. Num. : 6612 Type: Trumatic 500 Producer: Trumpf Created: 1955 Parameters: Operating hours: 69739 h Compressive force: 220 kN Maximum length of the sheet plate: 2500 mm Maximum blade width: 1250 mm Machine weight: 11050 kg 4 cassettes for a single tool and a cassette for a 6-way multitool

Inv. Num. : 6443 Type: TECHNICA PLUS Producer: DERATECH Created: 2009 Parameters: Control system: Cybelec DNC 880 S Operating hours: 3040 h Compressive force: 250 t Maximum bending length: 4100 mm Total power requirement: 18.5 kW Machine weight: 18000 kg Equipment: Tools 2-axis backgauge

Inv. Num. : 5831 Type: PKnT 160 Producer: ERFURT Created: 1987 Parameters: Compressive force: 160 t Maximum stroke rate top table: 15 1/min Total power requirement: 21 kW Ram stroke: 265-425 mm Adjusting the plunger: 130 mm  ... más información

Inv. Num. : 4164 Type: LKT 250 Producer: SMERAL Created: 1977 Parameters: Pressing force: 250 t Table: 1575 x 1150 mm plunger stroke: 250 mm Stroke: 20/min Plunger adjustment: 100 mm Installation height: 750 mm Shock dimensions: 1380 x 850 mm Motor power: 28 kW Dimensions 2800 x 1240 x 4450 mm Machine weight: 23400 kg

Catalog No. : 6536 Type: TRUMATIC 500 R Producer: Trumpf Made in: 2000 Characteristic: Hours on: 36200 h Pressing force: 220 kN Travel length X-axis: 2500 mm Travel length Y-axis: 1250 mm Machine weight: 11050 kg Equipment: Tool Cartridges (2x) USB Interface  ... más información

Inv. Num. : 5451 Type: 1250 F1 Producer: SIMASV Created: 2011 Parameters: Compressive force: 30 t Maximum sheet thickness: 6.3 mm Maximum punching speed: 450 1/min Punching diameter: 89 mm Machine height: 2400 mm Machine length: 4200 mm Machine width: 3700 mm Machine weight: 5500 kg

Inv. Num. : 5698 Type: LKT 250 Producer: METALPRESS Created: 1974, GO 2002 Parameters: Compressive force: 250 t Table length: 1150 mm Top table width: 1580 mm Maximum stroke rate top table: 7-25 1/min Ram stroke: 250 mm Adjusting the plunger: 100 mm Machine weight: 22950 kg GO 2002: converted to hydraulic clutch electronic control

Type 5 Nominal weight of falling parts 1750 kg Impact energy, not less than 4878kgm Number of strokes per minute 85 Max. ram stroke 890mm Diameter of ram 455mm Ram pallet face 405x305mm Anvil pallet face from floor 535mm Height above floor 4040mm Baseplate 4405x2085mm Motor rating 110 kW Weight 40000kg Weight without anvil block 25000kg

Air forging hammer Stanko MB 4134 Year of manufacture: 1988 Nominal weight of falling parts, kg: 250 Energy of impact, Kj: 5,6 The greatest number of impacts in a minute: 150 Ram axis-to-frame distance, mm: 420 Working zone daylight, mm: 450 Die impression size, mm: 510 x 80 Main electric motor power kW: 22 Weight of a hammer with an anvil-block, kg: 7850 Price 6500 EUR

Manufacturer: AIDA ENGINEERING LTD. Made in: Japan Presses are never used, condition is like new. Feeders and straighteners are available. Capacity: 80 tons Rated tonnage point: 6,5 mm Stroke: 200 mm Number of strokes per minute: 60-150 Bolster area (left-to-right x front-to-back): 1400 x 500 mm Slide area (left-to-right x front-to-back): 1400 x 500 mm Bolster thickness: 200 mm Distance between slide and bolster: 450 mm Slide adjustment: 50 mm Main motor: 45 kW Required air pressure: 5 kgf/cm² Total weight: 33 tons Roll feed Material width: 70=300 mm Material thickness: 0,25-0,4 mm Feed length: 50-120 mm Feed angle: 300-60 deg Uncoiler Coil diameter: 800-1200 mm

Cold stamping press Stanko P 0443 Capacity, tons: 2000 Nominal liquid pressure, kg/cm²: 320 Table size, mm: 1000 x 1000 Table stroke, mm: 500 Table speed, mm/s: 0,14 Rapid table speed, mm/s: 3,1 Distance between columns, mm: 1090 Shut height, mm: 800 Hydraulic drive motor, kW: 5,5 Voltage, V: 380 Frequency, Hz: 50 Press dimensions, mm: 2575 x 1500 x 3285 Press weight, kg: 27000 Price 21500 EUR

High Speed Precision Press Maker Obata (Japan) Year of manufacturing - 1981 Capacity 10 t Stroke length 22 mm Speed 100-400 stroke/min price 6000 EUR  ... más información

Minster HB2 Punching Press equipped with sound cabin, Kohler decoiler, load/unload crane and service crane. Price and other information about the machine available on request. For those interested, I will send a link to more pictures. Specification: Punching press Manufacturer – Minster USA model – HB2 (Hummingbird) serial no – 25007 die table dimensions – 914.4mm x 635mm year of manuf. - 1981 pressure 60 t type - Flywheel stroke of slide - 25.4 mm no. of strokes - 200 - 1600 /min shut height – bolster – 366.6 mm; bed – 443 mm power requirement - 50,0 kW dimensions of the press ca. 2,7 x 1,7 x 3,6 m Decoiler Manufacturer – Kohler type – 18260-1500.2 year of manuf. - 1981 material width 260mm coil weight - 2 x 1,65t material thickness - 0,4 - 3,0mm coil internal diameter - 460 - 530mm coil external diameter - max 1350mm no. of stra ...

SLAVES mod- STP C 204 of 200 tons. - 4 meters  ... más información

Hämmerle AP175-3100 - Hydraulic press brake - Control: Cybelec DNC 7400 (overhauled & new display) - Controlled axes: Y1, Y2, X, R - Stop finger can be moved manually - Machine not fully functional (error in tool clamping) - Year of construction 1985 Specification - Max. pressing force: 1750 kN - Max. working length: 3100 mm - Max. stroke: 265 mm - Projection: 300 mm - Operating voltage: 400 V - Dimensions WxHxD: approx. 4300 x 3300 x 2650 mm - Weight: 16100 kg

Used Feintool HFA 4000 equipped with Feeder Line Saronni total force 2500-4000 kN blank holder force 200-2000 kN back pressure force 100-1000 kN shearing force 1000-3700 kN safety distance 14 mm FEEDER LINE brand SARONNI year 2006 - completely overhauled in 2012  ... más información