Fabricante:
(Categoría: 307)
1 x Farrel Banbury internal Mixer, Model 00C. Machine number: 91M7017, Year: 1992, Stainless steel jacketed swing side (drop door design). Maximum steam or water pressure 150psi, chrome plated two wing cored rotors with spherical roller bearings, gross capacity of mixing chamber 4.24 liters. 5" Diameter ram cylinder, maximum pressure 100psi. Chrome plated single slope V-bottom, stainless steel, pneumatically operated front door, F.Y.A. dust stops, oil seals, oil injector, thermocouple. With 65kw (87hp), 340/440 volt, 1500 rpm motor, reducer ratio 15:1. Unit mounted in an enclosed cabinet with a pull-out discharge drawer. Includes an operator panel. In good condition.
1 x Francis Shaw 45mm dia coldfeed rubber extruder, M/c no. 4513, Year: 1992, power roll feed, L/D ratio 15:1, hinged straight head with c\clamp, cored scred + jacketed barrel with built in temp control unit. Complete with control panel and in very good condition. Box of dies included. ... más información
1 x Alpha Technologies Mooney MV2000e Viscometer software discs and operation manual are included. You will have to register the software. PC not available. In good condition. ... más información
clamping force: 800 kNinjection volume: 78 cm³screw diameter: 25 mmplaten size: 570 x 552 mmCondition: used,Specification: injection moulding machine for LSR - used Nr. 13EN08clamping unit:- clamping force: 800 kN- size of heating platen: 570 x 552 mm- Between tie bars horizontally: 405 mm- Between tie bars vertically: 345 mm- Opening stroke: 310 mm- Ejector force: 25.4 kN- Ejector stroke: 100 mm- Mould installation height max.: 530 mm- Mould installation height min.: 250 mm- Bar diameter: 60 mm- Control: CC 90-A0Injection unit:- Injection volume max.: 78 cm³- Injection weight max.: 90 g- Screw diameter: 25 mm- Metering stroke: 160 mm- Screw speed max.: 20 - 400 rpm- Injection flow: 87 g/sec- Injection flow (increased): 64 g/sec- Sp ...
Francis Shaw 30mm Extruder Roller Feed LD ratio 15:1 Year 1993 ... más información
Kobelco Twin Screw Roller Head Extruder (horizontal type), Model TSR-330 Roller die assembly (TSR-33H005H) 38in wide x 16in dia Roller die moves away from the extruder/mixer section via hydraulic ram. driven by 102kW DC variable speed motor through Hansen reduction gearbox (on flexible coupling so roller die can move forwards/back). Twin screw dump extruder 330mm screw dia driven by 90kW DC variable speed motor through Hanson reduction gearbox. In very good condition. Previously running underneath an F270 Banbury. Complete with all controls, manuals and documentation etc.
1 x Francis Shaw model K2A MK4 Intermix Machine number 11242.8, Year June 1994, NR2 rotors, Working batch volume 27 - 36 litres Drop door with linear actuator, SSA dust seals, Pneumatic hopper, Hansen semi unidrive gearbox, Rating 150kw, 1475/32rpm, With ASEA 152kW, 1510rpm DC variable speed motor and controls.
Iddon HRX 4.5? (120mm) Cold Feed Rubber Extruder Year 1994 LD ratio 17:1 Bostock & Bramley Gearbox ABB Motor: 1994, 95kW, 1870 rpm, 419 amps, 360 volts With 1 x spare vacuum screw With Control Panel ... más información
roll diameter: 560 mmroll length: 1500 mmrolls drilled: Peripher Nip adjustment: hyraulisch 0total power requirement: 150 kWCondition: used, completely overhauled, with warrantySpecification: rolling mill 560 x 1500 mm - used model external gearbox - motor sideways placed at the machine- roll diameter: 560 mm- roll length: 1500 mm- model: Duplocom / pluridrive- Peripherally drilled rollers for water cooling- Cardan joints between gearbox and rollers- Individual drive for the rollers, for variable friction- hydr. gap adjustment- Hydraulic unit- Tilting steel guide plates- rollers mounted on roller bearings with appropriate lubrication- rollers with new ball bearing slewing rings, make Maier, for the connection to the water circuit- One gearbox- two individual drives, each with: 2x 75 kW - 400 V - 50 ...
available Triplex Extruder- Cold Feed with head and feeder. Description attached! ... más información
Choice of 3 x RENTEC n.v. (Belgium) steam heated autoclaves Internal dimensions: 3000mm dia x approx 2500mm long (inc. dished end and door), Working pressure 10 Bar, Hydraulic Bayonet type door Year of manufacture 1995 Drawings and documentation available. No controls or hydraulic unit for door (all 3 were running off 1 pump). In very good condition.
clamping force: 350 kNinjection volume: 59 cm³screw diameter: 25 mmplaten size: 400 x 400 mmCondition: used,Specification: injection moulding machine for rubber - used International size: 350-90 clamping unit:- clamping force: 350 kN- clamping platen size: 400 x 400 mm- Clear distance between tie bars: 270 x 270 mm- Mould installation height min.: 225 mm- Distance between clamping platens: max. 550 mm- Opening stroke max.: 325 mm- Ejector stroke: 125 mmInjection unit:- Screw diameter: 25 mm x 20D- Injection volume max.: 49 cm³- Injection part weight: 59 g/hp- Max. injection pressure: 1,860 bar- Screw circumferential speed: 37 m/min- Cylinder heating: 4x 900 W- Nozzle heating: ...
Qty 1 x Pomini Model P270 Banbury internal mixer, M/c no. 362, Year: 1996, HDM style rotors (2 wing equivalent), PYH Dust stops, Hydraulic drop door discharge with Linear actuator, Vickers hydraulic power pack, Unidrive gearbox with couplings (11D type, 1000HP rating). Pneumatic hopper. Without motor or controls. Can be supplied with or without gearbox. Quote for new motor and controls on request.
1 x Wickert 500ton upstroke vacuum press, Type: WKP5000/5/3, Year of manufacture: 1997, Machine Number: 2885 with 500mm x 500mm electrically heated platens, sliding bottom platen with ejector table, Daylight: 340mm 400/690V, 50Hz, 22kW. Heaters 12.5kW, Pressure 300 Bar Fixed guarding to rear, SICK light curtain guards to the front. With Siemens S5 PLC controls. In very good condition.
Farrel Twin Screw / Rollerdie Extruder complete available with Motor and Inverter Description attached! ... más información
Press (n°1) Upstroking Manufacturer: Agila Closing force: 850 Ton Year 1997 hydraulic Steam Platens : 3 2 cavities (250 mm opening) Size heating platens: 1100 x 1400 x 76 mm Diam. piston 650 mm Hydraulic pressure: max. 250 BAR Hydraulic tank: 500 L Complete manual included Size press 2400 x 1400 x 4200 mm (LWH) Weight +/- 23.000 kg
machine measurements: 1500 x 2400 x 1150 mmmachine weight: -- kgpower capacity: 12 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
Type; AUMA 15SN X 1600 Manufacturer: Berstorff, Germany Year of manufacture: 1998 Technical Specification: Working width: 1600 mm Steel belt width: 1750 mm Steel belt thickness: 1,8 mm Steel belt length: 15600 mm Rolls width: 1950 mm Center distance between frames: 2330 mm Heating roll diameter: 1500 mm Stretch rolls (I, II, III) diameter - 1000 mm Vulcanizing time: 1?30 min Working speed: 7?.210 m/h Max steam pressure in heating roll: 13 bar Max steam pressure in lower stretch roll: 8 bar Surface temperature of: Heating roll: ca. 195oC Lower stretch roll: ca. 175oC Pressure in heating zone between steel belt and rubber: 60 N/cm2 Main motor speed: 1 450 min-1 Drive position: Left from inlet Paint: RAL 6011 Air supply: 6 bar Cooling water supply: + 25oC Max hydraulic pressure Belt pressure tension: 250 bar Belt pressure regulation: ...
1 x Farrel model F270 Banbury internal mixer, Machine number: 98M5007, Year July 1998, 270 litre capacity, 2 wing rotor design, FYH type dust seals, Hydraulic drop door with linear actuator, Process oil system, Pneumatic hopper. with David Brown unidrive gearbox, serial no GS50277, Leroy Somer Type LSM54 L76P 1492kW AC motor, Dec 2001, RPM 1000/1200, 750V (includes 11kv > 750v transformer). Output rpm 49.8/43. Alstom \Syncdrive\ AC variable speed drive controller, 1940 KVA, 750V, digital drive new in 2001. With Siemens S5 Control system. In feed conveyor and dust extraction system also for sale if required. Spare refurbished Leroy Somer motor also available. Complete and in good condition (still installed at a factory in UK).
1 x Francis Shaw model K7 MK5 intermix, Contract no. 1443, Date: 22.1.98 (year 1998), NR5 Rotors, Net chamber volume 310Litres, Batch size: 217kgs, Hydraulic drop door with linear actuator, Hydraulic hopper, Francis Shaw Unidrive gearbox: Order no. G590304, KW rating 1300, output 46.45 rpm, ratio 25.834/1, 2 x 700kW, 1250rpm DC motors, 3ph, 660V, 50Hz. The mixer is in serviceable condition, but is without electrical drives/operator controls, hydraulic unit or lubrication unit (Can all be quoted if required). Full manuals/drawings available. Available: Immediately (ex stock UK).