Fabricante:
(Categoría: 307)
machine measurements: -- mmmachine weight: -- kgpower capacity: -- kWCondition: usedSpecification: dosing unit type SiloStar 922 A - second-hand- for dosing liquid silicone LS- container: 20 litre hobbocks and 200 litre drums- Power connection: 400V, 50Hz Equipment of the plant with:- Fardoser SPS P1- Mixer / material pressure regulator cooled with outlet valve- roll-in device- Pressure and material shortage protection- Machine connection outlet valve and pressure regulator- Pressure vessel ColourThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
LWB Steinl Injection Machine Type VCE -T 500/160 T Clamp power 500 KN Injection volume 160 cm3 Year 2006 6 Bar 400 v 50 hz 26 KW ... más información
LWB Steinl Injection Moulding Machine Model VCE-T-TPE-EPDM 100 ton capacity ECO touch screen control ... más información
Berstorff Strainer Extrusion Line Consisting of: Extruder Supplier Berstorff Type GE 150KSx16D Year of construction 2007 Pins: 12 Pins per level: 8 Condition: good Weight approx. 10000 kg Screen change: hydraulic, bladder accumulator 20lt / 300Bar D = 200mm Gear pump Supplier: Maag Pump Systems Type: extrex® 110-5 RV Volume 716 cm³ / rev Year of construction 2013 Condition: good Heaters Supplier: Regloplas Type P140 Year of construction various Number 5 pcs. Cooling bath Cooling medium Water above, 2 rows below with 4 fans each Year of construction 2006 Condition: good Dimensions 9m Weight approx. 500 kg Especially 8 fans Installation tape Year of construction 2006 Condition: good Weight about 300 kg
1 x Buzuluk 240 litre Internal mixer Model: 14630, year: Dec 2008 (body and hopper), Batch size: 200 kgs, Drilled sides, Self sealing type dust seals, Oil injection, Hydraulic drop door with linear actuator and toggle latch, Stellite faced drop door, Two wing tangential rotors. 20in pneumatic hopper. 3 zone TCU Full unidrive gearbox (Make Skoda), with 630kW, 6000V, 739rpm, 73.5A slip ring motor and Oil filled starter. In very good condition.
Machine number 185386/2008 ... más información
Prodicon Batch Off Unit 500mm sheet width Inlet speed 0-10m/minute Sheet thickness 5-12mm No. of cooling sections 3 No. of fans 9 Complete with electrical control panel. Year 2009 ... más información
Berstorff Three Roll Calender Manufacturer: Krauss Maffei Berstorff 2650mm wide x 650mm (26”) diam. Effective working width 2600mm (Roller Head Die Width) Rolls Configuration: ‘I’ shape Rolls Type: Peripherally Drilled Drive: Right Hand Transmission: Direct Drive by Cardan Shafts Motors: 3X 75 KW, 2600 RPM, 50 Hz Nip Adjustment: Hydraulic (Berstorff patented) Fixed roll: Roll 2 (middle roll) Adjustable roll: Roll 1 and 3 (upper and lower roll), Max Roll gap is 80 mn Cross axis: Roll 1, 2 and 3, Hydraulic operated, max. 25 mm Pre-loading & Roll Bending: Available Rolls Speed: Variable, 0.5-10 m/ min Bearings: Antifriction Roller Bearings Electricals/ Controls: PLC Complete with motor and controls Year 2009
1 x Farrel F370 mixer chamber and hopper M/c no. 081110, Date: November 2009, SSA dust stops, 4 Wing Rotors, Drop door with Linear actuator, Base Plate with Toggle Latch. Pneumatic hopper with extension neck (Floating weight looks to be in good condition). Parts available: Body, baseplate, Toggle Latch, actuator and Pneumatic hopper with extension neck.
Berstorff 6inch (150mm) Strainer Extruder Manufactured by: Krauss Maffei Berstorff Model: GE 150 K Screw Diameter: 6"/150 mm L/D Ratio: 6 Speed: Variable, up to 45 rpm Motor: 90 KW, 1500 RPM Transmission: Direct Drive, 3 steps reduction Gear Reduction Ratio: 33:1 Year 2009 ... más información
Berstorff 8inch (200mm) Cold Feed Pin Extruder Manufactured by: Krauss Maffei Berstorff Extruder Type: Vac GE 200 SC, Pin Type No of Pins: 2 X10 + 1X12 (Hydraulic adjustment) Screw Diameter: 8"/200 mm L/D ratio 18:1 Drive: 300 Kw, 1500 RPM Screw speed: 33pm Complete with Control Panel Roller Die Suitable for rubber compounds Year 2009
LWB Steinl Injection Machine Type VREFE 1600/1000/170 Heating platen size 500 X 510 X 63 mm Sliding platens Top and bottom ejectors Clamping force 1600kN Opening force clamp 100kN Clamping stroke 395mm Injection volume E 1000 ccm Max. Injection Pressure E 2200 bar Injection volume EF 170 ccm Max. Injection Pressure EF 1800 bar Hours: 700 since new Year 2009 Weight 6000kg
clamping force: 450 kNinjection volume: 99 cm³screw diameter: 30 mmplaten size: 860 x 320 mmclosing stroke: 406 mmCondition: used,Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083Clamping unit:- Clamping force: 450 kN- Opening travel: 406 mm- Heating plate size: 860 x 320 mm- Mould height min.: 264 mm- Max. plate spacing: 464 mm- Ejector stroke: 20 mm- Ejector force: 20 kNInjection unit:- Screw diameter: 30 mm- Screw length L/D: 16- Dosing stroke: 140 mm- Stroke volume max.: 99 cm³- Max. spray weight: 114 g- Screw speed: 20 - 300 rpm- Injection flow: 106 cm³/s- Injection flow increased: 71 cm³/s- Special injection pressure: 1451 bar- Spec. injection pressure increased: 2205 bar- Nozzle path: ...
Panstone 800ton Press Slabside type, Single Station Manufacturer: Panstone Main ram diam. 14” x 4pcs (200ton x 4pcs) Clamp Force 800 Ton Max Piston Diameter 600 mm diameter Working Pressure 210 kg/cm2 Stroke Max 600 mm Daylight Max 600 mm Electric Heating platen size 2500x2500 Heater Capacity 34.8 KW Oil Reservoir 870 l Year of Manufacture 2010
Maplan Injection Moulding Machine Model: MTF400/80C 80 Ton Safety distance 162mm Run-on time 81ms Follow-up 5mm Pattern size 510mm x 410mm Touch screen control Year 2010 ... más información
cross-section width:: -- mmcross-section heigth:: -- mmfeed:: -- mmspeed of feed:: 0,4 - 20 m/minThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
clamping force: 350 kNinjection volume: 58,5 cm³screw diameter: 28 mmplaten size: 260 x 254 mmCondition: used,Specification: injection moulding machine for TPE - usedclamping unit:- clamping unit: vertical- clamping force: 350 kN- opening stroke max.: 300 mm- platen distance max.: 500 mm- Mould installation height min.: 200 mm- Clear width between tie bars: 260 x 254 mm- Ejector stroke max.: 80 mm- Clamping unit: VV- Lift of protective bonnet: 500 mmInjection unit:- Screw diameter: 28 mm- Screw L/D ratio: 18.6- Screw stroke max.: 95 mm- Injection volume max.: 58.5 cm³- Injection pressure: 1577 bar- Plasticising flow: 8.6 g/s- Injection flow: 85.5 g/s- Connected load: 3x 400 V, 50 Hz- Max. heating power: 5.8 kW- Drive power: 7,4 kW- Total power: ...
machine measurements: 2.200 x 1.200 x 2.260 mmmachine weight: 1.000 kgpower capacity: -- kWCondition: usedSpecification: automatic control machine for O-rings - second-hand rotary transfer machine with 16 pick-up stations- year of construction approx.: 2011 - pick-up stations: 16- measuring range: ID from 55 - 90 mm cord from 2,5 - 3,5 mm (ID 55 - 70 mm) cord from 2.5 - 4.5 mm (ID 70 - 90 mm)- Part throughput: approx. 3 - 4 seconds per part approx. 900 - 1,200 parts per hour approx. 21,600 - 28,800 parts per day- Technical application: surface defect and crack detection on O-rings- Sorting function: Good, Bad, Undefined- Dimensions LxWxH approx.: 2,200 x 1,200 x 2,260 mm- ...
Wind-u for AUMA / Rotocure, Calender,.. transportable, plug and play E+L centering ... más información
Qty 1 x Carter MK6 direct drive Banbury internal mixer, Serial no. 237/11 (New chamber/hydraulic hopper in 2011/12), Hydraulic hopper, Chamber volume: 160L, 2 wing rotors, SSA type dust stops, hydraulic drop door with linear actuator, pneumatic oil injector fitted to end frame, hydraulic hopper, PIV semi unidrive gearbox (28:1 ratio), 310/620kW power rating, 728/1484rpm input speed, 26/53rpm output speed. Currently fitted with fixed speed motor fitted - 355kW, 744rpm to give rotor speed 26.5rpm. Complete with lubrication unit, hydraulic unit, electrical controls etc and in very good condition (inspection report carried out by Farrel available on request).