prensas usadas para venda

Capacity 250 ton Kinetic energy of moving parts at the end of max. ram stroke 13,5 kj Max. ram stroke 400 mm Number of ram stokes (SPM) 34 Slide clearance 560 mm Ram size (front-back 560 mm Table size 670 x 750 mm Lower ejector capacity 16 ton Lower ejector movement 105 mm Main drive motor powe 15 kW Press dimensions 3710 x 1925 x 4415 mm Press weight 18000 kg

Capacity :10 tons, Weight of falling part,nominal mass of drop parts without upper instr.:9 tons, Effective working kinetic energy after blow :25000 kg mtr., Max. working ram stroke :1400 mm, Max no of blows : 30/min , Distance between slides : 1000 mm, Shut height : 775 mm , Ram size front to back :1200 mm, Bolster size front to back :1200 mm, Air pressure : 7-9 MPA , Height of instruments : 450 min., Die-holder front to back dimensions: 1400 mm, Height above floor level: 7270 mm, Hammer dimensions : 4400x10420x2700 mm, Weight (less anvil block): 73.5 ton, Weight of anvil block : 203.8 tons.

Pressing of profiles up to a profile height of 68 mm Pressing force: 40 kN Pneumatically movable counter bearing, mechanically locked With support arms Weight: approx. 240 kg  ... mais informação

YOM (2008); Max. Roll Length 17 Meter; Min. Daylight between Roller 960mm; Max. Ram stroke 1040 mm; Top Roll diam. 480 mm; Bottom Roll 400 mm; 6 sets of Back-up Rolls; Min/Max Bottom Roll Centers 500/800 mm; Pressing Speed 1 to 6 mm/sec. ram approach 60 mm/sec; main motor 125 HP. Including control panel, panel boxes and conveyors. Weight: 600.000,00 Capacity: 2000 TON, Working size: 17000mm x 35t, 5500 x 40t

(2007); Max. Roll Length 20 M; Min. Daylight between Roller 960 mm; Max. Ram stroke 1050 mm; Top Roll diam. 500 mm; Bottom Roll 420 mm; 8 sets of Back-up Rolls; Min/Max Bottom Roll Centers 500/800 mm; Pressing Speed 1 to 6 mm/sec. Ram Approach 60 mm/sec; Main Motor 125 HP. Including Spare for Bottom Roller, control panel, panel boxes and conveyors. Capacity: 2200 TON, Working size: 20,000mm x 25t, 5,000mm x 40t

Pneumatic press 2643 Assembly through pivot table outside the working area With protective cage and release only with a retracted swing table Table size: 10 cm x 10 cm  ... mais informação

Pneumatic press with foot-tripping  ... mais informação

Used Hydropneumatic Press / Assembly Press / Printing Joining Press - Pressing force 10 KN (1 to) - Used hydropneumatic cylinder make TOX - Pneumatic two-hand control - Portal frame aluminum profile 90 90 mm - Machine table made of aluminum profiles and multiplex plate 700 700 mm - Total weight approx. 50 kg Suitable as an assembly press for insezing components. With x- and y-adjustment alignable vice for die diameters up to 80 mm. Or for small punching or embossing tools. All tools or vices are quickly changed through the groove system.

Manual written press for stamping of letters and numbers  ... mais informação

Pneumatic pin press for printed circuit boards  ... mais informação

Pneumatic pin press for printed circuit boards  ... mais informação

Hand lever press to push pins in printed circuit boards  ... mais informação

The small laboratory press MHSP5 can perform very well with the round stamp (70 mm diameter) deformations of many materials. By delivering fine (0.5 mm per wheel revolution), deformations are carried out very accurately. Small punching or stamping operations are possible. The press is driven by a worm gear screw jacks, which requires minimal hand strength by high reduction ratio. The pressing frame consists of stable-dimensioned polyamide PA6G. Here are some technical data:-static force 5 KN (0.5 to) - portable presses frame made of polyamide PA 6 G, very stable design, with FEM program added - spindle manual jacks 20 mm, pitch 5 mm - with Handwheel diameter 120 mm and handle - gear ratio 1:10, per the Handwheel 0.5 mm screw - table size 235 195 mm - clearance width 190 mm - stamp size diameter 70 mm with 4 holes 8 mm for mounting a major stamp Very easy operation with spindle and w ...

Hand spindle press to push pins in printed circuit boards 2 presses on a plate, with a dial indicator.  ... mais informação

Control: STE 328-89-1 1/2" complete TOX Powerhouse: S75.160.200.12D Table size: 996 x 695 mm Installation height: 600 mm Total stroke: 150 mm Power stroke: 10 mm Weight: 5700 kg Electrical connection 230 V  ... mais informação

Capacity: 125 ton, Strokes per minute: 85-500 / min, Slide: 870 x 550 mm, Plate width: 260 mm, Year of manufacturing: 1980 ... mais informação

year 1985 Capacity 2500 / 2750 Ton 24900 / 27400 kN Speed 65 SPM, continuous mode Ram/Slide Stroke 12.60in, 320.00mm Ram/Slide Adjustment 0.39in, 10.00mm Shut Height (Ram / Slide Down, Adjustment Up) 35.60in, 905.00mm Stroke of Upper Knockout 2.00in, 50.00mm Stroke of Lower Knockout 2.80in, 70.00mm Ram/Slide Width 52.00 in, 1320.00 mm Ram/Slide Height 43.00 in, 1100.00 mm Bed Width 53.00 in, 1340.00 mm Bed Depth 55.00 in, 1400.00 mm power Existing Additional 28 Strokes per minute in manual mode, height shown is above floor, total height is 291 in ( 7390 mm), new quick change hydraulic type bolster Machine Length 160.00 in, 4055.00 mm Machine Width 157.00 in, 4000.00 mm machine height 264.00 in, 6710.00 mm Weight 320000 lbs, 145455 kg Condition Excellent Currently disassembled an ...

VORONEZH K8544 Hot Forging press YEAR : 1980 / 2008 OVERHAUL AND INSTALLED FORCE : 2500ton RAM STROKE : 350 mm RAM SIZE : 1120X1070 mm TABLE OVERALL SIZE : 1400X1200 mm NUMBER OF STROKES IN CONTINUOUS MODE : 60 NUMBER OF STROKES IN MANUAL MODE : 26 SHUT HEIGHT : 890 mm STROKE OF UPPER KNOCK OUT : 60 mm STOROKE OF LOWER KNOCK OUT : 70 mm MAIN MOTOR : 132KW (CHANGED TO HYUDAI HEAVY Y2012) PRESS OVERALL DIMENSION : 5380X4680X6400 mm HYDRAULIC BOLSTER NEW IN 2007 CONDITION : VERY GOOD WORKING CONDITIONS Trimming press available

SMERAL LZK 2500 Hot Forging press Fully refurbished in 2024 Capacity: 2500 Ton Speed: 65 SPM, continuous mode Ram/Slide Stroke: 320.00mm Ram/Slide Adjustment: 10.00mm Shut Height (Ram/Slide Down, Adjustment Up): 905.00mm Stroke of Upper Knockout: 50.00mm Stroke of Lower Knockout: 70.00mm Ram/Slide Width: 1320.00 mm Ram/Slide Height: 1100.00 mm Bed Width: 1340.00 mm Bed Depth: 1400.00 mm Power: 130kW Machine Length: 4055.00 mm Machine Width: 4000.00 mm Machine Height: 6710.00 mm Weight: 140000 kg Condition: like new refurbishing report: 1. Mechanical part • Complete disassembly of the press. • Measurement and troubleshooting of all parts. • The main parts of the press are tested (without destruction) in order to identify any defects. Frame: The frame was inspected and non-destructive testing of the most loaded areas was carried out. Damage to the table pl ...

2000 Ton Sumitomo Hot Forging Press line Year 2006 Stroke 350 mm (13.78") Strokes per min 75 Shut height 850 mm (33.47") SlideAdj. 7 mm (.27") Ram size 1200 mm LR X 1300 mm FB Bed size 1320 mm LR X 1300 mm FB 4 stage transfer system Slide knockout Bottom knockout Scrap System Dual Die Changer Extra Die Shoes Billet Heater and Billet Saw Also Available This line was used by HONDA to make transmission gears, It takes a billet, cuts it to size, heats it to 1300 C then the press hits it 4 times. It can determine good from bad parts, the bad parts get sent to a quench tank, the good parts get sent into a cool down conveyor that you can pick the parts up by hand at the end. The entire system was ran by one operator.