outras máquinas para trabalhar o metal usadas para venda

AMP VBF-60/60/100-1.5 horizontal vacuum furnace was manufactured in Poland in 2012. The machine, which has a horizontal construction with a large cylindrical heating chamber, is designed for, among others, annealing, degassing, brazing and hardening of long workpieces with a maximum weight of 600 kg, without the risk of deformation. The AMP vacuum furnace ensures that a constant temperature of 1180°C is maintained throughout the treatment, due to the insulation inside the heating chamber in the form of a graphite mat fixed to the chamber casing by molybdenum rods with graphite composite pads. The capacious heating chamber also contains heating elements, charge holding supports and cooling nozzles through which cooling gas flows during the cooling cycle. All parameters, such as vacuum, temperature course and cooling gas pressure, are programmed in a special controller, installed in a  ...

ZREMB GH4 tube bending machine, manufactured in 1983, is used in factories during the precise processing of all varieties of installation tubes. The tube bending is performed in a semi-automatic mode on a cam with the mandrel filling the most deformed section of the tube. The machine comes with a comprehensive range of equipment shown in the accompanying photos. The GH4 mandrel bending machine weighs 2450 kg. The ZREMB tube bending machine consists of: – drive mechanism – mandrel feed mechanism – guiding mechanism – control panel mechanism – hydraulic system – electrical installation assembly – frame assembly Technical specification of the ZREMB GH4 bending machine - tube diameters: 1 ½”; 2″, 2 ½”; 3″, 3 ½”; 4″ - maximum bending angle: 180° - bending capacity (30 bends): 180°/h - head working movement time (180°): 38 s - head return movem ...

DEA SCIROCCO 151310 coordinate measuring machine built in 1997 in Italy, is used to make fast and highly accurate measurements of workpieces with complex shapes. Workpiece measurements are taken using contact or non-contact methods, which are then represented as a set of point coordinates. The dimensions of the measured workpiece are taken using the RENISHAW TP7M measuring probe, which is installed on the RENISHAW PH10MQ indexing head. The measuring probe uses strain gauge technology to eliminate granularity errors and achieve the highest measurement quality in the X,Y,Z axes with feeds of 1500 mm (X axis), 1300 mm (Y axis) and 1000 mm (Z axis). The measuring machine is offered with a wide range of equipment, including an advanced PC-DMIS package for Windows, performing detailed geometric measurements. The total weight of the machine is 3650 kg. Technical data of the DEA SCIROCC ...

ABB IRB 2400 M2000 robotic machining cell manufactured in 2004 in Switzerland, is equipped with an ABB IRB 2400/16 6-axis industrial robot and an ABB IRC5 controller for the control of the manipulator and peripherals. The machining station has so far been configured and used for milling of allowances after thermoforming workpieces. The high-performance milling robot has an arm with a maximum reach of 1550 mm, capable of handling workpieces weighing up to 16 kg. The industrial robot achieves the best cycle performance thanks to modern technology that automatically optimises parameters and executes the programmed path regardless of speed or operating mode, even after an emergency stop or power failure. The BaseWare OS operating system is used to fully control every aspect of the machine, ensuring the highest machining accuracy is achieved. The robotic milling station is offered with  ...

FRECH DAK315H die casting machine manufactured in 1991 by the German company Oskar Frech Werkzeugbau GmbH + CO. KG. is designed for the production of castings by filling moulds with molten brass or aluminium. The reliable FRECH metal injection moulding machine with high-quality components works with casting moulds of a maximum height of 700 mm, which are closed with a force of up to 315 tonnes after being filled with molten material. Depending on the design of the choiceed mould, the aluminium die casting machine also allows for the use of an injection piston with a diameter of 40 to 80 mm. Previously, the machine used a piston with a diameter of 40 mm. The DAK315H aluminium die casting machine weighs approximately 14000 kg. Technical parameters of the FRECH DAK315H metal injection moulding machine - clamping force: 315 t (3150 kN) - injection force: 35 t (350 kN) - ejection for ...

WIWOX MC 110 II ultrasonic cleaning machine, built in Germany in 2004, cleans metal parts from unwanted deposits using ultrasonic waves. The use of such technology allows for fully professional cleaning of workpieces, as well as preventing surface damage and saving time and costs. The ultrasonic cleaning machine allows for cleaning workpieces weighing up to 110 kg, even in the most inaccessible places. The cleaning process takes place in a working chamber with dimensions (L x W x H) of 516 x 360 x 435 mm, where the placed workpiece is cleaned by ultrasonic waves at a temperature of 80°C for approximately 5-15 minutes. The total weight of the device is 280 kg. Specification of WIWOX MC 110 II ultrasonic cleaning machine - dimensions of the working chamber (L x W x H): 516 x 360 x 435 mm - maximum weight of workpiece: 110 kg - ultrasonic power: 1.2 kW - connection power: 6.2 kW  ...

ZOLLER SMILE / PILOT 3.0 presetting and measuring machine was manufactured in 2019 in Germany. The machine is a professional tool measuring and presetting device, whose easy operation and precision guarantee flawless results. A telecentric lens and a CCD camera with integrated LED ring for measurements in reflected light (blade inspection) are used to perform the measurements. ZOLLER SMILE 420 is equipped with the CNC controller ZOLLER »pilot 3.0« and functions such as automatic blade recognition, measurement of radial run-out and axial run-out, maximum contour function and cutting edge control. The tool to be measured can have a maximum length of 420 mm and a maximum diameter of 420 mm. Specifications of the ZOLLER SMILE / PILOT 3.0 presetting and measuring machine - maximum tool length Z: 420 mm - maximum tool diameter D: 420 mm - diameter measurement according to Abbe’s p ...

The FORNI INDUSTRIALI FIBEX COMBI 6GX-10.130-7110.2E.270 brazing furnace was built by the Italian company Forni Industriali Heat Treating Plants in 2007. The furnace is used for soldering steel elements with solder paste at temperatures up to 1120 degrees Celsius. At the entrance and exit of the furnace, two pairs of gas burners (so-called safety pilots) are installed to prevent the escape of the protective atmosphere outside the furnace. Electric heaters powered by thyristor temperature regulators are responsible for the proper temperature in the furnace. The belt furnace has a conveyor speed adjustment in the range from 0 to 500 mm / min, and the working length of the soldering zone is 7100 mm. The furnace for brazing steel elements was modernized in 2021 - the thermal insulation and the cooling module for sections 1 and 2 were replaced. The cost of the modernization was 70,000 Euro.  ...

ERMAKSAN LASERMAK 6000 6X2 laser cutter was produced in 2014. Technical parameters: – laser source: 6000 W CO2-laser GE Fanuc C6000i-Model C – RF-excitation: 2 MHz – power stability: ± 2% (power monitor) – laser wave length: 10.6 μM – beam mode: Fanuc Low Order Mode – laser shutter: mechanical safety shutter – laser gas composition: CO2 / He / N2 – gas consumption by laser: 20 l / h – cooling water flow rate: 250 l / min – maximum cutting capacity: mild steel 25 mm (during tests the maximum achieved: 30 mm), stainless steel 15 mm, aluminum 12 mm - machine activation time: 22899 h - working time: 10122 h - cutting time: 8429 h – total energy requirement: 100-120 kW – cutting head focal length: 5 -7” -10 inch – maximum worksheet size: 6150 x 2000 mm – maximum burden capacity: 4000 kg – machine axes: 5 axes [X, Y, Z, U (X2), V] – axis ...

Gabion Mesh Production Line HEBEI ANPING WIRE MESH MACHINE FAKTORY 60X80 / 4300 was built in 2013. Machine for the production of hexagonal gabion mesh with the following parameters: - manufacturer: Hebei Anping Wire Mesh Machine Faktory (China) - mesh size: 60 x 80 mm or 60 x 100 mm - maximum width of the produced mesh: 4300 mm - wire diameter: 2.0-2.8 mm - capacity: up to 2.5 m / min - machine weight: 18 tons - engine power: 22 kW

Hardening furnace ZWUT PSK-1 built by ZWUT. It is intended for various types of laboratory and industrial work. Technical data : - power consumed at T = 1350 degrees C: 4,10 kW - installed power: 5.5 kW - power supply voltage: 220 V, 50 Hz - secondary voltage of the autotransformer: 7-41, 1-3-58, 9-5-84, 4 - number of phases: 1 - nominal temperature: 1350 degrees Celsius - temperature control accuracy: 1.5 (or 0.2 + /%, when working with a feedback attachment) - type and number of silites: 8/150/150/10 mm / pcs - warm-up time to T: about 3.5 hours - usable dimensions of the heating chamber (height x width x length): 150 x 150 x 280 mm - furnace weight: 138 kG - weight of the cabinet: 81 kG

Wire EDM machine SODICK A 600 manufactured in 1997. Technical parameters of the SODICK A 600 EDM machine: - table travel (X axis): 600 mm - table travel (Y axis): 400 mm - Z axis travel: 270 mm - maximum dimensions of the processed part (width x depth x height): 800 x 550 x 260 mm - maximum weight of the workpiece: 900 - auxiliary table travel (U axis x V axis): 70 x 70 mm - wire diameter: 0.1 ~ 0.3 mm - maximum wire speed: 250 mm / sec. - wire tension: 0.2 ~ 2.8 kgf - cutting inclination at an angle: + -15 degrees per 100 mm of thickness - height from the floor to the surface of the working table: 1000 mm - machine tool dimensions (width x depth x height): 2188 x 2645 x 2100 mm - machine tool weight: 3700 kg

Ultrasonic cleaner GT85 GT 2000-3P built in 2008. The washing tub is made of 316L stainless steel, the other tubs are made of 304 stainless steel and the supporting structure is made of structural steel. The volume of washed products should not exceed (LxWxH) 2400 x 600 x 600 mm Industrial washer - technical data: - external dimensions (LxWxH): 6400 x 4400 x 2800 mm - usable dimensions: chamber I (washing and phosphatizing): 2800 x 800 x 900 mm - useful dimensions: chamber II (rinsing): 2800 x 800 x 900 mm - usable dimensions: chamber III (drying): 2800 x 800 x 900 mm - power consumption: 63 kW - total weight: 2500 kg Bathtub 1: - preparation type: Ruster P02, Roklin P11 - pH: 2-4 - bath operating temperature: 20-60 degrees C - total bath capacity: 2000 l - maximum product weight: 500 kg - maximum product volume: 250 dm3 Bathtub 2: - type of preparation: tap water  ...

The CIMAT CMT 30 V2 balancing machine was manufactured in 2015 in Poland. Bvcilkrj7m Basic technical data: - software: ROTOTEST - component weight: 0.2 to 30 kg - maximum rotor diameter: 400 mm - maximum rotor height: up to 200 mm - compressed air pressure: 0.6 MPa - balancing machine dimensions: 1200 x 1200 x 1500 mm - control panel dimensions: 600 x 600 x 1800 mm - weight: 500 kg

Programmable focusing optics Manufacturer: Trumpf Type: PFO 33-2 R1030-1070 HA Year of Make: 2017  ... mais informação

Feed: BBV 190 / 85 H Year of Make: 1999 Machine hours: approx. 65,000h Tool safety: PAS 6000 Machine is in good condition  ... mais informação

Rolling motor 5, 6kw GS motor with tachometer and forced-air cooling Maximum band width: 180 mm Maximum belt thickness: 4, 5 mm Number of leveling rollers: 4pcs above 5pcs below  ... mais informação

Reinforced steel scissors Round iron scissors Scissors Manufacturers Muhr and Bender Type 50N/22 and 50N/28 50N/22 intersects at 450N/mm2: Round: 22mm Square 22mm Flat: 35x10mm 50N/28 intersects at 450N/mm2: Round: 28mm Square 24mm Flat: 40x15mm Both machines new and ovp Special price

Various threaded rollers ... mais informação

Portable Leybold Helium Leak Detector Ultratest UL100Plus  ... mais informação