other wood working machines used for sale

Manufacturer: Rippert, Type: N-355 B, Year: 1995, Diameter intake mm: 355, Engine power kW: 3, Flow rate approx. m3/h: 3000-6000, rotations rpm: 1415, Direkt drive: yes, Pressing: 1080, Wight approx. kg: 200, Required space L x W x H mm: 1000 x1000, Year :1995 ... more information

– after technical inspection – very good condition – year of production 1995 TECHNICAL PARAMETERS: turning length max. 1300 mm turning diameter 120 mm three bottom knives five top knives support hydraulic knife control automatic control magazine dimensions of the machine (L/W/H) 380 / 210 / 215 cm weight ~ 3490 kg

Remote-controlled gate loading system H38 For the block-initiating gate incision at high feeds. The gate guide sits in a stationary operating stand with a good overview of the entire cutting system. The machine is in very good condition and can be delivered with new control on request! ... more information

Technical data: Roll width: 800mm Roll diameter: 152mm Length: 9700mm Roll spacing: 800mm Power: 2.2 KW Accessories: Abort ingenurole (right) Lifting and sinks counter-rotating thread roller  for max. wood length 7.0m, threaded roller is located 2.5 m before the roller aisle end

achkettenquerförderer or Auschutisch with pull-off cross conveyor. Chains with roof chain takers. 5 chain strands. Length 5,900 mm. Spread width 2,000 mm. Total width 2,400 mm. Chain spacing: 750 - 750 - 1250 - 2000 mm. Fully plated. Drive via gear motor with 3 KW and adjustable slip clutch. Sprockets with clamping elements. Chain 80 x 40 x 6 mm. Technically reviewed and tested. Trial run possible.

Hot air Shrink tunnel for packaging e.g. briquettes or long products hot air shrink tunnel for packing of fire briquette or long woolden products  ... more information

Manufacturer: IMA, Type: Quadromat 4012 F, Year: 1995, Program: yes, Min-max edge material mm: 0,5 - 8,0, Min.-max. workpiece length in mm: 250, Min-max feed m/min: 10, Premilling: yes, Min.-max. batten magazine mm: 0,5 - 8,0, Mitre stations: yes, radius milling: yes, Corner tracing type: yes, 2 Motoren: yes, Year :1995

Manufacturer: IMA Kantenbearbeitung , Type: U/F 720, Year: 1995, Programm: yes, Achsteuerung: no, Edgeband thickness max mm: 3, Edgeband height max mm: 60, Edgeband thickness max mm: 3, Edgeband height max mm: 60, Work piece thickness min mm: 70, Thickness of coiled edgeband max mm: 3, Panel length min mm: 250, Coil magazine: 12, Strip magazin: no, Premilling: yes, Power per lamp: yes, Glue system granulate/cartridge: Granulat, Soft edge single side: no, Mitre stations: yes, Trimming saw: yes, Flush/radius/chamfer milling: yes, Contour milling: no, Ziehklinge Radius: yes, Flat scraper: yes, Feeding speed max m/min: 10-25, Compressed air bar: 6, Year :1995

Manufacturer: KDP Kantenanleimmaschine, Type: KDP 111 SL, Year: 1995, Min-max edge material mm: 0,5-2,0, Work piece width min-max mm: 60, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 10-45, Min-max feed m/min: 8, Lasertechnik: yes, Mitre stations: yes, Radius milling axis adjustment: no, Year :1995

SECOND-HAND 5+1 SPINDLES MOULDER WEINIG MOD. PROFIMAT 23E - working width mm.230 - infeed working table 2000 mm. - 1st spindle horizontal bottom 4kw - 2nd spindle vertical right 7,5kw - 3rd spindle vertical left - 4th spindle horizontal top 7,5kw - 5th spindle horizontal bottom 4kw - 6th spindle universal 4kw - volt 380/50 - s/n 228-80241 - year 1995 (CE)

Gebr. Tenon cutter Carpentry Abundmaschine KRÜSI ZA-66/95 YOC 1995 CE version with protective cabin Crosscut saws: Motor power: 4.0 kW 65° swivel Lateral adjustment by handwheel travel: 250 mm max. saw blade diameter: 750 mm max. cutting height: 290 mm Cutting saw – slitting unit: Motor power: 7.5 kW 45° swivel Saw blade diameter: 2 x 450 mm max. cutting depth: 175 mm Settling saws: Motor power: top 2.2 kW / bottom 2.2 kW Complete sawing unit can be swivelled forward up to 45° Additional swivel heads: swivel by +/- 45° possible max. saw blade diameter: 350 mm max. cutting depth: 125 mm Sliding table: swivel +/- 60° on both sides Laser for cutting position indication for the swivel cross-cut saws Chassis Moving trestle Extraction connection: 2 x 120 mm and 2 x 80 mm Machine dimensions measured without sliding carriage: L: 470 cm W: 135  ...

Made in 1995 in Denmark. Machine No. 9585037. Made in 1995 Transport dimensions: 1800x620x2000 mm. Weight: 400 kg  ... more information

Slow runner with sliding floor Rotor width 800 mm 18.5 kw motor  ... more information

Slow runner with sliding floor 800 mm rotor width 11 kw motor good condition  ... more information

Manufacturer: Soenen, Type: SHCR, Year: 1996, Winkelschweissungen im Bereich von min-max Grad: verstellbar, Mit Schweissraupenbegrenzung an Tisch- und Spannplatten: yes, Spannhöhe min-max mm: 30-90, Kämpfer schweissen im Stumpfschweissverfahren: yes, Spannhöhe min-max mm: 30-90, Spannzylinder pneumatisch: yes, Schweissspiegel und Profilanschlag kommen von unten: yes, Einstellbare Schweissraupenbegrenzung: yes, Ausricht-, Abschmelz- und Stauchanschläge: yes, Digitale Anzeige der Schweisstemperatur: yes, Wight approx. kg: 500, Year :1996

KRÜSI chalet construction machine / log cabin production system type CM 40 Manufacturer: Krüsi Krüsi Maschinenbau AG CH-9105 Schönengrund AR Year of construction: 1996 S/N 431 Condition: good, technically checked and cleaned / ready for use Machine description / equipped with: 1. Sawing unit: Hand feed Spindle adjustment with analogue dimension display 2. CM milling unit: Hydropneumatic feed Spindle adjustment with digital dimension display 3. Drilling unit: Hand feed Spindle adjustment with analogue dimension display 4. End milling unit Hydropneumatic feed Spindle adjustment with digital dimension display Specifications Workpiece Cutting height max. 200nn Cutting width max. 250mm Working table height 900mm Sawing unit Saw blade Ø max. / bore ø 400 / 30 mmm Tungsten carbide equipped with chip depth limiter (synchronization)  ...

Radial fan, centrifugal fan, centrifugal blower, chip extraction fan, fan, suction, chip blower, high performance fan-Manufacturer: Reitz, radial fan chip extraction fan type MXE 020-018030-00-Engine: Dutchi DM 160 MX2 15 kW-Speed: 2935 rpm-Volume flow: 180 m³/min / 10800 m³/h-Connection input: Ø 245 mm-Connection output: Ø 390 mm-Dimensions: 1460/1160/H1500 mm-Weight: 392 kg

Edge bander with manual operation and hot melt glue application for shaped panels Panel thickness: 10 to 40 mmEdge thickness: 0,5 - 1 mmFeed speed: ca. 4 m/minOnly coil edges ... more information

An edge banding line including feeding, turning device and an automatic drilling machine is available. The longitudinal machine enables the processing of thick edges and is equipped with new units and controls. The transverse machine can only process thin edges as there is no coupling unit. The machine was operated at up to 28 cycles per minute. Control system: Imatronic 150, documentation is available. Control system: Imatronic 150, including spare parts and tools. Documentation is available.

KRÜSI chalet construction machine / log cabin production system type CM 40 POS 1: Motor-driven roller conveyor Working width 400mm, infinitely variable feed speed 2.0 kw motor, length 6000mm POS 2: Ripsaw Diameter saw blade 400mm Pneumatic feed of the sawing depth Main motor 4.0 kW POS 3: KRÜSI chalet construction machine / log cabin production machine type CM 40, year of construction approx. 1985 Horizontal milling unit Cutter - Ø 180mm Cutter width max.130mm from cutter width 60 mm only cutters made of aluminum alloy with 1 motor with manual feed, kW 2.2 POS 4: Drilling unit: Hydropneumatic feed Clamping Ø max. mm 16 Drill bit- Ø max. mm 32 Motor min'1 1450, kW 1,8 POS 5: KKRÜSI RÜSI chalet building machine / log cabin production machine type CM 40 Machine No.431 Year of construction: 1996 Sawing unit: Hand feed Spindle adjustment wit ...