trabalho de chapa metálica usadas para venda (3,271)

Hidráulico de 3 rolos com configuração planetária dupla pré-aperto. novo para completar, 45 dias a partir da ordem. -Largura da placa 3000 mm -Espessura da placa rolante de capacidade 50 mm -Pre-beliscar espessura da placa 40 mm Configuração da máquina e acessórios instalados: -comprimento útil da superfície nos rolos 3100 mm -tamanho de rolo superior 480 mm -tamanho de rolos mais baixo 440 mm -Leituras de posição digital. - Endurecimento do tratamento dos 3 rolos. -3 rolos acionados hidráulico motorizados com caixa de engrenagem axial independente em cada rolo. -Acessório de flexão cónico da placa com rolos inferiores inclinados hidráulico. -Certificação de qualidade CE, fabricado na fabricação italiana. -Manuais de serviço e manuais de instruções de funcionamento. -Diagramas hidráulicos - Esquemas elétricos & eletrónic ...

320 toneladas x 4100mm

Máquina de dobra de chapas Kramatorsk de 4 rolos Resistência máxima à tração do material: 500 MPa (50 kg/mm²) Resistência ao rendimento – flexão a frio: 250 MPa (25 kg/mm²) Resistência ao rendimento – flexão a quente (primária): 100 MPa (10 kg/mm²) Resistência ao rendimento – formação a quente (aquecimento secundário): 45 MPa (4,5 kg/mm²) Alongamento no estado frio: ±18% Largura máxima da folha: 4000 mm Espessura máxima da folha – frio, sem pré-curvatura: 71 mm Espessura máxima da folha – frio, com pré-flexão: 63 mm Espessura máxima da chapa – conformação a quente: 150 mm Raio de curvatura mínimo – frio: 560 mm Raio de curvatura mínimo – quente: 600 mm Raio máximo para flexão fechada (borda enrolada): 1000 mm Motor principal: 160 kW Peso: 730 toneladas

Máquina de dobragem de placa de 4 rolos Mod. VRM NG HY 3000x40 País de fabrico: Suíça YOM: 1997 Marca: HAEUSLER AG Diâmetro do rolo 560/540/400 mm Espessura do rolo 40mm Comprimento do rolo 3000mm Motor motor Potência:55kW Sistema: Hidráulico Tensão: fase 380V/3 Peso 45 000kg A qualidade da máquina ainda é muito boa.

: gebraucht : WA0149 : 690 €: 1 : 3010 mm: 24 mm: 160 mm: 10 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : Türkei : 24500 €: 470.4 €: 1550 mm: 4.5 mm: 4.5 mm: 3.5 mm: 4.5 mm: 3.5 mm: 3.5 mm: 2.5 mm: 130 mm: 130 mm: 130 mm: 5 m/min: 2,2 + 1,1 kW: 3300 mm: 1150 mm: 1110 mm: 2370 kgmotorized roller driveupper and lower roller drivenhydraulic side roll feed3 digital displayshydraulic folding bearingshardened rollersconical bending deviceuser manual in GERMAN or ENGLISHOPTIONAL EQUIPMENT (PRICES ON REQUEST):overhead craneside supportsNC controlvariable speedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0151 : 217 €: 1 : 835 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0039 : 180 €: 1 : 415 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0143 : 690 €: 1 : 3100 mm: 90 mm: 25 mmmint conditionThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0127 : 1230 €: 1 : 2500 mm: 70 mm: 70 mm: 8/11/12/16/24/36 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0011 : 292 €: 1 : 835 mm: 80 mm: 12 mmmint conditionThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0012 : 292 €: 1 : 835 mm: 80 mm: 12 mmmint conditionThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0013 : 265 €: 1 : 835 mm: 80 mm: 12 mmmint conditionThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0052 : 292 €: 1 : 835 mm: 80 mm: 16 mmmint conditionThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0053 : 292 €: 835 mm: 80 mm: 16 mmmint conditionThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0054 : 292 €: 1 : 835 mm: 80 mm: 16 mmMint conditionThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0102 : 292 €: 1 : 835 mm: 80 mm: 25 mmmint conditionThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0147 : 890 €: 1 : 3050 mm: 105 mm: 85 mm(screwed 5x from above)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0145 : 840 €: 1 : 3100 mm: 40 mm: 115 mmslightly crankedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : 2026 : 090194 : prompt, Zwischenverkauf v : Spanien : 22400 €: 430.08 €: 1 : 1 : 60 to: 250 mm: 5 : 40 x 11 mm: 32 1/min: 350 x 15 mm: 120 x 10 mm: 45 / 40 mm: 10 mm: max. 150x10 mm: 5.5 kW: 1850 mm: 1300 mm: 2100 mm: 1390 kgwith bending station5 working stationsflat steel shear with device to reduce deformationangle iron shear with round- and squarebars openingtriangle notcherpunching stationpress brake device for flat steeltable at flat steel stationtable at notching stationlength stop 1000 mm with contact switch, for angle, flat or bar stationhydraulic drive2 foot releaseuser manual in GERMAN and ENGLISHWE HAVE MORE THAN 700 REFERENCES!The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : 2026 : 090209 : prompt, Zwischenverkauf v : Italien : 7780 €: 150.15 €: 1 : 1 : 42 mm: 400 mm: 570 mm: 1000 mm: 80 kg: 4 cm³: 42 x 3 mm: 48 x 1,5 mm: 42 x 4 mm: 42 x 2 mm: 42 x 2 mm: 50 x 3 mm: 54 x 2 mm: 54 x 2 mm: 60 x 2 mm: 50 x 4 mm: 30 mm: 40x20 (liegend), 40x12 (s mm: 260 mm: 10 mm: 3,3 U/min: 1.1 kWmanual clampingelectronic preselection of bending angledigital read our for Clamping position30 programms with each 9 bendsmaterial spring back compensationoverload protectionmobile by rolls and handlefoot pedaltools not includedAlternatively also available as following models (prices on request):MB 42M (single phase, 2 U/min) MB 42PM (portable, single phase, 2 U/min)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 4 Wochen ab Auftragse : Italien : 10900 €: 209.28 €: 60 mm: 595 mm: 363 mm: 900 mm: 130 kg: 10.5 cm³: 60 x 3 mm: 2Gas x 3,91 mm: 60 x 4 mm: 60 x 2 mm: 60 x 4 mm: 60 x 4 mm: 64 x 4 mm: 64 x 4 mm: 60 x 4 mm: 50 x 4 mm: 35 mm: 60x30x4 stehend, 60x40x5 mm: 300 mm: 10 mm: 10 mm: 1,25 / 2,50 U/min: 1.5 kWdigital read out for bending anglemanual clampingmaterial spring back compensationdigital read out and zero setting for clamping point2 speedsoverload protectionmobile by rolls and handletools not includedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 8 Wochen ab Auftragse : Italien : 12460 €: 239.23 €: 60 mm: 500 mm: 760 mm: 1000 mm: 186 kg: 10 cm³: 60 x 4 mm: 2 x 3,91 mm: 60 x 4 mm: 60 x 2 mm: 60 x 3 mm: 60 x 6 mm: 64 x 6 mm: 64 x 6 mm: 63 x 4 mm: 50 x 4 mm: 35 mm: 35 x 35 mm: 60 x 20 stehend, 60 x 35 mm: 380 mm: 10 mm: 10 mm: 1,5 / 3 U/min: 1.5 kWquick-change tooling systemdigital display of bending anglematerial spring back compensationfoot pedal for hands-free operationaccurate counterbending die positioningusers manualtools not included, priced on requestThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 8 Wochen ab Auftragse : Italien : 29100 €: 555.81 €: 100 mm: 500 mm: 1200 mm: 850 mm: 480 kg: 43 cm³: 100 x 6 mm: 3 1/2 x 4 mm: 100 x 6 mm: 100 x 3,6 mm: 100 x 3,6 mm: 114,3 x 6,3 mm: 114,3 x 6,3 mm: 114,4 x 6,3 mm: 88,9 x 3,65 mm: 100 x 5 mm: 70 mm: 100 x 25 stehend, 100 x 5 mm: 400 mm: 36 mm: 10 mm: 0 - 1,3 U/min: 3.5 kWquick-change tooling systemdigital display of bendmaterial spring back compensationremote control of bend, return and emergency stop functionsaccurate counterbending die positioningfootswitch3 hexagonal tool holdersheavy-duty steel gear caseusers manaultools not included, prices on requestThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 8 Wochen ab Auftragse : Italien : 39500 €: 754.45 €: 127 mm: 850 mm: 1200 mm: 850 mm: 720 kg: 80 cm³: 127 x 7,1 mm: 4 x 8,56 mm: 127 x 7,1 mm: 114,3 x 5,6 mm: 114,3 x 5,6 mm: 139,7 x 8,8 mm: 139,7 x 8,8 mm: 64 x 6 mm: 88,9 x 3,65 mm: 50 x 4 mm: 90 mm: 130 x 25 stehend, 130 x 6 mm: 700 mm: 36 mm: 10 mm: 0 - 0,75 U/min: 3.5 kWdigital read out for bending angle4 hexagonal tool holders (40, 50 80 and 110 mm)Possibility to bend left and rightUsers manaulTools on requestThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 10 Wochen ab Auftrags : Italien : 106340 €: 2009.83 €: 150 mm: 1000 mm: 1900 mm: 1475 mm: 2700 kg: 170 cm³: 150 x 7,1 mm: 6 x 7,11 mm: 150 x 9 mm: 141,3 x 6,55 mm: 141,3 x 6,55 mm: 168,3 x 9 mm: 168,3 x 9 mm: 64 x 6 mm: 88,9 x 3,65 mm: 110 mm: 150 x 45 stehend, 150 x 6 mm: 800 mm: 100 mm: 10 mm: 1 U/min: 15 kWTCPlus Control with 7 TouchscreenProgrammable bending speed for each individual bendPossibility to bend left and rightUsers manaulThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : 2023 : 8286 : prompt, Zwischenverkauf v : Türkei : 2990 €: 1 : 2040 mm: 0.8 mm: 70 °: 2400 mm: 750 mm: 850 mm: 290 kgstraight upper toolmoveablemanual cutting deviceThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : 2025 : 090086 : prompt, Zwischenverkauf v : Türkei : 7400 €: 142.82 €: 1 : 197 mm: 4 mm: 2 mm: 20 1/min: 90 °: 4 kW: 890 mm: 780 mm: 1115 mm: 550 kgHydraulic driveAutomatic adjustment of the blade gap2 downholder2 gauges angle adjustableProtection cover, acrylic glassFoot pedalWaste boxAccording to ",CE", regulations User manual in English or GermanThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: ca. 12 - 14 Wochen ab Auf : Türkei : 21400 €: 5 mm: 1200 mm: 4,1 m/min: 3000 mm: 750 mm: 1400 mm: 1350 kg: 250 / 2000 mm: 300 mmMobile control panelHydraulic clamp on centerGearbox motor with brakeMotorized sheet centering systemInside cutting systemAccording to EC safety regulationsOperating manualOptional equipment (prices on request): 1 spare blade set Flanging attachment with 1 set rollsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 8 Wochen ab Auftragse : Italien : 14020 €: 269.18 €: 76 mm: 370 mm: 680 mm: 910 mm: 193 kg: 15 cm³: 76 x 3 mm: 2 x 5,4 mm: 76 x 3 mm: 70 x 4 mm: 76 x 1,6 mm: 76 x 4 mm: 76 x 6 mm: 76 x 6 mm: 76,3 x 3,25 mm: 50 x 4 mm: 45 mm: 75 x 15 stehend, 75 x 30 mm: 380 mm: 10 mm: 10 mm: 1/2 U/min: 3.5 kWdigital display of bendmaterial spring back compensationquick-change tooling system2 hexagonal tool holders (40 and 50 mmaccurate counterbending die positioningfoot pedalusers manualtools not includedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.