Manufacturer:
(Category: 1300)
Pipe conveyor screw with 270 mm diameter and 5,000 mm conveyor length (measured from center inlet to middle outlet). Drive 5.5 kW via intermediate gearboxes of gearbox construction north and claw coupling. Tree speed: 49 UPM; Spiral pitch: 130 mm. ... more information
Pipe conveyor screw with 270 mm diameter and 2,900 mm conveyor length (measured from center inlet to middle outlet). Drive 5.5 kW via intermediate gearboxes of gearbox construction north and claw coupling. Tree speed: 49 UPM; Spiral pitch: 130 mm. ... more information
Stainless steel pipe screw with 250 mm diameter and 2,100 mm conveyor length (measured from mid inlet to middle outlet), inlet and outlet 270 mm each, with drive via intermediate gearbox and claw coupling. ... more information
Electro-mechanical scale for liquids, with Hottinger load cell, pressure control valve, pneumatic outlet valve and solenoid valve. In support frame with feet. ... more information
Totalent emptyer with hydraulically operated floor flaps over the entire length, drive 37 kW via Flender gearbox, incl. hydraulic unit with 4 kW for actuating the floor flaps and pneumatic flaps for filling from above. The micl is occupied with Becker shovels, the mixer has three flanges for retrofitting knife heads / choppers. Mixer, drive unit and hydraulic unit are mounted on a stable base frame; The scope of delivery also includes another frame for spring-supported vibration reduction.
Gross bar scale for filling open bags from 10 - 50 kg, with feed paddle screw incl. drive 1.1 kW for coarse and fine current dosing, with pneumatic sack clamp (200 mm) and automatic bag drop, mounted on an elastic stand frame. Last used for the filling of construction chemical products; good condition, last calibration in 2014.
Electro-mechanical scale for fluids, with Hottinger load cell, pressure valve, pneumatically operated slide valve and magnet valve. In base frame / stand. ... more information
Totalentleerer mit hydraulisch betätigten Bodenklappen Single-shaft ploughshare mixer with hydraulically perated discharging flaps (full length engagement), incl. 4 kW hydraulics aggregate for operating bottom flaps and pneumatic flaps om top for feeding. Mixer shaft is equipped wirh Becker shovels, mixer has 3 mounts for retrofitting choppers. Mixer, drive unit and hydraulics aggregate are mounted on solid base frame; included in scope of supply: Second base frame with spring-based vibration reduction system.
Batch horizontal mixer in standard steel version, lined inside with carbide, useful filling up to approx. 800 l.. Drive over 37 kW motor, Flender head gear and start-up clutch, equipped with 2 flanges for optional knife heads / choppers. Slingshot shaft with armoured Becker shovels (as good as new). Incl. basic frame for mixer, gearbox, fluid coupling and motor. Sandblasted and repainted.
Beam balance bagging installation for filling open bags from 10 - 50 kg, with feeding screw (inkl. Paddles and 1,1 kW drive) for fine and coarse dosing, with pneumatically operated bag clamp (Ø 200 mm) and automatic bag drop function, mounted in base frame. Prior use: Bagging construction chemicals (dry mortar etc.); in good condition, last calibration in 2014.
Low pressure blower GMB 14.8, Y.O.M. 1994, with 11.8 m3/min. volume flow at delta-P = 360 mbar, P1 = 0.64 bar. Drive 44 kW / 1.485 UPM, with check valve, overpressure valve, tank, air filter, base and sound insulation hood. ... more information
Low-pressure blower GMB 14.8, built 1994, with 11,8 m³/min. volume stream at delta-P = 360 mbar, P1 = 0,64 bar. 44 kW / 1.485 RPM drive, with flow check valve, pressure-limiting valve, tank, air filter, base frame and sound insulation hood. ... more information
Spur gear with drive motor 30 kW (e.g. suitable for a ball mill), shaft diameter 45 mm, N1 = 1,450 UPM, N2 = 14.5 UPM, drive shaft diameter 130 mm, with electric brake, coupling with counter window 600 mm diameter. Oil 190 CSX/50C - Wa-No. 369226. Complete on foundation frame. ... more information
Parallel shaft gear with e-drive 30 kW (e.g. for use with a ball mill), motor shaft diameter 45 mm, N1 = 1.450 RPM, N2 = 14,5 RPM, drive shaft diameter 130 mm, with electrical brake, clutch with counter disc 600 mm diameter. Oil 190 CSX/50°C - Wa-No. 369226. Complete on base frame. ... more information
Type: VK 1056, Y.O.M. 2006. Single-deck rod sizer with integrated feed channel, rod carrier and rod rake made of stainless steel, screen frame rubberized 60 shore, 2 unbalance motors 2.8 kW / 960 UPM, open screen box on compression springs, brake control, steel base. Current cutting at 8 mm; machine was only in use for 12 months, therefore in very good condition.
Type: VK 1056, built 2006. Single deck vibratory bar sizer with integrated feeding chute, bar mount and bar rakes in stainless steel, screen frame rubber lined 60° shore, 2 imbalance drives 2,8 kW / 960 RPM, open screen frame on coils, break control, steel construction. Current parting cut at 8 mm; Sizer has only been running for 12 months, therefore it is in very good condition.
Pressureless dust filters for mounting on silos, material bunkers, etc. in standard steel version. Equipped with 20 pcs. fabric filter hoses (200 mm x 2,000 mm long each), incl. electric vibro cleaning. Filter area: Approx. 25 m2. In very good condition, several filters available (same construction).
Stainless steel vibrating sieve for wet sieving, 1 deck with 915 mm, 2 outlets, with unbalance drive (approx. 1 kW) and springs. 2 pcs. available. ... more information
Vibrating sieve for wet screening, 1 deck with 915 mm (36) Ø, 2 outlets, with imbalance drive (ca. 1 kW) and springs. 2 pcs availabe. ... more information
Mogensen twin-sizer with 4 decks (each deck has 2 screen gauzes with a sieving area of 1,32 m x 0,98 m per gauze) and 4 outlets. Incl. 2 imbalance drives (4,0 kW / 380 V each), meshes, covers and supporting springs. Since sieve has a central division wall two separate material streams can be fed (after corresponding adaptation of the outlet hoppers).