presses used for sale

Koller sleeves punched for CPM 22-2.5  ... more information

Graf Koller sleeves punched for CPM 16-2.5 Pelletier press  ... more information

Graf Kollerhülsen Geriffelt to CPM Pelletpress  ... more information

Koller sleeves Geriffelt for CPM 22-2.5  ... more information

In 2007 Floor press from BÃ?TFERING, type 4 H 100,. Lower piston design Pressing area of 1250 x 2200 mm Aluminium plates electrically heated Total pressure of 100 to Operating pressure 320 bar spec. Pressure 3.5 kg/cm2 with full interpretation spec. Pressure at 80% design 4.5 kg / cm2 Hydraulic power 380 volts, 50 Hz, 1.5 kW Press plates: 2 piece ELKOM electric heating Panel solid hard aluminum in the thermally stable sandwich construction for temperature applications up to 200 ° C 2200 x 1250 x 18 mm + 19 mm Mono Lux + 19 mm V 100 insulation plate 17,500 Watts, 400 volts, 3 Ph. Surface smooth, flat, screw-free, gold anodized Plate construction hides more-row from the bottom screwed maximum continuous temperature 200 ° C incl. 2 piece cooling plate in Sandwitchbauweise. This is mounted below the insulation. The heatsink must be with a cold ...

pressure: 40 tdistance between columns: 700 mmstroke: 150 mmtable surface area: 700x650 mmram surface: 670x650 mmhole in the table: Ø 120 mmtable height: 850 mmweight of the machine ca.: 4 tdimensions of the machine ca.: BxTxH 2000x18000x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 100 tdistance between columns: 625 mmstroke: 150 mmtable surface area: 580x450 mmram surface: 580x340 mmhole in the table: Ø 150 mmtable height: 850 mmtool hole in ram: Ø 45 mmcolumn travel -side: 200x200 mmweight of the machine ca.: ca. 6,0 tdimensions of the machine ca.: BxTxH ca. 1300x1300x2750 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 250 tdistance between columns: 1100 mmstroke: 400 mmdayligth: 600 mmtable surface area: 1000x800 mmram surface: 1000x800 mmtable height: 950 mmtotal power requirement: 65 kWweight of the machine ca.: 25 tdimensions of the machine ca.: BxTxH 0000x0000x3900mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 250 tdistance between columns: 850 mmstroke: 500 mmdayligth: 800 mmtable surface area: 800x800 mmram surface: 800x800 mmweight of the machine ca.: 12 tdimensions of the machine ca.: BxTxH 1600x1600x3400 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 25 tdistance between columns: 800 mmstroke: 100 mmdayligth: 450 mmtable surface area: 750x750 mmweight of the machine ca.: 3 tdimensions of the machine ca.: 1500x1500x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... more information

pressure: 60 tthroat: 330 mmstroke: 500 mmtable surface area: 640x640 mmram surface: Ø 120 mmtable height: 850 mmtool hole in ram: Ø 50 mmweight of the machine ca.: 7 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... more information

pressure: 100 tthroat: 275 mmstroke: 150 mmtable surface area: 860x550 mmram surface: 600x400 mmtable height: 810 mmtool hole in ram: Ø 50 mmdayligth: max. 475 mmweight of the machine ca.: 7 tdimensions of the machine ca.: BxTxH 2000x2500x3300 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 250 tdistance between columns: 900 mmstroke: 300 mmtable surface area: 850x900 mmram surface: 800x880 mmstroke: 300 mmtable height: 1050 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... more information

Plate dimensions: 1550 x 850 mmDaylight opening: 350 mmNumber of daylights: 1 St.Heating: ja Total pressure: 60 toMotor output: kWDimensions (L/W/H): 2,3 x 0,85 x 1,73 mmweight of the machine ca.: 2,5 tElectric 380 Volt: Hydraulic veneer- or board press with printing capacity of 80 t, shutdown when the final pressure output is reached and heating in the lower/upper plate.Machine dealer with own stock of 1600 m².The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 200 tpassage width: 2122 mmtable surface area: 2100 x 1400 mmtotal power requirement: 60 kWweight of the machine ca.: 35 tdimensions of the machine ca.: mPress/punch with injection molding unit200 ton punch upstroke press with injection molding machine (400to)Additional guard locking via 4 power strokesManufacturer: R+S TechnikYear of construction: 2013 / rebuild 2016Mains voltage/frequency: 400V/50Hz 3~(N/PEConnected load: 60KWWeight about 35000kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Workpiece dimensions: 2.500 x 1.300 x 500 mmSpecific pressure: 0,9 kg/cm²total power requirement: 25 kwmax. temperature: 140 Grad: 100 m³/hWeight: 1.550 kgDimensions (L/W/H): 3.330 x 1.860 x 1.950 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... more information

Working width: 4000 mmWorking height: 2600 mmNumber of cylinders: 6 St.weight: 2000 kgDimensions (L/W/H): 5550x1300x3000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... more information

Working width: 3500 mmWorking height: 2300 mmNumber of cylinders: 4 St.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... more information

Working width: 3500 mmWorking height: 2300 mmNumber of cylinders: 4 St.Stable frame welded construction of thick-walledSpecial hollow profiles , sliding table and pressure beam with50 mm hole pattern .On the left side continuous abutment for grouting the wide ,lower abutment in 2 levels.Vertical pressing cylinder on specialty bar with one-quick adjustment with weight compensation in the 50 mm hole patternadjustable in height. Long sliding table ensure thecontinuous recording of high jacking forces .Fast, smooth width adjustment with ball bearingCarriage with central fixation in 50 mm hole pattern.Upper horizontal press cylinder infinitely adjustable in height andequipped with counterbalance .Lower horizontal pressing cylinders with bore fortwo abutments levels without weight compensation .Abutment and pressure plate depth 100 mmMachine controlled electro -hydraulic with 2 pieces vertical ...

Working width: 3500 mmWorking height: 2650 mmNumber of cylinders: nach Wahl St.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... more information