other metal working machines used for sale

Ultrasonic cleaner GT85 GT 2000-3P built in 2008. The washing tub is made of 316L stainless steel, the other tubs are made of 304 stainless steel and the supporting structure is made of structural steel. The volume of washed products should not exceed (LxWxH) 2400 x 600 x 600 mm Industrial washer - technical data: - external dimensions (LxWxH): 6400 x 4400 x 2800 mm - usable dimensions: chamber I (washing and phosphatizing): 2800 x 800 x 900 mm - useful dimensions: chamber II (rinsing): 2800 x 800 x 900 mm - usable dimensions: chamber III (drying): 2800 x 800 x 900 mm - power consumption: 63 kW - total weight: 2500 kg Bathtub 1: - preparation type: Ruster P02, Roklin P11 - pH: 2-4 - bath operating temperature: 20-60 degrees C - total bath capacity: 2000 l - maximum product weight: 500 kg - maximum product volume: 250 dm3 Bathtub 2: - type of preparation: tap water  ...

The CIMAT CMT 30 V2 balancing machine was manufactured in 2015 in Poland. Bvcilkrj7m Basic technical data: - software: ROTOTEST - component weight: 0.2 to 30 kg - maximum rotor diameter: 400 mm - maximum rotor height: up to 200 mm - compressed air pressure: 0.6 MPa - balancing machine dimensions: 1200 x 1200 x 1500 mm - control panel dimensions: 600 x 600 x 1800 mm - weight: 500 kg

ERMAKSAN LASERMAK 6000 6X2 laser cutter was produced in 2014. Technical parameters: – laser source: 6000 W CO2-laser GE Fanuc C6000i-Model C – RF-excitation: 2 MHz – power stability: ± 2% (power monitor) – laser wave length: 10.6 μM – beam mode: Fanuc Low Order Mode – laser shutter: mechanical safety shutter – laser gas composition: CO2 / He / N2 – gas consumption by laser: 20 l / h – cooling water flow rate: 250 l / min – maximum cutting capacity: mild steel 25 mm (during tests the maximum achieved: 30 mm), stainless steel 15 mm, aluminum 12 mm - machine activation time: 22899 h - working time: 10122 h - cutting time: 8429 h – total energy requirement: 100-120 kW – cutting head focal length: 5 -7” -10 inch – maximum worksheet size: 6150 x 2000 mm – maximum burden capacity: 4000 kg – machine axes: 5 axes [X, Y, Z, U (X2), V] – axis ...

Gabion Mesh Production Line HEBEI ANPING WIRE MESH MACHINE FAKTORY 60X80 / 4300 was built in 2013. Machine for the production of hexagonal gabion mesh with the following parameters: - manufacturer: Hebei Anping Wire Mesh Machine Faktory (China) - mesh size: 60 x 80 mm or 60 x 100 mm - maximum width of the produced mesh: 4300 mm - wire diameter: 2.0-2.8 mm - capacity: up to 2.5 m / min - machine weight: 18 tons - engine power: 22 kW

Offer via gebr. Thread cutting machine with pipe saw RA21 Made GEORG FISCHER type KM2, built 1997 Technical data: Thread diameter 3/8" - 2" Power connection 200 - 240 V / 50 Hz With mobile undercarriage with threaded cutting jaws 3/8", 1/2", 3/4", 1", 11/4", 11/2",2" used, in good condition.

Used nipple holders Nipple holder with internal voltage, up to 2", self-exciting  ... more information

Spraying cleaning system from GT85 TYPE: 0227 TARRA Smart 900 MPS, weight 2300 kg  ... more information

Zubehoer: filter system with pump control cabinet The machine is equipped with a Hirschmann deflection head, H 1.2 system, Orbi-Cut System 3 R  ... more information

Fully functional FARO Arm Measuring Arm Prime High Precision 3D Measuring Instrument Quality Control Year of construction: December 2012 Certification date: August 2014 Number: R04-02-12-28398 Single Point: 0.016 mm Volumetric: +/- 0.023 mm Made in Germany The Best Portable Coordinate Machine (CMM) High Measurement Accuracy, Measurement Stability Reduced inspection times, automatically generates reports Ready to use in a few seconds Measure parts and assemblies quickly, easily and precisely Ideal for complex measurement tasks Solid measuring plate with trolley table, 336 kg Drawer with key Degree of accuracy: DIN 876/1 Permissible deviation: 0.02 mm Actual deviation: 0.00589 mm Checked on 05.03.2013 Made in Germany With various accessories Measuring arm case HP PC Tower Screen Keyboard Lots of software e.g. Cam2 Measure 10, Nvidia Graphics, Windows, HP

Used packing machine, built in 1998, with heat shrink tunnel furnace thermoshrinker HV 401, built in 1998. Parcel sizes width approx. 350 mm " Height approx. 150 mm " Length of approx. 50-3000 mm (intermediate bench required)  ... more information

Space requirement: 11300 3950 2800 mm Object table: 5000 mm Sled movement: 2350 mm Permeability between columns: 1260 mm Machine weight: approx. 20t  ... more information

Open spray level 2x2.1x2.2 The overspray in powdering is absorbed via the suction unit. The powder spray stand is delivered on rollers and is thus mobile. - The suction is equipped with a 60 L powder container (rollbar). - The first stage is 4 filters in the suction system. - Above the cabin is the Absolute filter. 1. Dimensions of the powder level width 2,000 mm Depth 2,100 mm Height 2,200 mm 2. Fan 1 pc. 6,000 m3/h Electric motor 3.0 kW 3. Filter 325x600 4 pcs. Type Filter cartridges 4. Electromagnetic valves 2 pcs. 1" "Turbo" Italy 5. Absolute filter 1 pc. type pocket filter

Powder incineration furnace 2,000 x 1,900 x 2,000 mm 1 inner dimension length 2,000 mm 2 Inner dimension width 1,900 mm 3 Inner dimension height 2,000 mm 4 Substructure 1 set steel profile 5 walls 1 set on both sides galvanized sheets 1mm, outside RAL 6 insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m2 7 ground furnace gets 2 entry rails for horde wagons 8 Temperature 220°C 9 fans 1 pc. 5,700 m3/hr 10 Electric motors 1 pc. 2.2 kW , 1450 R/m, 3 F, 50 Hz 11 Thermal power 33 kW = 28,380 kcal/hr 12 sash doors on one side 2 pcs insulated with rock wool 100mm 75Kg/m2 Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX with heat-resistant fans and heat-resistant bearings, Thermoblock has overheat protection 14 Burner 1 pc. furnace is operated with gas burner 15 Exhaust air 1 pc. device for exhaust air pipe, manual flap guide

Powder incineration furnace 2,000 x 1,900 x 2,000 mm 1 inner dimension length 2,000 mm 2 Inner dimension width 1,900 mm 3 Inner dimension height 2,000 mm 4 Substructure 1 set steel profile 5 walls 1 set on both sides galvanized sheets 1mm, outside RAL 6 insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m2 7 ground furnace gets 2 entry rails for horde wagons 8 Temperature 220°C 9 fans 1 pc. 5,700 m3/hr 10 Electric motors 1 pc. 2.2 kW , 1450 R/m, 3 F, 50 Hz 11 Thermal power 33 kW = 28,380 kcal/hr 12 sash doors on one side 2 pcs insulated with rock wool 100mm 75Kg/m2 Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX with heat-resistant fans and heat-resistant bearings, Thermoblock has overheat protection 14 Burner 1 pc. furnace is operated with gas burner 15 Exhaust air 1 pc. device for exhaust air pipe, manual flap guide

Powder incineration oven 3,500 x 1,900 x 2,000 mm electric 1 inner dimension length 3,500 mm 2 Inner dimension width 1,900 mm 3 Inner dimension height 2,000 mm 4 Substructure 1 set steel profile 5 walls 1 set on both sides galvanized sheets 1mm, outside RAL 6 insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m2 7 ground furnace gets 2 entry rails for horde wagons 8 Temperature 220°C 9 fans 1 pc. 7,500 m3/hr 10 Electric motors 1 pcs. 3 kW , 1450 R/m, 3 F, 50 Hz 11 Thermal power 58 kW 12 sash doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m2 Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heating electrically heat-resistant fans and heat-resistant bearings, thermoblock has overheat protection 14 Burner 1 pc. oven is electrically heated 15 Exhaust air 1 pc. device for exhaust air pipe, manual flap guide

Powder incineration furnace 3,500 x 1,900 x 2,000 mm gas operation 1 inner dimension length 3,500 mm 2 Inner dimension width 1,900 mm 3 Inner dimension height 2,000 mm 4 Substructure 1 set steel profile 5 walls 1 set on both sides galvanized sheets 1mm, outside RAL 6 insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m2 7 ground furnace gets 2 entry rails for horde wagons 8 Temperature 220°C 9 fans 1 pc. 7,500 m3/hr 10 Electric motors 1 pcs. 3 kW , 1450 R/m, 3 F, 50 Hz 11 Thermal power 58 kW = 49,880 kcal/hr 12 sash doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m2 Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX with heat-resistant fans and heat-resistant bearings, Thermoblock has overheat protection 14 burner 1 pc. oven is heated with gas burner. 15 Exhaust air 1 pc. device for exhaust air pipe, manual flap guide

Powder incineration oven 4,500 x 1,900 x 2,000 mm electric 1 inner dimension length 4,500 mm 2 Inner dimension width 1,900 mm 3 Inner dimension height 2,000 mm 4 Substructure 1 set steel profile 5 walls 1 set on both sides galvanized sheets 1mm, outside RAL 6 insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m2 7 ground furnace gets 2 entry rails for horde wagons 8 Temperature 220°C 9 fans 2 pcs. 2x 5,700 = 11,400 m3/hr 10 Electric motors 2 pcs. 2x 2.2 kW , 1450 R/m, 3 F, 50 Hz 11 Thermal power 74 kW 12 sash doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m2 Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heating electrically heat-resistant fans and heat-resistant bearings, thermoblock has overheat protection 14 Burner 1 pc. oven is electrically heated 15 Exhaust air 1 pc. device for exhaust air pipe, manual f ...

Compact machine system for the production of stamped and bent parts made of strip and wire. Tool quick clamping system for shortest set-up times User-friendly machine and process control P CNC 4E Compatibility with RM 35, RM40 and RM4 tools Item condition: very good You purchase the machine as it can be seen in the pictures. The punch bending machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines

Schroeder & Bauer WB 32-1 Universal wire and belt bending machine Wire feed Plain text display Press force monitoring Wire straightener Bosch stripping devices Bracket and brush motor with mounted tool W32/1-32 Soundproof cabin Fäßer CU wire with stamped parts Switchboard Item condition: very good Description of the manufacturer, deviations possible. You purchase the machine as it can be seen in the pictures. The punch bending machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines

Schroeder & Bauer WB 32-1 Universal wire and belt bending machine Wire feed Plain text display Press force monitoring Wire straightener Bosch stripping devices Bracket and brush motor with mounted tool W32/1-32 Soundproof cabin Fäßerb CU wire with stamped parts Switchboard Item condition: very good Description of the manufacturer, deviations possible. You purchase the machine as it can be seen in the pictures. The punch bending machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines