subcategorias
(terceiro nível de categoria)
Fabricante:
(Categoria: 103)
module: 1,0 mmtool taper: MK 3 turning speeds: von 169 bis 2500 U/min.: distance: Fräser-Werkstück: 10 - 50 mmweight: je Stück: 500 kgdocumentation: vorhanden number: 8 Stück: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... mais informação
x-travel: 1100 mmy-travel: 700 mmz-travel: 550 mmtable surface area: 1435 x 460 mmspindle taper: SK 40 spindle turning speed range: 30 - 2066 U/minfeed - longitudinal/cross: 14 - 820 mm/minfeeds vertical: 7 - 410 mm/minrapid motion -longitudinal/cross/vertical: 11 / 11 / 5,5 m/mintotal power requirement: kWweight of the machine ca.: 3,5 tdimensions of machine L x W x H: 2,16 x 2,46 x 1,89 mAccessories: coolantThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Collet set 15 pieces with drill chuck Vertical Drilling and Milling Head - T-Slot Width 12 mm Cutter head Coolant Setup x - travel 500 mm y - travel 200 mm z - travel 400 mm Feed: 5.6 - 238 mm/min with quill stroke Speed: 35.5 - 1800 rpm with rapid traverse Clamping area: 800 x 300 mm Total power requirement 16 A Spindle holder ISA 40 Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out.
x-travel: 700 mmy-travel: 225 mmz-travel: 400 mmturning speed range - horizontal: 45 - 1800 U/mintaper MK: SK40 table surface area: 1000 x 300 mmtotal power requirement: 3,8 kWweight of the machine ca.: 1,75 tdimensions of the machine ca.: 1,3 x 1,7 x 1,8 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 8000 mmy-travel: 920 mmz-travel: 1000 mmControl: total power requirement: kWweight of the machine ca.: 30 tdimensions of the machine ca.: mYear of construction approx. 1970X 8000mmY 920mmZ 1000 mmHead rotates 180°TableLength 3600mmWidth 920mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 3000 mmy-travel: 1350 mmz-travel: 1400 mmspindle taper ISO: 50 turning speeds: 22-1400 U/minRotary table: 800x600 mmTable dimensions: 2500x1200 mmFeed: 5-3000 mm/mintotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 19000 mmy-travel: 7600 mmz-travel: 2000 mmw-axis: 5000 mmtable surface area: 18500 x 5000 mmtable load: max. 500 tdistance between columns: 5500 mmpower capacity - milling spindle: 110 kWtool taper: CAT #60 Control: FANUC 15i MB total power requirement: - kWweight of the machine ca.: 650 tdimensions of the machine ca.: - mOverhauled & modernized in 2007equipped with:- CNC control FANUC 15i MB- 5 headsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel:1000 mmy-travel:480 mmz-travel:480 mmtable width:315 mmtable length:1250 mmtable - longitudinal motion:1000 mm:1250 x 315 mmturning speed range:28 - 1400 U/minpower capacity:3,7/4,4 kWtotal power requirement:6 kWweight of the machine ca.:2800 kg100 % before loadingwarranty:noneone used knee and column milling machine-universal, make UNION Bielefeld, type USF 4, Baujahr 1970, Maschinen-Nr. 55/214
power capacity: 0 kWtool adaptor: 0 total power requirement: 0 kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... mais informação
x-travel: 800 mmy-travel: 300 mmz-travel: 400 mmtool taper: SK 40 fixed table: 400 x 1000 mmaddition table: 260 x 1000 mmturning speed range: 40 - 2000 U/minfeed range: 10 - 500 mm/mintotal power requirement: 3 kWweight of the machine ca.: 2000 kgdimensions of the machine ca.: 1775/1880/1850 mm• fixed angle table,• 3-axis-digital display ACU-RITE• 5 tool tapers,The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Milling machine MACMOM M 100, year of construction 1970. Without table. At call. ... mais informação
Turret milling machine Brand: HESSAPP (Made in Germany) Model: HC-50et Year: 1970 Description: - Table length: 1180x330mm - Spindle turning speeds: 70 - 6000rpm - X axis travel length: 600mm - Y axis travel length: 350mm - Z axis travel length: 500mm ... mais informação
Weight: approx 2 t. dimensios: 1 x 1 x 1,5m ... mais informação
1 x Universall tool-feeding machine Lid FP 4 Built: c.1970 Very robust and rare conventional machine in good condition. Technical data: Travel: X: 700 Y: 400 Z: 450 mm Spindle speeds: 31.5 - 1,600 rpm (18 levels) Tool holder: ISO 40 Pinole stroke: 115 mm Feed in X/Y/Z Feed range: X/Y/Z 5 - 500 mm/min (infinitely adjustable) Rapid response: X/Y: 10 - 500 mm/min Z: 5 -250 mm/min (18 levels) swivel handling table Clamping area: 860 x 500 mm Accessories: 1 x horizontal counter bearing 5 x horizontal frond spine Bftj7cazem 10 x vertical fraes aufnahme 36 x tension tension ingesheis from 0.5 - 18 mm 0.5 mm rising 5 x Direct clamping pliers D: 12/14/16/18/20 mm 1 x machine vice Manual various distance rings and accessories for milling machines complete documentation The machine can be inspected at our warehouse under electricity. A 3-axis digital ...
Characteristics: Mobile gantry milling machine, serial number Work Area: 6300 X 2400 X 600 (Max Stroke) Max Work Feed: 2000 mm/min Max Rapid Feed: 4000 mm/min Accessories: Nose: Max RPM: 2000 Manually positioned head Control: Heidenhain (Atek Hs Plus ... mais informação
x-travel: 2000 mmy-travel: 1000 mmz-travel: 1000 mmControl: Heidenhain type: TNC 430 : spindle turning speed range: 15-1450 U/minTable area: 2300x1200 mmSpindle: 200 mmspindle stroke: 200 mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mNr 3762Maschine wurde überholtmachine is retofitThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Table dimensions: 300x1100mm, length: 1770mm, width: 1500mm, height: 2050mm, weight: 2.2t, an inspection is possible. ... mais informação
Description: travel lengthwise 350mm rapid traverse lengthwise feeds 12,5 - 140 mm/min table 785x200mm speeds 35,5 - 1800/minApprox. Onsite Dimension. (l x w x h): 0 x 0 x 0 mm, weight approx.: 0 kg ... mais informação
Universal milling machine Macmon M200 (comparable to Deckel FP3) Built in 1971 Machine no. 628/2 X-axis travel 600 mm Travel Y-axis 310 mm Z-axis travel 390 mm Speed range 37-1900 rpm Feed in 3 axes from 7-380 mm/min Rapid traverse in all 3 axes Vertical & Horizontal Spindle Vertical quill and horizontal quill extendable - SK-40 Tightening system S20x2 Rigid clamping table Coolant system Operating instructions 3-axis Fagor digital display (X scale counts twice) The machine has been technically tested and is fully functional. Spindle concentricity 0.002mm Reversing clearance X-axis 0.75mm Reversal clearance Y-axis 0.7mm Reversal clearance Z-axis 0.2mm Footprint LxW: 1500x1500mm Weight approx. 1500kg
Table size: 254 x 1100 mm Table movement x: machine. u. v. hand 682 mm Table movement y: hand 380 mm Table movement z: hand 457 mm Milling head swiveling to: +/-90 or +/-45 ° Spindle retainer: ISO 40 Spindle speeds: 70-2300 rpm Quill feeds: 0.038 â 0.152 mm / min Spindle drive: 380 V, 2.2 kW Space: 1600 x 1600 x 2150 mm Weight: 1420 kg