Fabricante:
(Categoria: 1300)
Note: The images serve to illustrate the material. - The workbench racks are picked unassembled; - The production time is usually about 3 - 5 working days. Basic dimensions: Width: approx. 3,200 mm Height: approx. 940 mm Depth: approx. 850 mm The scope of delivery includes: 04x Square tube, used Material colour: sendzimir galvanized Profile height: approx. 900 mm Square profile: 140 x 140 x 4 mm Drill hole spacing: 75 x 50 mm Drill hole Ø: 13 mm 02x CS Sigma Profile, used Material colour: sendzimir galvanized CS-Sigma profile: approx. 300 x 85 x 28 x 15 mm Material thickness: 2 mm Profile length: approx. 2,900 mm 02x CS Sigma Profile, used Material colour: sendzimir galvanized CS-Sigma profile: approx. 300 x 85 x 28 x 15 mm Material thickness: 2 mm Profile length: approx. 550 mm 01x Particleboard, used Chipboard thickness: 38 mm Chipboard width: ap ...
Note: The images serve to illustrate the material. - The workbench racks are picked unassembled; - The production time is usually about 3 - 5 working days. Basic dimensions: Width: approx. 2,750 mm Height: approx. 940 mm Depth: approx. 850 mm The scope of delivery includes: 04x Square tube, used Material colour: sendzimir galvanized Profile height: approx. 900 mm Square profile: 140 x 140 x 4 mm Drill hole spacing: 75 x 50 mm Drill hole Ø: 13 mm 02x CS Sigma Profile, used Material colour: sendzimir galvanized CS-Sigma profile: approx. 300 x 85 x 28 x 15 mm Material thickness: 2 mm Profile length: approx. 2,450 mm 02x CS Sigma Profile, used Material colour: sendzimir galvanized CS-Sigma profile: approx. 300 x 85 x 28 x 15 mm Material thickness: 2 mm Profile length: approx. 550 mm 01x Particleboard, used Chipboard thickness: 38 mm Chipboard width: ap ...
Note: The images serve to illustrate the material. - The workbench racks are picked unassembled; - The production time is usually about 3 - 5 working days. Basic dimensions: Width: approx. 5,950 mm Height: approx. 940 mm Depth: approx. 850 mm The scope of delivery includes: 04x Square tube, used Material colour: sendzimir galvanized Profile height: approx. 900 mm Square profile: 140 x 140 x 4 mm Drill hole spacing: 75 x 50 mm Drill hole Ø: 13 mm 02x CS Sigma Profile, used Material colour: sendzimir galvanized CS-Sigma profile: approx. 300 x 85 x 28 x 15 mm Material thickness: 2 mm Profile length: approx. 5,650 mm 02x CS Sigma Profile, used Material colour: sendzimir galvanized CS-Sigma profile: approx. 300 x 85 x 28 x 15 mm Material thickness: 2 mm Profile length: approx. 550 mm 01x Particleboard, used Chipboard thickness: 38 mm Chipboard width: ap ...
A pile cutter from IDEAL 3915-95 with base frame is offered. The pile cutter is used Year of manufacture 2004 and in very good condition with accessories. The machine has no faults whatsoever and works perfectly. Electrical connection: 230 V / 50 Hz / 1~ Motor power: 0.45 kW Dimensions: W 600 x D 695 mm x height 1070 mm Weight: approx. 80 kg Technical data processing: Cutting length: 390 mm Insert height: 40 mm Remaining cut: 35 mm Insertion depth: 390 mm Accessories 3 spare knives and 4 pressure strips VAT can be shown on the invoice, collection must be organized by the buyer
TO WHOM IT MAY CONCERN; WE VE 6 PCS USED WOODWARD 721 DIGITAL SPEED CONTROL AT OUR STOCK. WE DISMANTLED THOSE CARDS FROM RUNNING SYSTEM. PLS FIND DETAIL ON BELOW PART NO 8280 - 303 PART NO 9987 - 206 CTRL ASSY 8237 - 951 REV. E CTRL ASSY 8237 - 735 REV. G ALL PANES LOCATED IZMIR TURKEY . READY TO SHIPMENT. IF YOU'VE ANY FURTHER QUESTIONS PLS DO NOT HESITATE TO CONTACT WITH US . Capt. Ayhan Ugurluba Best Regards ; Aliaga Marine Services E mail: info/aliagamarine.com Phn/Fax:+90 232 618 03 90 Mobile: +905556084850 aliagamarine.com TURKEY
Fluke Biomedical ESA 615 Electrical Safety Analyzer - matr 4736047. ... mais informação
Offer up to 2 plasma power supplies here. Technical data, as shown in the picture. ... mais informação
Lauda ITH150 / 6KW heat transfer system LSI 51337 circulator 20 - 350°C. The plant was dismantled during operation. The insulated metal flexible hoses come along. They have 12mm Swagelok clamping ring fittings. The original description for all relevant components and the system itself is part of the delivery.
Glass Heating Equipment Furnace GT1411 Equipment application. This special equipment is used for heating homogenously the flat glass and cooling it thereafter, is involved in the glass deep processing machinery. The suitable working glass is clear float glass. Power supply requirement and total weight of equipment. This kind of equipment requires a 3-phase-5-line AC power supply of 380V and total installed power of it is about 250kW. Total weight is about 10 tons. Constitution of Glass Heating Equipment. Computer, control cabinet, power regulation cabinet, loading table, heating section, coating section, annealing section, unloading table. The Furnace was in good operational condition when it was dismantled in 2016. The unit is located in a warehouse in Finland
Infeed and Outfeed roller conveyor transport system for material lengths 2.5-14m Entrance dimensions- 2100 x 600mm The machine can process a plate of 2000mm wide and min. 5mm thickness Transport weight of max 1000 kgm Number of Turbines- 6 Turbines of C-380 11 kW Turbine Power Average speed at BSa 2 12- 1-1.5 mmin Abrasive hopper with screw conveyor 2.2 kW Abrasive used- Round low carbon sheet shot or cut wire Buck elevator with a 5.5 KW gear motor and a broken belt detection sensor Machine with Brush blow off plant Machine equipped with screw conveyor Automatic height adjustment for the brush Automatic adjustment for the 4 outer turbines
The color shading in hardware consisting of automatic Auricolor SO tinting machine, large quantities of pasta to administer two LV-Dosing units, PC-based control unit, as well as equipment for intersections between lines. Shading equipment is made in accordance with the standards EN 50014 and EN 50016 and meets the explosion classification Eex p II T3. (The device is equipped with a fan, supply and exhaust pipes and pressure sensor to achieve a permanent vacuum supply to the pipe and well-ventilated.) 1 pack of Tinting Station LV-S18519 -contains 10 pieces 20-liter and 10 liter stainless steel tanks for 15 -the pump return 0.8 litres/min -Automatic nozzle shut-off -ohjauchoiceroniikka SA801, SA903 and SA704 2 x LV-Dosing units with frame structure -tank capacity 150 litres -pasta HL4625, 0.37 kW pump VIKING – approx. 5 l/min, Eex rated -Blade mixer helical motor, inverter ...
Belt conveyor 150x420cm This industrial conveyor features a robust belt with a width of 150 cm and a length of 420 cm, making it ideal for large-scale material handling operations. It is perfect for use in sectors such as manufacturing, logistics, and warehousing, If you need more specific details, feel free to ask!
Belt conveyor 150x420cm This industrial conveyor features a robust belt with a width of 150 cm and a length of 330 cm, making it ideal for large-scale material handling operations. It is perfect for use in sectors such as manufacturing, logistics, and warehousing, where efficient and reliable transportation of goods is essential. If you need more specific details, feel free to ask!
This is a used Kränzle high-pressure cleaner. The hot water is prepared electrically. It is installed stationary and is fully functional. It has a dosing unit for cleaning agents ... mais informação
Cutting table for 36 NF stones. There is equipment for formats 1.4 and 2.1. The cutter only in use for 5 months ... mais informação
Mobile compressor for the evacuation of natural gas from pipelines for maintenance and repair to offer. There are only few trucks of this worldwide. This truck is fully operational and used to be operated only by Gas Industryi n the past! For first details please refer to attached file. The truck is located in the north of Germany (between Bremen and Hanover). A visit is possible by appointment. Further details can be provided on request. - The machine has been completly refurbished in 2022 (documentation/ certification available -> see attached picture) - The truck/ machine is fully operational - Reason for replacement was the truck/ car body ( wanted to have a modern truck – nothing to do with compressor) - Current replacement price of compressor: around 4 Million EUR – delivery time around 36-40 months - Optionally we could provide an engineer from Gas Industry for machine ...
Drum washing machine for cleaning small parts (e.B screws or other small parts in electroplating) Drum diameter 630 mm, Heating medium: gas, power 180 kW, Temperature 50 - 70 °C, Air circulation 8,000 m³/h ... mais informação
We sell a used Inketsystem the type 273 e incl. linear axis for the set up mark Videojet ink jet eg. on a bottling line. The unit is used and in good condition with 2 Inkjetschläuchen and applicator heads. For questions we are available under 08071104277 ... mais informação