prensas usadas para la venta

used baler Manufacturer: PAAL Type: CPH 6540 Machine number: 29600 Year of construction: 2008 Main parts of the press: 1 automatic channel press 1 automatic lacing 1 hydraulic system 1 electrical control Press force at approx. 300 bar: 650 kN Duct cross-section (h x w): 75 x 100 cm Filling opening (l x w): 160 x 92 cm Number of binding wires: 4 pieces Power: - Wire pull: 3 kW - Twisting: 3 kW - Main drive pump: 75 kW Hydraulic oil tank volume: 2200 l Machine weight: approx. 14 t, depending on equipment Operating voltage: 3 x 400 VAC / 50 Hz / N / PE Press complete for continuous operation including: Machine design consisting of: - Pressure plate with roller guide mounted on the inside at the bottom, - Press box floor made of highly wear-resistant special steel, - replaceable, screwed running dies for the lower pr ...

automatic baler Manufacturer: PAAL Type: KONTI 275 D Year of construction: 2002 Operating hours: approx. 30,000 hours Main parts of the press: 1 automatic channel press 1 automatic lacing 1 hydraulic system 1 electrical control specifications: Press force: 75 t at 300 bar Specific pressing force: 9.09 kg/cm² Duct cross-section (h x w): 750 x 1,100 mm Filling opening: 1,020 x 1,550mm Number of binding wires: 4 pieces vertical Drive power: 1 x 75 kW Throughput: up to approx. 350 m³/h Hydraulic oil tank volume: 2,200 l Operating voltage: 3 x 400 VAC / 50 Hz / N / PE Other features: - Automatic cutting edge release - Large digit display for bale length and fault indication

automatic baler Manufacturer: PAAL Type: KONTI 275 C Year of construction 1996 specifications: Press force: 65 t Specific pressing force: 7.88 kg/cm² Channel format: 750 x 1,100 mm Bale weight: 450 - 600 kg, depending on material and bale length Filling opening: 1,550 x 1,020 mm Drive power: 45 + 30 kW Throughput: 380 m³/h Pressing capacity: - approx. 13.0 t/h at department store (35 kg/m³ bulk density) - approx. 23.0 t/h for mixed paper (60 kg/m³ bulk density) - approx. 35.0 t/h for collected goods (100 kg/m³ bulk density) Setting: 4-fold vertical Machine weight: approx. 21.0 t Optionally with feeding belt according to photos

automatic baler Manufacturer: PAAL Type: KONTI 200 C Year of construction: 1993 specifications: Press force: 50 t Channel format: 750 x 1,100 mm Specific pressing force: 6.06 kg/cm² Bale weight: 425 - 550 kg, depending on material and bale length Infill opening: 1,400 x 1,020 mm Drive power: 45 kW Throughput: 200 m³/h Pressing capacity: - approx. 7.35 t/h layered at department store (35 kg/m³ bulk density) - approx. 12.0 t/h for mixed paper (60 kg/m³ bulk density) - approx. 20.0 t/h for collected goods (100 kg/m³ bulk density) Setting: 4-fold vertical Machine weight: approx. 17 t

automatic baler Manufacturer: PAAL Type: KONTI 600 G/S/K with cross-binding Year of construction 2012 Operating hours: approx. 44,700 hours specifications: Press force: 1,546 kN System pressure: 315 bar Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 3 x 55 kW Pump capacity: 3 x 420 Ltr. Oil tank volume: 3,100 ltr. Throughput:approx. 780 m³/h Capacity at idle: approx. 1,220 m³/h Capacity at 35 kg/m³: approx. 26.5 t/h Output at 60 kg/m³: approx. 44.0 t/h Output at 100 kg/m³: approx. 69.0 t/h Control: Siemens S7 Setting: 5-fold vertical Additional 4-fold automatic horizontal tying Bale weight: approx. 800 - 1,250 kg depending on the material to be pressed and bale length Machine weight: up to approx. 42 t Includes a top pressure plate slot cover Printing plate was renew ...

Baler Paal Likon 80/60, built in 2004, very good condition Specifications: Manufacturer: Paal Type Likon 80/60 Year of construction 2004 Hours 13265 Press force 60 t Drive power 75 kW Total power 94 kW Filling opening 1600 x 920 mm Bale dimensions 800 x 1000 mm, length variable Setting 4-fold automatic Throughput 320 m³/h Throughput at 65 kg/cbm approx. 21 t/h Bale weight 660-1100 kg Transport dimensions approx. 9405 x 2200 x 2500 mm (LxWxH) Machine weight approx. 13 t Version with a 520 l pump, drive 75 kW, for an increase in power to approx. 320 cbm/h under operating conditions, including oil cooling. Materials: paper, cardboard, foil, wood fibers, etc. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. The offer is subject to change, subject to prior sale ...

Specifications Maximum pressure: 20 tons Press force: 2.6 kg/cm² Bale size: 1100 x 700 x 700 mm Bale weight: approx. 250 kg Power supply: 400V / 4kW Year of construction: 1995 Machine is fully functional, after technical supervision.  ... más información

Baler Europress 610 V5, year of construction 2012 / 2017 refurbished by the manufacturer, very good condition, with chain belt conveyor belt Europress Technical Data Press Manufacturer: Europress Type 610 V5 Year of construction 2012 / 2017 refurbished by the manufacturer Drive power 2 x 30 kW Press force 90 t Insertion shaft 1,450 x 1,100 mm Bale dimensions 1,100 x 730 x 1200 mm, length is variable Bale weight 400-900 kg 5-fold vertical setting, fully automatic Filling volume hydraulic oil tank 2100 L Transport dimensions excl. Press 8,500 x 2,650 x 2,850 mm Transport weight press approx. 21 t Detailed information on general overhaul on request. Technical data on the conveyor belt will follow. Currently, the press is still in use.

Horizontal hydraulic baling press with manual tying, brand: HSM, model: HL4010 Re, engine: 9 KW (12 hp), year: 2013, bale dimensions: 750x750 mm, bale weight: 280-300 Kg. Ready to get started? Contact us directly! Send us a WhatsApp message to (+34) 647 590 257 or an email to infogester.es for personalized advice.

Technical data baler:Manufacturer Presto GmbH & Co. KGTyp CC 36 MYear of construction 2010Hours of operation 3,641 hPress power main press 36 tSpecific press capacity 467 N/cm²Feed channel 1.080 x 1100 mm (l x w)Cycle time 34 sec.Capacity per cycle time 0,85 m³Theoretic throughput rate 90 m³/hThroughput rate under operating conditions with a material bulk density of 35 kg/m³ approx. 51 m³/hourBale size 1100 x 750 mm (w x h), length variableDriving motor 15 kWTying 4-fold vertical, semi-automatic, with polyester synthetic yarnThroughput rate at abulk weight of 35 kg/cbm 1,8 to/hbulk weight of 60 kg/cbm 2,5 to/hbulk weight of 100 kg/cbm 3,1 to/hTransport dimensions only baler 4.200 x 1.640 x 2.200 mmMachine weight baler approx. 4 toComments:The press was checked for function in our workshop, then stored and is therefore available at short notice. The machine documentation (operating  ...

Technical data baler:Manufacturer unoTech GmbH, Niederlangen, GermanyTyp 120 V5Year of construction 2009Press force main press 100 tonsSpecific press force 145 N/m²Max. cutting force 120 tonsPress force free stamper 25 tonsFeed channel 2,000 x 1,020 mm (l x w)Capacity per cycle time 1,5 m³Theoretic throughput rate 650 m³/hourBale size 1,100 x 750 mm (w x h)Driving motor 2 x 75 kWConnected load 160 kWRated current 280 ATying system 5-fold vertical, fully automaticThroughput rate at abulk weight of 20 to 30 kg/cbm up to 15 tons/hourbulk weight of 35 to 50 kg/cbm up to 23 tons/hourbulk weight of 60 kg/cbm up to 27 tons/hourbulk weight of 100 kg/cbm up to 44 tons/hourBale weight 600 up to 900 kg, depends on materialSPS controller (manuf., type) Siemens S7 300Operating panel (manuf., type) Siemens SIMATICTransport dimensions only baler 13.630 x 2.350 x 3.130 mm (l x w x h)Machine weigh ...

Briquette diameter: mm 180, Briquette diameter large mm 195, Force main cylinder kN 8,500, Briquette density steel, cast iron Kg/dm 5,5, Briquette density aluminium Kg/dm3 2,4, Briquette density brass, copper Kg/dm3 7.0, Capacity steel/cast iron t/h 7.5, Capacity aluminium t/h 3.5, Capacity brass/copper t/h 8.0, Drive power standard kW 180, Footprint m x m 6.5 x 8.5, Machine weight t 45, Year: 1999, Immediately available, Briquette diameter: mm 180, Year: 1999

Specifications Maximum pressure: 30 tons Press force: 3.13 kg/cm² Bale size: 1200x800x1200 mm Bale weight: approx. 300-350 kg Power supply: 400V / 5.5 kW Year of construction: 1999 Productivity: approx. 3 bales/hr If you have any questions, please call us: +48 696 072 985  ... más información

Vertical baler HSM VL 500.2, built in 2005 Specifications: Manufacturer: HSM Type: VL 500.2 Year of construction: 2005 Press force: 54 t Drive power: 7.5 kW Pressing time: approx. 43 s Filling opening: 1150 x 560 mm Bale size: 1200 x 800 x max. 1200 mm Bale weight: 420-450 kg Dimensions: 1900 x 1600 x 2200 mm (WxDxH) Weight: 2300 kg Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. The offers are subject to change, subject to prior sale and can be revoked at any time. Visits are possible by arrangement. The sale takes place from the location, without guarantee and guarantee. Our payment term is 100% prepayment.

Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw  ... más información

Hopper opening 400x500mm Control panel Connection 1x230V / 50Hz 10 Amps. 1 phase (or two phases if no neutral) or 1×220-240V / 60Hz 10 Amps. 1 phase or 115V / 60Hz Capacity with fish boxes made of 25 kg/m3: 15-20 kg/h Capacity measured in fish boxes with lids (650 grams per piece: 23-30 boxes/h Dry boxes (for wet boxes a 3 phase machine is better) Non-corrosive Mobile on wheels Density 175-225 kg/m³ 1,5kW 1-phase 230/110 V 50-60 Hz LxHxW 1950x1600x630 mm, Possible additions : exit tray, tub for exit tray, Stainless Steel version, See the chart below for other sizes, installed power : 1.5

A complete baling press system is for sale, consisting of a chain belt conveyor, the baling press with wire stations and bale chute.Technical data baler:Manufacturer BOAType Impress D130.110.B.5-(5R).1.6Year of construction 2009Press power main press 127 tonsSpecific press capacity 10,7 kg/cm²Working pressure 280 barFeed channel 1.620 x 972 mm (l x w)Press volume / cycle 4,1 cbmVolume throughput without load up to 865 cbm/hourCycle time under operating conditions 22 sec.Press stroke 2.900 mmBale size 1.100 x 1.100 mm (w x h) length adjustableDriving power 2 x 55 kWConnected load 132 kWTying system 5-fold vertical, 5-fold horizontal, fully automatedThroughput rate at abulk weight of 30 kg/cbm up to 17 to/hbulk weight of 50 kg/cbm up to 29 to/hbulk weight of 100 kg/cbm up to 37 to/hbulk weight of 150 kg/cbm up to 51 to/hBale weight up to 1.200 kgVolume hydraulic oil tank 1,850 LSPS contro ...

Technical data baler:Manufacturer according to type plate BRAMIDAN (original manufacturer Kampwert Umwelttechnik GmbH & Co. KG) Type HC 50 (formerly HPK 50 BK)Year of manufacture 2007Operating hours 11,970 hours, as of MarchPressing force 50 tonnesSpecific pressing force 650 kN/m²Feed chute dimensions 1250 x 1050 mm (L x W)Filling volume 0.96 cm³Theoretical cycle time 32 secondsTheoretical throughput capacity 108 m³/hourBale dimensions 1100 x 700 mm (w x h) length variableDrive power 15 kWPower consumption, total in 50 ATying 4-fold vertical, fully automaticThroughput rates with abulk density of 30 kg/cbm approx. 3.1 t/hourBulk weight of 60 kg/cbm approx. 4.5 tonnes/hourBulk weight of 100 kg/cbm approx. 7.2 tonnes/hourBale weights with a bale length of approx. 1.2 m up to 500 kg, depending on materialHydraulic oil tank capacity 400 litresPLC control Siemens S7-200 Effective transport  ...

Specifications Maximum pressure: 4.6 tons Press force: 1.31 kg/cm² Bale size: 500x700x700 mm Power supply: 400 V/ 1.1 kW Year of construction: 1993  ... más información

Baler Presto CC 20 M, built in 2019, baling force 20 t, with restraint device Specifications: Manufacturer: Presto Type: CC 20 M Year of construction: 2016 Press force: 20 t Cycle time: 24 s Drive power: 7.5 kW Filling opening: 1030 x 750 mm Filling volume: 0.53 m³ Binding: 4-ply, tape, manual Throughput at bulk density of 35 kg/m³ - 1.6 t 60 kg/m³ - 2.3 t 100 kg/m³ - 2.8 t Bale dimensions: 700 x 750 mm Bale weight: up to 300 kg Dimensions: 3300 x 1235 x 1860 mm (LxWxH) Machine weight: approx. 2500 kg Materials: paper, cardboard, foil Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. The offer is subject to change, subject to prior sale and can be revoked at any time. Visits are possible by arrangement. The sale against advance payment takes place ex works, w ...