outras máquinas de eliminação e reciclagem de resíduos usadas para venda

QUICK WASHER for RIGID and SOFT PLASTICS, made in AISI304 stainless steel, low water consumption, can be used with hot water or mild detergents, for reground LDPE LLDPE HDPE film, rigid PE PP PVC PET PA ABS PS PC, 7,5 kw motor 400V 50/60Hz, inner auger 400 mm diam., length 3.000 mm., material and water are loaded from the bottom, material discharging is done through a draining auger from top, bearings are positioned outside the wet chamber, seals on the lower bearing to exclude any contact with water, auger speed (and throughput rate) can be adjustable to change throughput rate 500 to 1.000 kg/h, by adding an inverter, Low water consumption (depending on contamination), The water can be mechanically filtered with a [water screening system](https://www.germanplast.eu/listings/5003567-germanplast-vibrat ing-screen-round-type) (available separately), This machine is to be electrically conne ...

Hazemag feed hopper with take-off conveyor Brand: Hazemag Dim. Bunker : 6800x1900/1000x1200 mm Trigger strap: belt width 1200mm, length 8M. Drive: Slip-on gearbox 1.5 kW  ... mais informação

used blower, Reitz MXE 160-003130-00 22kW as good as new Sale only to professionals, under exclusion of any warranty, prior sale, errors excepted.  ... mais informação

used blower, Herbold MFT 55/500 11kW Sale only to professionals, under exclusion of any warranty, prior sale, errors excepted.  ... mais informação

used blower, Herbold MFT 8/280 Sale only to professionals, under exclusion of any warranty, prior sale, errors excepted.  ... mais informação

Technical data Feed hopper with hydraulic moving floor and bag opener:Manufacturer BRT HARTNER GmbHType HP5-3035Year of construction 2015Hopper volume 30 m³ Drive line 17.5 kWDimensions in current state 13,200 x 3,050 x 4,350 mm (l x w x h)Condition of the machine:The feed hopper with bag opener was in use at a large recycling company, where waste in bags was tipped into the hopper with wheel loaders and the bags were opened via the bag opener and the waste was conveyed in doses for further processing. The system worked perfectly until it was dismantled and was replaced by a larger system with a higher throughput capacity. The machine is in good working condition. On request, various spare parts can be purchased for a separate, additional fee. The buyer would have to dismantle the elevation for removal, as the machine is otherwise too high.Comments:The documentation (Manual, CE-declarat ...

This ECS is used to separate the non-ferrous metal fraction from other scraps in plastic recycling lines.., It can handle very small parts but even larger ones, up to 400 mm, depending on the model., Metals which will be separated are : copper - alluminium - brass - bronze, Constructed in a workmanlike manner, durable and efficient machines made in Italy, these devices offer excellent performances in any plastic processing line., To get a customized offer, please send us :, - material processed and size, - contamination % and type, - max contaminants size, - throughput rate of the line

Dry cleaner/ friction cleaner with 110 kW drive power. Throughput approx. 1 -2.5 t/h depending on type of plastic and material thickness  ... mais informação

Hopper opening 400x500mm Control panel With thermal motor protection only available for: 3x230V / 50Hz or 3x400V / 50Hz 3x240V / 60Hz or 3x480V / 60Hz. Capacity with fish boxes made of 25 kg/m3: 15-20 kg/h Capacity measured in fish boxes with lids (650 grams per piece: 23-30 boxes/h Wet boxes Non-corrosive Mobile on wheels Density 250 – 350 kg/m³ 2,2kW 3-phase 400 V/ 50Hz 480 V/-60 LxHxW 1950x1600x630 mm, Possible additions: exit tray, tub for exit tray, Stainless Steel version, See chart below for more sizes, installed power : 2.2

Hopper opening 400x780mm Control panel Connection: 1x230V / 50Hz 10 Amps. 1 phase (or two phases if no neutral) or 1×220-240V / 60Hz 10 Amps. 1 phase or 115V / 60Hz 1 phase Capacity with fish boxes made of 25 kg/m3: 15-20 kg/h Capacity measured in fish boxes with lids (650 grams per piece: 23-30 boxes/h Dry boxes (for wet boxes a 3 phase machine is better) Non-corrosive Mobile on wheels Density 175-225 kg/m³ 1,5kW 1-phase 230/110 V 50-60Hz LxHxW 2220x1600x630 mm, possible additions: exit tray, tub for exit tray, Stainless Steel version, See the chart below for more sizes, installed power : 1.5

Hopper opening 560x1000mm Control panel with thermal motor protection only Available for: 3x230V / 50Hz or 3x400V / 50Hz 3x240V / 60Hz or 3x480V / 60Hz Capacity with fish boxes made of 25 kg/m3: 35-45 kg/h Capacity measured in fish boxes with lids (650 grams per piece: 50-60 boxes/h Wet boxes Non-corrosive Mobile on wheels Density 250-350 kg/m³ 4,0 kW 3-phase 400 V/50 HZ480 V/60 HZ Inlet opening 400×780 mm LxHxW 2900x1600x630 mm, Possible additions: removable bottom, removable bottom drawer, Stainless Steel version, See the chart below for more sizes, installed power : 4

Hopper opening 560x1400mm Control panel with thermal motor protection only Available for 3x230V / 50Hz or 3x400V / 50Hz 3x240V / 60Hz or 3x480V / 60Hz Capacity with fish boxes made of 25 kg/m3: 110-130 kg/h Capacity measured in fish boxes with lids (650 grams per piece: 170-200 boxes/h Wet boxes Non-corrosive Mobile on wheels Density 250-350 kg/m³ 15 kW 3-phase 400 V/50 HZ480 V/60 HZ LxHxW 4200x1600x870 mm, Possible additions: removable bottom, removable nottom drawer, Steinless Steel version, See the chart below for more sizes, installed power : 15

With combined pre-crushing and compaction of EPS material. Hopper opening: 300x490mm (11.8 x 19”). Control panel (1-phase) Connection: 1x230V / 50Hz 10 Amps. 1 phase (or two phases if no neutral) or 1×220-240V / 60Hz 10 Amps. 1 phase or 115V / 60Hz 1 phase. Capacity. Measured with fish boxes made of 25 kg/m3 density EPS 10-15 kg/h Wet boxes (it does work with wet boxes but less efficiently than a 3-phase model) Non-corrosive Mobile on wheels Density 140-225 kg/m³ 1,5kW 1-phase 230/110 V 50-60Hz Inlet opening 300×490 mm LxHxW 1850x1400x660 mm, Possible addition: exit tray, tub for exit tray, Stainless Steel version, See the chart below for other sizes, installed power : 1.5

Dosing Conveyor Belt Ammann Brand: Ammann A.A length = 1200 mm. Belt width: 650 mm. Drive: 2.2 kW slip-on gearbox Speed approx. 0.8 m/sec In stock: 6 pieces.  ... mais informação

Galvanized handrails for walkways Brand: Kleemann Dim.: 5000 mm length - 1240 mm height Made of square tubular profile 40x40 mm In stock: 45 pieces.  ... mais informação

Used and refurbished turbine mill from Tecnoecology for the digestion of old cables, especially fine strands or computer cables. Balling takes place at about 3,000 rpm. The tools are rotatable and have 4 usable edges. The turbine mill can be operated stand-alone or integrated into an existing system without a pellet mill. The machine has a 20 kW drive and can process up to approx. 300 kg of material per hour.

The JMC 407 is the top seller among our alligator claws. It is cost-effective, has sufficient knife length and enough power for most metal recycling tasks. It is suitable for cutting many materials, such as profiles, piping, motors, gearbox housings. The scissors are also often used for cleaning scrap metals or cutting vehicle radiators. The machine is equipped with a control system without electronics and a manually adjustable hold-down device, which also acts as a protective cover. By means of a foot pedal, the scissors can be used in single or continuous operation. The opening width can be adjusted by means of simple clamping screws. The scissors are from our demonstration pool and can be viewed or tested.

Made in sturdy painted carbon steel or AISI 304 stainless steel, drained or covered,.. Customized to your project, just send us your sketch with length, inner and outer diameter, drive, configuration or share your project with us and we will offer you the best solution. ... mais informação

Feeding chute Svedala Brand: Svedala Length 2200 mm - Width 1200 mm with two vibration motors of 1.3 kW each  ... mais informação

- Complete system - incl. conveyor belt width 800 mm - Incl. discharge hood with separating parting - incl. SOFTWARE UPDATE FROM PELLENC - incl. COMPLETE OVERHAUL IN OUR SPECIALIST WORKSHOP IN D-59329 WADERSLOH - incl. COMPLETE DOCUMENTATION - YEAR OF CONSTRUCTION 2015  ... mais informação