New Generation Polymer Formwork Panels, 18mm New generation formwork panels for maximum efficiency. The polymer panels can be nailed or cut like conventional formwork panels. No deformation, rot or rust possible. The panels are more durable than any other wooden formwork panel, even under the toughest working conditions. - Formwork plate made of polymer plastic - Weight of the plate 32kg - Dimensions 1.25 x 2.50m - Recyclable - € 20,55 per m2 New Generation Polymer Plywood, 18mm New generation formwork panels for maximum efficiency. The polymer panels can be nailed or cut like traditional formwork panels. No deformation, rot or rust possible. The panels are more durable than any other wooden formwork panel, even under the toughest working conditions. - Polymer Plywood - Sheet weight 32kg - Dimension 1,25 x 2,50m - Recyclable - € 20,55 per sqm

NOE Alu L A lightweight system that can be used to work independently of the crane. The NOEalu L convinces as a real hand formwork, due to its low weight, high flexibility and durability. The low weight of 21 kg/m² Ensures long-term productive Work, even without a crane. The sturdy construction will meet the to cope with the stresses of everyday construction site life. Flexible thanks to a wide, Vertical or horizontal table assortment. The Alulock connects the various components of the system as reliable as it is escaped. The individual panels allow a concrete pressure of up to up to 60 kN /m². NOE Alu L A lightweight system, for work without crane. The NOEalu L convinces as an Hand formwork, due to low weight, high flexibility and durability at the same time. The low weight of 21 kg/m² ensures a permanently productive work, even without a crane ...

Carrier Doka H20 Top P The carriers are manufactured by Doka 8.415m - available lengths: 2.45m 2.65m 2.90m 3.90m € 3.85 per meter Formwork carriers as a well-used com-po nen ten for vie-le-relungs-sys-me. Formwork carriers are available as ba sis vie'ler Scha-lungs-sys-te-me and uni-ver-sell. The carefully used carriers are suitable for the years of the construction. The location is our warehouse in 5202 Neumarkt For further information or a visit I am at your disposal at any time. You can reach us at Tel.Nr: +43 664 1296830 or by e-mail: office@berger-international.at Berger Construction Equipment Ltd.

Bar attachment 60 Used - ready for immediate use! Galvanized beam clamps for support in beams and edge and ceiling formwork Length: 60 cm 4.4 kg Price: € 16,00 301 pieces in stock  ... más información

Balkenzwinge 20 – galvanized Used - ready for immediate use! Galvanized beam clamps for support in beams and edge and ceiling formwork Length: 30 cm Height: 35 cm 6.9 kg Price: € 32,00 356 pieces in stock forming support 20 – galvanized Used - ready for immediate use! Galvanized beam clamps for supporting beams and edge and slab stop ends Length: 30cm Heigth: 35cm 6.9 kg Price € 32,00 356 pieces on stock

Support bracket Universal F 4,50m For concreting heights up to 4.00m The "Abstützbock Universal" is a simple and uncomplicated way to support formwork with attachments up to a maximum height of approx. 4.0 m. Features: ▪ Suitable for beam and frame formwork. ▪ Tensile forces are reliably transmitted by diagonal armatures. ▪ Adaptation to the different fresh concrete pressures Required is simple and economical – simply increase or decrease the distance between the load-bearing structure, frame. 17 pieces available EUR 721,00 per pcs.

Universal formwork Paschal Raster Universal formwork for foundations, walls, columns, beams, shafts, curves (polygons), landscaping construction, prefabricated elements. Versatile and flexible for use as manual and large-area formwork. Thanks to the modular principle, systemic formwork is very possible, even with complicated floor plans. The flat steel frames guarantee the robustness and durability of the formwork. Compatible with all PASCHAL systems. Connecting bolts as a universal fastener for all elements and accessories.

Painted ceiling supports 3.60m Steel construction supports with a red dip bath paint. Decoupling system - this enables a quick disarming of the support with little effort Foot reinforcement - by mounting a stronger pipe near the footplate Due to holes every 100 mm in the inner tube, the extension length varies between 50 and 500 cm Compatible with most of the accessories of other formwork Technical data: Inner and outer tube made of steel S235JR according to UNI EN 10219-1 / 2 concealed threads, step 8 mm, for adjusting the length Threaded pins directly on the outer tube, or welded, manufactured by rolling, i.e. without rejecting the material Lower plate available in flat or curved version Upper plate available in three versions (flat plate, with fixed cross or "U"-shaped) Highly resistant safety hook for fastening between inner and outer tube Hand-squeezing for safe con ...

Doka Tripod The tripods are in very good condition and can be used immediately. 780 pcs available  ... más información

Safety railing clamp for screwing Safety on every structure These tried-and-tested systems give your site crew optimum protection and make a significant contribution to a smooth workflow. When the crew are properly protected, they work safely, which also means more rapidly and thus more efficiently – for your success. Doka handrail posts provide comprehensive safety • against fall hazards • on the structure and the formwork • thanks to their high quality (hot-dip galvanised) • conform to EN 13374 Class A Convenient and easy to mount Multi-functional as they can be used in many different situations ? maximum safety with easy assembly ? no squared timber waste

Hünnebeck Manto 330 â?¢ Strong connection can be implemented by directional angle: 40 m ² of shell surface in a crane excavation without additional stiffening â?¢ highest bending strength due to the 14 cm high steel frame; Permitted concrete print 80 kN/m ² â?¢ rational shelling of large areas without compensation and with few anchoring points using MANTO XXL panels â?¢ Light and fast â or shelling of shafts with the MANTO chess corner â?¢ consistently good concrete image due to fire galvanizing of the frame and high-quality shakheads â?¢ Also suitable for shells finely skinned walls. 132m ²-EUR 19,969,60 Stocked: Table/Panel 90 x 330 â 20 Stk/pcs. Table/Panel 75 x 330 â 20 Stk/pcs. Inner corner/ash Inner Corner 35/330 â 6 Stk/pcs. Exterior ecke/Ou ...

MevaDec Lighter and more ergonomic: The new generation of the MevaDec impresses with its lower weight and high cleaning friendliness of all components as well as optimized handling properties – based on all the proven system advantages of the MevaDec. • Size and weight o Weight-optimized system for ergonomic and therefore efficient working o Largest element 160/80 cm only 16 kg/m2 - almost all requirements can be covered with only one element dimension • Safety due to support grid specified by the system • One system - three ceiling formwork methods o Fall head-carrier element method (RTD) o Main and secondary carrier method (HN) o Element Method (E) • Closed profile made of aluminium o Ergonomic handle profile o High-quality burn-in powder coating for high cleaning friendliness and reduced concrete adhesion • Sophisticated MEVA product design o High-quality ...

The high-load timber-beam formwork with a system grid The pre-assembled standard elements of Doka timber-beam formwork FF20 combine the advantages of timber-beam formwork with the grid-related advantages of a framed formwork system. Their very high load-bearing capacity offers a new degree of freedom when it comes to fulfilling architectural specifications in a cost-effective way. FF20 is suitable for fair-faced concrete categories SB1 to SB4, as defined in the DBV Code of Practice. High pouring rates made possible by extra-strong components Up to a pour-height of 3.60 m, only two 20.0 form-ties are needed, thanks to the 80 percent higher load capacity of the I tec 20 composite formwork beam compared to conventional H20 timber formwork beams the stiff FF20 tec walings WU14, with their welded-on plates Maximised utilisation of equipment and ease of handling Lowers commi ...

-reliably high load capacity across the entire beam length thanks to homogeneous web material -secured component load capacity, as all of the straps are machine stress graded and load-tested -consistent product characteristics owing to high dimensional stability -multiple savings compared to squared timber due to improved load capacity combined with lower weight -Certification EN 13377 -Produced in Austria from Doka Industrie The length of the H20 smart beam varies from 2,45m until 5,90m. Costs: 5,00 EUR/rm For more information or an appointment, you can contact me at any time. Phone: + 43 664 1296830 or Email:office@berger-international.at

The frame and the formwork is in a used good condition and can be used immediately. 26x Framax 1.35x2.70m 10x Framax 0.90x2.70m 6x Framax 0.60x2.70m 4x Framax 0.45x2.70m 4x Framax 0.30x2.70m 4x Framax 0.90x2.70m Uni 4x Framax inner corner 2.70m 2x Framax outer corner 2,70, 120x Framax RU Clamp 10x Framax Uni Spanner 10x Framax Universal Connector 10-16cm 12x Framax clamping clamp 4x Framax clamping rail 0.90m 2x Framax clamping rail 1.50m 1x Framax conversion bracket Other quantities or elements are available on request. Frame formwork Framax The high-performance steel frame formwork for large-area shelling with the crane Framax is the frame formwork system that achieves a consistent 15 cm grid with only a few elements, whether used standing or lying. All fasteners, all accessories blend seamlessly into the grid for fast formwork times and high cost-effectiveness ...

Just one blow of the hammer on the RU clamp is all it takes to pull the panels together and achieve a flush, correctly aligned panel joint that is resistant to tensile forces. The panels can be continuously height mismatched, i.e. without any pre-defined grid. This means that the formwork can easily be accommodated to e.g. steps, slopes and uneven ground, with no extra work.

Gabelkopf H20, verzinkt, Neu Ausführung mit 4 Winkelprofilen und Rohransatz mit Langloch, passend in alle DIN oder Euro Norm Gewicht 3,20 kg  ... más información

Doka 3-ply sheets provide the basis for many Doka formwork systems and have a wide range of uses. Doka has the right solution for all requirement, covering anything from standard applications to rentable panels. Multiple use and prevention of positive imprints through closed surface on both sides coated with high-quality melamine resin. Lower costs for finishing work based on high dimensional and angle accuracy. Type: 3-ply formwork sheet made of spruce, crosswise glue-bonded, with edge strip Surface: urea-melamine resin adhesive high degree of format accuracy

Doka 3-ply sheets provide the basis for many Doka formwork systems and have a wide range of uses. Doka has the right solution for all requirement, covering anything from standard applications to rentable panels. Multiple use and prevention of positive imprints through closed surface on both sides coated with high-quality melamine resin. Lower costs for finishing work based on high dimensional and angle accuracy. Type: 3-ply formwork sheet made of spruce, crosswise glue-bonded, with edge strip Surface: urea-melamine resin adhesive high degree of format accuracy

With its 15 cm clamping range, the Framax multi-function clamp matches the panel size-grid exactly. This means that only one closure is needed per wall plane.  ... más información