Fabricante:
(Categoría: 503)
Pre-shredder / shredder / chopper Fabr. Piranha for wood and plastic Motor 37 Kw Shaft length 600 mm with 3 x 5 Schneider knife with sieve 35 mm with control ... más información
JMC 900 alligator shears (new machine) The JMC 900 has a hydraulic hold-down. The scissor head is operated with a foot pedal for individual cuts or continuous cutting. The scissor head is protected with a safety basket. Out of stock Delivery time: On request Manufacturer: Mc Intyre Knife length: 920 mm Measuring opening: 473 mm Cutting capacity: 233 tons Round iron ST 37: 88 mm diameter Number of strokes at 1/4 aperture: 26 / min Number of strokes at full opening: 9 / min Dimensions ( L x W x H ): 3200 x 1030 x 1800 mm Weight: 4400 kg Drive: 18.5 kw / 400 V + 1.5 kw electric motor cooler Operation: Foot pedal
Alligator scissors Lindemann Alibo The Lindemann Alibo has a mechanical hold-down. The scissor head is protected with a safety basket. Machine On hand Knife length : 760 mm Weight : 4200 kg Mouth width at the tip : 200 mm Cutting capacity: 0.45 kN/ mm² : Ø 70 mm Number of strokes : 20 – 40 cuts/min Dimensions: 4.20 x 1.50 x 1.80 meters Drive: 15 kw Hold-down: Mechanical
The JMC 150 has a mechanically adjustable hold-down. The scissor head is operated with a foot pedal for individual cuts or continuous cutting. The scissor head is protected with a safety basket. The JMC 150 is a tabletop unit for easy handling. Manufacturer: Mc Intyre Knife length: 150 mm Measuring opening: 105 mm Cutting capacity: 25 tons Round iron ST 37: 25 mm diameter Number of strokes at 1/4 aperture: 20 / min Number of strokes at 1/2 opening: 12 / min Number of strokes at full opening: 9 / min Dimensions ( L x W x H ): 660 x 520 x 620 mm Weight: 150 kg Drive: 1.5 kw / 230 Volt Operation: Foot pedal
Used JMC 407 Kat Alligator Scissors Alligator scissors JMC 407Cat The catalyst version JMC 407 has an additional "V-holder" in the cutting area for adjustment when cutting or opening the catalysts. In stock at the end of March 2021 Knife length: 407 mm Measuring opening: 250 mm Cutting capacity: 90 tons Round iron ST 37: 57 mm diameter Number of strokes at 1/4 opening: 63 / min Number of strokes at full opening: 11 / min Dimensions (L x W x H): 1550 x 880 x 1120 mm Weight: 880 kg Drive: 7.5 kw / 380 V Operation: Foot pedal
Manufacturer: Deltax Holder: Hydraulic holder Dimensions (L x W x H): 2010 x 902 x 1500 mm Knife length: 610 mm Number of strokes at 1/4 opening: 40 cuts at quarter opening Number of strokes at full opening: 12 cuts at full opening Measuring opening: 330 mm Cutting force: 206 tons Drive: 11 kw/32 CEE plug Weight: approx. 2250 kg Deltax_DTX600S with hydraulic holder (New machine) The DTX 600S has 20% more cutting power than the standard Deltax DTX600. This was achieved by installing a larger cylinder and using a smaller second pump. A larger first pump is used to maintain the same cutting speed. All other modifications are used to amplify the machine to handle the additional power. The weight gain due to the reinforcement modifications and the larger pestle is about 250 kg. Alternatively: Deltax DTX600 Difference Cutting force: 172 tons | Weight: 2000Kg | All othe ...
Manufacturer: Mc INTYRE Blade length: 150 mm Blade opening: 105 mm Cutting capacity: 25 tons Rods ST 37: 25 mm diameter Number of strokes at ¼ opening: 20 / min Number of strokes at ½ opening: 12 / min Number of strokes at full aperture: 9 / min Dimensions (L x W x H): 660 x 520 x 620 mm Weight: 150 kg Drive: 1.5 kw / 230 Volt Control: foot pedal
Small but very robust and powerful shredder for a wide range of tasks such as old cables, plastics, wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). Rotor shaft with connections for connecting a cooling unit (e.g. when used for old NYM cables. The machine is and little used from our demo machine inventory. The machine is offered with a one-year used machine warranty.
Small shredder for various tasks such as old cables, plastics wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). Rotor shaft with connectors for connecting a cooling device (e.g. when used for NYM old cables. The machine is 1 year old and little used from our demo machine inventory. The machine is offered with a one-year used machine warranty.
Small shredder for a wide range of tasks such as old cables, plastics wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). The machine was overhauled by the manufacturer ISVE in September 2020 and supplemented with an electronics for networking into a cable recycling line. A rotor cover for the optimized processing of old cables has also been added. Currently, the shredder has a 16 mm hole sieve but other hole diameters can also be added. With the 16 mm hole sieve, the shredder reaches about 250 kg/hour when processing mixing cables.
Large Four Shaft Shredder with Two Cutting Shafts and Two Feed Shafts. Until now, the shredder has been used as a pre-shredder for the recycling of old cables. Due to the hydraulic tamper, the shredder can also be used for bulky materials. Changing the screens is hydraulically assisted and therefore easy to do. On request, the shredder can also be supplied with the articulated conveyor belt shown here. The conveyor belt is equipped with a magnet in the upper pulley for iron separation.
The MR 40-80 is a powerful single-shaft shredder for many tasks, such as the pre-shredding of cables, the crushing of electronic waste, used plastics, wood, etc. Unlike other single-shaft machines, IRS's shredder has two instead of one series of stator knives for better product quality and higher hourly output. The optimized arrangement of the rotor blades also reduces energy consumption. The horizontally acting hydraulic pusher has replaceable wear strips and regulates the contact pressure on the rotor. In addition, there are interchangeable screens for special tasks from 10 mm hole diameter. On request, the shredder can be optimized for cooling the rotor shaft, with wear protection armor, hydraulic clutch, remote services and other options for the respective application. Specifications: Number of knives: 35 + 2 (rotor + stator) Rotor speed: 85 rpm Rotor Ø, length: 400 mm, 80 ...
Used single-shaft shredder for wood, plastics, old cables, etc. Of course, the machine has received new knives and has been checked by us. Accordingly, we give 3 months of used machine warranty. The shredder has the amplified 30 kW drive (normally 15 kW) and is therefore enormously powerful. The rotor stops in the event of overload or blockage and reverses automatically. The hydraulics of the machine are dry, there are no leaks. Currently, a screen with a hole diameter of 14 mm is used, so that it is perfect for old cables. Of course, other screens in the range of 10 mm to 60 mm can also be used. The shredder is immediately available and can be viewed and tested. Further technical data: Rotor length: 630 mm Rotor diameter: 250 mm Feed travel: 600 mm Loading opening: 1,100 x 1,100 mm Drive rotor: 30 kW Drive hydraulics: 1.5 kW Rotor speed approx.: 90 rpm Weight ...
Hump shredder PHSS 40/110 Specifications: Manufacturer: Höcker Polytechnik Type: PHSS 40/110 Year of construction: 2011 Drive power: 22 kW Working width: 1100 mm Rotor diameter: 400 mm Cutting principle: high-speed shredder shaft with counter comb Material: Punching Waste, Cardboard Punching Mesh, Corrugated Cardboard
COMPLETE REFUSE-DERIVED FUEL PLANT WITH HIGH CAPACITY Year of construction 2009 13,500 operating hours - 1 x pre-shredder TYPE VECOPLAN - 1 x Magnet - 1 x air classifier TYPE WESTERIA - 3 x secondary shredder type VECOPLAN - approx. 150 meters of conveyor belts - Electrical control - Spare parts worth approx. € 70 000 Installed capacity approx. 1200 kW Product size 25 to 80 mm according to customer's requirements. We can dismantle the system and load it onto trucks.
Scrap shear dentition attachment for an excavator used MBI ZHEJIANG MANTOVANI MANTOVANIBENNE Type MS22-MC Year: 2020 suitable for multipunch MS22R Overall dimensions: 1100 x 1100 x 500 mm Changes and errors in the technical data, information and prices as well as prior sale reserved ... más información
Scrap shear dentition attachment for an excavator unused MBI ZHEJIANG MANTOVANI MANTOVANIBENNE Type MS15-MC Year: 2020 Overall dimensions: 1100 x 1000 x 500 mm Changes and errors in the technical data, information and prices as well as prior sale reserved ... más información
Tank scissor dentition, scrap scissor bit attachment for an excavator used MBI ZHEJIANG MANTOVANI MANTOVANIBENNE for MS22 Overall dimensions: 1400 x 1300 x 500 mm Changes and errors in the technical data, information and prices as well as prior sale reserved ... más información
Wood shredders, plastic shredders, garbage shredders, two-shaft shredders, shredders, shredders used Manufacturer: I.S.V.E. Srl Type: 80-80 D Year of construction: 2003 Insertion approx. 1500 x 900 mm Insertion height approx. 1600 mm Drive 2x 9 kW 380 V Dimensions: approx. 2400 x 1800 x 2400 mm Changes and errors in the technical data, information and prices as well as prior sale reserved.
For sale is a processing plant for third-party take-back polystyrene - fully functional. Feeding table: 2000x2000x900 Belt conveyor: 1420x4000 Slope: 21° Transport speed: 4-16 m/min Design: (50Hz):8m/min Styrofoam mill: 2180x2496x1590 Filling opening: 1500x1000, weight 1500kg ... más información