tornos usadas para venda

turning diameter over bed: 3.150 mmturning diameter over slide rest: 2.650 mmturning length: 15.000 mmControl: CNC Siemens 840D workpiece weight: 160 tnumber of spindle speeds: 4 Bereiche – von 0,25 bis Pictures from location. Machine is now in warehouse in dismantled condition. See last picture.8 steadiesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Condition: very good mechanical part Technical details : Turning diameter 3200mm Table diameter 3200mm Turning height 2000mm Max workpiece weight 50 t Table speeds 0.66-62.1 rpm Vertical crossrail movement 1870 mm Main motor power 125 kW Machine dimensions 5100 x 9200 x 7200 mm Machine weight 90.4 t

turning diameter over bed: 720 mmturning diameter over slide rest: 500 mmturning length: 1000 mmspindle turning speed range: 7.1 - 1800 U/minfeeds - fine adjustment: 6 - 6,28 mm/Ufeeds crossrail-slide horizontal: 0,005 - 6,28 mm/Uspindle drive: 15 kWcentre height: 360 mmspindle bore: 82 mmtotal power requirement: 28 kWweight of the machine ca.: 3 tdimensions of the machine ca.: 2,8 x 1,4 x 1,8 m3-jaw chuck: 315 mmQick Toolholders: Multifix GR. 8 Digital Read Out: Acu-Rite Face plate: 600 mmmotorized top slide: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 1320 mmturning diameter over slide rest: 820 mmturning length: 4400 mmControl: faceplate: 1200 mmbed width: 800 mmspindle passage: 167 mmsteady: 480 control: IMS total power requirement: 76 kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 1450 mmturning diameter over slide rest: 1070 mmturning length: 7000 mmturning speeds: 2,24-450 U/minControl: faceplate: 1400 mmspindle passage: 160 mmsteady: 400 mmdrive capacity - workpiece: 63 kWTail stock:: elektr. diameter of quill: 200 mmbed width: 950 mmcontrol: Siemens total power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Specifications: Center height: 220 mm Center width: 1000 mm Spindle bore: 55 mm Bed width: 430 mm Speeds, 2 stages: 18 - 1800 1/min Tailstock mount: MK 4 Quill stroke: 190 mm Feed rate: 0.30 - 3.26 mm/rev Dimensions (WxDxH), approx.: 2650 x 1100 x 1550 mm Equipment: - Quick-change holder System Multifix - Bed stop - Coolant device -Mudguard - Turning chuck protection with restart protection

LZ lathe. Tip height 200 mm. Top width 1000 mm. 16 spindle speeds 40-2000 RPM. Coolant system. Quick change Toolpost. Geometric, machine has been revised. Digital display.  ... mais informação

Machine is fully functional and has its own cooling and a Heidenhain digital has a three-jaw chuck and a clamping width of 450mm is 3 meters long and 3 tons heavy you can clamp through the jaw chuck so longer workpieces are no problem it has a rotary heart and various cornel and jaws to exchange machine is in a very good condition and machine manuals are included

: Ravensburg A2,2 circulation diameter max.: 2.200 mmdiameter of quill: 90 mmweight of the machine ca.: 1,4 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... mais informação

turning length: 1000 mmturning diameter over bed: 430 mmturning diameter over slide rest: 235 mmspindle turning speed range: 11.2 - 2000 U/minspindle bore: 56,0 mmmorse taper: 4 MKquill stroke: 135 mmbed width: 333 mmspindle taper: DIN 55022 Gr. 6total power requirement: 7,75 kWweight of the machine ca.: 1950 kg.dimensions of the machine ca.: 2700 x 1200 x 1600 mm from a workshop for the disabled ()Furnishing:- robust master/feed spindle machine- FORKARDT 3-jaw chuck Ø 200 mm (DIN 55027 size 6)- HEIDENHAIN digital display- MULTIFIX steel holder, with insert- Movable tailstock- chuck key- chip rear wall- sliding bed stop- Protection for bed rails- live center- Coolant device, with drip trayThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Digital Workpiece weight 8 t Crossbar adjustment 800 mm Chisel travel 700 mm Swivel angle max. 45 +/- degrees Special equipment: wet turning device, Fine-tuning chisel device, incl. accessories Machine weight approx. 13.5 t Space requirement approx. 3.4 x 5.8 x 4.5 m  ... mais informação

turning diameter over bed:425 mmturning diameter over slide rest:215 mmturning length:1000 mmturning speed range:11,2 - 2240 U/minfeed range:0,02 - 1,6 mm/Uspindle bore:62 mmtotal power requirement:10 kWweight of the machine ca.:3 tdimensions of the machine ca.:2,8 x 1,2 x 1,3 mwith rapid feedcoolant attachment3-jaw chuckMULTIFIX toolholder system

Producent: KRAMATORSK Model: 1A670 Condition: Good, machine is complete, Year of manufacture: 1975 Technical details Swing over bed: 2000 mm Swing over carriage: 1600 mm Max. distance between centres: 10000 mm Width of bed: 2240 mm Centres height: 1060 mm Max. workpiece weight: 63 000 kg Spindle hole: 80 mm Spindle cone ( 1:7): 120 mm Tailstock taper (1:7): 120 mm Spindle speeds range( stepless): 1-125 rpm Main motor power: 100 kW Installed power: 112,5 kW

turning diameter over bed: 1000 mmturning diameter over slide rest: 710 mmturning length: 7000 mmmax. workpiece weight between centres: 10000 kgspindle turning speed range: 1,8-400 U/mintailstock quill taper metric: 80/1:10 tailstock - quill dia: 170 mmtailstock - travel of quill: 200 mmTailstock quill travel speed: 2150 mm/minmain drive motor: 37 kWlongitudinal feeds:: 0,125-48 mm/U face feeds: 0,4 der Längsvorschübe weight of the machine ca.: 17 tdimensions of the machine ca.: 11x1,9x2 mmachine was mechanically and electrically overhauled in the last years.- taper turning function- 3 lynettes- misc. center points for tailstock- set of change gearsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

- 6 spindles - Max. bar clearance: 63.0 mm - Rod guide and stand including many accessories (see photos)  ... mais informação

Schuette multi-spindle rotary machine SF 50/51-6 Rod turning machine run on schneidoel standart Schuetz control mechanical gearbox Hydraulics integrated into the machine with snail-spaenefoerer  ... mais informação

Typ/ type: TUD- 40 Hersteller/ make: WAFUM Year of make: 1975 Swing over bed/ slide: 400 /225 mm Drehlänge / turning length: 500 mm Working spindle hole in spindle: 56 mm Main spindle cone: Morse 6 Tailstock quill cone: Morse 5 Diameter of the tailstock quill/ diam. Sleeve: 90 mm Adjustment sleeve: 180 mm 21 working spindle speeds/ 21 speeds: 18..1800 rpm Longitudinal feeds / long. Feed: 0.08 .. 3.26 mm / rev Plan feeds /cross feeds: 0.04.. 1.63 mm / rev Thread pitches / threads: metr. Thread: 1..88 mm Inch thread: 1..88 gg./ 1" Module thread: 0.25..3.5 module Diametrical pitch thread: 112..8 pitch Rapid travel of support: 4.2 m / min Connected power: 7.35 kW Weight of the machine: approx. 2.8 t

Used Schutte Se 16 Multispindle automatic lathe model Se 16 six spindles, year 1975 maximum diameter with counter-pliers 18 mm, with the automatic loader it becomes 22 mm. electrical panel redone The machine is already set up for the loader, but it also has the tube and the stand ... mais informação

Conventional Vertical Lathe O-M TMS2-18/40 Made in 1975. Table size: 1800mm Max swing: 4000mm Max turning height: 1500mm Condition Under power.  ... mais informação

Maximum machining diameters: 4000 mm / 3500 mm (clamping plate) Clamping plate speed: max. 80 rpm Maximum workpiece height: 2000 mm Main drive power: 55 Kw Note grinding equipment Maximum workpiece weight: 40t Regular service and maintenance ... mais informação