máquinas de borracha usadas para venda

Qty 1 x Werner & Pfleiderer tangential (Banbury type) Lab internal mixer, Type: GK-1.5N Year: original 1982 Volume: 1,5 L Friction: fixed Gear-box ratio i:1: 13,51 / 15,00 Rotor Speed: variable Ram: pneumatic Discharging: drop door Drive: 22 kW, 440V DC variable speed. Automatic lubrication. In very good condition. Complete with electrical controls etc. Overall dimensions (approx) 2m x 1m x 1.8m high, weight: 1.8ton

available Berstotff Rollerhead - Extruder Cold Feed Extruder - 200mm x 218D 2 roll calendars 400mm x 1200mm see attached description!  ... mais informação

1 x Refurbished Pomini Farrel model P160 Banbury internal mixer, Original year of manufacture 1984, Rebuilt in 2017 (not used since), Mixing chamber volume 160L Net, Batch size at 75%FF and SG 1.0 - 120kg, 2 wing rotors, PYH hydraulic dust stops (new), hydraulic drop door discharge with linear actuator and spade latch, Pneumatic hopper, Unidrive gearbox type NF160, rating 640HP, Input speed 1500 rpm, output 39.6rpm. with 470kW, 500V DC variable speed motor. Mechanically complete but currently without electrical controls.

Polish roll mill 550 x 1500mm. Roll gap adjustment - motorized. Main motor power 90kW. Very good technical condition.  ... mais informação

1 x Meccaniche Moderne 1500mm x 560mm dia two roll mill, Type: DUPLOCOM, Year 1984 but refurbished in 2001 to CE regulations. Peripherally drilled rolls, motorised nip adjustment (2.2kW to each roll), with 37kW, 1450rpm motor fitted to each roll, Friction ratio 1:1.24, Back roll speed 16.1rpm, front roll speed 12.9rpm, 3ph, 380V, 50Hz.

1 x Werner & Pfleiderer 400mm dia dump extruder, Type: EAE400, Fabrik nr 221284, Werk nr 416295, Year: 1985, double hydraulic crammer feed, feed section 965mm wide, L/D ratio 8:1, with 235kW DC variable speed motor, Sheeting head to produce up to 1000mm wide sheet. Complete with controls and hydraulics etc.

Joos Upstroke Press Type HP-S180 Platen size 2800mm wide x 1500mm deep Operating pressure 180ton 550mm daylight 1800kN Year 1985  ... mais informação

chamber volume: - literuseable volume: 1,6 literfriction: - motor drive power: 22 kWCondition: used - overhauledSpecification: Laboratory internal mixer - second-hand- chamber volume: approx. 1.6 l- closing system: front door with pneumatic piston- plunger: pneumatic- rotor geometry: tangential type- Oil-free self-lubricating sealing rings- New rotary union for water cooling- New main gearbox- New AC motor: 22 kW- Control cabinet: NEW- Control panel with OP 7: NEW- Wiring: NEW- New frequency converter for variable speed- Paintwork: according to customer specifications- With safety devices according to current standard- overhauled, with warranty 12 months, with CE-marking, Operating and maintenance instructions in EnglishThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Choice of 2 x Francis Shaw K7 MK3 intermix, Total Volume: 320L, Useful volume 210L, Order number: 6061/1 and 6061/2, Year of manufacture: Oct 1986, NR2 Rotors, SSA type dust seals, Hydraulic drop door with linear actuator, Pneumatic hopper, Zamech full unidrive gearbox, Type: WD263-22.5, ratio 22.5:1. with 1000kW, 990rpm, 6000V motor. Rotor speed 44rpm. With modern starter panel, but without operator controls.

Francis Shaw KO Intermix Year: Jan 1987 Approx. mixing capacity 1.8 litres Mawdsley DC motor, shunt wound, serial no. 180T827, 30kW, 460 volts, 74 amps, 1800rpm, continuous rating Apex Denison Hydraulic Pump Holroyd Gearbox Barco Rotary Joints Fortress Interlock system Water steam inlet Water steam drain Mixing Chamber Rotors Plunger Drop Door Grease points With Hopper Thorn EMI electronic star drive; 415 volts, 3 wire, 50 cycles, 54kva, November 1987 Operator Panel consisting of rotor speed, main motor current process timer, mix temperature Complete with control panel

Francis Shaw KO Intermix Year: Jan 1987 Approx. mixing capacity 1.8 litres Mawdsley DC motor, shunt wound, serial no. 180T827, 30kW, 460 volts, 74 amps, 1800rpm, continuous rating Apex Denison Hydraulic Pump Holroyd Gearbox Barco Rotary Joints Fortress Interlock system Water steam inlet Water steam drain Mixing Chamber Rotors Plunger Drop Door Grease points With Hopper Thorn EMI electronic star drive; 415 volts, 3 wire, 50 cycles, 54kva, November 1987 Operator Panel consisting of rotor speed, main motor current process timer, mix temperature Complete with control panel

Screw with vacuum zone, output approx. 255 - 400 kg/h, straight head  ... mais informação

available Troester Triplex Extruder Top machine QSM 90x 16D Middle machine 200W x 6D Below machine QSM 150 x 16D Head MW500 Description attached!  ... mais informação

Bartell FSW-409 7/8in bead winding machine suitable for PCR tyres 12in to 20in consisting of: - 12 station bead wire let of unit. - Prodicon zig zag cutter Type Z/Z year 1988 (takes sheet compound max 750mm wide and cuts to suitable size for feeding extruder. - 60mm dia coldfeed extruder, L/D ratio 13:1, with 18.4kw DC variable speed motor and 3 x TCU's - Festoon section - Former unit with various Bartell formers available/included. - Siemens S5 plc controls.

Roller die line consisting of:- 1 x Troester 200mm pin barrel extruder Type QSM200K-16D power roller feed, 10 rows of 8 pins, L/D ratio 16:1 Serial no. 1816/88, year 1988, With temperature regulation unit, 282kW ASEA DC variable speed motor mounted on rails (moves away from calender to clean out etc) Hydraulic sheeting head linked directly to:- 1 x Adamson 24in dia x 68in wide two roll calender, peripherally drilled rolls cross axis, bush type bearings, motorised nip adjustment with unidrive gearbox 277kW ASEA DC variable speed motor Hydraulic clamping device for extruder Set of 4 x cooling drums Dual wind up and liner applicator Chalking Unit Siemens PLC control. Complete line in excellent condition. PRICE: On request.

Qty 1 x Farrel Bridge 4 roll inverted L Lab calender, Roll width: 381 mm roll Ø: 152 mm Roller bearings Speed: 2,38 – 23,8   1/min., adjustable Nip adjustment: by hand Friction: 1:1 / 1:1,21 Drive: 9,25 kW, 380 V Measurement: ca. 1.765 x 1.687 x 1.800 mm (L x W x H) Weight: ca. 1.800 kg in. control cabinet

Farrel Bridge 12” x 6” Two Roll Mill Year (July) 1988 Crompton Parkinson Motor 380volts  ... mais informação

Collin Two Roll Lab Mill, Roll size: 150mm dia x 400mm wide Hydraulic nip adjustment, Model: WALZWERKE 150, Year of manufacture: 1988, Power: 19kW Electric roll heating with oil - operating temp 50 to 220 C Each roll variable speed from 0 -30 rpm Manual lubrication, programable controls. In very good condition. Manuals/drawings available.

available Cracker Mill Rolls dia 600 x 800mm Description attached!  ... mais informação

available 35" Mill on Baseframe more details in attached description!  ... mais informação