Fabricante:
(Categoria: 102)
bar material dia.:10 mmturning length:105 mmturning speeds:15.000 / 10.000 U/minnumber of tools:30 (3 x 10) driven tools:ja / yes control:FANUC 18i-TB total power requirement:3,5 kVAweight of the machine ca.:1,5 tdimensions of the machine ca.:1,9 x 0,8 x 1,7 mtoolpiece turning speed range:8.000 1/minmain spindle power:3,7 kWsub spindle power:1,1 kWCNC sliding headstock machine,subspindle,7 axis (X1, Z1, Y1, C1, X2, Z2, C2),barloader LNS TRYTON 112 A-B,Fireextinguisher KRAFT und BAUER,parts-ejector,coolant tank,machining with oil as coolant,reading hours:approx. 38.000 hours "machine on", approx. 27.000 hours "machining"
-DM 800 mm, turning length 5,000 mm, -Flood damage, control not affected, -equipped with 500 mm forkart lining, 2 Lynette DM, -Geom. very good condition, only used for fine work, renewal of the control recommended, very suitable for retrofit, Attention! This machine has already been dismantled and is in storage.
:SS-27 | SS-31 | SS-35 turning diameter:700|790|890 mmturning length:700/1200/1700/2200/3200/4200/5200 mmcontrol:Siemens 828D spindle nose:A2-11/A2-15/A2-20/A2-28/A2-32 spindle bore:153/230/255/318/360/410/535/610 mmspindle speeds:20-1200/16-700/13-600/14-450/12-400/10-350/8-300/4-220 1/minspeed steps work spindle:4-stufig (automatisch schaltend) cross feed:0,001~250 mm/minfeed in z-axis:0,001~400 mm/minrapid travel - longitudinal/face:8/10 m/mindia of ball screw:45 mm in X-Achse / 60 mm in Z-Achse tool turret:10- oder 12-fach tool taper:VDI 40/50 oder Schaftaufnahme tool holder -shaft diameter:32x32 mmdiameter tailstock quill:160 mm:200 mmtailstock quill taper MT:5 spindle drive:30/37 (37/45 opt.) kWservo motor X-axis:3,8 kwservo motor Z-axis:3,8 kwweight of the machine ca.:11t für Spitzenweite 700mm (weitere 500mm: 1,5t) tCNC controller:Siemens/Fanuc/Fagor steady rests:manuell und hyd ...
including quick-change chisel holders, 2 rotating centers ... mais informação
:SA-35 | SA-40 | SA-45 turning diameter:890|1020|1145 mmturning length:700/1200/1700/2200/3200/4200/5200 mmcontrol:Siemens 828D spindle nose:A2-11/A2-15/A2-20/A2-28/A2-32 spindle bore:153/230/255/318/360/410/535/610 mmspindle speeds:20-1200/16-700/13-600/14-450/12-400/10-350/8-300/4-220 1/minrapid travel - longitudinal/face:8/10 m/mincross feed:0,001~250 mm/min.feed in z-axis:0,001~400 mm/mindia of ball screw:50 mm in X-Achse / 80 mm in Z-Achse tool turret:10-/12-fach tool taper:VDI 40/50 oder Schaft tool holder -shaft diameter:32x32 mmdiameter tailstock quill:235 mm:200 mmtailstock quill taper MT:6 spindle drive:37/45 (50/60 opt.) kWservo motor X-axis:4,5 (6 opt.) servo motor Z-axis:4,5 (6 opt.) kwweight of the machine ca.:16,5t für Spitzenweite 700mm (weitere 500mm: 2,2t) tCNC controller:Siemens/Fanuc/Fagor steady rests:manuell und hydraulisch Solid slant bed esures the lathe´s accur ...
turning diameter:80 mmturning length:235 mmmax. bar capacity:42 mmpower capacity - driven tools:1 kWspeeds spindle 1:6000 1/minspeeds spindle 2:5000 1/minnumbers of turret head positions:8 posdrive capacity - spindle motor:SP1 11 / SP2 5,5 kWTools speed:60-6000 1/minweight of the machine ca.:ca. 3 tdimensions of the machine ca.:2,4 x 1,5 x 1,6 mHigh Performance CNC Turning- and Milling Center - chipconveyor- subspindle- live tools- C-axis- brake- partscatcher and partsconveyor- tool eye- barloader LNS HYDROBAR MINI-SPRINT approx. 5000 working hours
swing diameter:260 mmcontrol:840 D SIEMENSturning speeds:3.500 1/minspindle drive:36 / 28 kWchucking diameter:260 mmtravel -x axis:900 mmtravel -z axis:400 mmturret head:12 Pos.tool holder:VDI 40 rapid power traverse in X-and Z direction:100 / 30 m/mindimensions of the machine ca.:5,3 x 2,4 x 3,31 mCNC vertical lathe with 2 spindles,2x RÖHM power chucks dia. 315mm,
:SDM-1480Z | SDM-1680Z | SDM-1980Z | SDM-2080Z turning diameter over bed:1480|1680|1980|2080 mmturning diameter over slide rest:1000|1200|1500|1600 mmturning length:2000/3000/4000/5000/6000/8000/10000/12000 mmbed width:1100 mmworkpiece weight:12 (15 opt.) tspindle bore:130 mmspindle taper:140 spindle speed (3 steps):2,5-250 U/minmetrical thread cutting:1~120 (44 Arten) mmlongitudinal feeds:0.1 ~ 12 (56 Arten) mm/Uface feeds:0.05 ~ 6 (56 Arten) mm/Urapid traverse longitudinal:3400 mm/minrapid traverse cross:1700 mm/mincross way of carriage:760 mmmovement of the upper support:300 mmtool size:45 x 45 mmtailstock quill diameter:260 mmstroke:300 mmtailstock-quill conus:80 metrischspindle motor:30 (50 opt.) kWtool holder:4-fach steady diameter:500-800 mmCNC controls from:Siemens/Fanuc/Fagor payment: 100 % before loadingwarranty:12 months on parts onlyBRANDNEW conventional heavy duty center lat ...
:SDM 1000E | SDM 1250E | SDM 1400E turning diameter over bed:1000|1250|1400 mmturning diameter over slide rest:650|900|1100 mmturning length:2000/3000/4000/5000/6000/8000/10000/12000 mmmax. workpiece weight between centers:8000 kgbed width:755 mmspindle nose:A2-15 spindle bore:130 mmspindle speed (3 steps):3,15-315 U/minmetrical thread cutting:1~120 (56 Arten) mmcross way of carriage:520|680|720 mmmovement of the upper support:300|300|400 mmtool size:45 x 45 mmtailstock quill diameter:180 mmstroke:300 mmtailstock-quill conus:6 MKweight of the machine ca.:bei 3m: 12 t (jeder weitere Meter ca. 800kg) Machine size (LxWxH):bei 3m: 6100x1900x2000 mmtool holder:4-fach follower rest:50-220 mm4 jaw chuck:1000 mmsteady diameter:50-470 mmCNC controls from:Siemens/Fanuc/Fagor payment: 100 % before loadingwarranty:12 months on parts onlyBRANDNEW conventional heavy duty center lathe
turning diameter:33 mmturning length:330 mmcontrol: 840 total power requirement:20 kWweight of the machine ca.:6 tdimensions of the machine ca.:3850,2000,2100 m17 axes3 revolvers with the powered tools 1 gantry with the driven tools Main and counter spindle with C axesBarfeederMachine On-time 58,133 hours
Attention! This machine has already been dismantled and is in storage. ... mais informação
turning diameter:670 mmturning length:3000 mmcontrol:840 z-axis:3150/3000 mmy-axis:-125/+175 mmx-axis:700/260 X+ mmc-axis:0,001 °main gear-box motor:60/40 kWspindle turning speed range:2600/3300 U/minspindle diameter in front bearing:160 mmSpindle bore:115 mmlower slide:2 x 12, VDI 40 mmupper slide:25 kWno. of tools in the magazine:90 Stückworkpiece length:900 mmtool taper:HSK 100 / VDI 40 rapid traverse::15/20 m/mintotal power requirement:140 kWweight of the machine ca.:35 tdimensions of the machine ca.:13 x 4,5 x 3,6 mCNC TURNMILL center with opposed spindles and 2 saddles, used for Alu operation only- SIEMENS 840 C control for 8 axis- Left/Right spindle with C-axis, KNCS 400 mm power chuck- Lower saddle with 2 x 12-fold revoving heads- Turning.- boring,- milling unit on top saddle, HSK 100 tool taper, 25 kW drive motor, 10-4000 r/min, B and Y axis- Coolant device with 80 bar and ro ...
:KDM-K 12| KDM-K 16 | KDM-K 20 | KDM-K 23 | KDM-K 26 faceplate diameter:1000|1400|1800|2000|2300 mmswing diameter:1200|1600|2000|2300|2600 mmturning height:1000|1250|1400|1600|1500 mmtable speeds:6,3- 200|5-160 | 3.2-100 | 5-160 | 2,5- 80 m/mintransmission ratio:16 max. workpiece weight:3,2|5|8|8|8 trapid feed of tool post:1800 mm/minfeed speeds:0,8-86 mm/min in X-AchseTravel of Ram (vertical):650/700|800/1000|800/1000|800/1000/1300|1000/1380 mmTravel of ram (horiz.):630|915|1115|1250|1500 mmmax. vertical adjustment of side-support:900|900|980|980 mmmax. horizontal adjustment of side-support:630|630|500|500 mmCross rail travel :850/1100|890/990/1240/1640|1240/1640 mmpower maindrive:22|30|37|37 kWweight of the machine ca.:9|14|18|23|21 tMachine size (LxWxH):2299x2540x3403|2660x26603698|3135x3070x3910|3380x3360x4300|390 0x2950x4400 mmtool holder:5 fach:LED 4 jaw chuck:mit 4 Klauenkläst ...
turning diameter over bed:350 mmturning diameter over slide rest:240 mmturning length:800 mmSpindle RPM:40 - 2000 in 8 Stufen 1/mintotal power requirement:3 kWSpindle bore:26 mmtailstock quill taper MT:MK 2 dimensions of the machine ca.:1,5 x 1,0 x 1,6 mweight of the machine ca.:1,9 tVery well maintened center lathe with accessories- 3-jaw, 4-jaw chuck- tailstock with center- 1 boring head- RAPID quick tool change device with 3 holder- saddle mounted steady rest- collant device- set of collets appr. 75% size B 32
:KHL-160 | KHL-180 | KHL-200 | KHL-220 turning diameter over bed:1600|1800|2000|2200 mmturning diameter over slide rest:1250|1450|1650|1850 mmturning length:3000/4000/5000/6000/8000/10000/12000/14000/16000 mmbed width:1600/2100 mmworkpiece weight:32t (40t,64t, 80t Option) spindle bore:85 mmspindle taper:120mm taper 1:7 number of spindle speeds:0.86-160 U/minmetrical thread cutting:2-40 mmrange of module thread:1.5-20 mmlongitudinal feed:0.125-4.8 mm:0.063-2.4 mmmovement of the upper support:quer: 700mm/900mm movement of the upper support:längs: 600 mmturning tool - shaft cross cut:70x70 diameter tailstock quill:300/500 mmtaper of tailstock:100 taper 1:7 quill stroke:300 mmsteady rest close/open:400-750/650-1200 mmmain drive motor:80/110 kW4 jaw chuck diameter:1000 - 1600 mmsteady rest diameter:400 - 750 mmopen steady:650-1200 mmCNC controls from:Siemens/Fanuc/Fagor
:LL 550 | LL 750 | LL950 turning diameter:550 | 750 | 950 mmturning length:3000/4000/5000/6000/7000/8000/9000/12000/14000 mmcontrol:Siemens/Fanuc/Fagor center height over bed:475|575|675 mmbed width:990 mmspindle bore:153/230/305/405 mmspindle nose:A2-11/A2-15/A2-20/A2-28 spindle speed:9-600/9-500/7-400/5-250 U/minspindle taper:6 MKspindle drive:22/26 (30/37 opt.) kWtool turret:4/8/12 hydraulisch oder elektrisch tool holder -shaft diameter:32 (40 opt.) mmtailstock quill diameter:165|200 mmtailstock quill adjustment:250 mmtaper in tailstock:6 MKtailstock movement:über Motor travel -x axis:370 | 480 mmtravel - z:= Spitzenweite mmservo motor X-axis:3 | 4 kwservo motor Z-axis:4 | 7 kwrapid power traverse in X-and Z direction:5/4 m/minhydraulic motor:2,2 (2,9 opt.) kWcoolant pump drive:3 (15 opt.) | 15 barweight of the machine ca.:12,7/15,3/18/21,5/24/26,6 | 13,7/16,4/19/22,2/25/27,6/30,2 ...
faceplate diameter:2000 mmswing diameter:2130 mmturning height:1400 mmram stroke range:1000 mmworkpiece weight:10 tfaceplate turning speed range:1 -200 U/minmain drive:60 kWtotal power requirement:95 kWweight of the machine ca.:24 tdimensions of the machine ca.:6,0 x 4,0 x 5,6 mwith CNC SIEMENS 840 DC-axis driven tooling 15/22 kWautomatic toolchnager 16-pocketsthrough spindle coolantsplash guarding and chip conveyor
:LL-1250 | LL-1450 | LL-1650 turning diameter:1250 | 1450 | 1650 mmturning length:5000/6000/7000/8000/9000/12000/14000/16000 mmcontrol:Siemens/Fanuc/Fagor center height over bed:705|805|905 mmwidth of cross cariage:600 mmbed width:1370 mmspindle bore:200 mmspindle nose:A2-15/A2-15/A2-20/A2-28 spindle speed:4-400 U/minspindle taper:6 MKspindle drive:22/26 (30/37 opt.) kWtool turret:4/8/12 hydraulisch oder elektrisch tool holder -shaft diameter:40 mmtailstock quill diameter:300 mmtailstock quill adjustment:250 mmtaper in tailstock:7 MKtailstock movement:über Motor (Zahnstangenantrieb) travel -x axis:755 mmtravel - z:= Spitzenweite mmservo motor X-axis:4 kwservo motor Z-axis:7 kwrapid power traverse in X-and Z direction:5 m/minhydraulic motor:1,4 (ab 9m: 3,6) kWcoolant pump drive:15 barweight of the machine ca.:auf Anfrage machine length:15150/16150/17150/18150/19150/20150 mmmachine width ...