máquinas de borracha usadas para venda

Strip cooling system system Cantilever, built in 2004, strip width 2-fold up to 120 mm, 1-fold up to 200 mm, thickness 6 to 12 mm, Throughput 500 to 800 kg/h ... mais informação

Powder machine PM 1000 Z , Fabr. PEKU / Germany ... mais informação

Fine trainer system from UTH, type Roll-Ex 70 TRF ... mais informação

cold feed pin extruder, EEK 125.10 M, piebald speed 10 to 60 rpm, drive 135 KW AC, ... mais informação

Pin-Convert-Extruder, GE 120 SC, make Berstorff, cold lined ... mais informação

Profile extruder, GE 90 x 16 D vacuum, make Troester, cold lined ... mais informação

ROLL DIAMETER 550 mm POLL WORKING LENGTH 1530 mm MOTOR POWER 110 KW DIMENSIONS: 630022301830 (L×W×H) SPEED RATIO OF ROLLS 1:1.27 Structure description 1 Base frame is welded and annealed . 2 The motor is 3- phase asynchronous motor, protection levels :IP54. 3 The driving type :Single out- shaft or double out- shaft. The speed reducer is hard gear reducer,which has long service life and low noise. 4 The roller bearing is rolling bearing with Low noise, save power almost 20%. the roller bearing use grease lubricating. 5 The nip adjusting Motor type 6 This machine is equipped with two pieces of moving blade. 7 Safety device : Pull the safety rod to achieve emergency stop. It can be installed with kick stop device and emergency stop device for safety. 8 The electrical design theory conform to the TWO ROLL MILL specifications strictly . It is equipp ...

5501500 TWIN SCREW 1. 1 PC 5501500 OPEN MILL RUBBER MIXER 2. 1 PC 5501500 OPEN MILL RUBBER MIXER 3. ELECTRIC CONTROL CABINET WITH DRIVER 4. DIRECT CONNECTION (COUPLED) 5. BRONZE BEARINGS 6. AUTOMATIC LUBRICATION 7. 160 KW 990r/min  ... mais informação

L/D=20.7 External dimensions 2700×1000×1400(LxWxH) Screw stiffness HRC65-68 Screw diameter 90mm Engine power 30KW/1470rpm SCREW LENGTH 1860 mm Heating section number/power 6kw×2  ... mais informação

ROLL DIAMETER 400mm POLL WORKING LENGTH 1000mm MOTOR POWER 45 KW DIMENSIONS: 447118501760 (L×W×H) SPEED RATIO OF ROLLS 1:1,27 Structure description 1 Base frame is welded and annealed . 2 The motor is 3- phase asynchronous motor, protection levels :IP54. 3 The driving type :Single out- shaft or double out- shaft. The speed reducer is hard gear reducer,which has long service life and low noise. 4 The roller bearing is rolling bearing with Low noise, save power almost 20%. the roller bearing use grease lubricating. 5 The nip adjusting Motor type 6 This machine is equipped with two pieces of moving blade. 7 Safety device : Pull the safety rod to achieve emergency stop. It can be installed with kick stop device and emergency stop device for safety. 8 The electrical design theory conform to the TWO ROLL MILL specifications strictly . It is equipped  ...

Roll cooling: Rotary joints Speed: Fixed speed, not variable Back roll: 14.7 min-1 = 27.7 m/min Front roll: 17.8 min-1 = 33.6 m/min Friction: 1 : 1,21 – fixed friction ratio Roll bearings: 4 NEW anti-friction roller bearings Lubrication: Lubrication points Nip adjustment: Manual adjustment by lever Overload protection: Breaking plates Stock guides: Steel brackets, left side with hydraulic lateral movement; both sides pneumatically retractable Material tray: Steel tray underneath the rolls Strip cutter: 3 pneumatically retractable cutting knives; 2 knives with motorized width adjustment Motor: Siemens AC motor 132 kW, 380/660 V, 50/60 Hz, 1480 min-1 Gear reducer: Flender straight bevel gear pair Coupling wheels: Herringbone gearing, very good condition Pinion: Herringbone gearing, very good condition Electric controls: Conventional contactor controls year  ...

Press 800 x 1000 Clamping force cca 3000kN Electric heating ... mais informação

Press 800 x 800 clamping force cca 3000kN electrical heated  ... mais informação

BERSTORFF GmbH Mixing mill for all types of rubber compounds Roll width 120 cm Roll diameter 55 cm Machine in very good condition !  ... mais informação

Francis Shaw KO Intermix Year: Jan 1987 Approx. mixing capacity 1.8 litres Mawdsley DC motor, shunt wound, serial no. 180T827, 30kW, 460 volts, 74 amps, 1800rpm, continuous rating Apex Denison Hydraulic Pump Holroyd Gearbox Barco Rotary Joints Fortress Interlock system Water steam inlet Water steam drain Mixing Chamber Rotors Plunger Drop Door Grease points With Hopper Thorn EMI electronic star drive; 415 volts, 3 wire, 50 cycles, 54kva, November 1987 Operator Panel consisting of rotor speed, main motor current process timer, mix temperature Complete with control panel

GK90E Mixer Manufacturer : Harburg Freudenberger Maschinenbau Machine type : Internal mixer Model number : GK 90 E Year of construction : 1987 Chamber volume : 90L Standard rotor speed: 10-50 1/min. Rated motor power : 440KW. Main drive 1850 A Rotor geometry : PES-5 Machine parts : Baseplate Mixer Body Feeding hopper Pneumatics system Gearbox KWE Couplings ESCO Gear CST 220 Complete with motor Main drive Leroy Somer Hydraulic unit Gearbox Lubrication unit Dust seals Lubrication unit Grease pump PLC Advise 2.0 (control cabinet) without server

Betol PVC Extrusion Line Type BC50 0-100rpm 4x Eurotherm barrel controllers Start / Stop Stainless Steel Water trough Width 200mm x 36” Comes out hot and goes through tunnel which cools it down and turns it rigid and into a Haul Off  ... mais informação

Heated Bonding Press Manuf.: Paul OTT Model JU3013 415v 51kW (Tech data attached)  ... mais informação

GK 260N Mixer Manuf.: Werner & Pfleiderer Rotor type ZZ2 Type N tangential Ram Pneumatic pressure 10 bar Camber volume 255 litres Useful volume 220 litres Grease lubrication Dust seal lubrication Stainless steel hopper replaced in August 2011 Pneumatic ram replaced in May 2022, New piston rods, sealings Gearbox Coupling shafts between the mixer and the gearbox Hydraulic central unit With Grease and Oil lubrication pumps The machine was used on natural rubber, NBR and EPDM

LBBC Steam Autoclave 800mm diam. x 1.2m long Quick Lock Door Hydraulic Test Pressure 180psi Safe Working pressure 120psi Welded construction  ... mais informação