Fabricante:
(Categoria: 307)
HUSKY Injection Machine Type H400 400 tonne Hydraulic Pressure 180 BAR max Weight 18,143 kg CE marked Year: 2003 ... mais informação
clamping force: 450 kNinjection volume: 135 cm³screw diameter: 35 mmplaten size: 600 x 400 mmCondition: used,Specification: C-frame injection moulding machine for TPE - usedclamping unit:- clamping force: 450 kN- heating platen size: 600 x 400 mm- sliding table: yes- Clamping direction: from below- Ejector / lifter: Up + LoInjection unit:- Injection volume max.: 135 cm³- Screw diameter: 35 mm- Connected load: 3x 400 V, 50 Hz- Weight approx.: 5,500 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cross-section width:: 40 (45) mmcross-section heigth:: 25 mmfeed:: 1 - 999.999,9 mmspeed of feed:: 1 - 60 m/mincuts max.:: 100 Schnitte/mCondition: used,Specification: circular knife cutting machine - second-hand for cutting rings, discs and profiles- diameter max.: 45 mm- 3 hoses or strands: 6 - 20 mm- 2 hoses or strands: 20 - 30 mm- 1 hose or string: 30 - 45 mm- cross section width max.: 40 mm- cross-section height max.: 25 mm- feed speed: 1 - 60 m/min, infinitely variable- Cutting capacity max.: 100 cuts/min depending on material and cutting length- Cutting length: 1 - 999.999,9 mm- Step jump: 0.1 mm- Feed by servo drive- Cutting by servo drive- Pulsed feed- Connected load approx.: 5 kW- Operating voltage: 3 x 400V, 50Hz, PE- Weight approx.: ...
Tyre testing machine - static balancer for passenger tyres. Tyre size from 15 "to 18" (20") CE certified More details see the attached description! ... mais informação
clamping force: 1.013 kNinjection volume: 400 cm³screw diameter: 25 mmplaten size: 335 x 400 mmCondition: used,Specification: injection moulding machine for rubber - usedclamping unit:- clamping unit: vertical- clamping force: 1.013 kN- size of heating platen: 335 x 400 mm (standard) core turning unit Injection unit:- screw diameter: 25 mm- Barrel diameter: 51 mm- Injection volume max.: 400 cm³- Injection pressure: 1,500 bar- Connection value: 3x 400 V, 50 Hz 42A fuse protection (incl. periphery)- Electrical power: 29,1 kVA- Control: G8 Control- Hydraulics: 250 bar (tank 200 litres)- Further connections: Cooling water inlet/outletDimensions L/W/H approx.: 2,300 x 3,400 x 2,250 mmWeigh ...
screw ø:: für Extruder 90 mmscrew length:: -- screw speedl:: -- U/mindrive power:: 13,6 kWCondition: little used, as good as newSpecification: gear pump ZP 75/50 for extruder size 90- SEW helical gear units: R 97- Siemens direct current motor: 1 GG5 118- Drive power: 13.6 kW, 57 A- curved tooth coupling- With clamp for the head connection,- Clamping flange for extruder and head connection,- Base plate with linear guide rails,- Tooth shaft diameter: 75 mm- tooth width: 50 mm- helical gearing, hardened steel bearings, right-hand drive- without controlThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
1 x Smit 660mm dia x 2100mm wide two roll mill, Rebuilt 2005, manual nip adjustment, Lunn type safety bars, Back roll surface fluted, Front roll smooth finish. Bush type bearings with flood lubrication, compact \Jahnel\ right angle drive gearbox. with 180KW DC variable speed motor and controls. Strip knives to front roll. Heavy duty 2 part bedplate. Extra Information: Front roll 29 teeth Back (fluted roll) 32 teeth Friction ratio 1:1.1 Motor 180kW DC variable speed, 1300rpm, Gear box ratio 1:9.8 Bullgear 122 teeth, Pinion gear 18 teeth (Ratio 1:6.777) Therefore approx roll speeds as follows: Input motor speed 1300rpm: Front roll 21.53 rpm Back (fluted) roll 19.6 rpm
machine measurements: -- mmmachine weight: -- kgpower capacity: -- kWCondition: usedSpecification: dosing unit type SiloStar 922 A - second-hand- for dosing liquid silicone LS- container: 20 litre hobbocks and 200 litre drums- Power connection: 400V, 50Hz Equipment of the plant with:- Fardoser SPS P1- Mixer / material pressure regulator cooled with outlet valve- roll-in device- Pressure and material shortage protection- Machine connection outlet valve and pressure regulator- Pressure vessel ColourThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
LWB Steinl Injection Machine Type VCE -T 500/160 T Clamp power 500 KN Injection volume 160 cm3 Year 2006 6 Bar 400 v 50 hz 26 KW ... mais informação
LWB Steinl Injection Moulding Machine Model VCE-T-TPE-EPDM 100 ton capacity ECO touch screen control ... mais informação
Berstorff Strainer Extrusion Line Consisting of: Extruder Supplier Berstorff Type GE 150KSx16D Year of construction 2007 Pins: 12 Pins per level: 8 Condition: good Weight approx. 10000 kg Screen change: hydraulic, bladder accumulator 20lt / 300Bar D = 200mm Gear pump Supplier: Maag Pump Systems Type: extrex® 110-5 RV Volume 716 cm³ / rev Year of construction 2013 Condition: good Heaters Supplier: Regloplas Type P140 Year of construction various Number 5 pcs. Cooling bath Cooling medium Water above, 2 rows below with 4 fans each Year of construction 2006 Condition: good Dimensions 9m Weight approx. 500 kg Especially 8 fans Installation tape Year of construction 2006 Condition: good Weight about 300 kg
1 x Buzuluk 240 litre Internal mixer Model: 14630, year: Dec 2008 (body and hopper), Batch size: 200 kgs, Drilled sides, Self sealing type dust seals, Oil injection, Hydraulic drop door with linear actuator and toggle latch, Stellite faced drop door, Two wing tangential rotors. 20in pneumatic hopper. 3 zone TCU Full unidrive gearbox (Make Skoda), with 630kW, 6000V, 739rpm, 73.5A slip ring motor and Oil filled starter. In very good condition.
Prodicon Batch Off Unit 500mm sheet width Inlet speed 0-10m/minute Sheet thickness 5-12mm No. of cooling sections 3 No. of fans 9 Complete with electrical control panel. Year 2009 ... mais informação
Berstorff Three Roll Calender Manufacturer: Krauss Maffei Berstorff 2650mm wide x 650mm (26”) diam. Effective working width 2600mm (Roller Head Die Width) Rolls Configuration: ‘I’ shape Rolls Type: Peripherally Drilled Drive: Right Hand Transmission: Direct Drive by Cardan Shafts Motors: 3X 75 KW, 2600 RPM, 50 Hz Nip Adjustment: Hydraulic (Berstorff patented) Fixed roll: Roll 2 (middle roll) Adjustable roll: Roll 1 and 3 (upper and lower roll), Max Roll gap is 80 mn Cross axis: Roll 1, 2 and 3, Hydraulic operated, max. 25 mm Pre-loading & Roll Bending: Available Rolls Speed: Variable, 0.5-10 m/ min Bearings: Antifriction Roller Bearings Electricals/ Controls: PLC Complete with motor and controls Year 2009
1 x Farrel F370 mixer chamber and hopper M/c no. 081110, Date: November 2009, SSA dust stops, 4 Wing Rotors, Drop door with Linear actuator, Base Plate with Toggle Latch. Pneumatic hopper with extension neck (Floating weight looks to be in good condition). Parts available: Body, baseplate, Toggle Latch, actuator and Pneumatic hopper with extension neck.
Tabletop cutting plotter with the following equipment: - 2 Z-axes for 2 tools (one for knives and one for milling motor, currently no milling motor installed but only knives) - oscillating blade, pneumatically driven - Vacuum table with automatic field control - 2 pieces of adjustable vacuum pumps - All axes with servo drive - Auto-nesting software module - Interactive layout software module for manual positioning of the contours to be cut - 3 tool heads for blades thickness: 1x 0.64mm blades, 1x 1.0mm blades, 1x 1.5mm blades
Berstorff 6inch (150mm) Strainer Extruder Manufactured by: Krauss Maffei Berstorff Model: GE 150 K Screw Diameter: 6"/150 mm L/D Ratio: 6 Speed: Variable, up to 45 rpm Motor: 90 KW, 1500 RPM Transmission: Direct Drive, 3 steps reduction Gear Reduction Ratio: 33:1 Year 2009 ... mais informação
Berstorff 8inch (200mm) Cold Feed Pin Extruder Manufactured by: Krauss Maffei Berstorff Extruder Type: Vac GE 200 SC, Pin Type No of Pins: 2 X10 + 1X12 (Hydraulic adjustment) Screw Diameter: 8"/200 mm L/D ratio 18:1 Drive: 300 Kw, 1500 RPM Screw speed: 33pm Complete with Control Panel Roller Die Suitable for rubber compounds Year 2009
LWB Steinl Injection Machine Type VREFE 1600/1000/170 Heating platen size 500 X 510 X 63 mm Sliding platens Top and bottom ejectors Clamping force 1600kN Opening force clamp 100kN Clamping stroke 395mm Injection volume E 1000 ccm Max. Injection Pressure E 2200 bar Injection volume EF 170 ccm Max. Injection Pressure EF 1800 bar Hours: 700 since new Year 2009 Weight 6000kg