used alzmetall automatic drillers

Alzmetall AB4SJ Tool holder MK4 automatic feed with 3 feed speeds 2 shoot stages and infinitely variable speed control right left barrel, thread cutting device Cooling agent device in the foot Round table with holes without rev counter Machine hood modern made of plastic with cracks and loechers Speed: 80-710 rpm Table diameter: 450 mm Max distance from spindle to foot: 1200 mm Extension to center spindle: 170 mm Machine hoe approx. 200 cm Bt323s8 SPECIAL PRICE due to visually poor condition according to photos, technically usable condition, the drill is not locked at the shaft drill spindle tool holder in the rotational motion (see photos). If the drill is not firmly in the drill spindle, it rotates through. Special price

Alzmetall AB4SJ Tool holder MK4 automatic feed with 3 feed speeds 2 shoot stages and infinitely variable speed control right left barrel, thread cutting device Cooling agent device in the foot Round table with holes without rev counter Machine hood modern made of plastic with cracks and loechers Speed: 80-710 rpm Table diameter: 450 mm Max distance from spindle to foot: 1200 mm Extension to center spindle: 170 mm Machine hoe approx. 200 cm Bt323s8 SPECIAL PRICE due to visually poor condition according to photos, technically usable condition, the drill is not locked at the shaft drill spindle tool holder in the rotational motion (see photos). If the drill is not firmly in the drill spindle, it rotates through. Special price

see side sheet below, with 2-spindle drill head Franz X. LINDNER SBS-2/2, spindle distance 300 mm, (translation 1:1)

with NC round table WALTER 1000 mm, see pictures

Drilling capacity in steel / cast iron 50/65 mm Drilling capacity in steel 70 mm Feed 0.1 - 0.54 mm / Rev Speed 62-1240 RPM Recording MK 5 spindle stroke (drilling depth) 240 mm Usable projection 385 mm Table 800 x 680 mm Spindle head diameter 70 mm Height 2350 mm the machine

Morse cone MK 3 Drilling performance: Steel 28 mm Casting 32 mm Ihivikt Extension 700mm 3 Pre-shed0.1 - 0.2 - 0.3 mm/U 15 Spindle speeds 50 - 1220 rpm Spindle stroke 165mm max. distance spindle - base plate 1300 mm max distance spindle clamping block approx. 800mm Dimensions clamping cube 470mm*550mm*500mm high Clamping area foot 870*700mm Hoe adjustment boom approx. 620 mm Spindle motor 1.1 / 1.7 kW Lifting motor 0.55 kW Outside mass: Length 1400 mm; width 700 mm; height 2300 mm Weight approx. 1100 kg

High-performance column drilling machine Offer number: 17469 Make: ALZMETALL Type: AB 4 SV Machine No: 18498 Built: 1987 Technical data: - Drilling capacity in steel ST 60 40 mm - Drilling capacity in steel ST 60 50 mm - Thread cutting device - Drilling spindle holder MK 4 - Drilling spindle stroke 180 mm - Drilling spindle speeds infinitely adjustable with pre-bedding - Level 1 - 80 - 210 rpm - Level 2 - 210 - 765 rpm - Extension 330 mm - 3 feeds 0.1 - 0.2 - 0.3 rpm - hydr. Feed cylinder for semi-autom. Workflow + Rapid Response - Table with 2 T-slots 720 x 360 mm - height-adjustable via rack with hand crank - max. distance table - drilling spindle approx. 780 mm - maximum distance machined base plate - drilling spindle 1250 mm - Lighting - Coolant device - Swivel arm control panel - Drive 400 V 4 kW - Space requiremen ...

Technical data: - Drilling capacity in steel ST 60 40 mm - Drilling capacity in steel ST 60 55 mm - Thread cutting device - Drilling spindle holder MK 4 - Drilling spindle stroke 180 mm - Extension 350 mm - Height-adjustable with 2 T-slots 720 x 560 mm - max. Distance table - drilling spindle 550 mm - max. Distance machined base plate - drilling spindle 1140 mm - Column diameter 200 mm - Feed-electromagnetic 0.15 0.2 - 0.3 - 0.36 mm/U with overload protection - Drilling spindle speeds infinitely adjustable 60 - 210 + 210 - 765 rpm - Drive 400 V / 2.3 / 3.4 kW - Lighting - Quick-release drilling chuck - Space requirement approx. W 750 x H 2050 x D 1050 mm - Weight approx. 850 kg

- mounting table: 300 x 400 mm - quill ram: 120 mm - speed range: 5800 rpm - gearbox stages: 2 - feed: 0,001 - 3,5 m/min - rapid: 3,5 m/min - taper fixture: MK 3 - thread cutting device with foot switch - coolant system - total power: 1,5 kW - weight of machine: 380 kg - space requirement (W x D x H): 0,66 x 0,44 x 1,95 m - condition: very good Details High-performance drilling machine, machine number 511 accessories documentation, coolant equipment

Drilling capacity: 32 mm Throat: 0 mm Spindle taper: 150   MACH-id    5460 MAKE        Alzmetal TYPE          Alzrapid 32 YOP             1998 SPECIFICATIONS Max. drill Ø steel      32 mm Max. drill Ø cast       40 mm Max. tap Ø      24 M Arm Length    725 mm Stroke pinole        150 mm Throat       400 mm Spindle Taper      4 ISO/Bt/Mk Speeds / ranges        3000 Rpm Table Length        1175 mm Table Width          525 mm Power       3 kW DIMENSIONS Length        2600 mm Width         2000 mm Height    &n ...

Drilling capacity in St 60: 40 mm threading in St 60: M 24 mm threading in GG 20: M 30 bore stroke: 120 mm Short spindle: MK 3 throat: 293 mm column diameter: 115 mm Machine table - usable table surface: 514 x 360 mm T-Slots Amount - Width - Distance: 2 x 14 x 224 mm Distance spindle - machine table min./max.: 117 / 701 mm feed: 0,10 + 0,20 mm/U spindle turning speed range: 160 - 2250 UpM total power requirement: 1,45 / 1,9 kW height of the machine: 1840 mm weight of the machine ca.: 285 kg Standard equipment: - Mushroom pushbutton (latching) for EMERGENCY STOP - Reversing switch for right-left rotation - Motor protection switch - Speed adjustment stepless - Speed display digital - Feed overload protection - Protection IP 54 - Connector (fully assembled, cable length 2 m) - Spindle protection with electrical protection Pos. 25 Coolant device B, consisting of: separate container (33l), Pu ...

: 34 mm : 40 mm : 40 mm : MK 4 : 100-1.800 U/min. throat: 300 mm : 615x430 mm : 2 x 14 x 224 mm : 138/688 mm column diameter: 145 mm spindle stroke: 160 mm feeds: 0,1-0,2-0,3-0,4 mm/U Machine height: 1865 mm total power requirement: 1,4/2,2 kW Standard equipment: - Electromagnetic feed clutch with overload protection and electrical Cross Handle Switches - Main switch lockable - Motor protection switch - Mushroom pushbutton (latching) for EMERGENCY STOP in the front panel - Speed adjustment stepless - Speed display digital - Protection class IP 54 - Motor insulation class F - Spindle protection with electrical protection Pos. 20.1 Tapping device with foot switch, for thread cutting with Stop, max. 6 threads/min., (Tapping power dependent on spindle speed) Pos. 25. Coolant device B, consisting of: separate container (33 l), pump with Motor protection switch, complete fitting The data for ...

: 12 mm : M 10 : B 16 : 250 - 5000 U/min. spindle stroke: 40 mm throat: 200 mm column diameter: 50 mm : 2 x 12 x 80 mm : 300x240 mm : 2 x 12 x 80 mm : 110 / 250 mm feed: von Hand : Handrad Machine height: 670 mm total power requirement: 0,7 kW weight: 64 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Drilling capacity in St 60: 30 mm threading in St 60: M 16 threading in GG 20: M 20 Short spindle: MK 3 bore stroke: 140 mm throat: 293 mm column diameter: 115 mm Machine table - usable table surface: 514x360 mm T-Slots Amount - Width - Distance: 2 x 14 x 224 mm Distance spindle - machine table min./max.: 132/724 mm feed: Hand spindle turning speed range: 225-4300 UpM height of the machine: 1790 mm total power requirement: 1,0/1,6 kW weight of the machine ca.: 260 kg Standard equipment: - Mushroom pushbutton (latching) for EMERGENCY STOP - Reversing switch for right-left rotation - Motor protection switch - Speed adjustment stepless - Speed display digital - Protection IP 54 - Connector (fully assembled, cable length 2 m) - Spindle protection with electrical protection The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Drilling capacity in St 60: 40 mm threading in St 60: M 24 threading in GG 20: M 30 Short spindle: MK 3 bore stroke: 120 mm throat: 293 mm column diameter: 115 mm Machine table - usable table surface: 514x360 mm T-Slots Amount - Width - Distance: 2 x 14 x 224 mm Distance spindle - machine table min./max.: 117/701 mm feed: 0,10 + 0,20 mm/U spindle turning speed range: 160-2.250 UpM total power requirement: 1,45/1,9 kW height of the machine: 1840 mm weight of the machine ca.: 285 kg Standard equipment: 7 TFT - LCD display with touch function: manual input of spindle speed Setpoint, speed display actual value, integrated drilling depth display with touch Zero point transfer, virtual drilling depth scale in the display, machine Status displays and warnings in the display, service information, selectable User language: DE / EN / FR / ES / IT / NL / RU Pos. 37.5 Technology computer in the disp ...

: 18 mm : M 12 : M 14 : MK 2 : 225-4.300 U/min. spindle stroke: 80 mm throat: 190 mm column diameter: 65 mm : 300x240 mm : 2 x 12 x 80 mm : 75/357 mm : 300x240 mm : 2 x 12 x 80 mm : 437/437 mm feed: von Hand : Handkurbel total power requirement: 0,37/0,55 kW Machine height: 840 mm weight: 110 kg Standard equipment: - Main switch with motor protection switch lockable - Reversing switch for clockwise and anti-clockwise rotation - Speed adjustment stepless - Protection IP 54 - Mushroom pushbutton (latching) for EMERGENCY STOP - Spindle protection with electrical protection The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 14 mm : M 10 : MK 2 : 230-4.000 U/min. spindle stroke: 80 mm throat: 190 mm column diameter: 65 mm : 300x240 mm : 2 x 12 x 80 mm : 75/357 mm : 300x240 mm : 2 x 12 x 80 mm : 437/437 mm feed: von Hand : Handkurbel Machine height: 825 mm total power requirement: 0,7 kW weight: 83 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 26 mm : 30 mm : 30 mm threading in St 60: M 20 threading in GG 20: M 24 : MK 3 : 120-2.200 U/min. throat: 293 mm : 514x360 mm : 2 x 14 x 224 mm : 90/675 mm column diameter: 115 mm spindle stroke: 160 mm feeds: 0,1-0,2-0,3-0,4 mm/U total power requirement: 1,0/1,6 kW Machine height: 1865 mm weight: 380 kg Standard equipment: 7 TFT LCD display with touch function: manual input of spindle speed Setpoint, actual speed display, integrated drilling depth display with touch Zero point transfer, virtual drilling depth scale in the display, machine Status displays and warnings in the display, service information, selectable User language: DE / EN / FR / ES / IT / NL / RU - Thread cutting device, for thread cutting with stop, max. 6th Thread / min (thread cutting performance dependent on spindle speed), thread depth adjustable via depth stop and in the TFT - LCD display (4 tools) - Infinitely va ...

: 16 mm : M 12 : MK 2 : 100-2.000 U/min. spindle stroke: 80 mm throat: 190 mm column diameter: 65 mm : 300x240 mm : 2 x 12 x 80 mm : 75/357 mm : 300x240 mm : 2 x 12 x 80 mm : 437/437 mm feed: von Hand : Handkurbel Machine height: 825 mm total power requirement: 0,7 kW weight: 83 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 40 mm : M 24 : M 30 : MK 3 bore stroke: 120 mm throat: 293 mm column diameter: 115 mm : 514x360 mm : 2 x 14 x 224 mm : 117/701 mm feed: 0,10 + 0,20 mm/U spindle turning speed range: 160-2.250 UpM total power requirement: 1,45/1,9 kW height of the machine: 1840 mm weight of the machine ca.: 285 kg Standard equipment: - Mushroom pushbutton (latching) for EMERGENCY STOP - Reversing switch for right-left rotation - Motor protection switch - Speed adjustment stepless - Speed display digital - Feed overload protection - Protection IP 54 - Connector (fully assembled, cable length 2 m) - Spindle protection with electrical protection The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 23 mm threading in St 60: M14 threading in GG 20: M16 : MK 2 spindle stroke: 100 mm : 125-2400 U/min. throat: 250 mm column diameter: 90 mm : 370x300 mm : 2x14x160 mm distance spindle /table: min./max. 125/455 mm : Handkurbel : 320x250 mm : 2x14x160 mm : 625/625 mm feed: von Hand height of the machine: 1095 mm weight of the machine ca.: 160 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 26 mm : 30 mm : 30 mm : M 20 : M 24 : MK 3 : 120-2.200 U/min. throat: 293 mm : 515x360 mm : 2 x 14 x 224 mm : 90/675 mm column diameter: 115 mm spindle stroke: 160 mm feeds: 0,1-0,2-0,3-0,4 mm/U Machine height: 1865 mm total power requirement: 1,0/1,6 kW Standard equipment: - Electromagnetic feed clutch with overload protection and electrical Cross Handle Switches - Main switch lockable - Motor protection switch - Mushroom pushbutton (latching) for EMERGENCY STOP in the front panel - Speed adjustment stepless - Speed display digital - Protection IP 54 - Motor insulation class F - Spindle protection with electrical protection Pos. 20.1 Tapping device with foot switch, for thread cutting with Stop, max. 6 threads / min., (Tapping power dependent on spindle speed) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 34 mm : 40 mm : 40 mm threading in St 60: M 24 threading in GG 20: M 30 : MK 4 : 100-1.800 U/min. throat: 300 mm : 615x430 mm : 2 x 14 x 224 mm : 138/688 mm column diameter: 145 mm spindle stroke: 160 mm feeds: 0,1-0,2-0,3-0,4 mm/U total power requirement: 1,4/2,2 kW Machine height: 1865 mm weight: 470 kg Standard equipment: 7 TFT LCD display with touch function: manual input of spindle speed Setpoint, actual speed display, integrated drilling depth display with touch Zero point transfer, virtual drilling depth scale in the display, machine Status displays and warnings in the display, service information, selectable User language: DE / EN / FR / ES / IT / NL / RU - Thread cutting device, for thread cutting with stop, max. 6th Thread / min (thread cutting performance dependent on spindle speed), thread depth adjustable via depth stop and in the TFT - LCD display (4 tools) - Infinitely v ...

: 40 mm bore capacity in cast iron: 46 mm : 50 mm : M 30 : M36 : MK 4 throat: 300 mm : 100-1600 U/min. : 615x430 mm : 2x14x224 mm Distance spindle/table max.: 147/688 mm column diameter: 145 mm spindle stroke: 160 mm feeds: 0,1-0,2-0,3-0,4 mm/U height of the machine: 1885 mm drive motor: 1,8/2,9 kW weight of the machine ca.: 450 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 1200 mm y-travel: 600 mm z-travel: 800 mm Control: Heidenhain type: TNC 426 table surface area: 1250x630 mm workpiece weight: 1000 kg Tool changer: 24 spindle taper ISO: 40 turning speeds: 30-8000 U/min total power requirement: kW weight of the machine ca.: 7,5 t dimensions of the machine ca.: 4,2x3,3x3,15 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.