used LANDIS for sale

We offer Screw compressor Kaeser CS 121 75 kW-12 bar built in 1995 & separate air intake duct from outside and inside with flap control Picture 1-11 The system is part of a compressed air system in a production hall. It is used, built in 1995, and fully functional, in good condition and is offered by our customer due to the restructuring of the use of the hall. The display will be updated even further specifications: - Manufacturer: Kaeser Coburg - Model: Screw compressor Kaeser CS 121 with air intake duct from the outside and inside with flap control - LANDIS & GYR SQR 65.1 actuator for air flaps - Year of construction: verm 1995 - Machine No.: 1210382 - Operating hours: - electric 37756 / Compr. 20546 - Permissible operating pressure: 12 bar - Operating temperature: 75-85°C Engine - Nominal power: 75 kW - Engine speed: 1500 1/min - Degree of protection: IP ...

We offer Kaeser compressed air system consisting Schraubenkompressor.SC 1211, dryer DC 75E, compressed air tank 3000 l, piping with ultrafilter SG 0192, Sigma compressed air management system, Kaeser oil-water separation system and control cabinet The compressed air system is used to supply compressed air to a production hall. It was built or extended from 1995 - 2016 and is fully functional, in good condition and is offered for sale by our customer due to the restructuring of the hall use. The system must be serviced and inspected before it can be put back into operation. The system consists of the following components: 1. Screw compressor Kaeser CS 121 75 kW-12 bar built in 1995 & separate air intake duct from outside and inside with flap control 2, Adsorption dryer 1 Kaeser DC 75 E YOC 2016 6-16 bar 3. Compressed air tank flamco STAG 3000 l 16 bar Year 1995 704 kg 4 ...

Qty. 1 Second-hand Sendzimir reversing cold rolling mill Mfc.: Waterbury Farrel Type: WZS- Reversing - Sendzimir Rolling Mill type: ZR – 23M – 31”, reversing Z”, 1 – 2 – 3 – 4 Built: 1977 Modernised in 1991 Capacity: approx. 50 000 T/annum Strip width: 370 – 740 mm Strip tension: controlled up to 10 Tons Thickness: Entry: 3.5 mm Exit: 0.20 mm Speed: 183 – 368 m/min. Min. exit thickness of material M70-A: 0.04 mm Last pass from 0.12 to 0.04 mm Qty. 1 Second-hand roll grinder Mfc.: Landis Type: L-28A Roll dia.: 40-100 mm Roll length: up to 1500 mm Qty. 15 Containers

electric actuator LANDIS & STAEFA, SIEMENS SKD62 actuating force: 1.0 kN travel range: max. 20 mm Flange inner diameter: 45 mm motor: 17 VA 24 V AC 50 / 60 Hz New Dimensions: 170 x 130 x 300 mm

Three-phase meter LANDIS & GYR form ML262 3x 230 / 400 V 10 (60) A 50 Hz 1 kWh = 187.5 armature revolutions cable cover defective used, checked ! Dimensions: 320 x 180 x 135 mm

Description: Cogeneration plant for the electricity production from renewable sources The machine was created to be fueled with vegetable oils of rapeseed, sunflower and soybean oil, but thanks to the complex heated introduction system, it can burn animal fats and palm oil. The hourly production of electricity is equal to 940 kw/h The machinery is composed of: power source ,with fuel heating before combustion (underground tanks excluded) WÄRTSILÄ NSD 6R22/26 engine, produced in 1999 with a power of 1,065 kw at 1,000 rpm (power reduced to 940 kw/h to comply with authorisations) alternator DENOX system control panel catalytic silencer with cover and chimney chiller for cooling and heating systems hot water generation system with heat exchanger for powering warehouse heating systems transformer room ,with control panels, Landis+Gyr E650 meter, MESSINA SVT/R+AC/R medium  ...

Flow monitor, flow sensor -Manufacturer: Landis & Staefa, flow monitor type QVE81.13 unused original packaging -Techn. Data: see photo type plate -Dimensions cardboard: 305/135/H90 mm -Weight: 0.9 kg

Temperature controller, temperature sensor, setting for temperature, signal converter, temperature converter, temperature limiter -Manufacturer: Landis & Staefa -Type: RAM142.0/1982 -Dimensions: 185/95/H80 mm -Weight: 0.3 kg

High-frequency ignition device, heater, gas and oil burners -Landis & Gyr Type: LGK16.322A27 -Voltage: 220-240 V -Frequency: 50-60 Hz -Dimensions: 100/100/H125 mm -Weight: 1.2 kg

High-frequency ignition device, heater, gas and oil burners -Landis & Gyr Type: LFL1.622 -Voltage: 220-240V -Frequency: 50-60 Hz -Price: per piece -Number: 2 pieces -Dimensions: 100/100/H125 mm -Weight: 1.2 kg

High-frequency ignition device, heater, gas and oil burners -Landis & Gyr Type: LGK16.335A27 -Voltage: 220-240 V -Frequency: 50-60 Hz -Dimensions: 100/100/H125 mm -Weight: 1.1 kg

High-frequency ignition device, heating, gas and oil burners, automatic burner control, gas relay, Control box, burner control -Manufacturer: Landis & Staefa, automatic burner control unit -Type: LMG22.130A27 -Dimensions: 90/60/H60 mm -Weight: 0.2 kg

Electromechanical actuator for valves, valve drive, actuator, servomotor, air flap servomotor, air flap servomotor, gas pressure regulator, valve actuator -Manufacturer: Siemens/Landis & Gyr, electrohydraulic drive unused OVP -Type: SKP20.110B27 -Voltage: 220-240 V -Number: 2x drive available -Price: per piece -Dimension box: 250/150/H110 mm -Weight: 1.8 kg/Stück

Electromechanical actuator for valves, valve drive, actuator, servomotor, air flap servomotor, air flap servomotor, gas pressure regulator, valve actuator -Manufacturer: Siemens/Landis & Gyr, electrohydraulic drive unused OVP -Type: SKL90.110C27 -Voltage: 220-240 V -Number: 3x drive available -Price: per piece -Dimension box: 250/150/H110 mm -Weight: 1.8 kg/piece

Electromechanical actuator for valves, valve drive, actuator, servomotor, air damper actuator -Manufacturer: Siemens/Landis & Staefa, air damper actuator -Type: SQN75.6K4A11 -Voltage: 110 V -Number: 2 pieces available -Price: per piece -Dimension box: 155/110/70 mm -Weight: 0.4 kg/piece

Process controller, controller, temperature controller, temperature sensor, setting for temperature -Type: Sigmagyr RVP210.1 -Weight: 0.8 kg

Indoor device, High: 1800 mm, Long: 1500 mm, Width: 2450 mm, Weight: 4.000 kg, Ø tool: 300 mm, Total power: 7kW, Height of points: 150 mm, Distance between points: 600 mm, Width of the grinding wheel: 40 mm, Specification: universal