used WMW NILES for sale

Parallel Lathe WMW NILES type DLZ 500 IV L 1000 Between points: 1000 mm Maxi Ø on bench: 500 mm Maxi Ø over saddle: 300 mm Spindle diameter: Ø 50 mm Spindle speed: from 28 to 1400 RPM 3-jaws chuck Ø 200 mm Threadings: Metric + Whitworth Tailstock CM4 Auto Feeds transverse + longitudinal + rapid Lubricant pump Voltage: 380 V Dimensions (L x W x H): 3000 x 1400 x 1500 mm Weight: approx 2,5 T

Face plate diameter: 1.250mm Center height above foundation slab: 1,250mm Weight: 19t Power: 55Kw Max. torque on the face plate: 31,500Nm Maximum workpiece mass between centres: 16,000 kg Speed range: 2.24 – 224 rpm

Code 151295 Description Facinglathe with center Make WMW NILES Model DP 1 / S 2 Serial number 261 526 149 Year of make 1986 Max. centerheight over base plate 1250 mm Max. swing over base plate 2480 mm Max. swing in Gap 3100 mm Distance between centers 4000 mm Max. workpiece weight betw. centers 10.000 kgs Spindle bore 100 mm Movement slide ( max. ) 1000 ( + 750 ) mm crossslide 630 mm toolslide 200 mm 18 Speeds 5,6 – 280 rpm Motorpower 45 kW Total power 55 kVA Machine weight total ± 18000 kgs Accessoiries 4 chuck facingplate of Ø 1250 mm Condition Machine is in very good condition

Tip height: 1250 mm Turning diameter: 2,500 mm over bed Centre distance: 4.000 mm Support motion: 750 mm longitudinal feeds 630 mm cross feeds Face plate: Ã? 1250 mm Spindle speed: 5.6-280 RPM. Spindle bore: 100 mm Workpiece weight: 10.000 kg Equipped with: -Floor plates 4.500 x 2.200 mm -Powered tailstock -Operating instructions Country of origin: Germany Engine power: 45 kW Machine weight: 18,000 kg Machine Lxwxh: 8,000 x 4,000 x 2,100 mm

centre distance: 5000 mm turning diameter over bed: 4000 mm turning dia. in gap: 5000 mm spindle bore: 104 mm turning speeds: 1,4 - 71 (18x) U/min total power requirement: 30 kW weight of the machine ca.: t dimensions of the machine ca.: m 4-jaw face plate Ø 3.150 mm modular lathe! The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. width of grinding wheel: 50 mm ratio: 0 max. dia. of grinding wheel: 400 mm total power requirement: 3 kW weight of the machine ca.: 1000 kg dimensions of the machine ca.: m Pre-Dressing Device for Gear Grinding Wheels The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

3-jaw chuck, three-jaw chuck WMW DH-B 200x3x6 ( DH-B200x3x6 ) TGL 30-2332 Outer Ø: 200 mm bolt circle Ø : 133.5 mm bore Ø: 54 mm height with jaws: 140 mm used, tested ! Dimensions: 200 x 200 x 121 mm

Control Unit, Control Electronics, Numerical Control WMW, NILES TDR 100-01 ( TDR100-01 ) Input: 380 V AC 35 A 49 - 62 Hz Output: 270 V DC 25 A IP 00 New ! Dimensions: 250 x 160 x 160 mm

Control Unit, Control Electronics, Numerical Control WMW, NILES TDR 700-223 ( TDR700-223 ) Input: 380 V 3AC 41 A 49 - 62 Hz Output: 400 V DC 50 A Ersatzteil u.Ersatzteil u.a. for milling machine AUERBACH FkrSRS 250 CNC-H 646 ! used, tested ! Dimensions: 315 x 270 x 200 mm

3-jaw chuck, three-jaw chuck, lathe chuck WMW NILES outer Ø: 250 mm bore Ø:80 bolt circle: 180 mm flange: 220 mm height with jaws: 110 mm 2400 rpm with cross cone and camlock D1- 8 inch (stud M 16) 2 set of jaws (1x drill 1x rotary jaw set) 1 chuck wrench Dimensions: 250 x 250 x 195 mm

Control unit, control electronics, numerical control WMW, NILES 70.1011 1x PCB: 70.1011-13:1B/1 1x PCB: 70.1011-9:1B/1 1x PCB: 70.1011-11:1B/1 used, spare parts dispenser ! Dimensions: 250 x 160 x 160 mm

3- Jaw chuck WMW NILES DHK 200x3 Outer Ø: 200 mm Flange: 155 mm Bore Ø: 60 mm bolt circle: 175 mm Height with jaws: 125 mm feed number: 507 Dimensions: 200 x 200 x 125 mm

3-jaw chuck, three-jaw chuck, lathe chuck WMW NILES DH-B 315 x 3 x 6 outer Ø: 315 mm Bore Ø: 100 mm Height with jaws: 130 mm bolt circle: 33 / 290 mounting: M14 3 jaws extra Speed max.: 1800 rpm min. 20-240 mm max. 75-240 mm complete with inner and outer jaws Dimensions: 315 x 315 x 150 mm

turning diameter:480 mm turning length:1250 mm control:H 645 weight of the machine ca.:8 t dimensions of the machine ca.:5 x 2 x 2 m centre distance:1580 mm swing over bed:495 mm swing diameter:üb.Querschlitten ca.350 mm working area:1600 mm control:H645 connected load:50 kW

diameter:315 mm Speed:max. 2400 min. -1 weight of the machine ca.:25 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -DH B200x3x6 -TGL 30-2332 -Chuck size: Ø 200 mm -Cone: Ø 106 mm -Hole circle: Ø 135 mm -Through hole: Ø 54 mm -Weight: 15 kg

Two-jaw chuck, 2 jaw chucks, vice, face plate -Chuck size: Ø 200 mm -centrically exciting: -Passage: Ø 54 mm -Weight: 15 kg

Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 315 mm -Passage: Ø 104 mm -Weight: 44 kg

Wedge rod feed, swivel feed, swivel swivel feed, power clamp feed -Feed size: Ø 250 mm -Weight: 35.5 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Fucking size: Ø 200 m -Through hole: Ø 54 mm -Weight: 12 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 160 mm -TGL: 30-2312 -Weight: 11.2 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 250 mm -Rezess: Ø 210 mm -Throughout: Ø 80 mm -Weight: 20.7 kg

Wedge bar chucks, three-jaw chucks, three-jaw lathe chucks, power chucks -Chuck size: Ø 250 mm -Short taper: 8 -Thread: M30 -Pitch: 1.5 mm -Weight: 38.5 kg

Three-jaw chuck, three-jaw lathe chuck, 3-jaw chuck -Chuck size O 200 mm -Through hole O 54 mm -Short cone 6 -according to pictures, without additional accessories -Weight 14.4kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -DH: 200x3-III -TGL: 30-2332 -Chuck size: Ø 200 mm -Weight: 16.7 kg

Precision three-jaw chuck, chuck, face plate, 3-jaw chuck -DHK: 200x3 -TGL: 30-2333 -Chuck size: Ø 200 mm -Beeks: individually and completely adjustable -interchangeable jaws -Through hole: 55 mm -Rezess: Ø 160 mm -Number: 1x feed available -Price: per piece -Weight: 16 kg

Three-jaw chuck, three-jaw lathe chuck -Type: DH315x4-III/TGL 30-2332 -Chuck size: Ø 315 mm -Passage: Ø 98 mm -Rezess: Ø 264 mm -Weight: 32 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 250 mm -Short taper: 6 -Throughout: Ø 80 mm -Weight: 25.9 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -DH: B200x3x6 -TGL: 30-2332 -Chuck size: Ø 200 mm -Cone: Ø 104 mm -Hole circle: Ø 132 mm -Through hole: Ø 54 mm -Weight: 15 kg

Three-jaw chuck, three-jaw lathe chuck -DH200x3-III -TGL: 30-2332 -Chuck size: Ø 200 mm -Rezess: Ø 155 mm -Hole circle: Ø 174 mm -Through hole: Ø 57 mm -Weight: 12 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Fucking size: Ø 200 m -Through hole: Ø 54 mm -Short taper: 5 -Hole circle: 105 mm -Weight: 16.2 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 200 mm -Thread recording -Through hole: Ø 53 mm -Weight: 19.7 kg

Three-jaw chuck, three-jaw lathe chuck -Manufacturer: Rohm, three-jaw chuck Chuck size: Ø 250 mm -Type: DH-B / 8-250 x 3 TGL 30-2332 -Throughout: Ø 40 mm - Hole circle: Ø 171 mm -Shot: short taper 8 -Weight: 24 kg

Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 250 mm -one set: hard interchangeable jaws -Passage: 81 mm -Rezess: Ø 210 mm -Hole circle: Ø 230 mm -Weight: 19 kg

Four-jaw chuck, four-jaw lathe chuck, 4 jaw chuck -Type: DH250x4/TGL30-2332 -Chuck size: Ø 250 mm -Throughout: Ø 80 mm -Rezess: Ø 210 mm -Hole circle: Ø 230 mm -Number: 3x available -Price: per piece -Weight: 18 kg

Swivel lining, 3- cheek lining -Type: DHB 200x3x5 TGL 30 2332 -Feed size: Ø 200 mm -Passage: Ø 54 mm -max.: 3000 Rpm -Short cone recording: Ø 105 mm -Weight: 24 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 250 mm -Cone: Ø 139 mm -Hole circle: Ø 170 mm -Through hole: Ø 80 mm -Weight: 24 kg

Precision four-jaw chuck, chuck, face plate, 4-jaw chuck -Manufacturer: WMW Niles, four-jaw chuck type DHK-B/8-250x4 -Chuck size: O 250 mm -Passage: O 80 mm -Bolt circle: O 135 mm -Intake: short taper 6 -Weight: 35kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 200 mm -Short taper mount for: bayonet mount -Cone size: 6 -Cone: Ø 106 mm -Hole circle: Ø 133.4 mm -Through hole: Ø 54 mm -Weight: 15 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 160 mm -DKRD Ø: 160 mm -Weight: 15.5 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -DH250x3-III -TGL 30-2332 -Chuck size: Ø 250 mm -Cone: Ø 140 mm -Hole circle: Ø 172 mm -Through hole: Ø 80 mm -Weight: 28 kg

Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 200 mm -Weight: 18 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 250 mm -recess recess: Ø 210 mm -Through hole: Ø 80 mm -Weight: 18 kg