Model
(Manufacturer: WMW)
max. load: - kg : - weight: - kg 10 off used machine shoes. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
tool taper: MK4 diameter of tools max.: Ø 145 mm table-size: L: 800 x B: 700 mm surface area: Ø 300 mm table travel: 200 mm total power requirement: 7,5 kW weight of the machine ca.: 4,9 t dimensions of the machine ca.: 2,8 x 1,5 x 2,3 m Additional information: Application: Gear hobbing machine for gear cutting of spur and helical gears, worm gears and rollable profiles Cycle milling and single milling as well as up-cut and climb milling Specifications for machining spur and worm gears: -Outer Ø max. 250mm with counterholder -pitch max. 5mm -Tooth helix max. 45° -Tooth width max. axial milling 200mm and radial-axial milling 240mm -Milling width max. clamping table counterholder 655mm Milling slide: -swivelling 210° -travelling distance 350mm -feed, 2 directions, 16 steps in the range 0.2 - 6.3 mm/revolution Further features: -counter-point taper MK4, co-rotating -Centre distance of ...
diameter: 200 mm amount: 6 STK The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 700 mm table width: 700 mm table height: 630 mm power capacity: kW weight of the machine ca.: 0,65 t dimensions of the machine ca.: 0,9 x 0,8 x 0,7 m partial adjustable cube table - 30° in mint condition, The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 63 t distance between columns: 320 mm stroke: 8 - 120 mm table-size: 800 x 600 mm ram surface: 500 x 400 mm throat: 315 mm dayligth: 410 mm ram adjustment: 70 mm no. of strokes: 56 / 90 Hub/min total power requirement: 6 kW weight of the machine ca.: 5,5 t dimensions: 2,10 x 1,52 x 2,72 m inclinable The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: für Stangen und ... : für dickwandige Rohre working area: 30 - 80 mm Ø main drive: 38 kW : Ein- und Auslauf total wight: 12 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
stroke adjustable from - to: 0 - 150 mm faceplate diameter: 300 mm taper MK: für MK6 weight of the machine ca.: 0,05 t : The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
frequency: 50 Hz voltage: 380 V : 220 V connected load: 2,6 kVA rated current: 6,1 A weight of the machine ca.: 1 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Table diameter: 2000 mm Turning diameter: 1800 mm Turning height: 1250 mm Motor power: 35 HP/kW Positions ATC: 0 Positions APC: 0 MACH-id 4306 MAKE WMW TYPE DKZ 2000 x 1250 B YEAR 1976 SPECIFICATIONS Max. turning diamter Ø 2000 mm Table / chuck size Ø 1800 mm Workpiece height 1250 mm Work piece weight 6000 Kg Horizontal movement support / ram 1150 mm Stroke support left ram 700 mm Stroke support right ram 700 mm Angle adjustment / ram swivable 30 Spindle speeds / ranges 50 Rpm Power 35 Kw DIMENSIONS Length 4100 mm Width 5300 mm Heig ...
Grinding diameter: 630 mm Grinding length: 4000 mm Workpiece weight: 900 kg CNC Brand: Siemens CNC Model: SIEMENS 840D 4 Axis controlled X, U, Z and C Axis Large steady rest package 6 units Concave grinding Covex grinding Dressing system Rebuild by Primoteq Centre height: 315mm Grinding Ø: 630mm Grinding length: 4000mm Grinding stone dimensions:710 x 80 x 305mm Table inclasement: -5 to + 5° Tailstock: 6Mk Coolant system: Yes Filtration: Yes Length: 12000mm Width: &nb ...
Spindle diameter: 0 mm Longitudinal X: 9000 mm Vertical Y: 4000 mm Cross Z: 1000 mm Positions ATC: 80 Table length: 2500 mm Table width: 2500 mm Number of tables: 1 CNC Brand: Heidenhain CNC Model: TNC 430 WMW - BP 160 CNC Floor type Horizontal borer Ø 160 with Y 4000 mm MACH - ID 6368 Make: WMW Type: BP 160 Control: HeidenHain TNC 430 YOP: 2001 X – Travel 9.000 mm Y – Travel 4.000 mm Z – Travel 1.000 mm W – Travel 800 mm Table Length 2.500 mm Table Width 2.500 mm Table load 30.000 kg Speeds / ranges 2000 Rpm Power 52 kW Ram size 500 x 620 mm Spindle Taper Iso 50 IS ...
Grinding diameter: 315mm, grinding length: 2500mm, center height: 165mm, speed: 500rpm (10 steps), spindle bore diameter/taper: 30mm/MK4, grinding wheel diameter: max. 500mm, table size: 3500mm/310mm, table tilt: approx. 4.8°, longitudinal feed of the table: 5-2680mm, feed: 50-4000mm/rev. Weight: approx. 7400kg, Dimensions X/Y/Z: 6500mm/1700mm/2000mm. Headstock defective, can be repaired.
Projection: 315mm, spindle speeds min.-max.: 9 steps, 63rpm-1000rpm, worktable size: 500mm/400mm, dimensions X/Y/Z: 2300mm/1000mm/700mm, weight: 1000kg. Feed defective.
UBBDA Three Roll Plate Bending Machine The three-roll sheet bending machine is designed for the production of cylindrical and conical sheet shells. Electric motors 42 kW, 580 rpm, 750\1500 rpm Dimensions 12900x5300x5620 Gross weight 166260 t
WMW Heckert 6000 x 1050 mm Cylinder Grinding Machine Table size : 1050X6000 Machine is in very good condition
Clamping angle WMW Clamping area: 200 x 194 x 44 mm Bridge width: 50 / 62 / 46 mm Groove width: 18 / 30 mm Groove depth: 30 mm Mounting area: 200 x 150 x 24 mm used, tested ! Dimensions: 200 x 150 x 194 mm
Clamping table, clamping plate, milling table, machine table WMW Clamping area: 425 x 165 mm Panel thickness: 60 mm Groove width: 12 / 20 mm groove depth: 20 mm web width: 19 / 45 / 45 / 19 mm guide groove: width: 12 mm, depth: 5 mm ( on top and bottom ) hole spacing ( fastening screws ): 365 x 60 mm 4x bore: Ø 14 / 20 mm used, tested ! Dimensions: 425 x 165 x 60 mm
Cutter mandrels, tool holder, with tightening thread WMW, VWF 40 x 22 x 315 ( 40x22x315 ) SK40 tool holder: Ø 22 x 315 mm used ! Dimensions: 468 x 63 x 63 mm
Pneumatic Grinder, Pneumatic Straight Grinder WMW Type 1804 17000 rpm Grinding wheel diameter: Ø 50 mm with approx. 1.6 m Connection hose used, tested ! Dimensions: 330 x 50 x 80 mm
Clamping drive, clamping force generator, electric WMW EDU I80 DR speed: 80 rpm torque ( adjustable in 8 steps ): 20 - 120 Nm engine: KMRB 71 K 4 E 0,55 kW 1380 rpm 220 / 380 V 3AC hollow shaft: Wedge hub profile 4 x 18 x 22 x 6 ( TGL 0-5471 ) bolt circle diameter: Ø 90 mm, 4x threaded hole M8 x 1.25 used, tested ! Dimensions: 280 x 130 x 170 mm
Milling head, drill head, angle head WMW Tool holder: SK40 with collet chuck size 25 360 ° rotatable in two planes shaft ( Drive , machine side ): SK50 shaft ( drive, milling head side ): Wedge hub profile 8 x 36 x 42 x 8 ( TGL 0-5472 ) flange: Ø 260 mm / 397 x 339 mm hole spacing: 365 / 175 mm 4x Bore: Ø 19 mm used, tested ! Dimensions: 400 x 390 x 600 mm
Clamping actuator, clamping force generator, electric, with reversing switch WMW EDU I80 F/M1 speed: 80 rpm torque ( adjustable in 8 steps ): 20 - 120 Nm engine: KMRB 71 G 4 E 0,75 kW 1380 RPM 220 / 380 V 3AC Hollow Shaft: Wedge hub profile 4 x 18 x 22 x 6 ( TGL 0-5471 ) Bolt circle diameter: Ø 90 mm, 4x threaded hole M8 x 1.25 used, tested ! dimensions: 280 x 130 x 190 mm
Clamping actuator, clamping force generator, electric WMW EDU I160 Bj: 1979 torque adjustable in 8 steps max. 110 Nm 160 rpm 220 / 380 V 3AC 0,75 kW spline shaft profile according to TGL 0-5471 for more clamping actuators see MMZ158, MMZ159 !; New ! Dimensions: 280 x 130 x 170 mm
Machine vice WMW SX/1-160 TGL 34180 jaw width: 160 mm jaw height: 48 mm wingspan: 0...200 mm New ! dimensions ( machine vice ): 505 x 160 x 135 mm
Centering vice, machine vice WMW SZ 160 jaw width: 160 mm jaw height: 48 mm wingspan: 0...200 mm used, tested ! Dimensions ( machine vice ): 505 x 160 x 117 mm
diameter range 3-10 mm cutting length 2000 mm speed - meters/min 22-71