Fabricante:
(Categoría: 302)
Compounding system with underwater granulation. Material: PE, PP, PS, ABS (+ fillers) // Details: DC motor, DC rotor, segmented screws (2x x 70 mm / 40D) and cylinders, degassing, vacuum pump, stuffing unit, backwash screen changer GNEUSS RSF 150, underwater granulation GALA with cutting rotor, water circulation system, heat exchanger, centrifugal dryer. Controls: SIEMENS S7 with screen visualization. Available at an additional cost: Sidefeeder, 4-fold gravimetric dosing system. (Ref. No. G27615.2)
EREMA Series Type 1109 TVEplus ecoSAVE for processing polyethylene (PE), polypropylene (PP) and polystyrene (PS), with screen changer, degassing for processing printed films. Output up to 450 kg/h, electrics 460 volts, 60 hertz (US standard), available immediately. Auch + Technik e. Kfm. D-73728 Esslingen Phone +49 1577 5329827
Mikrosan Twin Screw Extruder Screw diameter : 67 mm Parallel screw ... más información
BARMAG AIR TEXTURIZING LINES for the production of artificial grass yarn, The supply can be split as follows:, - Texturizing machine, - Barmag twister, - SIMA Winder, - Roblon T5000, - SIMA T2TR, - Fare Extruder, - Meromat rope machine, These machines are used to texturize synthetic grass., less than 500 worked hours, as new, texturizers available, each one consists of:, monofilament texturizing unit for one yarn, with 2 electrically heated godets, each one with separating roller, diameter: 132mm - length: 150mm, 1 heating zone per godet, godet temperature: maximum 180 °c, temperature tolerance on godet surface: +/- 2 °c, temperature tolerance between godets: +/- 1.5 °c, separating rollers with ball bearings, with 1 piece texturing jet, for texturizing of various yarns, heater for compressed air with automatic temperature and pressure control, cooling drum with blower and air filter, ...
CAST FILM EXTRUSION LINE SML winding unit This production line was professionally dismantled in 2017 Designed for COEX- cast foil production. Processing of thermo plastics in a temperature range of 150-300°C. The system can be operated with the following combinations: - Main unit (CoEx system) from Kuhne POSSIBLE LAYER STRUCTURES: - monofilm - 3-layer film (A-B-A) MAIN EXTRUSION SYSTEM FROM KUHNE Total system output max. 900 kg / h Main extruder: 105/33 L / D max. 650kg / h Extruder CO .: 90/33 L / D max. 250kg / h Foil width NET: 800-1400 mm Thickness: 25-530 µm Production speed 8-150m/min Roller width: 1600 mm Max. Roll weight: 2000 kg Version with Airnife and vacuum box One gravimetric dosing device with 3 stations per extruder Each extruder is equipped with a melt pump and a 2-piston screen changer ADDITIONAL COMPONENTS (QUALITY): Non-cont ...
YEAR 2010 1. TAI-1300C - LIFTING UNWINDER Product Width: 100-1250mm Diameter of roll max 1000mm Edge Position Control System (E.P.C) Auto Tension Control System 2. TA-1300DTC-2 - DRAW-TAPE FEEDING SYSTEM Tape Thickness: 0.015-0.02mm (HDPE) Draw-Tape Width: 80-100mm Max. O. D. of Draw-Tape: 650mm 3. TA-S-1250 - SHUTTLE TRACK SEALING & PERFORATING UNIT Max. Bag Length: 1200mm (Max. Sealing Width) Bag Width: 140-2000mm Film Thickness: 0.01-0.08mm (LLDPE, Single Layer) 0.008-0.025mm (HDPE, Single Layer) Speed 100 m/min 4. TAF-1700 - TRIANGLE FOLDING UNIT 5. TAD-450 - FOUR SHAFT SPINDLING WINDER Coreless Production Width: 100-380 mm One of the Machines is upgraded to new model Servo driven punching device and hot air sealing system for draw tape sealing unit.
Material: PE, PP, PS, ABS / Details: DC motor 220 kW, degassing, dcrunner, screw diameter 70 mm, LD: 32, Throughput: approx. 400 - 600 KG/hr. ... más información
For Sale: Jwell 65-132 Extrusion - Twin Screw Extruder Manufacturer: Jwell Model: 65-132 Year of Manufacture: 2010 Technical Condition: Excellent Screw Diameter: 65.0 mm Usage Duration: 6 months This Jwell 65-132 Twin Screw Extruder is in very good condition, having been used for only 6 months. It is an ideal choice for those seeking reliable and efficient extrusion solutions.
China Q1500 extrusion line I sell a line for the production of double layer babel film 1500 cm I offer a 100% working, currently operating line for the production of two-layer film 1500cm. line is currently working, is fully operational, the line of 2010, including estruder, winder, chiller, control cabinet, full operating instructions
Complete regranulation plant OMP Prealpina Type:ES-130. Screw and cylinder were renewed in November 2021 A new groove bushing as a spare part Simple degassing with vacuum pump DC drive used for PE/PP. Throughput at PE approx. 500-600kg. at PP.450-500.kg. per.h. Consisting of foil silo with agitator and discharge screw. Regrind/granulate dosing screw. Masterbatch dosing screw Tamping plant Extruder 130 L/D Hot tee granulator( also water ring granulator) Centrifuge Classifying sieve Removal with pressure blower. Plant is tested and stored (immediately ready for use)
According to description pdf attached complete line for profiles + WPC profiles ... más información
Extrusion line for the production of heat-shrinkable OPS (oriented polystyrene) film Product structure A/B/A Recyclable materials (mixed) SBC, GPPS Thickness 40-60 microns % shrinkage 70-72% Net width / when leaving TDO 2780 / 3200 Main extruder ZSK Mc70 plus Coextruder 50 mm Static mixers - in the main extruder and co-extruder lines. Die - Nordson Autoflex VI-R H40 Die 750 mm (28 bolts) Roll stack - 2 shafts (with mirror surface - chrome) MDO 6 shafts (1, 2 - preheating; 3-4 stretching 1:1.2; 5.6 - annealing) 2 thickness measurement sensors from NDC (USA, UK) with automatic thickness control, new control equipment installed in 2018. (computer and software), sensors - overhaul in the UK from the manufacturer (NDC) - 2019-2020 TDO stretch up to 1:5 Filmatic winder from W&H (Germany), Max. roll diameter 580mm, expandable to 800mm line speed (mechanical) up to 50 m/min Volt ...
The extrusion line was designed for cast film production. Processing of thermo plastics in a temperature range of 150-300°C. POSSIBLE LAYER STRUCTURES: - mono film - 3- layer (A-B+C-A) - 5- layer (A-B-C-B-A) DATA OF FACILITY Total output of extruders max. 2230 kg/h Extruder A: 90/33 L/D max. 330 kg/h Extruder B.: 135/33 L/D max. 950 kg/h Extruder C.: 135/33 L/D max. 950 kg/h Film width range (net): 1600 - 2110 mm Two rolls cutting possible (2x 800 – 2x 1055mm) Thickness range: 25-580μm Production speed: 10 - 150m/min Roll width: 2500 mm Max. roll weight: 2000kg ADDITIONAL COMPONENTS (QUALITY): Non-contact thickness equipment for automatic TD profile measurement with double side corona treatment (max. 12000W) Optical inspection system, including marker system if failures are detected, incident and transmitted light system ...
The extrusion line is a COEX cast film line. Processing of thermoplastics in a processing range of 150-300°C. Possible layer structures: - Monofilms - 3- layer (A-B+C-A) - 5- layer (A-B-C-B-A) Plant data: Total system output max. 2230 kg/h Extruder A: 90/33 L/D max. 330kg/h Extruder B.: 135/33 L/D max. 950kg/h Extruder C.: 135/33 L/D max. 950kg/h Film width NET: 1600 - 2110mm; Center cut for 2 bobsleighs possible (2x 800 – 2x 1055mm) Thickness: 25-580μm Production speed 10 - 150m/min Roll width 2500 mm roll weight 2000kg Additional components (quality): non-contact thickness gauge for automatic nozzle with automatic cross profile control on both sides Corona pretreatment (max. 12000W) Optical surface inspection system incl. defect marking in open and pass-through light Ancillary equipment: Dryer 1 – 4 with 4500 liters volume ; Heating capacity 48kw dryer 5 ...
manufactured in China with german overhead and according to europ. Standards ... más información
Used twin-screw, parallel, counter-rotating extruder by Amut model BA92 NOMAX. New 2011. Output: 270 - 370 kg/h Hours of operation: 53638 h Other details: - Diameter of augers 92 mm - L/D ratio 28:1 - Drive power 60 kW (400V, 50 Hz, 3 ph) AC - Two sets of screws -for ABS processing -for PVC processing - Number of cylinder heating zones 7 - Number of cylinder cooling zones (air) 4 - Number of heating zones for head and adaptor 5 + 1 - Built-in pressure and temperature measurement system for plastic mass - Thermal oil unit for thermostating the worms for PVC - Drive power of vacuum degassing pump 11 kW - Drive power of screw feeder 1.5 kW - Without control (subassemblies available according to the list)
PE 300 plastic recycling and regranulation line was built in China in 2011 by Zhangjiagang Wuhe Machinery Co. LTD. The extruder for plastics used in the processing and manufacturing of various types of materials can produce up to 300 kg of parts in one hour of operation. The complete PE and PP plastic extrusion line includes a compactor, screw, cylinder, conveying system, heating system and temperature control panel. Material production begins by heating the plastic to a maximum temperature of 300°C in the 11 heating zones of the PE 300 granulating line, controlled by thermoregulators. The extruder then presses the material further through a 100 mm diameter screw located in a cylinder with abrasion and rust protection. At the end of the process, the machine head moulds the plastic to give it the right properties and shape. The PE 300 extruder is equipped with thermoregulators with ...