Fabricante:
(Categoría: 202)
Specifications / Technical Data S-720/T CNC-Engraving-Machine / Milling machine / CNC-Router With the purchase of the T-variation of High-Z CNC-router you get a proven technology with a certain icing of the cake in TÜV-certified quality. High-Z/T 3D-cnc-engraver was conceived for once more precision (repetition precision approx. 0,02mm) and especially for higher traverse speed. Because of the used ball screws the High-Z/T cnc milling machines achieves a fantastic precision and an almost unmeasurable back lash of approx. 0,01mm. At the same time there are high traverse speeds up to approx. 108mm / sec. ( 6.500 mm/min ) possible. With this cnc-machines you're able to carry out an engrave and mill speeds of approx. 4500 mm/min. and express travels up to 6500mm/min. Here's a video on a unloaded drive with the new High-Z / T. This cnc-machine series is usable in the industrial field a ...
Specifications / Technical Data S-400/T CNC portal fraesmachine / engraving machine, TUeV certified Already more than 4500 CNC machines of type High-Z sold worldwide ! With the T-variant of the High-Z CNC-Fraesmaschine you acquire old-fashioned technology with the certain I-T-Tpfelchen The High-Z/T is designed for even more accuracy (repeatability about 0.01mm ) and especially for higher travel speeds. The high-Z/T CNC fraes machine achieves fantastic accuracy and an almost unmeasurable reversal of about 0.01mm due to the ball-circuit spindles used. At the same time, high travel speeds of up to 108mm/second ( 6500mm/ minute) can be achieved. Thus, engraving and fraes speeds of up to approx. 4500mm/min can be realized and fast-moving speeds up to approx. 7000mm/min. This is just as applicable in the industrial sector for work such as engraving, frause, drilling, measuring, cutting, as wel ...
Specifications / Technical Data S-400/T CNC-Portal-Router / CNC-Engraving machine with TÜV certification With the purchase of the T-variation of High-Z cnc-router you get a proven technology with a certain icing of the cake in TÜV-certified quality. High-Z/T cnc-routers was conceived for once more precision (repetition precision approx. 0,02mm) and especially for higher traverse speed. Because of the used ball screws the High-Z/T 3D-cnc-engravers achieves a fantastic precision and an almost unmeasurable back lash of approx. 0,01mm. At the same time there are high traverse speeds up to approx. 108mm / sec. ( 6.500 mm/min ) possible. With this cnc-machines you're able to carry out an engrave and mill speeds of approx. 4500 mm/min. and express travels up to 6500mm/min. Here's a video on a unloaded drive with the new High-Z / T. This 3D-milling-machine series is usable in the indust ...
Important and outstanding design features of the RaptorX-SL with steel substructure / gantry design RaptorX-SL1200/S20 The range of applications of a RaptorX-SL CNC Fraesmaschine is variable due to the adjustable working area (through-lasshoehe under Bruecke: 150mm, 300mm or 400mm ) and the travel height of 300mm in the Z-axis (at no extra charge) extremely large. special size (on one piece) x 3000 mm x 600 mm are feasible ! If you are interested please ask ! To such a way that you are able to process plate materials with the greatest stability of the Z-axis exactly as accurately as 200mm high 3D-Koerper. Use the system as a plasma cutting system or water jet cutting system, are available In the middle range of the machine (between the foottubes) you can even process parts up to a height of 850mm (beam rail etc. ) or 3D body up to about 400mm height ( at 400mm long Fraeser ), whereby th ...
- German production - DTR, CE - year of manufacture 2010 - high efficiency up to 200 elements / min - 28 km / 8h TECHNICAL PARAMETERS: Wood parameters - width 60 - 225 mm - thickness 18 - 48 mm - length 300 - 2000 mm - pressing length 8100 - 16400 mm - power consumption 150 kW - air consumption 3100 Nl/min - suction capacity 14845 m3/h - two milling stations - undercutters - connecting to the line and zyzgka - loading with a conveyor with spacers - package width 600 mm - split ironing length Dimensions of the folding machine - length 42000 mm - width 6000 mm - height 2100 mm
Cone slot milling machine Duko L x W x H: 1300 x 1000 x 1500 mm Weight approx. 800 kg Built in 1963 The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Flush milling machine HolzHer UF 362 Year of construction 1975 L x W x H: 150 x 80 x 160 cm Weight approx. 440 kg The machine is in good condition, ready for operation, Changes, errors, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Phone 0041 62 966 18 32 fax 0041 62 966 21 12
Chain stemmer GF with drilling unit for wall mounting L x W x H: 1200 x 800 x 2300 mm Built in 1972 The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Edge flush milling machine JKO LT 750 with feed-in apparatus Masch. No. 1666 L x W x H: 1100 x 1000 x 1500 mm Built in 1966 Weight approx. 520 kg The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Tool to CNC milling center Steep cone-cone SK 40 Vsadrq with tightening bolt Tool according to the pictures flat rate EUR 6980.00 Built in 2003 In good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Edge Abkappen thrower HolzHer Built in 1978 Weight approx. 220 kg L x W x H: 80 x 60 x 150 cm The machine is in good condition, ready to use. Subject to changes, errors, and intermediate sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Gebr. Table milling machine with cross-cut saws STEHLE F3E Table size: 117 x 86.5 cm Table height: 85.5 cm Milling machine: Motor power: 4 kW 2 milling spindles: 30 + 40 mm Height adjustment via handwheel Height adjustment range of the milling spindle: 115 mm Left- and clockwise rotation 4 speeds: 3.0 / 5.0 / 6.0 / 10,000 rpm. Doubling the speed via selector switch Crosscut saws: Engine power: 3 hp (2.2 kW) max. saw blade diameter: 350 mm max. cutting height: 110 mm Lateral adjustment range: 120 mm Sliding carriage incl. slotted hood (self-made) Instruction manual available Transport dimensions (approx. dimensions): L: 205 cm W: 100 cm H: 120 cm approx. 1,000 kg Sold in ACTUAL condition and unrefurbished from carpentry dissolution. Fixed price.
Classifieds Home & Garden DIY Your Ad Visits: 17 Wishlist: 0 Ends on: 26.05.2024 Edit Reserve Lengthen Delete Print a sales sign Highlight Ad Duration Price Push up Get new attention! Your ad will look like a new ad. one-time 3,95 € Highlight: Up to 2x more visibility! Your ad will be highlighted in color. 7 days 4,95 € Up to 5x more visibility! Your ad will be pushed up every day for a week. 7 days € 16.95 Up to 10x more visibility! Your ad is at the top of the list! 7 days € 19.95 Gallery: Up to 15x more visibility! Your ad will appear on the home page! 10 days € 49.95 All prices incl. VAT. Swivel Spindle Milling Machine FELDER F38 Rotary Milling Machine Table Milling Machine Feed in Langenbach Swivel Spindle Milling Machine FELDER F38 Swivel Milling Machine Table Milling Machine Feed €5,652 Pick-up only ...
Gebr. Chain Clamp HARBS UKS YOC 1962 on base frame Transport height: 172 cm incl. various chains Sold in ACTUAL condition and unrefurbished from carpentry dissolution. Fixed price. ... más información
Gebr. Safety milling fence for bench milling machines Manufacturer presumably PANHANS with handwheel adjustment Digital displays via counter incl. pictured stop jaws Suction connection: 120 mm Distance between the two fastening screws: approx. 330 mm ex location ... más información
Copy lathe Manufacturer: Hempel Model: CKS-12 For the production of moulded turned parts in small series Without the use of moulded steels Scanning via sheet metal template or wooden model Turning length max.: 1200mm Rotary diameter max.: 250 mm Spindle motor: 5.5 KW Hydraulic motor: 2.2 KW
Model Author 503, 3 axis machine, x = 900 y = 2600 Z = 80, with groove saw, 1 x milling, T dowel drilling 18 + 3 on the front side, 2 + 2 from the back and front 1 x, year of manufacture 95 ... más información
Double spindle cutter, speeds 3000/4000/6000/8000/10000 rpm , Spindle stroke: 150 mm, spindle diameter 30 mm. Two pcs. Once of it with a feed. In the sales order. ... más información