rociadoras de cola usadas para la venta

Code: 0806 Brand: HIRZT - ITALY Model: B 300 - CE Standard Automatic edge bander for pre-glued edges in strips or rolls: melamine, plastic laminates, veneer, etc . up to 3 mm thickness - CE Standard Composition: Motor V. 220 single-phase Pneumatic end cutting unit (shear) front and rear Blower with air filter - Power 440 W Trimming copying unit with adjustment from the outside - Motors 220 x 2 W - Trimmer speed rpm 10000 End cutting finishing unit with foot control N° 20 rollers inclined on the plane Feed motor 13 wheels V.200 single-phase - Speed 4,7 mt/min Max edge thickness mm 3 Panel thickness min/max 10/50 mm Min panel dimensions mm 70 x 140 Total absorption Kw 3,8 Digital thermometer 10-350 degrees Extensible front support Overall dimensions mm 1800 x 700 x 1300 h Weight kg 250

Glue application machine with 2 rollers Mod. SC2R-1300 Year: 2006 Production: FIN s.r.l. Italy Main technical specification: Width of machining: 1300mm Maximum passage between rollers: 120 mm Diameter of rollers: 185mm Progress speed: 19m/min Net weight 390 kg Overall dimensions: 64 x 210 x 136cm Overall dimensions with case: 73 x 222 x 153cm 400 V, 50 Hz, 037 Kw Accurate and uniform application with any type of adhesive, excellent technical characteristics, For the high practicality, functionality and safety for the operator, set it at the at the top of the 2-roll glue application machines. Coating roller covered with acid-resistant rubber, ground and grooved, hard-wearing as they are Built with a rational layer of rubber, it is therefore possible to carry out 6-7 grinds. It is easy and quick to disassemble. Distribute, precisely and evenly on one or both sides ...

I am selling a fully equipped edge banding machine HOMAG EDGETEQ S-500 KAL370 Ambition 2484, built in 2019: Configuration: Input stop servo-motor adjustable Manually adjustable joint milling Edge banding with preheating tanks 2 pcs. Material pressure zone can be adjusted by servo motor Pneumatically adjustable cross-cut saws Heavy milling top + bottom pneumatically adjustable Round unit 4-motor servo motor adjustable R2 / second set R1 included Swivel groove saw unit Radius scraper blade Multiradius servo motor adjustable Scraper blade surface can be pneumatically adjusted Polishing brushes Separator injection at the front Clean injection at the rear Working height adjustable by servo motor Material height 8-60mm Edge material thickness 0.4-12 (20)mm Feed speed 16 to 25m/min. Overall length including feed plate 8365mm Mileage status 833,000 meters. Input appar ...

I am selling a fully equipped edge banding machine BRANDT ProfiLine KDF 790, built in 2006: Configuration: Input stop can be adjusted by menu Manually adjustable joint milling Edge banding with preheating tank Material pressure zone can be adjusted by servo motor Pneumatically adjustable cross-cut saws Heavy milling at the top + at the bottom manually adjustable Radius milling top + bottom servo motor adjustable Groove saw unit at the bottom Round unit 2-motor servo motor adjustable Radius scraper blade R2 pneumatically adjustable / second set R1 included Scraper blade surface Polishing brushes Separator injection at the front Clean injection at the rear Working height adjustable by servo motor Material height 6-60mm Edge material thickness 0.4-12mm Feed speed up to 20m/min. Overall length including feed plate 7860mm Mileage status 1,650,000 meters glued. Incl ...

I sell a fully equipped edge banding machine SCM Olimpic S3000, built in 2011: Configuration: Input stop servo motor adjustable Pneumatically adjustable joint milling machines Edge banding with preheating tank Material pressure zone servo motor adjustable Cross-cut saws pneumatically adjustable Strong milling machines can be adjusted manually Pneumatically adjustable radius milling top + bottom Round unit 4-motor pneumatically adjustable Radius puller blade R2 can be switched off pneumatically Surface of the drawing blade Polishing brushes Hot-air blower Separator injection front and rear STARTOUCH control system Control panel Barcode reader Working height servo motor adjustable Material height 6-60mm Edge material thickness 0.4-12mm Feed speed up to 12m/min. PUR glue possible. Second glue tank brand new included. Only 6,153 meters glued! Machine practically ...

I am selling an edge banding machine Holz-Her Sprint 1310, built in 2004. Configuration: Edge banding Cartridge glue Cross-cut saws Swivelling radius milling machines Radius pulling blade Polishing brushes Very good condition, fully operational.  ... más información

Gluing stand VHS with motor hydraulics for gluing all frame constructions with dowel connection – tine connection – 45° miter connection. The motor-hydraulic gluing stands VHS are available in the following sizes: Maximum grouting range 2,500 x 1,800 mm 2,500 x 2,100 mm 3,000 x 1,800 mm 3,000 x 2,100 mm 3,500 x 2,100 mm Three vertical press cylinders with a stroke range of 120 mm and a pressing force of 2 tons each. Two horizontal press cylinders with a stroke range of 120 mm and a pressing force of 2 tons each (optionally, the gluing stands can of course be supplied with more press cylinders). Drive power 0.75 to 1.25 kW.

SPECIFICATIONS: Dimensions of the working table mm: 640 x 900 Distance between dowel collectors mm: 19 06 Vibration outputs Düberl diameter mm: 10 - 12 02 Glue and water containers Voltage: 220 V Complete with: - Control cabinet with push-button strip - Control pedal -Protective devices

SPECIFICATIONS: Workpiece thickness max mm: 60 Edge material thickness mm: min 0.5 - max 3.0 Minimum radius border min mm: 20 Solid wood max mm: 8 Cutting scissors CW: 2.5  ... más información

Code: 0253 Brand: CEHISA Model: BRYKO - CE Standard Automatic edge bander for wood, Pvc, veneer, abs, melamine edges - CE Standard Technical data: Edge thickness min/max 0,4/2 mm Min/max panel height 8-40 mm Min panel length mm 120 Min panel width mm 75 Panel feed speed mt/min 5,5 Composition: Gluing unit: Glue tank with digital thermostat - Automatic feeder for roll and strip edges - 1 motorised roller + 1 idle roller 2-blade End cutting unit with high-frequency motor - Tool rotation speed 12000 rpm Upper and lower trimming unit - Tool rotation speed 12000 rpm Total installed power Kw 2,5 Compressed air 6-7 bar Overall dimensions mm 1800 x 950 x 1200 h Weight kg 430

Code: 0005 Brand: OMMA / OTHER BRANDS 2300 Model: 2300 Nr 2 rubber-coated rollers Technical data Length mm 2300 Diameter mm 230 Rifling 3,4 x 1 cm / 9 x 1" (inch) Overall dimensions of wooden crate for 2 rollers: mm 3000 x 900 x 550 h Weight kg 800  ... más información

BIMATIC edge banding machine model SYNCRO 4105.8 : - Electronically controlled control panel - Usable panel thickness from 8 to 45 mm - Forward speed 10 m/min - Overall dimensions approx. 5.1 x 1.2 x h=1.6 m - machine according to CE standards, year 1998 Operating units: - Gluing unit with: hot-melt glue pot with rapid heating (about 5/6 min.) loader and shear for roll material from 0.4 to 3 mm loader for solid strips up to 8 mm - Double vertical trim panels, 0.3+0.3 hp motors, tiltable 0 - 15° - Overlapping trimmers, non-tilting, 0.5+0.5 HP motors - 0 - 25° tilting trimmers, 0.5+0.5 hp motors - Rounder with 1 engine HP 0.5 - Straight edge sander, HP 2 motor

Edge gluing machine Manufacturer: IMA Model: Compact 508 Built: 1988 Facilities - Caps - Flush milling - Forming milling units - Radius/Chamfer milling - Corner machining - Pulling blade - Schwabbelaggregate  ... más información

Edge banding machine Cehisa SYS 5PS - Only about 60 km edges glued / little used! - Condition tiptop - Sturdy construction all important aggregates available: - Infeed ruler - Joining milling - Preheat plate - Glue application - Apply edges (rolls or strip magazine) - Pneumatic pressure roller driven - Pressure roller on top, spring-loaded - Pressure roller at the bottom, spring-loaded - Caps front & rear - Flush milling top and bottom - Copy corners front and back -Scraper - Schwabbelscheibe Accessories: -Tool - Feed rollers for various edge materials - various spare blades - Settings folder Year of construction 2008 Masch. No. 532 The machine is approx. Available at the beginning of October (probably earlier) and would then have to be picked up on a fixed date. Disassembly and collection by buyers The machine is in top condition, ready for  ...

single-sided edge banding machine with pull-out workpiece support, end trimming unit and combi-unit. Power consumption: 400 V / 50 Hz / 3 pH / 7 kW Compressed air supply: 6 bar Dimensions: approx. 4,000 x 1.300 (1,780) x 1520 mm Edition extendable to 800 mm Working height: 820 mm Roller plate ø 700 mm

Equipment/technical data: - e-Motion control with 21" smartouch instead of 10" tempora F 800 Ser - Upper pressure beam motor-controlled, adjustable workpiece height 8-60 mm - Chain feed 12 m/min, 1.5 kW, Minimum workpiece length 140 mm - Turntable edge magazine for roll edge material 0.4 - 3 mm and strip magazine for 12 pieces 10 mm edges - Edge feeding for roll and strip material - pneum. Controlled gluing unit, Teflon-coated, for 1.5 kg EVA granules, with synchronized glue roll and quick-change system. (for PUR adhesive processing, taking into account the Adhesive processing guidelines) - Pneumatically operation-controlled pressure unit e-motion (one driven, two conical contact rollers) tempora 60.12/2: 0-12mm - Impact shears for roll material - Cross-cut saw with 2 motors - Joining milling unit 2 x 1.5 kW - Upper and lower combination milling unit, 0.75 kW each, flush a ...

Code: 0233 Brand: MCR - ITALY Model: EASY EDGE/5 - CE Standard Automatic edge bander for edging panels, veneer edges, PVC, solid wood, abs, etc. - CE Standard Technical data: Max edge thickness mm 5 Max panel height mm 80 Min panel height mm 10 Min panel width mm 80 Adjustable feed speed Composition: Gluing unit: Heat regulator glue tank - Heat regulator roller - Automatic strips loader End cutting unit consisting of 2 motors of 0, 37 kW - Blade diameter mm 125 - Blade inclination Fine trimming unit :allows the trimming of the top and the bottom of the applied edge - 2 motors Kw 0,37 - N° 2 combined Vidia cutters with inserts to 30° plus flat sharp Polishing unit - N° 2 motors - Brush diameter mm 160 Control panel Sound-proof cabin Total absorption A 10 Overall dimensions mm 3100 x 1000 x 1640 h Weight kg 950

Edge height max. 65 mm Edge thickness max. 20 mm Strip cross-section max. 20 x 55 mm Fixed workpiece protrusion in post-processing incl. Edge material 38 mm (max. edge thickness 8 mm) In the case of strips or edge thickness > 8 mm, the output is in of post-processing 30 mm + strip thickness Post-processing is then only possible with the following units: possible: cross-cut and milling unit 08.055 and grinding unit Feed speed 6 - 30 m/min. Roller support rail extendable up to 700 mm Machine length 9,300 mm IMATRONIC 121/01 with system software for operating the Edge banding machine Compact PC in industrial design Electronic height adjustment of the upper pressure Inlet ruler axis-controlled Milling unit 08.376 with 2 motors of 4.5 kW each, in the Working in sync or counter rotation Infrared emitters for workpiece edge preheating Gluing unit 283.151 ...

Equipment: - Quickmelt gluing part for hot melt adhesive - Automatic edge magazine for rolls and fixed lengths - Heavy pressure zone with driven, pneumatically applied main pressure roller and 2 free-running repressure rollers. (adjustable by program) - motor-adjustable upper pressure. - Control panel on the machine inlet. - Electronic control power control PC 20+ - Feed variable 8-14 m/min - PU overpressure rollers - Inlet ruler adjustable by program - Joining milling unit 2 x 2.2 kW - Bevel cross-cut unit/straight 2 x 0.18 kW - Milling unit 2x0.55 kW (adjustable by program) with multiple roller pressing - Mould milling unit top+bottom, 2 x 0.35 kW - Drawing blade with quick-change heads and additional device for pointed workpieces - Glue joint drawing blade - Schwabbelaggregat - Automation package for 1-milling machines, consisting of: 3175 - Pneumatic Adjustment Caps ...

Overview of the assembly: - Release agent spray unit top & bottom - Joining milling unit 2 x 4 kW - Glued part with workpiece preheating, 2 rolls, pressure zone C and QA34 application unit for PU with quick clamping system - autom. Adjustment pressure zone - Preparation for Lasertec activation unit - Hl84 cross-cut unit 0.8 KW - pneum. Adjustment pre-milling unit - Pre-milling unit Bf10 1.5 kW - Mould milling unit Fk11 Manual - Autom. Adjustment of chamfer to radius milling machines - Rolling side probe FK - Pneumatic adjustment FA11 for lateral displacement from the working area - Multi-drawing blade MN 21 autom. for a maximum of 5 different profiles. - Finishing unit (glue joint drawing blade and swabbing ridge) - Detergent spray unit top & bottom - powerControl PC22 Workpiece and edge parameters: - Workpiece width without edge min: - For workpiece thickness  ...