Fabricante:
(Categoría: 307)
roll diameter: 550 mmroll length: 1500 mmrolls drilled: Kernbohrung Nip adjustment: hydraulisch 0total power requirement: 90 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
roll diameter: 150 mmroll length: 300 mmrolls drilled: Flaschenhals Nip adjustment: hydraulisch total power requirement: 4 kWcondition: used, overhauledSpecification: Laboratory Rolling Mill 150 x 300 mm - second-hand Motor under the rollers- Roller diameter approx.: 150 mm- roller length: 300 mm- Friction between the rollers- Rolls drilled with central chamber for water cooling- Rolls with new slewing rings, manufacturer MAIER, for water cooling,- Rollers mounted on bronze bushes with circulating oil lubrication via pump,- Gap adjustment: NEW, hydraulic and as emergency system- Hydraulic unit NEW- NUE Tilting guide plates- NEW safety cage- Safety brake for emergency stop- AC brake motor: 4 kW - 400 Volt - 50 Hz- new mixing tanks made of stainless steel for the mixture- Safety devices according to current EN 1417:3/2015- Painting: in RAL colours according to ...
roll diameter: 400 mmroll length: 1000 mmrolls drilled: Kernbohrung Nip adjustment: hydraulisch 0total power requirement: 45 kWCondition: used, overhauledSpecification: Rolling mill 400 x 1000 mm - second-hand monobloc model, motor under the rolls- roll diameter: 400 mm- roll length: 1000 mm- rolls: with core bore, with central chamber for water cooling- Rollers mounted on bronze bushes with oil circulation lubrication via pump,- equipped with new slewing rings for connection to the water circuit- Gap adjustment: hydraulic, NEW- Hydraulic unit NEW- Tiltable guide plates- stainless steel roller container to hold the mixture- bi-directional rods- safety brake for NOT stop- AC motor: 45 kW - 400 Volt - 50 Hz- Painting: in RAL colours according to customer ...
screw ø:: 90 mmscrew length:: 20D screw speedl:: 0 - 60 U/minCondition: NEW,Specification: Rubber vacuum extruder - with warranty- Screw diameter: 90 mm- Screw length: L = 20 D (approx. 1,800 mm conveying length)- Screw speed: 0 - 60 rpm- Centre height of extruder: approx. 1,125 mm incl. base frame- Max. permissible injection pressure: 500 bar- with feed roller- Extruder water-tempered- Extruder base frame as welded construction, to accommodate the extruder with drive motor, the temperature control, the vacuum pump- Funnel piece with intermediate flange: two tempering zones approx. 4D = 480 mm- Vacuum cylinder: three tempering zones BL = 1,057 mm- End cylinder: one temperature control zone ...
Press force max.:: 5.000 kNheating plates:: 1100 x 1200 mmelectrically heated:: °Cpiston stroke:: ca. 620 mmCondition: used, overhauled 2021Specification: Vulcanising press 1100x1200 mm, Panel structure, used- closing force approx.: 500 t- Closure: from bottom to top- 2x heating plates: with new resistors- heating plates: electric plates- Dimensions heating plates approx.: 1100 x 1200 mm- clear width between the heating plates approx.: 750 mm- piston stroke approx.: 620 mm- Additional panel for 0-closure between the Plates- New electric valves- AC machine power AC motor: 15 kW- New control cabinet with Siemens 7 touch panel- PLC system Siemens S7-1200- Frequency converter: make Schneider- New cabling 2021- Light curtains at the front- CE marking form 2021- Operating and main ...
cross-section width:: -- mmcross-section heigth:: -- mmfeed:: -- mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
cross-section width:: 100 mmcross-section heigth:: 40 mmfeed:: 2 - 999.999,9 mmCondition: new,Specification: Impact knife cutting machine CC-600/40 for hoses and profiles- contact length: 600 mm- product diameter: 40 mm- belt width: 100 mm- Tractive force: 400 N to 800 N- Drive: 2 drives upper and lower belt- Conveyor belt speed: 100 m/min- Drive feed, cutting motor: Servo drives- Cutting capacity with blade max.: 4,000 1/min- Connected load: 3.5 kW- Dimensions L/H/B: 1,900 x 1,650 x 960 mm- Weight approx.: 580 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
machine measurements: 850 x 1.800 x 1.450 mmmachine weight: 360 kgpower capacity: 0,7 kWCondition: newSpecification: Powder coating machine, type: EPC-30/2EThe machine is designed for the powder coating of cables, hosesand profiles.- Product diameter max.: 30 mm- Product speed max.: 1,500 m/min- Powder throughput min.: 30 g/min with fine dosage- Powder throughput max.: 400 g/min per powder injector- Electrostatic: available as option- Connected load: 0.7 kW- Dimensions LxHxW: 850 x 1,800 x 1,450 mm- Weight approx.: 360 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cross-section width:: 85 mmcross-section heigth:: 25 - 40 mmfeed:: 1 - 999,999,9 mmspeed of feed:: 60 m/mincuts max.:: 100 - 120 Schnitte/mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
roll diameter: 400 mmroll length: 1000 mmrolls drilled: Kernbohrung Nip adjustment: hydraulisch 0total power requirement: 37 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
roll diameter: 500 mmroll length: 1500 mmrolls drilled: Kernbohrung Nip adjustment: hydraulisch 0total power requirement: 110 kWCondition: used, overhauled Specification: rolling mill 500 x 1500 mm - used- roll diameter: 500 mm- roll length: 1500 mm- monoblock - motor under the rolls- fixed friction between the rolls- Rolls: with core bore, with central chamber for water cooling- Gap adjustments: NEW hydraulic- Hydraulic unit: NEW- tiltable material guide jaws made of steel- Rollers: mounted on bronze bushes with oil circulation lubrication via pump- new ball bearing slewing rings for connection to water circuit- New safety brake for NOT STOP- New AC motor 110 kW - 400 V - 50 Hz - New pan for receiving the mixture- Safety rods bi-directional- New electrical c ...
roll diameter: 600 mmroll length: 1800 mmrolls drilled: Flaschenhals Nip adjustment: hydraulisch 0total power requirement: 132 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
Moros Alligator Shear Model HF-30 Cutting force 200ton For cutting tyres and bar ... más información
volt: 380 Vweight: 1,4 t: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
Hand Operated Press600mm x 600mm IPW heated platens300mm daylightEurotherm Controllers ... más información
cross-section width:: 800 mmcross-section heigth:: 15 mmfeed:: ab ca. 5 mmspeed of feed:: m/mincuts max.:: Schnitte/mcondition: used, overhauledSpecification: Panel cutting machine - overhauled with CE- Section width max.approx.: 800 mm- Section height max.: 15 mm, depending on the hardness of the rubber sheets- Cutting length from approx.: 5 mm (depending on material)- cutting force approx.: 10 tons - Connected load approx.: 1.8 kW- Painting: green- Operating voltage: 3 x 400V, 50Hz, N, PE- Dimensions approx.: 1,200 x 1,450 x 1,950 mm - Safety devices according to current standards,- New on-board system machine,- New control cabinet with PLC system Siemens S7-1200,- CE marking,- Instructions for use and maintenance in English or German language ...
roll diameter: 700 mmroll length: 2200 mmrolls drilled: Kernbohrung Nip adjustment: hyraulisch 0total power requirement: 160 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
Press force max.:: -- kNheating plates:: 600x600,500x500 mmelectrically heated:: -- °Cpiston stroke:: -- mmno. of stages:: 1-3 Condition: Used,Specification: 5x vulcanising press, second-hand consisting of: 2x make Simpelkamp, 2x make Reinartz, two-daylight presses 1x make Reinartz 1x crane system 1x pedestalsSimpelkamp presses:- Clamping force: 250 t- number of floors: 1- Closing: from bottom to top- Heating plates: 2 electric plates- Dimensions of heating platens: 600 x 600 mm- Distance between heating platens: 530 mm- Hydraulics: 200 bar- AC machine power oil pump: 7,5 kW- Dimensions approx.: 1,300 x 1,000 mm- Unit height approx.: 2,800 - 3,000 mmTwo similar ...
1 x Francis Shaw Model K6 Intermix, Original year of manufacture: 1977, Rebuilt body fitted by Carter serial no. 242.93, Year: 1993, Hydraulic drop door discharge, Mixing chamber volume: Approx 112 litres Pneumatic hopper, 750HP, slip ring motor, 3ph, 50 Hz through Sturdigear 1460/15.7 rpm reduction gearbox (1000HP rating). Complete with hydraulic unit + operator controls etc and in very good condition.
roll diameter: 200 mmroll length: 400 mmrolls drilled: Peripher Nip adjustment: hydraulisch total power requirement: 2x 5,5 kWCondition: new rolling mill, with CE marking, with 1 year warrantySpecification: Monobloc laboratory rolling mill 200 x 400 mm - new- roll diameter: 200 mm- roll length: 400 mm- roll bore: peripherally drilled- Single drives: variable friction ratio- Roller bearing: bearing with grease lubrication- Gap adjustment: hydraulic- new hydraulic unit for roll gap and emergency system- New rotary unions make Johnson-Fluiten- two adjustable guide plates to reduce the to reduce the working area- Stainless steel tank- New safety cage- 2x AC brake motors make Siemens: each 5,5 kW, 400 V, 50 Hz- Painting: with RAL ...