subcategorías
(el tercer nivel de categoría)
Fabricante:
(Categoría: 109)
Pump output: 1362l/h, washing basket dimensions: 920x660x680mm, length: 1150mm, width: 660mm, height: 940mm, weight: 70kg, with documentation. ... más información
Controls: AEG-Elotherm ELOPULS, with documentation. ... más información
Max. operating pressure: 70bar, hydraulic fluid filling quantity: 630l, with loading portal and sliding guide with carriage. ... más información
Bar diameter: 5x5-10x10mm, max. bar length: 3200mm, with Bar Loading Magazine FMB VARIO 3000, length: 6000mm, year of construction: 2001, with built-in shear discs made of through-hardened 1.2767 steel, with fully automatic stroke sequence at a maximum pressure of 120bar, contact stop, preselection counter and hydraulic motor Bauknecht RF3/4-75, with documentation, the machine has been idle for over 10 years, the machine is not functional, the hydraulics and controls are defective.
There are three identical superfinish machines Nagel available, connected load: 11kW, controls: SIEMENS SIMATIC HMI, length: 2565mm, width: 2600mm, height: 2663mm, operational hours counter: 34,051h, year of construction: 2x 2015, 1x 2014, with documentation, there are additionally two automations Promot available.
Heating output: 2000W, ultrasonic frequency: 40kHz, weight: 275kg. ... más información
Power: 5.5kW, length: 2800mm, width: 1300mm, height: 1700mm, weight: 2.7t. ... más información
Mains voltage: 380V, connected load: 13kW, controls: Heidenhain TNC 125, the machine is in very good condition. ... más información
Connected load: 160kVA, length: 8328mm, width: 2768mm, height: 3665mm, weight: 9.5t, with documentation. ... más información
Control panel: Siemens SIMATIC HMI, operational hours counter: 2169h, with Deduster MHG 1703-2,2 and various accessories. ... más información
Description: Serial Number:55DR1663 Max. Workpiece dimensions: 800x600x215 mm Max. Workpiece weight: 500 kg Table dimensions: 640 x 540 mm Travels: X-axis: 400 mm Y-axis: 300 mm Z-axis: 220 mm Table rapid traverse rate: 1300 mm/min Wire diameter: 0,1 to 0,3 mm Max. Wire feed speed: 23 m/min Wire tension: 0,5 to 25 n Taper: OPTOLinear T/C device Taper angle: 15º (with 200mm plate thickness) Working Hours 24073 Dielectric Fluid Reservoir: Working tank volume: 550 litres Filtration flow rate: 50 l/min Water purifier: 10 litres Other features: Superfinishing Rugosity less than Ra 0.2 weight approx.: 2,980 kg, Approx. Onsite Dimension. (l x w x h): 1,910 x 2,702 x 2,015 mm
Unused 1 full pack with 16 plates 2000 mm x 1000 mm 6 mm thick Nett weight 1542kgs ... más información
Description: STRAMA camshaft cleaning system The cleaning system is suitable for cleaning camshafts or parts with smaller physical dimensions. , Camshaft cleaning was last carried out on the system. The machine is currently out of service. A brief description of how the machine works: A handling robot with a 3-finger centric gripper takes the camshafts automatically. The robot feeds the camshaft to the cleaning, drying and vacuum drying stations one after the other. The cleaned and dried shaft is then automatically deposited by the robot in a removal station. , The cleaning system consists of the following components: Transfer with robot from workpiece carriers Cleaning stations: Cleaning, blowing off / drying and vacuum drying Removal station (depositing by robot) Handling robot with gripper (robot type: KUKA, KR30-3 Foundry) Soundproof enclosure Tank, filter and pump equipment ...
Continental 125/40-90 x 4 Colson 40-25 x 3 Promlus Rollen x 1 Excluding Box ... más información
Description: The used PMM-F is specially designed for testing medium-sized components and gears. This 3D measuring machine has an overhead design and serves as a coordinate measuring machine, gear measuring centre, form tester and roughness measuring machine. Area of application: Inspection of medium-sized components and gears Design: Overhead design Functions: Coordinate measuring machine, gear measuring centre, form tester, roughness measuring machine Measuring range: approx. 3,000 x 2,000 x 1,600 mm Resolution: 5 nm Equipment: Various measuring probes Accessories: Work table, mobile container, chair Control desk: Equipped with a Dell PC The PMM-F offers a precise and versatile solution for measuring and testing components and gears in medium dimensions.z-motion: 1,000 mm, x-motion: 3,000 mm, y-motion: 2,000 mm, table surface area l x w : 3000x2000 mm, weight approx.: 32,000 kg, Appr ...
Trumpf TruPunch 3000 medium formatPunching pressure: 180 kN Max sheet thickness by punching + nibbling: 6,4 mm Max weight workpiece: 160 kg Working range on cross-side (X-axes): 2550 mm Working range along (Y-axes): 1280 mm Positioning speed along X-axes: 90 m/min Positioning speed along Y-axes: 60 m/min Control: Bosch CNC Toolchanger: 19 tools Number of toolpositioners: 10 stations Changingtime: 0,3 / 3 sec Power needed: 5,9 kW Length: 5000 mm Depth: 6500 mm
Description: The almost new 8 MW transmission test station is operated from a central control station. Some of the test energy input can be fed back into the power network. Inventory number: 9000945 , Year of construction: 2018 Data on the three-phase asynchronous machines Nominal output: 7.7MW Maximum output: 8.47MW Nominal speed: 1150/min Maximum speed: 2200/min Nominal torque: 63940 Nm Maximum torque: 70330 Nm Main shaft data Nominal speed: 8.99 rpm Nominal torque: 6000kNm Maximum torque: 8800kNm Cooling system Cooling capacity of the cooling tower: 900kW Coolant volume flow: 160m³/h at 4 bar and 30°C Nominal pressure hydraulics Hydraulic system main shaft: 250 bar at 100 l/min Hydraulic system quick coupling: 300 bar at 1 l/min Hydraulic system generator (lifting/lowering) 150 bar at 8 l/min Oil system: 8 bar at 120 l/min General data Operating voltage: 3.3kV Auxilia ...