otras máquinas para el procesado de metales usadas para la venta

wire dia.: 5 - 17 mmwire length: max. 5.000 mmstraightening feed: stufenlos bis ca. 60 m/min: 11 kW, 380 V, 50 Hz : 45 kW, 1480 U/min, 380 V, 50 Hztotal wight: ca. 15 t: Typ DZA/20 f. 1000kg Coil The data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información

round bar steel: 63 mmsquare edge steel: 55 mmflat steel: 100 x 25 mm: engine: 380 V, 6,3 kW weight: ca. 2.450 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información

max. wheel diameter: 400 mmgear width: NA mmmax. module: 1 min. module: 10 total power requirement: 12 kWweight of the machine ca.: 4,2 tdimensions of the machine ca.: mK L I N G E L N B E R G (Germany)Automatic Bevel Gear Lapping MachineModel LKR 400 A 100 Year 1974/1998 Serial No. 1890Partially reconditioned and electrically modernized in 1998 by Welter Company_______________________________________________________Max. Ø of crown gear 400 mmAdjustment of pinion spindle 160 / 250 mmAdjustment of crown gear spindle 115 / 265 mmAdditional movements:Axial / distance / vertical, approx. + / - 2 mmAutomatic tooth clearance 0 - 0.6 mmModule 1 - 10Axial offset, up / down, each 50 mm(= axial offset travel from middle position)Bore hole of driving spindle 100 taperBore hole of driven spindle 60 taper6 spindle speeds ...

Cutting cutter Kjellberg-Eberle - used Type: SII20 Machine No.: 1331 - 220 V, 50 Hz, 2.5 kVA, IP 31 - on 04.02.1990 a new control system (NS 3003) was installed by Etek - Built in 1974 - 4 burners - Table dimensions: 6m x 2.50m - Total area: 6m x 5.5m x 2.4m In good condition!

table dimensions 450x350 mm X, Y, Z axis travel 270x170x200 mm weight 300 kg ... más información

Drill grinding machine HAARMANN type HSP 30 Fabr. No. 7925 Year of construction 1974Drill diameter max. 30 mm Grinding wheel diameter 200 mm Grinding wheel width 30 mmGrinding spindle speed 1400 / 2800 rpmMotor power 0.55 kWMains connection 380 Volt, 50Hz- Drive via hand crank- movement via cam disc- tip angle infinitely adjustable- Diamond dresser holder- 5 different cam discs Space requirement L x W x H 870 x 650 x 1450 mmWeight approx. 250 kggood condition; used

max. wheel diameter: 400 mmgear width: 75 mmmax. module: 0,5 min. module: 60 total power requirement: 25 kWweight of the machine ca.: 7 tdimensions of the machine ca.: mL O R E N Z (Germany)High Performance Automatic Gear ShaperModel LS 400 Year 1975 Serial No. 12 592 ______________________________________________________________________ ___________External gear, max. Ø 400 mm (possibly larger)Internal gear dia. 350 mmGear width, max. 75 mmModule range 0.5 - 6Length of stroke 82 mmAdjustment of stroke position 0 - 100 mmDistance between shaper spindle and machine body 250 mmSpindle taper MK 5No. of strokes, roughing/finishing process 118 - 1,000 per minTable size 400 mmTable bore 125 mmMounting height between table and shaper head 190 / 290 mmAxial tra ...

Groove butt head for milling machine, milling head, CCCP / USSR STANKO Type 1502Nr: 200 Year of construction 1974Stroke size: max. 60 mmNumber of strokes: approx. 200 - 500 strokes/min. Tool holder: 12 x 17 mm with clamping plate Hole spacing machine flange plate: 245 x 185 mm Mounting hole: 17 mm Centering diameter on the machine flange plate: 190 mm- Stroke size adjustable via eccentric adjustment- As with the normal vertical head, the drive can be swivelled continuously from the machine gear drive via driver, centered in the centering diameter- Degree scaling on the flange plate+/- 45 - This groove butt head is flanged in place of the normal vertical milling head (assembly in place of the vertical milling head, milling head)Weight: 42 kggood conditionGroove butt head stock number 58166 and vertical milling head stock number 58164 from identical STANKO milling machine.; used

Catalog No. : 7281 Type: 2200 Producer: Emba Made in: 1974 Characteristic: In good technical condition.  ... más información

diameter range 0,8-3,0 mmcutting length 30 mmshaft length under head 25 mmoutput - pieces/min 600 ... más información

Roundness Tester Brand: Taylor Hobson Type: Talyson 3 Year of construction: 1974 Operating instructions Calculator Data backup discs All information without guarantee ... más información

Wire range: 1.8 - 3.8 mmmesh width: 20 - 80 mmworking width: 800 - 2,000 mm capacity: max. 180 m2/hour; ready for use  ... más información

diameter range 2,5-6 mmshaft length under head 80 mmmax. thread length 40 mmoutput pieces/min 600 ... más información

vibratory feederdiameter range 2,5-6 mmshaft length under head 80 mmmax. thread length 40 mmoutput pieces/min 600 ... más información

 ... más información

Vertical milling head, milling head, angle milling head CCCP / USSR STANKO Type 1905 Product No: 393 Year of construction 1974 Tool holder: MK4 Hole spacing Machine flange plate: 245 x 185 mm Mounting hole: 17 mm Centering diameter on the machine flange plate: 190 mm- Drive via carrier, centric in centering diameter- Degree scaling on the flange plate 4x 90 rotatable- Degree scaling on the angle head +/-90 swivelWeight: 65kggood condition Slot butt head bearing number 58166 and vertical milling head bearing number 58164 of identical STANKO milling machine.; used

stroke: 300 mmweight: 900 kgYear: 1975 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información

Article number: 01-08-002 Manufacturer: Profile bending machine Good general condition Machine workshop-tested Shipping time: All rights reserved. Year of construction: ca.1975 L x W x H: approx. 800x600x1000mm Weight: approx. 150kg Control: conventional Max. bending capacity (steel): approx. 150x10mm Max. bending capacity (stainless steel): approx. 150x5mm Number of reels: 3 pieces Bending Process: Forward/Backward Rollers Ø: approx. 100 mm / 75mm Distance between lower rollers: approx. 380mm Distance of top roller: approx. 0-70mm Drive power: approx. 2.0kW Other accessories on request Price and other technical data on request

max. wheel diameter: 400 mmgear width: 0 mmmodule: pinion diameter - max.: 254 mmaxial cross angle: 90 °total power requirement: 15 kWweight of the machine ca.: tdimensions of the machine ca.: mThis machine is very suitable for precision production testing of spiral and hypoid bevel gears with shaft angle 90°. The gear spindle is vertical and the pinion spindle is horizontal. The pinion cone distance can be adjusted while the machine is working in order to find the optimal mounting position whereby the gear is loaded with a preset torque. The axial pinion position can be adjusted until the quietest meshing position of the traction flank is found. Likewise, the thrust flank can be tested during the return run. Marking compound is sprayed on both sides of the teeth so the flank contact pattern can be seen. Working cycles, as well as the positioning in the tooth gap, are automatic ...

single spiralwire diameter 1,5-3,4 mmmesh width 30-70 mmworking width 2000 mmcapacity - m²/hour 85tooling for mesh width 50 mm ... más información