subcategorías
(el tercer nivel de categoría)
Fabricante:
(Categoría: 109)
The FORNI INDUSTRIALI FIBEX COMBI 6GX-10.130-7110.2E.270 brazing furnace was built by the Italian company Forni Industriali Heat Treating Plants in 2007. The furnace is used for soldering steel elements with solder paste at temperatures up to 1120 degrees Celsius. At the entrance and exit of the furnace, two pairs of gas burners (so-called safety pilots) are installed to prevent the escape of the protective atmosphere outside the furnace. Electric heaters powered by thyristor temperature regulators are responsible for the proper temperature in the furnace. The belt furnace has a conveyor speed adjustment in the range from 0 to 500 mm / min, and the working length of the soldering zone is 7100 mm. The furnace for brazing steel elements was modernized in 2021 - the thermal insulation and the cooling module for sections 1 and 2 were replaced. The cost of the modernization was 70,000 Euro. ...
The CIMAT CMT 30 V2 balancing machine was manufactured in 2015 in Poland. Bvcilkrj7m Basic technical data: - software: ROTOTEST - component weight: 0.2 to 30 kg - maximum rotor diameter: 400 mm - maximum rotor height: up to 200 mm - compressed air pressure: 0.6 MPa - balancing machine dimensions: 1200 x 1200 x 1500 mm - control panel dimensions: 600 x 600 x 1800 mm - weight: 500 kg
ERMAKSAN LASERMAK 6000 6X2 laser cutter was produced in 2014. Technical parameters: – laser source: 6000 W CO2-laser GE Fanuc C6000i-Model C – RF-excitation: 2 MHz – power stability: ± 2% (power monitor) – laser wave length: 10.6 μM – beam mode: Fanuc Low Order Mode – laser shutter: mechanical safety shutter – laser gas composition: CO2 / He / N2 – gas consumption by laser: 20 l / h – cooling water flow rate: 250 l / min – maximum cutting capacity: mild steel 25 mm (during tests the maximum achieved: 30 mm), stainless steel 15 mm, aluminum 12 mm - machine activation time: 22899 h - working time: 10122 h - cutting time: 8429 h – total energy requirement: 100-120 kW – cutting head focal length: 5 -7” -10 inch – maximum worksheet size: 6150 x 2000 mm – maximum burden capacity: 4000 kg – machine axes: 5 axes [X, Y, Z, U (X2), V] – axis ...
Gabion Mesh Production Line HEBEI ANPING WIRE MESH MACHINE FAKTORY 60X80 / 4300 was built in 2013. Machine for the production of hexagonal gabion mesh with the following parameters: - manufacturer: Hebei Anping Wire Mesh Machine Faktory (China) - mesh size: 60 x 80 mm or 60 x 100 mm - maximum width of the produced mesh: 4300 mm - wire diameter: 2.0-2.8 mm - capacity: up to 2.5 m / min - machine weight: 18 tons - engine power: 22 kW
Hardening furnace ZWUT PSK-1 built by ZWUT. It is intended for various types of laboratory and industrial work. Technical data : - power consumed at T = 1350 degrees C: 4,10 kW - installed power: 5.5 kW - power supply voltage: 220 V, 50 Hz - secondary voltage of the autotransformer: 7-41, 1-3-58, 9-5-84, 4 - number of phases: 1 - nominal temperature: 1350 degrees Celsius - temperature control accuracy: 1.5 (or 0.2 + /%, when working with a feedback attachment) - type and number of silites: 8/150/150/10 mm / pcs - warm-up time to T: about 3.5 hours - usable dimensions of the heating chamber (height x width x length): 150 x 150 x 280 mm - furnace weight: 138 kG - weight of the cabinet: 81 kG
Wire EDM machine SODICK A 600 manufactured in 1997. Technical parameters of the SODICK A 600 EDM machine: - table travel (X axis): 600 mm - table travel (Y axis): 400 mm - Z axis travel: 270 mm - maximum dimensions of the processed part (width x depth x height): 800 x 550 x 260 mm - maximum weight of the workpiece: 900 - auxiliary table travel (U axis x V axis): 70 x 70 mm - wire diameter: 0.1 ~ 0.3 mm - maximum wire speed: 250 mm / sec. - wire tension: 0.2 ~ 2.8 kgf - cutting inclination at an angle: + -15 degrees per 100 mm of thickness - height from the floor to the surface of the working table: 1000 mm - machine tool dimensions (width x depth x height): 2188 x 2645 x 2100 mm - machine tool weight: 3700 kg
Ultrasonic cleaner GT85 GT 2000-3P built in 2008. The washing tub is made of 316L stainless steel, the other tubs are made of 304 stainless steel and the supporting structure is made of structural steel. The volume of washed products should not exceed (LxWxH) 2400 x 600 x 600 mm Industrial washer - technical data: - external dimensions (LxWxH): 6400 x 4400 x 2800 mm - usable dimensions: chamber I (washing and phosphatizing): 2800 x 800 x 900 mm - useful dimensions: chamber II (rinsing): 2800 x 800 x 900 mm - usable dimensions: chamber III (drying): 2800 x 800 x 900 mm - power consumption: 63 kW - total weight: 2500 kg Bathtub 1: - preparation type: Ruster P02, Roklin P11 - pH: 2-4 - bath operating temperature: 20-60 degrees C - total bath capacity: 2000 l - maximum product weight: 500 kg - maximum product volume: 250 dm3 Bathtub 2: - type of preparation: tap water ...
General: Control Sodick LN2W Travel X/Y/Z axis 600/400/270 mm Travel U/V axis 80/80 mm Workpiece height max. 265 mm Workpiece weight max. 850 kg Wire speed 420 mm/s Wire diameter 0.1 - 0.3 mm Equipment: Wire Storage Jumbo feeder Dielectric tank 890 l Set-up operation manual control unit
Urpe M200 vertical slotting machine. Travel: 0-200mm. Table size: 650x220mm. Strokes per minute: 40-55-75. With chuck. ... más información
Stock number: 3884 CNC WIRE EDM MACHINE Manufacturer: Brother , Type: HS 50A Machine NO.: 111136, Year of manufacture: 1999 Specifications: Large workpiece dimensions W 580 x D 350 x H 170 mm Longitudinal movement (X) 410 mm Transverse movement (Y) 260 mm Vertical movement (Z) 170 mm U Travel +/- 32.5 mm V TRavel +/- 32.5 mm Length: 1700 mm, Height: 1962 mm, Width: 1040 mm, Weight: 1300 kg
From insolvency: Gläsner ECO 1000 Year of construction 2011 Total dimensions: 2050x1100x1700mm Aperture 880x790mm Lighting ... más información
Measuring range 1000,1200,600 mm Measuring Head type VAST XXT Software CALYPSO 2017 Version 6.4.02 ... más información
Circulating air chamber furnace, make SAT Temperature: 200°C Useable dimensions (B x T X H): 4000 x 2100 x 2300 mm Overall dimensions (B x T X H): 20000 x 5000 x 4000 mm (input table + oven + cooling cell + output table) Fans: 2 x 4,4 kW Heating power: 168 kW Total power: approx. 200 kW
Reinforced steel scissors Round iron scissors Scissors Manufacturers Muhr and Bender Type 50N/22 and 50N/28 50N/22 intersects at 450N/mm2: Round: 22mm Square 22mm Flat: 35x10mm 50N/28 intersects at 450N/mm2: Round: 28mm Square 24mm Flat: 40x15mm Both machines new and ovp Special price
Portable Leybold Helium Leak Detector Ultratest UL100Plus ... más información
Thread edge with extensive accessories, by hand or automatically to use. Table model, mobile also for the construction site Manufacturer GF Georg Fischer Table model with electric drive or by hand. Automatically opening thread cutting head Threaded jaws for: 1/2 inch, 3/4 inch, 3/8 inch, 1 inch, 1 1/2 inch, 2 inch Machine in transport box (steel) Rems Tornado Klauke Rothenberger Supertronic Special price
Parts cleaning system Industrial washing machine degreasing made entirely of stainless steel! Manufacturer Render Type W175 Built: 1994 5 loading trolleys with 5 washing baskets, Basket size 1,125 x 1,125 mm Manual workstation with viewing window on one side with integrated high-pressure cleaner. Machine to be loaded/unloaded from both sides! Machine comes from an operating resolution and was in use until dismantling. Tank capacity approx. 2,000 litres, oil scimmers, filters, high-pressure pumps... Vertical door opening (lifting doors) on two opposite sides. This allows you to load on one side and unload on the other side. Due to the very high inner height, the system offers an optimal possibility to accommodate both very heavy laundry material as well as parts with large dimensions.
Industrial washing machine degreasing Disse GmbH Industrial washing machine for cleaning and degreasing machine parts of all kinds Rotary basket diameter approx. 95cm Two pneumatically opening doors on each side for: dirty side / clean side Outer mass Height approx. 240cm Width approx. 120cm Depth approx. 140cm Weight approx. 800kg
Waterjet cutting system mobile Manufacturer Schmidt, Krantz & Co GmbH / Woma Maximator WS103 HFA-HD-Aggregat Maximator waterjet cutting system Waterjet cutting with 2,500bar Foerder power 2.3l/min Cutting head handbetaed, manufacturer Woma Weight 1,000KG External hydraulics with max 350 litres of foerder power required, not included!