Fabricante:
(Categoría: 307)
machine measurements: -- mmmachine weight: -- kgpower capacity: -- kWCondition: used, Specification: drum-type blast deburring machine type: MEWO Rotor TS 60- batch volume approx.: 1-600 litres,- working temperature: - 150°C- drum speed: 5 - 30 rpm- Blast wheel speed: 1,000 - 9,500 rpm- Control: Siemens S7 SimaticThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cross-section width:: 700 mmcross-section heigth:: 500 mmfeed:: -- mmCondition: used, overhauledSpecification: splitter for rubber bales - overhauled with CE- cross section width max.ca.: 700 mm- cross section height max. approx.: 500 mm- cutting force approx.: 10 tons - AC motor: 4 kW, 400 V, 50 Hz- Infeed roller conveyor for product transport- Machine stands on a raised pedestal- Two-hand safety control for driving the blade movement- Safety guard according to current standards- New control cabinet- New on-board system machine- Operating and maintenance manual in English- CE marking- Paintwork: according to customer requirements- Refurbished with 1 year warranty- CE marking,Option:- Output roller conveyor newThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
machine measurements: 850 x 1.800 x 1.450 mmmachine weight: 360 kgpower capacity: 0,7 kWCondition: newSpecification: Powder coating machine, type: EPC-30/2EThe machine is designed for the powder coating of cables, hosesand profiles.- Product diameter max.: 30 mm- Product speed max.: 1,500 m/min- Powder throughput min.: 30 g/min with fine dosage- Powder throughput max.: 400 g/min per powder injector- Electrostatic: available as option- Connected load: 0.7 kW- Dimensions LxHxW: 850 x 1,800 x 1,450 mm- Weight approx.: 360 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cross-section width:: 100 mmcross-section heigth:: 40 mmfeed:: 2 - 999.999,9 mmCondition: new,Specification: Impact knife cutting machine CC-600/40 for hoses and profiles- contact length: 600 mm- product diameter: 40 mm- belt width: 100 mm- Tractive force: 400 N to 800 N- Drive: 2 drives upper and lower belt- Conveyor belt speed: 100 m/min- Drive feed, cutting motor: Servo drives- Cutting capacity with blade max.: 4,000 1/min- Connected load: 3.5 kW- Dimensions L/H/B: 1,900 x 1,650 x 960 mm- Weight approx.: 580 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 400 mmroll length: 1000 mmrolls drilled: Kernbohrung Nip adjustment: hydraulisch 0total power requirement: 45 kWCondition: used, overhauledSpecification: Rolling mill 400 x 1000 mm - second-hand monobloc model, motor under the rolls- roll diameter: 400 mm- roll length: 1000 mm- rolls: with core bore, with central chamber for water cooling- Rollers mounted on bronze bushes with oil circulation lubrication via pump,- equipped with new slewing rings for connection to the water circuit- Gap adjustment: hydraulic, NEW- Hydraulic unit NEW- Tiltable guide plates- stainless steel roller container to hold the mixture- bi-directional rods- safety brake for NOT stop- AC motor: 45 kW - 400 Volt - 50 Hz- Painting: in RAL colours according to customer ...
roll diameter: 560 mmroll length: 1500 mmrolls drilled: Peripher Nip adjustment: hyraulisch 0total power requirement: 150 kWCondition: used, completely overhauled, with warrantySpecification: rolling mill 560 x 1500 mm - used model external gearbox - motor sideways placed at the machine- roll diameter: 560 mm- roll length: 1500 mm- model: Duplocom / pluridrive- Peripherally drilled rollers for water cooling- Cardan joints between gearbox and rollers- Individual drive for the rollers, for variable friction- hydr. gap adjustment- Hydraulic unit- Tilting steel guide plates- rollers mounted on roller bearings with appropriate lubrication- rollers with new ball bearing slewing rings, make Maier, for the connection to the water circuit- One gearbox- two individual drives, each with: 2x 75 kW - 400 V - 50 ...
Three Roll Calender Manufacturer Iddon Bros. ‘I’ shape stack vertical Roll width 54” (1350mm) x 22” (550mm) diam. Even speed Rotary joints for steam heated rolls for water cooling Electrical speed controls with electric autostop Motorised roll stack at the end of the Calender Complete with gearbox, 45kW motor and starter panel The Calendar runs well and goes down to .8mm thick The Calender is mounted on a one-piece fabricated bed plate
roll diameter: 550 mmroll length: 1500 mmrolls drilled: Kernbohrung Nip adjustment: hydraulisch 0total power requirement: 90 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
roll diameter: 150 mmroll length: 300 mmrolls drilled: Flaschenhals Nip adjustment: hydraulisch total power requirement: 4 kWcondition: used, overhauledSpecification: Laboratory Rolling Mill 150 x 300 mm - second-hand Motor under the rollers- Roller diameter approx.: 150 mm- roller length: 300 mm- Friction between the rollers- Rolls drilled with central chamber for water cooling- Rolls with new slewing rings, manufacturer MAIER, for water cooling,- Rollers mounted on bronze bushes with circulating oil lubrication via pump,- Gap adjustment: NEW, hydraulic and as emergency system- Hydraulic unit NEW- NUE Tilting guide plates- NEW safety cage- Safety brake for emergency stop- AC brake motor: 4 kW - 400 Volt - 50 Hz- new mixing tanks made of stainless steel for the mixture- Safety devices according to current EN 1417:3/2015- Painting: in RAL colours according to ...
cross-section width:: 100 mmcross-section heigth:: 50 mmfeed:: 10 - 999.999,9 mmspeed of feed:: 1 - 50 m/minThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
roll diameter: 550 mmroll length: 1500 mmrolls drilled: Kernbohrung Nip adjustment: Hydraulisch total power requirement: 150 kWCondition used, refurbished, Specification Roll mill 550 x 1500 mm - used- roll diameter: 550 mm- roll length: 1500 mm- Variable friction ratio between rolls - cored rolls with central chamber for water cooling- nip adjustment: NEW hydraulical- hydraulic unit: NEW- tipper guiding plates- cylinders: mounted on bronze bushings with forced oil lubrication by pump, new rotary joints for connections to water circuit- N.2 safety brake for emergency stop - N.2 AC engine 75 kW – 380 V – 50 Hz- mill tray to contain compound- bi-directional bars for safety system- visualization display to monitor gap between rolls an ...
machine measurements: 1500 x 2400 x 1150 mmmachine weight: -- kgpower capacity: 12 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
0: 200 °CTorque: - 0Dimensions (HxWxD): 680 x 1320 x 760 mmweight: 177 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
Press force max.:: 3000 kNheating plates:: 600 x 630 mmelectrically heated:: °Cheating power:: kWpiston stroke:: 420 mmno. of stages:: 1 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
roll diameter: 700 mmroll length: 2200 mmrolls drilled: Kernbohrung Nip adjustment: hyraulisch 0total power requirement: 160 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
0: 230 °CTorque: - 0Dimensions (HxWxD): 680 x 1320 x 760 mmweight: 177 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
screw ø:: 120 mmscrew length:: 17D screw speedl:: 42 U/mindrive power:: 138 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
roll diameter: 250 mmroll length: 500 mmrolls drilled: Kernbohrung nip adjustment: mechanisch drive power:: kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
machine measurements: 3.000 mmmachine weight: -- kgpower capacity: 90 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información