trabalho de chapa metálica usadas para venda

sheet width - max.: 1255 mmplate thickness: 4,0 mm STplate thickness: 2,0 mm VAplate thickness: 6,0 mm ALUnumber of strokes - loaded: ~ 66 Hübe/min.cutting angle: 1,5 °total power requirement: 5,5 kWweight of the machine ca.: 2600 kg.range L-W-H: 2300 x 1800 x 1800 mm Machine from a technical college - prototype construction very well-maintained condition ()Furnishing:- electro-hydraulic guillotine shears- manual backgauge with analogue position display (scale + magnifying glass)- electrical cutting length limitation- manual cutting gap adjustment- 1x extra long side stop- 2x extra long support arms- 1x free moving footswitch- rear sheet metal slide- User manual (PDF) Machine link :http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=100 8-9325278The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 4,0 mm STplate thickness: 3,0 mm VAtable-size: 1200 x 780 mmblade length: 200 x 200 mmstrokes per minute: ca. 60 minangle adjustable from - to: 15 - 150 Gradengine output: 4,0 kWweight of the machine ca.: 1200 kgdimensions of the machine ca.: 1700 x 1000 x 1500 mmFurnishing:- electro-hydraulic notching machine, with angle adjustment 15° - 150° Angle adjustment by hand wheels- front panel- Plexiglas protection for better transparency- hardened knives also for cutting stainless steel- planed table surface to avoid tilting or slipping of the metal sheet- 2x staking stops with movable and interchangeable stop bars- lateral clippings ejection- free-moving footswitch- Operation manualThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 300 mmcoil weight: 1 tcoil internal dia.: 350-450 mmweight of the machine ca.: 0,5 tdimensions of the machine ca.: BxTxH 1500x1500x1800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... mais informação

sheet width: 300 mmcoil weight: 1 tcoil internal dia.: 350-450 mmweight of the machine ca.: 1 tdimensions of the machine ca.: BxTxH 1500x1500x1800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... mais informação

material width: 1550 mmmaterial thickness: 2,50 mmno. of straightening rolls: 21 sheet thickness - min.: 0,60 mmdiam. of the rolls ca.: 49,46 mmwork speed: 9,3 / 18,6 m/minbarrel length ca.: 1775 mmNo. of supports up/down: je 7 -fach No. of support rolls: 161 total power requirement: 29 kWweight of the machine ca.: 11 tdimensions of the machine ca.: 5,10 x 1,60 x 2,35 m- Infeed and outfeed table- Roller removal device- Control panel attached to the straightening machine- Switch cabinet- Box with 11 spare rollers with a diameter of 49.46 mm- Electric motorized crowning at the bottom- Height adjustment by electric motor- Swivel/tilt device electric motor- ReversibleSwitch cabinet:Weight 150kgL x W x H: 1.20 x 0.40 x 2.10 mTable with conveyor belt:Weight 300kgL x W x H: 3.70 x 2.10 x 0.90 mRollebach:Weight 200kgL x W x H: 2.80 x 1.60 x 0.85 m1 box of straightening rollers - 11 piecesL x W x ...

sheet width: 2000 mmplate thickness: 4,0 mmdistance between columns: 2050 mmroll diameter: 160 mmtotal power requirement: KWweight of the machine ca.: 2,75 tdimensions of the machine ca.: 3,6 x 1,2 x 1,3 mmSheet metal bending machine 3 rollersincl. foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

The machine is in good technical condition. Max. sheet length: 2050 mm Max. sheet thickness: 4 mm. Upon prior agreement, the possibility of an inspection in progress. ... mais informação

material width:203 mmmaterial thickness:0,1 - 1,9 mmfeed length:101 mmweight:0,1 tdimensions (WxDxH):0,5 x 0,8 x 0,5 m ... mais informação

Offer 23476 Specifications: - Max. working width 1020 mm - max. material thickness 3.0 mm - Cutting angle 2.7° - electr. Footswitch - Single stroke – continuous stroke can be pre-selected - Manual backgauge up to 500 mm - Front pull-out sheet metal support - Drive 400 V / 2.5 kW - Space requirement approx. W 1450 x H 1200 x D 1400 mm - Weight approx. 900 kg

Specifications: - Pressure capacity 450 KN - perforates e.B. up to 25 mm Ø in steel 15 mm - Stroke infinitely adjustable 0 to 60 mm - Stroke rate approx. 16 to 47 1/min - Projection 760 mm - Installation height 215 mm - Working height 1150 mm - Drive 400 V / 7.5 kW - Space requirement approx. W 850 x H 1850 x D 1650 mm - Weight approx. 1350 kg - with: - E. foot switch - 20 pieces of various punches + dies

The machine is in good technical condition. Max. length of cut sheet: 3000mm Max. thickness of cut sheet: 12mm Dimensions LxWxH: 3600 x 1600 x 1900mm Weight: 8300kg By prior arrangement, the possibility of a tour in progress. ... mais informação

The machine is in good technical condition. Cutting length 2500 mm The thickness of the cut sheet is 8 mm Steel shear strength 45 kp/mm2 Discharge 300 mm Adjustable angle 2°30- 1°20 Engine 18.5 kW; 1500 U/min El. control pump motor 1.5 kW; 1500 U/min Maximum working pressure 285 kp/cm2 Oil tank volume 225 l Length 3115 mm Width 3078 mm Height 1855 mm Weight approx. 7650 kg

Knee lever shears for sheet metal Cutting length 15 cm maximum sheet thickness 3 mm Built in 1982 L x W x H: 50 x 40 x 150 cm Weight approx. 50 kg The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/Ersatzteile durch MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system+technik GmbH Maschinenbau Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Manufacturer SMT-Pullmax Kumla Model PV 7 H Year 1982 Working length : 3000 mm Max. thickness : 25 mm ... mais informação

- Flat steel shear cuts flat up to 100 x 18 mm - Knife length approx. 250 mm - Profile steel scissors cut angles 90° to 100 x 10 mm 45° to 70 x 8 mm - Bar steel shear cuts round steel 90° to 36 mm Square steel 90° to 30 mm - Notching device sheets up to 8 mm - Hole punch - Pressure capacity approx. 50 t - Projection 350 mm - punched in steel up to 20 mm Ø in 15 mm - Drive 400 V / 3 kW - Space requirement approx. W 1100 x H 1700 x D 2300 mm - Weight approx. 1900 kg

sheet width: 480 mmplate thickness: 3 mmstations: 13 total power requirement: kWweight of the machine ca.: 11 tdimensions of the machine ca.: 15,x2 mNumber of stations 13Number of straightening stations 1Waves 60 mmCenter distance, horizontal 310 mmCenter distance, vertical 110 - 250 mmSpeed approx. 11 m / min.Connected load approx. 20 kWUncoiler (without drive)- Coil- , inside 508/610 mm- Coil weight 3 tFlying hydraulic scissorsRoller set for hat profileThe techn. Data is manufacturer or operator information and therefore for usnot binding. We reserve the right to make an interim sale, it appliesexclusively our businessand conditions of sale.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

material width:250 mmmaterial thickness:0,4 - 3,5 mmno. of straightening rolls:9 straightening roll diameter:30 mmspeed:3 - 15 m/minmaterial thickness at 250 mm material width:3,0 mmmaterial thickness at 200 mm material width:3,5 mmpower capacity:1,8 kWweight:0,9 tDimensions (WxDxH):1,45 x 1,4 x 1,55 m

Roll enlargement and slitting unit The equipment consists of: Walking conveyor Roll turner Unwinder trolley Unwinder Two-position scraper bender Correct-feed rollers Centering rollers No. 1 (RC 8 x 1600) Sheet straightening machine (5x230x1700) Roller conveyor with pressure roller Guillotine shears No. 1 (NNR 10-1700/2) Cleaning device Centering rollers No. 2 Complex for butt welding of strips L-1700-M-Sh Pulling rollers No. 1 Loop table No. 1 Centering rollers No. 3 Pulling rollers No. 2 Centering rollers No. 4 Disc shears Edge-crushing shears NKP 4-500 Roller conveyor idle Loop table No. 2 Separating device No. 1 Pulling rollers No. 3 Guillotine shears No. 2 Device for lane separation No. 2 Winding device Winder assembly Winder pinch roller Folding winder support Winder unloading device Unloading cart Column with rotary console

Technical data: -Bending performance mandrel bending -maximum Rohrdrm at 45 kg / mm² Ã? 60.3 x 3.2 mm -min tube diameter 20 mm -maximum bending angle 180 ° -Bending direction left + right -Modulus 7,8 cm³ -min. bending radius mid-tube 40 mm -maximum bending radius mid pipe 200 mm -Lift length 5000 mm -maximum bending speed infinitely adjustable up to 3 U/min -Drive 400 V / 4 kW -Space requirement approx. B 1400 x H 1500 X 8000 mm -Weight approx. 1200 kg -Automatic. Bending angle before eligibility - hand positioning adjustment, creep speed control

sheet width: 1250 mmplate thickness: 3,0 mmdistance between columns: mmpower requirement: 2,2 kWdimensions: 3,27 x 1,69 x 1,29 mweight of the machine ca.: 1,6 tused compact mech. guillotine shear- strokes per minute: 50The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.