máquinas de corte e de denteamento usadas para venda

frequency:5.000-150.000 Hzweight of the machine ca.:10 tZ-axis:45-50 mmX-axis:pneumatisch working lenght:45-50 mmwith induction generator Sinak 100PH CN: 26811/100014 built in 2006 with belt filter press Heat exchanger and hydraulic unit  ... mais informação

max. wheel diameter:30-150 mmmax. module:6 total power requirement:36 kWweight of the machine ca.:11 tdimensions of the machine ca.:2,4 x 2,5 x 3,4 m ... mais informação

weight of the machine ca.:8 tdimensions of the machine ca.:2,95 x 1,6 x 2,36 mchucking diameter:250 mmswing diameter:265 mmx-travel:170 mmz-travel:200 mmspindle turning speed range:1.500 U/minspindle bearing diameter:100 mmPick-up machine ... mais informação

max. wheel diameter:1500 mmgear width:600 mmmax. module:16 min. module:1 total power requirement:38 kWweight of the machine ca.:18,7 tdimensions of the machine ca.:7,7 x 3,6 x 4,5 m mRetrofit in 2004, original from the 80s No internal hobbing device ... mais informação

max. wheel diameter:130 mmgear width:170 mmmax. module:3 min. module:0,5 total power requirement:48 kVAweight of the machine ca.:9 tdimensions of the machine ca.:7,64 x 3,14 x 3,25 mFor technical data, see PDF-File enclosed ... mais informação

Dressing diameter:110 Planing width:9999 min. module:0,5 max. module:10 spindle turning speed range:2800 1/minpressure angle: 15 - 25 ° °run-out tolerance:0,001 mmWeight:22 kg ... mais informação

max. wheel diameter:400 mmmax. module:10 min. module:0,3 weight of the machine ca.:11,5 tdimensions of the machine ca.:3,3 x 2,75 x 2,8 mmax. number of teeth:999 min. number of teeth:5 Width of teeth:0-300 mmpressure angle max.:30 pressure angle min.:14 workpiece weight max.:300 kgworm grinding diameter:300...205 mmwidth of grinding worm:125+0,7 / -0,5 mmboring diameter:160 H7 mmwith loading device FELSOMAT Type: FZ250 Year of construction: 2002 No tail stock

max. wheel diameter:275 mmgear width:55 mmmax. module:6,5 min. module:1,5 Face Hobbing-Continious ProcessContinuous process: The workpiece and tool (usually Spiron) rotate at the same time, and all teeth are created in one operation at the same time. Knife head has several knife groups (not arranged in a circle) Parallel tooth Conical tooth tip surface Single Item procedure: The workpiece is stationary and the tool (usually Arcon) rotates and cuts a tooth by immersing the tool. Once a tooth is cut, the tool moves out of the tooth again, the workpiece divides by one tooth width and the next tooth is cut until all teeth are finished. Knife head has arranged all knives in a circular path. Conical tooth height Parallel tooth head surfaceC28 can do both, wheel + pinion. However, a C28 must be ?prepared? for the individual part procedure. I.e. direct measuring system + part gear brake, workpie ...

workpiece diameter:38 mmworkpiece length:500 mmrack milling length - max.:610 mmprofile width:92 mmmodule range:0,3-1,3 slide stroke:760 mmdrive motor: kWelectrics - voltage/frequency:380/50 V/Hztotal power requirement:24 kWweight of the machine ca.:10 tSpline/cold Rolling Machine EX-CELL-O XK 251 with automatic loading device FELSOMAT PE03, fitted in 1999 and tailstock.A cold rolling machine, intended for non-cutting shaping of profiles, such as plug type gearing (straight or diagonal), spiral gearing, oil grooves

workpiece diameter:38 mmworkpiece length:500 mmrack milling length - max.:610 mmprofile width:92 mmmodule range:0,3-1,3 slide stroke:760 mmdrive motor: kWelectrics - voltage/frequency:380/50 V/Hztotal power requirement:52 kWweight of the machine ca.:10 tSpline/cold Rolling Machine EX-CELL-O XK 251 with automatic loading device FELSOMAT PE03, fitted in 1999 and tailstock.A cold rolling machine, intended for non-cutting shaping of profiles, such as plug type gearing (straight or diagonal), spiral gearing, oil grooves

max. wheel diameter:90 mmgear width:300 mmmax. module:3 tip circle diameter:max. 65 mmroot circle dia. min.:28 mmmax. geared Length:150 mmtool length - max.:203 mmtangential ( y-axis ):140 mmaxial ( z-axis ):400 mmTailstock ( z²-axis ):350 mmloading and unloading portal ( z³-axis ):1850 mmmilling head -swivable +/-:+ A = 40 / - A = 40 °working piece table: max. outer diameter / bore hole:120 / 45 mmfeeds X-axis:1 - 10000 mm/minfeeds Z-axis:1 - 10000 mm/minrapid power traverse in X-and Z direction:10000 m/minrapid motion - y-axis:5000 mm/minfast rapid z²-axis ( tailstock ):10000 mm/min.speeds of tool:300 - 4000 U/minworking piece table speed:0 - 1000 1/min.connected load:44 kVAvoltage:400 Vcontrol voltage:24 kWweight of the machine ca.:7500 kgdimensions of the machine ca.:3170 x 2975 x 2440 mm

weight of the machine ca.:5 t ... mais informação

weight of the machine ca.:4 t ... mais informação

 ... mais informação

max. wheel diameter:280 mmmax. module:7 weight of the machine ca.:13 ttable turning speeds:100 U/mintable diameter:250 mmmin. number of teeth:4 hob turning speeds:1500 U/minmax. hob diameter:160 cutter length max.:230 mmMachine in good condition.Available 01.08.2024 ... mais informação

max. wheel diameter:200 mmgear width:60 mmmax. module:7 weight of the machine ca.:15 ttable diameter:180 mmtable turning speeds:100 U/minhob turning speeds:750 U/minMachine in good condition, without feed, without automationAvailable 24.08.2024 ... mais informação

max. wheel diameter:600 mmmax. module:10 min. module:2 total power requirement:1,4 kWweight of the machine ca.:0,68 tdimensions of the machine ca.:1,6x0,75 mdiameter of hob:15 mmgear width:140 mm ... mais informação

max. wheel diameter:5 - 260 mmgear width:400 mmmax. module:15 min. module:0,5 gear hobbing diameter - internal:30 mmmax. helix angle:> 85 ° Aussenverz.max. helix angle:> 45° Innenverz.Testing Range vertical:400 mmdist. between centers:5 - 600 mmtable diameter:260 mmmax. table load:100 kgspeeds:30 1/mintotal power requirement:1,6 kVAweight of the machine ca.:900 kgdimensions of the machine ca.:200 x 1300 x 2150 mmCNC Gear Tester in good condition, out of OEM Test Lab.For measuring of spur and helical toothing, additional of rotationally symetric parts as true running, coaxiality, axial runout, etc. with tool changer ( 4 nos.)

max. wheel diameter:300 mmgear width:100 mmmax. module:5 workpiece turning speeds:0 - 1000 1/minwork piece - max.:1100 mmworkpiece clamping:auto. tension device number of spindle speeds:1000 1/min.spindle bearing diameter:100 mmdiameter of spindle flange:120 mmtailstock travel:80 mmweight of the machine ca.:3500 KGdimensions:1200 x 1450 x 2250 mmtotal power requirement:10 kVAThe Gear Tooth Deburring machine WERA, ZEM 300 for deburring of splines gear wheels and shafts, with Pointing Facility.

Description: Machine Type: flat superficies , Dimension grinding wheel: 300 x 40 mm Hydraulic operation , Max. grinding area: 670x470x400 mm Magnet plate , Installed power: 3.2kw  ,weight approx.: 4,000 kg, Approx. Onsite Dimension. (l x w x h): 2,800 x 1,885 x 1,900 mm ... mais informação