Fabricante:
(Categoria: 107)
sheet width: 1530 mmplate thickness: 4,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 1,25 tdimensions of the machine ca.: 2,10 x 1,85 x 1,20 m- controlled back gauge 750 mm- Continuous hold-down device with hard rubber strip- pneumatic sheet holding device- Rear area protection in accordance with the UVV safety package- POS 100 control- Extended, extendable support tableThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1040 mmplate thickness: 4,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 1,20 tdimensions of the machine ca.: mBending rail groundThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... mais informação
capacity: 3 mm; Unloading: 1450mm; Accessories included ... mais informação
1 set off tooling, 8500 power on hours Machine already ready for transport, machine can be viewed on viewing day for correct assessment. ... mais informação
working length: 3000 mmplate thickness at ST 45: 1,25 mmplate thickness at Alu ALMG3: 1,75 weight: ca. 1900 kgdimensions: 3760 x 610 x 1060 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... mais informação
4-roll Hydraulic plate bender 8000 x 40 mm. 1960 Froriep 8000Х40 mm Plate rolling machine - 4 rolls 8000Х40 mm ... mais informação
CNC bending line for bending sheets up to a thickness of 8 mm and a width of 2500 mm. The machine is being sold due to its lack of use, it was practically unused. the machine is connected, functional and can be demonstrated in action. ... mais informação
Capacity: 10 tons Includes: bend adapters Foot pedal operation ... mais informação
Hydraulic press brake 160t / 3200mm with controller E21 (automatic adjustment of the back stops). The status of the new machine Year 2016 ... mais informação
We sell Turret punch press - MP10-30 used, 2007, manufacturer JIANGSU YANGLI GROUP CO. Possible leasing, rent-to-own. They are also interested in intermediaries with a place to store equipment (they are ready to pay for rent). MP10 CNC series punching machine has a body structure (ZL2004 2 0108852.4), which adopts tempering treatment. German I + L. The hydraulic system has reliable performance and low power consumption (1 1 kW). FANUC CNC system OIS or SIEMENS 840D is used on this punch series. The revolving type (ZL 022 1821 1.X) features a long sleeve structure and the station index has a sectional wheel and a worm gear.
Valley. Crank shears with an inclined blade for a sheet of 20x2000 mm, model NLZ427B, are designed for cutting sheet metal with a thickness of up to 20 mm and a tensile strength of S 500 MPa. Scissors can be used in the procurement workshops of metal structures, machine-building enterprises, repair and other plants, when used in climatic zones with a temperate and cold climate version UHL, dry and humid tropical - version O; placement category 4 according to GOST 15150 - 69 The lower value of the air temperature must be at least +5 0С. Designed for cutting metal up to 20mm thick 1. Maximum cutting force, kN 1000 2. The largest dimensions of the metal being cut with temporary 3. resistance
Type: CTO 80/2500 Parameters: 80 t, 2500 mm Manufacturer: Strojárně Piesok Year of production / SO / GO: - / - / - Description: The machine is in good technical condition. Nominal forming force: 80t Working table length: 2500mm Maximum stroke: 150mm Maximum distance of the table from the ram: 360mm Working height: 800mm Dimensions LxWxH: 3700 x 1250 x 2385mm Machine weight: 6550kg Upon agreement, the possibility of a tour in progress.
Unused manual outcropper, heavy duty. -Max thickness 3 mm steel. -Max cutting angle: 90 x 90 mm. -Size: approx. 48w x 60d x 130h cm, without extension rod. -Height with extension bar: 215 cm. ... mais informação
The machine is in good technical condition. Max. length of cut sheet: 2000mm Max. thickness of the cut sheet: 6.3 Weight: 6725 kg Upon prior agreement, the possibility of a tour in progress. ... mais informação
LINE FOR LOWER AND CROSS-CUTTING OF COILS (annual capacity 10 000 t): Sheet thickness: from 0.4 mm to 2.0 mm Sheet width: from 800 mm to 1580 mm Material: cold rolled and galvanized sheet metal Strength limit: max. 480 MPa (for max. thickness of 1.5 mm) Yield strength: max. 250 MPa (for max. thickness of 1.5 mm) Output material parameters - cut sheets Width tolerance up to: +/- 0.1 mm according to EN 10140 Length tolerance up to: +/- 0.3 mm according to EN 10140 Maximum number of longitudinal stripes: 6 (for max. thickness 1.5 mm) Maximum number of longitudinal sections: 5 (for max. thickness 1.5 mm) Minimum width of one strip: 180 mm Minimum length of boards: 200 mm Maximum length of the boards: 3500 mm +
machine for marking and cutting rolled metal - corner TBL 2020 Production China. There are all documents. The machine was not in use, but stood for 2.5 years without observing the storage conditions, so the computer (system unit) does not work. Everything else is normal. We are ready to present the machine for inspection at any time. The machine is currently stored in a warehouse in the Republic of Tatarstan.
Parameters: 40 mm, 1500x3000 mm Description: The machine is in good technical condition, after agreement possibility of inspection. The plasma includes a power supply including burners, including acetylene burner. ... mais informação
I offer hydraulic shears not sheet metal marked NTA 3150/10A manufacturer Strojáreň Piesok. The maximum cutting length is therefore 3150 mm and the strength of the structural steel sheet is 10 mm. Plugged in, fully functional, but so rarely used that its not worth my while to keep them. (they do not fit into our primary production segment) Price negotiable, buyer arranges transport, total weight 14,000 kg Possibility of viewing, testing - at the Chrudim facility