subcategorias
(terceiro nível de categoria)
Fabricante:
(Categoria: 109)
used mechanical vertical internal clearing machine in very good condition. Pulling force at 3m/min: 3000 KG Clearance speed: 3m/min Return speed: 3m/min maximum stroke: 800mm Ropcmo87 maximum tool length: 1000mm Table area: 350mm x 220mm Table break-in: 90mm Workpiece diameter: any Dimensions (h x w x t): 1260 x 500 x 720mm Engine power: 1.1 / 1.5KW Power supply: 380 volts 50 HZ Accessories / Optional equipment: - integrated coolant / cutting agent system - Machine documentation Comment: The double spindle drive ensures a quiet and central pulling point as well as a constant clearance speed. The machine is mainly designed for the production of spring springs up to 20mm. The machine has been partially overhauled, all bearings, shaft seals and seals of the trapezoidal spindles and gearbox have been renewed. The drawing head is re-ground and adjusted, the machine body is ...
Manufacturer: Heraeus Type: TUo Year of construction: 1967 Power: 5.5 kW Temperature: 250 °C Dimensions: 600 x 600 x 550 mm ... mais informação
clamping width: 5000 mmlifting capacity: 5 tweight of the machine ca.: 4 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... mais informação
Single Stand - Eccentric Press PELS - RICHTER Type PEKR 125 Masch. No. 20684 Year of construction 1967Compressive force 125ton. Projection 430 mm Table size 1100 x 750 mm Ram surface 890 x 650 mm Table opening 400 mm Stroke adjustment 6 to 115 mm Ram adjustment 100 mm Installation height largest stroke above max. 450 mm Clamping pin bore 50 mmStroke rate 60 strokes/min. Table height above corridor 900 mm Motor power 7.5 kWMains connection 380 volts, 50 Hz- Overload protection by crushing plate in the plunger- Compressed air Clutch-brake combination DESCH- Plunge weight compensation cylinder- Manual ram position- Two-hand operation- Cam switchgear- Grease central lubrication Vögele- Stroke counterSpace requirement L x W x H 2300 x 1450 x 3030 mmWeight approx. 10 ton. good condition; used
spindle diameter: 80 mmx-travel: 1200 mmy-travel: 1000 mmz-travel: 815 mmSpindle travel: 450 mmspindle taper ISO: 40 Radial face slide diameter: 498 mmtable surface area: 1000x800 mmdigital readout: coolant: total power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Tumbling riveting machine - radial spot riveting machine KUMAGMasch. No. 67/101 Year of construction 1967Table size 330 x 280 mm Projection 215 mm Tool shank cone 8 - 10 mmRivet shank diameter 1 - 10 mm Tool stroke 30 - 40 mmOperating air pressure 1 - 6 barRivet time adjustable 0.5 sec. - 3 h motor power 0.8 kWMains connection 380 volts, 50 Hz- Conical tool shank for quick tool change- Rivet head on the column adjustable in height- Fine adjustment of the working stroke, max. 10 mm, with scale ring- Riveting force air pressure infinitely adjustable- Triggering via push-button table modelSpace requirement L x W x H 670 x 450 x 850 mmWeight 215 kggood condition; used
Univ. Tool milling machine DECKEL Type FP 1 Masch. No. 51265/08 Year of construction approx. 1967Travel routes X: 300 mm Y: 150 mm Z: 340 mm Table size 600 x 2100 mm Spindle holder SK 40 - S20 x 2 Spindle speed 40-2000 rpm 16 stepsMotor power 1.0 and 1.6kW pole switchableMains connection 380 volts, 50 Hz feed in the X and Z axes- Spindle speed over 2motor speeds and 8 gear stages - Pinole shift on the vertical milling head 60 mm - Fixed angle table - adjacent control cabinetSpace requirement L x W x H 1100 x 1100 x 1600 mmWeight 650 kggood condition; used
diameter range 8 mmnumber of dies 4number of stations (incl. cut off) 7cutting length 20-105 mmshaft length under head 85 mmoutput - pieces/min 120max. thread length 70 mmmax. width across flats 14 mm ... mais informação
bushing cut-offdiameter range 10-22 mmnumber of dies 4number of stations (incl. cut off) 7cutting length 200 mmshaft length under head 160 mmoutput - pieces/min 60max. thread length 95 mmmax. width acros flats 32 mm ... mais informação
Two multiple drawing machine Breitenbach Standard 4-III/8 are available, inlet/finished diameter: 3/ 0.8-1.5mm, drawing speed: 2-8m/s, weight: 11.17t, machine 2 is in the same design as machine 1, but set up for torsion free multiple drawing with twin pulleys, with documentation and spare pulleys, has been regularly maintained.
wire diameter 0,6-1,1 mmmesh width 3/4 inchworking width 2100 mmnumber of strokes 115-125 ... mais informação
diameter range 64 mmmax. width across flats 56 mmmax. outside dia. of round pieces 64 mmbar dia. 18-40 mmcutting length 20-72 mmoutput - pieces/min 140number of forming stations 3press power 230 t ... mais informação
diameter range 2-6 mmshaft length under head 5-50 mmoutput pieces/min 180 ... mais informação
working width: 2.000 mmnumber of line wires: max. 16distance of cross wires: 6\", 12\", 18\", 24\" od. 36\"distance of length wires: 1/2\" to 1/2\"wire diam. length wire: 2,5 - 3,25 mmwire diam. edge wire: max. 4,0 mmwire diam. cross wire: max. 3,25 mmwire diam. knot wire: max. 3,25 mm; ready for operation
Pile cutting machine, stack cutter, face cutter SCHNEIDER type Senator 155 Rubber, paper and veneer shears Masch. No. 60178 Year of construction 1968 Cutting length 1550 mm Cutting thickness approx. 125mm Application height 140 mm Backgauge max. 1550 mmMotor power Knife drive 5.5 kWMainsconnection 380 volts, 50 Hz- 2-hand operation for stroke triggering - automatic pressing by hold-down presses the stack of paper onto the table - Kickback (backgauge) with digital dimension selection and sequence cut adjustment via control- Backgauge adjustment via servo motor (motor and control has been retrofitted)Space requirement L x W x H 300 x 270 x 165 cmWeight 5100 kggood conditionIdeal for cutting paper, cardboard, leather, cork, rubber or fabric reinforced rubber; used
Weight approx. 800 kg Dimensions set-up approx. (LxWxH) 1200x900x1600 mm ... mais informação
spindle diameter: 63 mmtaper MK: 5 facing slide: ja digital: ja : ja weight of the machine ca.: 7 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... mais informação
Univ. Tool milling machine DECKEL Type FP 1 Masch. No. 52185/08 Year of construction 1968 Travel X: 300 mm Y: 150 mm Z: 340 mm Table size 600 x 250 mm Spindle holder SK 40 - S20 x 2Spindle speed 40-2000 rpm 16 stepsMotor power 1.0 and 1.4kW pole switchableMains connection 380 volts, 50 Hz feed in the X and Z axes- Two motor speeds and 8 gear stages- Pinol shift on the vertical milling head 60 mm - Fixed angle table coolant device in the machine foot - adjacent control cabinet- counter holder with counter bearing for horizontal milling SK 40 Space requirement L x W x H 1200 x 1100 x 1600 mmWeight approx. 1000kgvery good condition; used
Vertical band saw MÖSSNER REKORD type SM 420 Masch. No. 17010 Year of construction 1968 Roll diameter 420 mm Projection in width 415 mm Projection in height 265 mm Table size 605 x 600mmBelt speed 18- 562 m/min. 8 stepssaw band length min/max. 3150 / 3260 mm Drive power 1.1 / 1.7 kWMains connection 380 V 50 Hz band saw blade speed via 4 gear stages and 2 motor speeds- saw blade butt welding machine IDEAL BS 0-16 with scissors and whetstone- swivel work table in 2 axesSpace requirement L x W x H 950 x 750 x 1900 mmWeight 570 kggood condition; used