prensas usadas para venda

L 30 Kw POWER 450 Kg/h (material-dependent/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSING SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for the wood chip raw material - Pellet mill with main motor 30 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system for controlling the clogging of the matrice Moisture monitoring - Cooling and dedusting system for the pellets produced via a screw

L 45 Kw POWER 680 Kg/h (material-dependent/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSING SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for the wood chip raw material - Pellet mill with main motor 45 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system for controlling the clogging of the matrice Moisture monitoring - Cooling and dedusting system for the pellets produced via a screw

AUTOMATIC BRIQUETTING machine type COMAFER DINAMIC 85N second hand machine volt. 380/50 CE mark : Yes briquett diameter mm. 60 production from 40 kg. to 85 kg. / hour motor power Hp 7,5 net weigth kgs. 850  ... mais informação

Code: 0332 Brand: AMASPRES (ITALY) Model: 3000 Membrane press Working size: mm 3000 x 1300 Opening mm 500 Working height mm 250 Cover opening and closing with vertical pneumatic pistons This press is suitable for veneer of shaped pieces , such as window sash frames, curved pieces Upper heating with hot air Heating of lower side with hot air Consuption about 9 kwt Working cycle: about 10 min. Complete compressor for lifting of cover and under cover Processing prevacuum adjustable up to 6.5 atm The machine is equipped with time alarm, thermostat, thermometer, warning lights for calories and pumps Overall dimensions press mm 4100 x 1700 x 2050 h - Weight kg 1800 Overall dimensions depressor mm 1400 x 500 x 900 h - Weight kg 100

The pellet mill has been refurbished by us and is in as new condition. Die, roll assembly and V-belt are new. Engine power 2 x 110Kw The diameter 650mm Press width 105mm  ... mais informação

Pellet mill for ring DIE and two roll shell system. Inside diameter: 900 mm Active operating width: 138mm Active forming area: 3902 cm² Press roll Ø440/142 optionally dimpled or notched Front door Stainless steel front door with large opening angle. pneumatic operated overload bypass protection gate. Two knives with step less length adjustments integrated in the door. Machine housing All housing parts are cut by precision laser. The machine base, the base plate and the housing are welded and reinforced. Drive Drive via 355 kW-1200 rpm engine , timing belt Ø200/1900 - Beltdrive Motor and Motor cables not included. Equipment Central lubrication for roll assembly and main shaft Manual roll adjustment Overload protection provided by a safety pin Die of chrome steel X46 Cr13 with conical seat for an easy change of the die - Die is not included Adj ...

Furniture Door Frame Press V. Grum-Schwensen Type MTP Specifications: • Assembly of frame parts: fully automatic • External frame dimensions min. (mm): 120 x 120 • External frame dimensions max. (mm): 700 x 2500 • Custom size  ... mais informação

I sell several machines, equipment here. spare parts, etc. for woodworking, Forklifts, work platforms as well as accessories and spare parts for forklifts and work platforms. Therefore, be sure to check out my other auctions Briquette press briquetting press chip press Pressing unit without control WEIMA TYPE: TH50 Briquette diameter approx. 50 mm Motor power hydraulics 5.5 KW They only bid on the briquette unit incl. hydraulic power unit. there is no control. I still have a control for briquette press with LOGO module. This can be purchased at an additional cost. The power unit could not be tested. Will be sold as it says here. ( See pictures ACTUAL - condition) Prior viewing is expressly desired, just leave phone no. by mail, then I will get back to you for a viewing appointment. Subject to prior sale, all information is subject to change. The ma ...

Briceder press RSN SP 250 P Don't. # 02 782 Without a control cabinet/control Without hosting 700 l cooling water tank available for hydraulick units L x B x H: 120 x 80 x 120 cm Built in 1992 Weight about 750 kg Dismantling by buyers The machine is in good condition, operational. Changes, errors, intermediate sales reserved! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Edge press of PanHans 923 with preheating ruler Working length 250 cm maximum 80 mm thick L x W x H: 300 x 60 x 100 cm Weight approx. 300 kg Built in 1976 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

SPECIFICATIONS: Electric hot operation Work table size mm: 2500 x 1300 with intermediate plate 4 pistons, diameter mm: 90 Vertical stroke mm: 450  ... mais informação

Hydraulic frame press Hungerbühler Press-Measurement: 4100 x 3050mm 3 vertical cylinders 3 horizontal cylinders Height adjustment via control box Width adjustment via control box Supports at the bottom for gluing wings at working height. The machine is in good condition, ready for operation. Subject to change, error, prior sale ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Phone 0041 62 966 18 32 Fax: 0041 62 966 21 12

Glue stand hydraulic, double-sided Format L x W: 3000 x 2000 mm L x W x H: 3200 x 2200 x 1100 mm Weight approx. 600 kg Built in 2003 Pressure per cylinder 2500 kg 8 clamping elements 2 Holders The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Frame press Hess economic hydraulic 3600 x 2250 mm L x W x H: 400 x 100 x 270 cm Weight approx. 1100 kg year 1987 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Glue press Etienne Format L x B: 3800 x 2700 mm Window frame press pneumatic Weight approx. 890 kg Year of construction 1980 The press is in good condition, ready to use. Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Good Used Glulam Beams Press BUILD YEAR 2010 Hydraulic Preeslaenge 12 m Press height 1.3 m Machine like new  ... mais informação

SPECIFICATIONS: Rotating frame press for glulam Max. working length mm: 3000 Max. working width mm: 1200 Thickness mm: min 25 - max 90 12 charging stations Complete with "Clam Carrier" pusher  ... mais informação

SPECIFICATIONS: Dimensions of the plate mm: 2300 x 1000 Number of pistons: 04 Piston diameter mm: 60 Water operation with boiler  ... mais informação

TECHNICAL DATA: Working width mm: 3000 Working height mm: 1700 Downholders: 4  ... mais informação

TECHNICAL DATA: Working width mm: 3000 Working height mm: 1800 Downholders: 5  ... mais informação