máquinas injetoras usadas para venda

Description: Clamping force: 1,100 kN screw diameter 35 mm incl. discharge conveyor, Engel ERC 23/2-F handling robot Internal number: E 110/1 M2332 SN: 163486, Approx. Onsite Dimension. (l x w x h): 0 x 0 x 0 mm, weight approx.: 7,400 kg ... mais informação

Description: Internal number: A 100/1 2K M2357 SN: 226901 Clamping force: 1.000 kN Screw diameter H: 20 m  ,Screw diameter V: 15 mm incl. turntable, deposit conveyor, Wittmann handling robot Approx. Onsite Dimension. (l x w x h): 0 x 0 x 0 mm, weight approx.: 6,700 kg ... mais informação

Description: Serial number 161491 Clamping force: 350 kN Mould opening force, max.: 31/100 kN Size of mould platens 400 mm x 400 mm Distance between tie bars 270 mm x 270 mm Mould opening stroke: 325 mm Mould height min.: 225 mm Max daylight: 550 mm Hydraulic ejector - stroke: 125 mm Ejector force forward/backward: 31 kN Screw diameter: 30 mm Ls/D ratio: 20 Injection pressure: 2400 bar Stroke volume: 67 ccm Shot weight, PS: 56 g Injection stroke: 95 mm Screw speed: 10 - 550 1/min Nozzle pressure: 60 kN Nominal capacity of pump motor: 11 kW Installed heating capacity: 3,4 kW Reservoir capacity: 190 ltr. Operating voltage 420 V, 50 Hz Dimension 3300 cX1200 x 1500 mm Weight 1500 kg Approx. Onsite Dimension. (l x w x h): 3,300 x 1,200 x 1,500 mm, weight approx.: 1,500 kg

Description: Serial number 504171 Clamping force 500 Ton Opening stroke mm: 1260 Distance between tie bars mm: 900 x 800 Installation height min/max mm: 90 Mould fixing platen size 1270 x 1200 Screw size mm: 80 Injection shot weight in Polysterol gr: 1304 Injection volume cm³: 1433 Injection pressure increased bar: 1829 Rated voltage 400 V, 50 Hz Rated current 80 A Max. fuze rating 80 A Control voltage 24 VDC Largest MTR FLA 34 A Short circuit current rating 10 KA Dimension 7400 x 2330 x 2500 mm Weight 17000 kg Approx. Onsite Dimension. (l x w x h): 7,400 x 2,330 x 2,500 mm, weight approx.: 17,000 kg

Description: Serial number 174470 Clamping force: 2000 kN Screw diameter 45 mm Ls/D ratio: 22 Injection pressure: 2336 bar Stroke volume: 305 ccm Shot weight, PS 278 g Injection rate: 200 ccm/s Screw speed: 342 1/min Plasticising rate max.: 37 g/s Nozzle pressure: 110 kN Mould opening force, max.: 101 kN Travel force movable platen Opening: 50 kN Travel force movable platen Closing: 42 kN Size of mould platens 915 mm x 915 mm Distance between tie bars 560 mm x 560 mm Mould opening stroke: 700 mm Mould height min.: 350 mm Max daylight: 1050 mm Hydraulic ejector - stroke: 200 mm Rated voltage 400 V, 50 Hz Rated current 80 A Max. fuze rating 80 A Approx. Onsite Dimension. (l x w x h): 5,690 x 1,900 x 2,400 mm, weight approx.: 2,534 kg

Description: serial number 137300 Closing force 750 KN Size of mould platens 490 mm x 490 mm Distance between tie bars 320 mm x 320 mm Mould opening stroke: 375 mm Mould height min.: 250 mm Max daylight: 625 mm Hydraulic ejector - stroke: 150 mm Ejector force forward/backward: kN Screw diameter: 40 mm Ls/D ratio: 15 Injection pressure 1150 bar Stroke volume: 188 ccm Shot weight, PS: 158 g Injection rate: 201ccm/s Injection stroke: 150 mm Nozzle pressure: 72,3 kN Nominal capacity of pump motor: 15 kW Installed heating capacity: 5,56 kW Adjustable barrel heating zones: 3 + 1 Dry cycle time: 2 sec Reservoir capacity: 220 ltr. Operating voltage 420 V, 50 Hz Heating 5,56 kW Pump motor 15 kW Total load 20,6 kW Max. fuze rating 80 A Control voltage 24 VDC Dimension 4300 x 1850 x 1600 mm Weight 2400 kg Approx. Onsite Dimension. (l x w x h): 4,300 x 1,850 x 1,600 mm, weight approx.: 2,400 kg

Description: serial numberr 160654 Clamping force 1000 KN Mould opening force, max.: 35 / 390 kN Size of mould platens 545 mm x 545 mm Distance between tie bars 370 mm x 370 mm Mould opening stroke: 500 mm Mould height min.: 250 mm Max daylight: 750 mm Hydraulic ejector - stroke: 175 mm Ejector force forward/backward: 40 kN Injection unit Screw diameter: 35 mm Ls/D ratio: 20 Injection pressure: 1750 bar Stroke volume: 115 ccm Shot weight, PS: 121 g Injection rate: 190 ccm/s Injection stroke: 150 mm Screw speed: 513 r/min. Nozzle pressure: 70 kN Electric and Hydraulic Equipment Nominal capacity of pump motor: 18,5 kW Installed heating capacity: 5,4 kW Reservoir capacity: 240 ltr. Operating voltage 420 V, 50 Hz Total load 24,1 kW Max. fuze rating 80 A Control voltage 24 VDC Short circuit current rating 10 KA Dimension 4230 x 1500 x 1600 mm Weight 3090 kg Approx. Onsite Dimension. (l x w x ...

Description: Serial nummer 152562 Clamping force: 500 kN Mould opening force, max.: 130 Kn Size of mould platens: 400 x 400 Distance between tie bars: 270 x 270 Mould opening stroke: 325 Mould height min.: 225 Max daylight: 550 Hydraulic ejector - stroke: 125 Ejector force forward/backward: 31 Screw diameter: 30 mm Ls/D ratio: 16,5 Injection pressure: 1290 bar Stroke volume: 70 ccm Shot weight, PS: 58 g Injection rate: 165 ccm/s Injection stroke: 100 mm Screw speed: 62 m/min Nozzle pressure: 60 kN Electric and Hydraulic Equipment Nominal capacity of pump motor: 15 kW Installed heating capacity: 3,9 kW Reservoir capacity:190 ltr.Operating voltage 380 V, 50 Hz Heating 4,0 kW Pump motor 15 kW Total load 19,0 kW Max. fuze rating 80 A Control voltage 24 VDC Short circuit current rating 10 KA Dimension 3700 x 1750 x 2000 mm Weight 1720 kg Approx. Onsite Dimension. (l x w x h): 3,700 x 1,750 x ...

Description: serial numberr 177900 Clamping force 400 KN Clearance between columns: 270 mm x 270 mm Board dimensions: 446 mm x 446 mm Mold size: min. 200 mm Maximum opening distance: 350 mm Max distance between plates: 550 mm Screw diameter: 30 mm Injection volume / Injection weight: 70 ccm / 59 grams PS Injection pressure: 1550 bar Engine: 11 kW Heaters: 4.5 kW Operating voltage 400 V, 50 Hz Contrtol voltage 230 V, 50 Hz Total connected load 40,1 kW Control voltage 24 VDC Dimension 2656 x 1850 x 1476 mm Weight 2180 kg Approx. Onsite Dimension. (l x w x h): 2,565 x 1,850 x 1,476 mm, weight approx.: 2,180 kg

Description: serial number 160352 Clamping Force: 1000 kN Distance Betw. Tie-Bars: 270 mm x 270 mm Platen Size: 545 mm x 545 mm Mould Hight: min 250 mm Opening Stroke: 500 mm Max. Open Daylight: 750 mm Screw Diameter: 35 mm / 30 mm Injection Volume: 121 gram PS / 89 gram PS Injection Prresure: 1855 bar / 2350 bar Motor Power: 18,5 kW Heating Power: 5,4 kW Operating voltage 420 V, 50 Hz Heating 5,5 kW Pump motor 18,5 kW Total load 24,0 kW Dimension 4300 x 1500 x 1800 mm Weight 3850kg Approx. Onsite Dimension. (l x w x h): 4,300 x 1,500 x 1,800 mm, weight approx.: 3,850 kg

Description: Serial number 254335 Clamping force 300 T Screw diameter 50 mm Tie bar spacing (H) 630 mm Tie bar spacing (V) 630 mm Shot volume 432 cm³ Shot weight 393 g Pressure on material 2304 bar Platen length 995 mm Platen width 1050 mm Rated voltage 400 V, 50 Hz Rated current 80 A Max. fuze rating 80 A Control voltage 24 VDC Largest MTR FLA 34 A Short circuit current rating 10 KA dimension 45970 x 2040 x 2360 mm Weight 12.500 kg Approx. Onsite Dimension. (l x w x h): 45,970 x 2,040 x 2,360 mm, weight approx.: 12,500 kg

Description: serial numbe 253455 Clamping force 2500 kN Screw diameter 60 mm Mould opening force, max.: 160 kN Travel force movable platen Opening: 67 kN Travel force movable platen Closing: 62 kN Size of mould platens 900 mm x 830 mm Distance between tie bars 630 mm x 560 mm Mould opening stroke: 820 mm Mould height min.: 330 mm Max daylight: 1150 mm Injection pressure: 1778 bar Stroke volume: 678 ccm Shot weight, PS 610 g Injection rate: 565 ccm/s Screw speed: 259 1/min Plasticising rate max.: 58 g/s Nozzle pressure: 110 kN Electric and Hydraulic Equipment Nominal capacity of pump motor: 45 kW Installed heating capacity: 22,7 kW Rated voltage 400 V, 50 Hz Rated current 80 A Max. fuze rating 80 A Control voltage 24 VDC Largest MTR FLA 34 A Short circuit current rating 10 KA Dimension 8280 x 2235 x 2350 mm Weight 12600 kg Approx. Onsite Dimension. (l x w x h): 8,280 x 2,235 x 2,350 mm,  ...

Description: serial number 193178 Clamping force: 350 kN Size of mould platens 242 mm x 250 mm Distance between tie bars 221 mm Mould opening stroke: 200 mm Mould height min.: 150 - 300 mm Max daylight: 350 - 500 mm Hydraulic ejector - stroke: 60 mm Ejector force forward/backward: 24 kN Screw diameter: 25 mm Ls/D ratio: 20 Injection pressure: 2000 bar Stroke volume: 49 ccm Shot weight, PS: 45 g Injection rate: 54 ccm/s Injection stroke: 100 mm Nozzle pressure: 50 kN Nominal capacity of pump motor: 7,5 kW Installed heating capacity: 4,3 kW Adjustable barrel heating zones: 3+1 Reservoir capacity: 80 ltr.Operating voltage 400 V, 50 Hz Contrtol voltage 230 V, 50 Hz Total rated current 47 A Total connected load 26 kW Control voltage 24 VDC Dimension 2600 x 1500 x 1900 mm Weight 1120 kg Approx. Onsite Dimension. (l x w x h): 2,600 x 1,500 x 1,900 mm, weight approx.: 1,220 kg

Description: serial number 154951 Clamping force 1500 kN Mould opening force, max.: 86 kN Travel force movable platen Opening: 45 kN Travel force movable platen Closing: 34 kN Size of mould platens 840 mm x 790 mm Distance between tie bars 560 mm x 500 mm Mould opening stroke: 600 mm Mould height min.: 300 mm Max daylight: 900 mm Hydraulic ejector - stroke: 150 mm Ejector force forward/backward: 20/11 kN Screw diameter: 50 mm Ls/D ratio: 20 Injection pressure: 1892 bar Stroke volume: 377 ccm Shot weight, PS: 343 g Injection rate: 181 ccm/s Screw speed: 255 1/min Plasticising rate max.: 35 g/s Nozzle pressure: 84 kN Nominal capacity of pump motor: 22 kW Installed heating capacity: 16 kW Adjustable barrel heating zones: 5 Dry cycle number: 1700 1/h Reservoir capacity: 345 ltr. Rated voltage 400 V, 50 Hz Rated current 80 A Control voltage 24 VDC Dimension 4670 x 1480 x 2160 mm Weight 6300  ...

Description: Clamping force: 1,000 kN Screw diameter H: 20 mm Screw diameter V: 18 mm incl. turntable, deposit conveyor, Wittmann handling robot Internal number: A 100/2 2K M2358 SN: 227275 Approx. Onsite Dimension. (l x w x h): 0 x 0 x 0 mm, weight approx.: 6,700 kg ... mais informação

This HYUNDAI 450 injection moulding machine was manufactured in 2001. It features a screw diameter of 76 mm, an injection pressure of 1840 ㎏/㎠, and a mould clamping force of 450 tons. The machine has a total power capacity of 88.18 kW and a hydraulic oil reservoir with a capacity of 900 liters. This is an excellent opportunity to acquire the HYUNDAI 450 machine we have for sale. Reach out for more information.

 ... mais informação

screw size:45 mminjection shot weight in Polysterol:149 g/PSclosing pressure:1250 kN ... mais informação

Were parting with our 2 injection molding machines following a reorganization of our workshop. The 1st press were selling is an Engel 200/50 HL-ST (photos in attachment), which works well but has a few jerks during the injection phase, but is functional. The 2nd press is a Demag Ergotech 150-600 (photos in PJ), which works but has a few problems, and can no longer be considered a 150T but rather a 90T (pump wear).

Description: Machine number: 44575 Spindle diameter 25 mm Stroke 120 mm Spindle speed 380 rpm Max. screw torque 300 nm Max. injection volume 127.6 cm³/s Max. stroke volume 58,9 cm³ Max. injection pressure 2400 bar Max. injection power 42 kW Nozzle stroke 600 mm Nozzle pressure force 14 kN Installed heating power 6.8 kW Closing force 1000 kN Opening stroke 420 mm Mould installation height max. 420 mm, min. 150 mm Ejector force 23 kN Ejector stroke 130 mm Increased clamping plate 740 x 700 mm Width of ejector shaft 470 mm Dry running 1.6 s ENGEL CC 100 control system, 1 pneumatic core pull Tool heating circuits 8 Internal pressure switch KISTLER Nominal voltage : 3x400 + N+ PE /50 Hz Switching load : 95 Kw Rated current : 145 A Voltage control : 230 v AC / 24v DC Approx. Onsite Dimension. (l x w x h): 2,900 x 1,900 x 1,600 mm, weight approx.: 9,500 kg